Performance and radial distribution profiles of a variable flow rate sprinkler developed for precision irrigation

Variable rate sprinklers (VRS) have been developed to promote localized water application of irrigated areas. In Precision Irrigation, VRS permits better control of flow adjustment and, at the same time, provides satisfactory radial distribution profiles for various pressures and flow rates are really necessary. The objective of this work was to evaluate the performance and radial distribution profiles of a developed VRS which varies the nozzle cross sectional area by moving a pin in or out using a stepper motor. Field tests were performed under different conditions of service pressure, rotation angles imposed on the pin and flow rate which resulted in maximal water throw radiuses ranging from 7.30 to 10.38 m. In the experiments in which the service pressure remained constant, the maximal throw radius varied from 7.96 to 8.91 m. Averages were used of repetitions performed under conditions without wind or with winds less than 1.3 m s-1. The VRS with the four stream deflector resulted in greater water application throw radius compared to the six stream deflector. However, the six stream deflector had greater precipitation intensities, as well as better distribution. Thus, selection of the deflector to be utilized should be based on project requirements, respecting the difference in the obtained results. With a small opening of the nozzle, the VRS produced small water droplets that visually presented applicability for foliar chemigation. Regarding the comparison between the estimated and observed flow rates, the stepper motor produced excellent results.

Experimental Study on Friction between Saline Ice and Steel

Understanding the interaction of sea ice with offshore structures is of primary importance for the development of technology in cold climate regions. The rheological properties of sea ice (strength, creep, viscosity) as well as the roughness of the contact surface are the main factors influencing the type of interaction with a structure. A device was developed and designed and small scale laboratory experiments were carried out to study sea ice frictional interaction with steel material by means of a uniaxial compression rig. Sea-ice was artificially grown between a stainless steel piston (of circular cross section) and a hollow cylinder of the same material, coaxial to the former and of the same surface roughness. Three different values for the roughness were tested: 1.2, 10 and 30 μm Ry (maximum asperities height), chosen as representative values for typical surface conditions, from smooth to normally corroded steel. Creep tests (0.2, 0.3, 0.4 and 0.6 kN) were conducted at T = -10 ºC. By pushing the piston head towards the cylinder base, three different types of relative movement were observed: 1) the piston slid through the ice, 2) the piston slid through the ice and the ice slid on the surface of the outer cylinder, 3) the ice slid only on the cylinder surface. A cyclic stick-slip motion of the piston was detected with a representative frequency of 0.1 Hz. The ratio of the mean rate of axial displacement to the frequency of the stick-slip oscillations was found to be comparable to the roughness length (Sm). The roughness is the most influential parameter affecting the amplitude of the oscillations, while the load has a relevant influence on the their frequency. Guidelines for further investigations were recommended. Marco Nanetti - seloselo@virgilio.it

