Phase uncertainty in calibrating microwave test fixtures

The problem of phase uncertainty arising in calibration of the test fixtures is investigated in this paper, It is shown that the problem exists no matter what kinds of calibration standards are used. It is also found that there is no need to determine the individual S-parameters of the test fixtures. In order to eliminate the problem of phase uncertainty, three different precise (known) reflection standards or one known reflection standard plus one known transmission standard should be used to calibrate symmetrical test fixtures. For the asymmetrical cases, three known standards, including at least one transmission standard, should be used. The thru-open-match (TOM) and thru-short-match (TSM) techniques are the simplest methods, and they have no bandwidth limitation. When the standards are imprecise (unknown), it is recommended to use any suitable technique, such as the thru-reflect-line, line-reflect-line, thru-short-delay, thru-open-delay,line-reflect-match, line-reflect-reflect-match, or multiline methods, to accurately determine the values of the required calibration terms and, in addition, to use the TOM or TSM method with the same imprecise standards to resolve the phase uncertainty.

Frequency limitation in calibrating microwave test fixtures

The problem of frequency limitation arising in calibration of the test fixtures is investigated in this paper. It is found that at some frequencies periodically, the accuracy of the methods becomes very low, and. the denominators of the expressions of the required S-parameters approach zero. This conclusion can be drawn whether-the test fixtures, are symmetric or not. A good agreement between theory and experiment is obtained.

Direct decomposition of NO activated by microwave discharge

The environmentally friendly removal of NO has been investigated using continuous microwave discharge (CMD) at atmospheric pressure. In these experiments, conversions of NO to N-2 as well as NO2 were mainly observed for both dry and wet feed gas, which showed a great difference from those observed with other discharge methods. The effects of a series of reaction parameters, including microwave input power, O-2 concentration, NO concentration, and gas flow rate, on the product distribution and energy efficiency were also studied. Under all reaction conditions, the conversions of NO to N-2 were higher than those to NO2. The highest conversion of NO to N-2 was 88%. The reaction rate of NO removal and the effects of the different discharge modes on NO conversion and product distribution are also discussed. Through comparison of the results of different discharge modes, it was found that the addition of CH4 apparently increased the conversion of NO to N-2 as well as the energy efficiency. A possible reaction process is suggested.

Shape and Phase-Controlled Synthesis of KMgF3 Colloidal Nanocrystals via Microwave Irradiation

In this paper, we present a facile one-step route to controlled synthesis of colloidal KMgF3 nanocrystals via the thermolysis of metal trifluoroacetate precursors in combined solvents (OA/OM) using microwave irradiation. X-ray diffraction (XRD), transmission electron microscopy (TEM), thermogravimetric and differential thermal analysis (TG-DTA), Fourier transform infrared (FT-IR) spectra, and photoluminescence (PL) spectra were employed to characterize the samples. Only through the variation of the OA/OM ratio, can the phase and shape of nanocrystals be readily controlled, resulting in the formation of well-defined near-spherical nanoparticles, and nanoplates of cubic-phased KMgF3, as well as nanorods of tetragonal-phased MgF2, and a possible mechanism has been proposed to elucidate this effect. Furthermore, all these samples in this system can be well dispersed in nonpolar solvents such as cyclohexane to form stable and clear colloidal solutions, due to the successful coating of organic surfactants (OA/OM) on the nanocrystal surface.

Synthesis and characterization of Eu-doped hydroxyapatite through a microwave assisted microemulsion process

Europium doped hydroxyapatite (Eu:HAp) nanosized particles with multiform morphologies have been successfully prepared via a simple microemulsion-mediated process assisted with microwave heating. The physicochemical properties of the samples were well characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM), transmission electron microscopy (TEM), X-ray photoelectron spectra (XPS), Fourier transform infrared spectroscopy (FT-IR), photoluminescence (PL) spectra, and the kinetic decays, respectively. The results reveal that the obtained Eu:HAp particles are well assigned to the hexagonal lattice structure of the hydroxyapatite phase. Additionally, it is found that samples exhibit uniform morphologies which can be controlled by altering the pH values. Furthermore, the samples show the characteristic D-5(0)-F-7(1-4) emission lines of Eu3+ excited by UV radiation.