Studio delle comunicazioni intraspecifiche in Anarsia lineatella Zeller

Sebbene Anarsia lineatella sia un fitofago ormai da anni introdotto e diffuso in Italia, ancora poco si conosce circa le sue abitudini riproduttive. In considerazione della elevata dannosità di A. lineatella nei pescheti del nord Italia e delle scarse conoscenze sulla sua biologia, si è evidenziata la necessità di approfondire la conoscenza di questo fitofago. Pertanto gli scopi di questa ricerca hanno riguardato l’approfondimento delle conoscenze sui sistemi di comunicazione intraspecifici utilizzati da A. lineatella; la valutazione dell’efficacia di diverse miscele di feromone sintetico, in laboratorio utilizzando anche densità diverse di popolazioni di anarsia e in campo utilizzando gabbie di accoppiamento appositamente costruite, posizionate in frutteti a conduzione biologica nel nord Italia e messe a confronto con gabbie che utilizzavano come fonte attrattiva femmine vergini di tre giorni di età. Sono state condotte prove sul comportamento di maschi di A. lineatella di differenti età in risposta al feromone emesso da femmine vergini di tre giorni di età e al feromone emesso da erogatori di materiale plastico contenenti differenti miscele di feromone sintetico. Sono stati condotti studi per verificare l’influenza del contenuto di alcol ((E)5-10:OH) nella miscela feromonica sulla capacità di inibizione degli accoppiamenti, sottoponendo gli insetti a differenti concentrazioni di feromone in modo da verificare eventuali differenze di attività delle diverse miscele, differenze che emergerebbero con evidenza maggiore alle minori concentrazioni. Alcune prove sono state effettuate anche con differenti densità di popolazione, poiché una maggiore densità di popolazione determina una maggiore probabilità di accoppiamento, evidenziando più chiaramente i limiti di efficacia della miscela utilizzata. Inoltre sono state effettuate prove di campo per confrontare due modelli di erogatore per la confusione sessuale di anarsia contenenti miscele con differenti percentuali di alcol Inoltre, poiché nei pescheti la presenza di A. lineatella è pressoché sempre associata a quella di Cydia molesta e l’applicazione del metodo della confusione deve spesso essere applicato per controllare entrambi gli insetti, può risultare vantaggioso disporre di un unico erogatore contenente entrambi i feromoni; è stato quindi valutato un erogatore contenente una miscela dei due feromoni per verificare eventuali interazioni che possano ridurre l’efficacia.

Prove accelerate per la verifica strutturale di trattrici agricole

The needs of customers to improve machinery in recent years have driven tractor manufacturers to reduce product life and development costs. The most significant efforts have concentrated on the attempt to decrease the costs of the experimental testing sector. The validation of the tractor prototypes are presently performed with a replication of a particularly unfavourable condition a defined number of times. These laboratory tests do not always faithfully reproduce the real use of the tractor. Therefore, field tests are also carried out to evaluate the prototype during real use, but it is difficult to perform such tests for a period of time long enough to reproduce tractor life usage. In this context, accelerated tests have been introduced in the automotive sector, producing a certain damage to the structure in a reduced amount of time. The goal of this paper is to define a methodology for the realization of accelerated structural tests on a tractor, through the reproduction of real customer tractor usage. A market analysis was performed on a 80 kW power tractor and a series of measures were then taken to simulate the real use of the tractor. Subsequently, the rainflow matrixes of the signals were extrapolated and used to estimate the tractor loadings for 10 years of tractor life. Finally these loadings were reproduced on testing grounds with special road pavements. The results obtained highlight the possibility of reproducing field loadings during road driving on proving grounds (PGs), but the use of two field operations is also necessary. The global acceleration factor obtained in this first step of the methodology is equal to three.

Measurement of volatile organic compounds and total OH reactivity in the atmosphere