Rapid synthesis of hexagon-shaped gold nanoplates by microwave assistant method

The microwave (MW)-based thermal process was applied to the preparation of hexagon-shaped gold nanoplates. The fort-nation of gold nanoplates occurs rapidly in a single step, carried out by directly heating a reaction mixture of HAuCl4 with sodium citrate in an MW reactor. And the gold nanoplates were characterized by UV-visible spectroscopy, X-ray diffraction (XRD) and transmission electron microscopy (TEM). The experimental results indicated that the sizes and morphologies of the gold nanomaterials strongly depend both on the heating methods and molar ratio of HAuCl4 to sodium citrate in the initial reaction mixture. At the molar ratio 5 : 4 (HAuCl4 to sodium citrate), hexagonal nanoplates with large Au (111) crystallographic facet were preferentially synthesized by the MW assistant method.

Hydrothermal and solvothermal synthesis of the complex fluoride alpha '-SrAlF5

The complex fluoride alpha'-SrAlF5 has been synthesized through hydrothermal and solvothermal methods under mild conditions. The effects of the molar ratio of starting materials, temperature, reaction time and solvents on the synthesis of alpha'-SrAlF5 were discussed. The final products were characterized by XRD and SEM. The rod-like shape of alpha'-SrAlF5 is shown in SEM images.

A nickel molybdenum phosphate with tunnel: Hydrothermal synthesis and structure of (NH3CH2CH2NH3)(4)center dot(NH3CH2CH2NH2)center dot Na center dot[Ni2Mo12O30(PO4)(HPO4)(4)(H2PO4)(3)]center dot 6H(2)O

A nickel molybdenum phosphate, (NH3CH2CH2NH3)(4).(NH3CH2CH2NH2). Na .[Ni2Mo12O30(PO4)(HPO4)(4)(H2PO4)(3)]. 6H(2)O, invoicing molybdenum present in V oxidation, has been hydrothermally synthesized and structurally characterized by single crystal X-ray diffraction. Deep brown-red crystals are formed in the triclinic system, space group P (1) over bar, a = 12,011(2), b = 14,612(3), c = 21.252(4) Angstrom, alpha = 80.54(2)degrees, beta = 83.10(2)degrees, gamma = 76.29(2)degrees, V = 3561.4(12) Angstrom(3), Z = 2, lambda(MoK alpha) = 0.71073 Angstrom (R(F) = 0.0529 for 9880 reflections), Data mere collected on a Siemens P4 diffractometer at 20 degrees C in the range of 1.75 degrees < theta < 23.02 degrees using the omega-scan technique. The structure was solved by direct methods using the program SHELXTL-93 and refined with the method of fun-matrix least-squares on F-2. The structure of the title compound may be considered to be two [Mo6O15(HPO4)(H2PO4)(3)](5-) units bonded together with a nickel atom, although several P-O groups are not protonated on account of coordination with a Na+ cation, The one-dimensional tunnels were formed in the solid of the title compound. A probe reaction of the oxidation of acetaldehyde with H2O2 using the title compound as catalyst was carried out in a liquid- solid system, showing that the title compound had high catalytic activity in the reaction, (C) 1999 Academic Press.

Hydrothermal synthesis and crystal structure of Co(En)(3)MoO4

Co(En)(3)MoO4 was synthesized by using the method of hydrothermal synthesis and characterized by elemental analysis, IR, ESR and single-crystal X-ray methods. It crystallizes in hexagonal space group P (3) over bar C1 with a=1.596 4(2) nm, b=1.596 4(2) nm, c = 0.993 5(2) nm, alpha=beta=90 degrees gamma=120 degrees, M-c=399.18, V=2.192 6(6) nm(3), D-c=1.814 g/nm(3), Z=6, F(000)=1 2181 R-1=0.070 3, R-w=0.220 7. According to separation of anion which acted on electrostatic potential, the anion and cation ions formed a type of organic and inorganic material.

Synthesis of a high-permeance NaA zeolite membrane by microwave heating

Zeolite membranes with high permeance and separation factors are highly desirable for practical applications. Although, in the past, very good separation factors have been obtained, it has proved difficult to achieve a high permeance. Ken a comparative study of microwave versus conventional heating in the hydrothermal synthesis of NaA zeolite membranes is made. It is demonstrated that membranes prepared by microwave heating have not only a higher permeance but also a considerably shorter synthesis time. These observations are rationalized by examining the mechanism of membrane formation.

Synthesis of NaA zeolite membrane by microwave heating

The synthesis of NaA zeolite membrane on a porous alpha -Al2O3 support by microwave heating (MH) was investigated. The formation of a NaA zeolite membrane was drastically promoted by MH. The synthesis time was reduced from 3 h for conventional heating (CH) to 15 min for MH. Surface seeding cannot only promote the formation of NaA zeolite on the support, but also inhibit the transformation of NaA zeolite into other types of zeolites. The thickness of the NaA zeolite membrane synthesized by MH was about 4 mum, thinner than that of NaA zeolite membrane synthesized by CH. The permeance of NaA zeolite membrane synthesized by MH was four times higher than that of the NaA zeolite membrane synthesized by CH, while their permselectivities were comparable. Multi-stage synthesis resulted in the transformation of NaA zeolite into other types of zeolites, and the perfection of the as-synthesized membrane decreased.

Titanium species in titanium silicalite TS-1 prepared by hydrothermal method

The titanium species existing in titanium silicalite TS-1, which is prepared by hydrothermal method, were investigated using chemical analysis, XRD, FT-IR, Si-29 MAS NMR, UV-VIS, ESR. It has been observed that several kinds of titanium species may exist in titanium silicalite. The form that titanium atoms incorporate into the framework of titanium silicalite synthesized using tetrapropylammonium bromide (TPABr) as template differs from that using the classical method. But, the symmetry of titanium silicalite, changes from monoclinic to orthorhombic with the increase of titanium content in both methods. The Ti-O-2(-) originated from framework titanium and H2O2 has the moderate stability and may be active site in oxidation reaction. TS-1 synthesized using TPABr as template does not contain anatase, but contains a kind of partly condensed titanium species with six-fold coordination. The titanium species may correspond to 270-280 mn band in UV-VIS spectra and also can form Ti-O-2(-). But, this kind of Ti-O-2(-) is very stable and cannot be catalytic active site. So, the six-fold coordination titanium species may be inactive in both the oxidation reaction and the decomposition of H2O2. The hypothesis has been further proved by the phenomena that the titanium species is easily washed off using acid, and acid treating will not influence the catalytic performance of TS-1. (C) 2001 Elsevier Science B.V. All rights reserved.

Synthesis of zeolite NaA membranes with high permeance under microwave radiation on mesoporous-layer-modified macroporous substrates for gas separation

This article reported the NaA zeolite membranes with high permeance synthesized with microwave heating method under different conditions: (1) on a macroporous substrate in gel, (11) on a mesoporous/macroporous (top-mesoporous-layer-modified macroporous) substrate in gel, and (111) on a mesoporous/macroporous substrate in sol. In general, the H-2 permeance of the NaA membranes by microwave heating in gel was usually at the level of 10(-6) mol s(-1) m(-2) Pa-1, much higher than that by the conventional hydrothermal synthesis. At similar H-2/C3H8 permselectivity. On the substrate modified mesoporous top layer, the H-2 permeance of the NaA membranes by microwave heating in gel or sol was further enhanced, while maintaining comparable H-2/C3H8 permselectivity, due to the prevention of penetration of the reagent into the pores of the macroporous substrate. Meanwhile, the synthesis took less time in sol than in gel on the mesoporous/macroporous substrate. The NaA membranes synthesized in sol had larger permeance than those in gel and underwent transformation in shorter time. The permeation of C3H8 suggested that there existed unwanted intercrystalline pores or defects in the membranes. © 2005 Elsevier B.V. All rights reserved.

Heat and mass transfer in two-phase porous materials under intensive microwave heating

Computational results for the intensive microwave heating of porous materials are presented in this work. A multi-phase porous media model has been developed to predict the heating mechanism. Combined finite difference time-domain and finite volume methods were used to solve equations that describe the electromagnetic field and heat and mass transfer in porous media. The coupling between the two schemes is through a change in dielectric properties which were assumed to be dependent both on temperature and moisture content. The model was able to reflect the evolution of both temperature and moisture fields as well as energy penetration as the moisture in the porous medium evaporates. Moisture movement results from internal pressure gradients produced by the internal heating and phase change.

A new computational approach to microwave heating of two-phase porous materials

Computational results for the microwave heating of a porous material are presented in this paper. Combined finite difference time domain and finite volume methods were used to solve equations that describe the electromagnetic field and heat and mass transfer in porous media. The coupling between the two schemes is through a change in dielectric properties which were assumed to be dependent on both temperature and moisture content. The model was able to reflect the evolution of both temperature and moisture fields as well as energy penetration as the moisture in the porous medium evaporates. Moisture movement results from internal pressure gradients produced by the internal heating and phase change.