Volatile organic compounds play a critical role in ozone formation and drive the chemistry of the atmosphere, together with OH radicals. The simplest volatile organic compound methane is a climatologically important greenhouse gas, and plays a key role in regulating water vapour in the stratosphere and hydroxyl radicals in the troposphere. The OH radical is the most important atmospheric oxidant and knowledge of the atmospheric OH sink, together with the OH source and ambient OH concentrations is essential for understanding the oxidative capacity of the atmosphere. Oceanic emission and / or uptake of methanol, acetone, acetaldehyde, isoprene and dimethyl sulphide (DMS) was characterized as a function of photosynthetically active radiation (PAR) and a suite of biological parameters, in a mesocosm experiment conducted in the Norwegian fjord. High frequency (ca. 1 minute-1) methane measurements were performed using a gas chromatograph - flame ionization detector (GC-FID) in the boreal forests of Finland and the tropical forests of Suriname. A new on-line method (Comparative Reactivity Method - CRM) was developed to directly measure the total OH reactivity (sink) of ambient air. It was observed that under conditions of high biological activity and a PAR of ~ 450 μmol photons m-2 s-1, the ocean acted as a net source of acetone. However, if either of these criteria was not fulfilled then the ocean acted as a net sink of acetone. This new insight into the biogeochemical cycling of acetone at the ocean-air interface has helped to resolve discrepancies from earlier works such as Jacob et al. (2002) who reported the ocean to be a net acetone source (27 Tg yr-1) and Marandino et al. (2005) who reported the ocean to be a net sink of acetone (- 48 Tg yr-1). The ocean acted as net source of isoprene, DMS and acetaldehyde but net sink of methanol. Based on these findings, it is recommended that compound specific PAR and biological dependency be used for estimating the influence of the global ocean on atmospheric VOC budgets. Methane was observed to accumulate within the nocturnal boundary layer, clearly indicating emissions from the forest ecosystems. There was a remarkable similarity in the time series of the boreal and tropical forest ecosystem. The average of the median mixing ratios during a typical diel cycle were 1.83 μmol mol-1 and 1.74 μmol mol-1 for the boreal forest ecosystem and tropical forest ecosystem respectively. A flux value of (3.62 ± 0.87) x 1011 molecules cm-2 s-1 (or 45.5 ± 11 Tg CH4 yr-1 for global boreal forest area) was derived, which highlights the importance of the boreal forest ecosystem for the global budget of methane (~ 600 Tg yr-1). The newly developed CRM technique has a dynamic range of ~ 4 s-1 to 300 s-1 and accuracy of ± 25 %. The system has been tested and calibrated with several single and mixed hydrocarbon standards showing excellent linearity and accountability with the reactivity of the standards. Field tests at an urban and forest site illustrate the promise of the new method. The results from this study have improved current understanding about VOC emissions and uptake from ocean and forest ecosystems. Moreover, a new technique for directly measuring the total OH reactivity of ambient air has been developed and validated, which will be a valuable addition to the existing suite of atmospheric measurement techniques.

Digitale Einstrahl-Holographie atmosphärischer Eiskristalle

Es wurde ein für bodengebundene Feldmessungen geeignetes System zur digital-holographischen Abbildung luftgetragener Objekte entwickelt und konstruiert. Es ist, abhängig von der Tiefenposition, geeignet zur direkten Bestimmung der Größe luftgetragener Objekte oberhalb von ca. 20 µm, sowie ihrer Form bei Größen oberhalb von ca. 100µm bis in den Millimeterbereich. Die Entwicklung umfaßte zusätzlich einen Algorithmus zur automatisierten Verbesserung der Hologrammqualität und zur semiautomatischen Entfernungsbestimmung großer Objekte entwickelt. Eine Möglichkeit zur intrinsischen Effizienzsteigerung der Bestimmung der Tiefenposition durch die Berechnung winkelgemittelter Profile wurde vorgestellt. Es wurde weiterhin ein Verfahren entwickelt, das mithilfe eines iterativen Ansatzes für isolierte Objekte die Rückgewinnung der Phaseninformation und damit die Beseitigung des Zwillingsbildes erlaubt. Weiterhin wurden mithilfe von Simulationen die Auswirkungen verschiedener Beschränkungen der digitalen Holographie wie der endlichen Pixelgröße untersucht und diskutiert. Die geeignete Darstellung der dreidimensionalen Ortsinformation stellt in der digitalen Holographie ein besonderes Problem dar, da das dreidimensionale Lichtfeld nicht physikalisch rekonstruiert wird. Es wurde ein Verfahren entwickelt und implementiert, das durch Konstruktion einer stereoskopischen Repräsentation des numerisch rekonstruierten Meßvolumens eine quasi-dreidimensionale, vergrößerte Betrachtung erlaubt. Es wurden ausgewählte, während Feldversuchen auf dem Jungfraujoch aufgenommene digitale Hologramme rekonstruiert. Dabei ergab sich teilweise ein sehr hoher Anteil an irregulären Kristallformen, insbesondere infolge massiver Bereifung. Es wurden auch in Zeiträumen mit formal eisuntersättigten Bedingungen Objekte bis hinunter in den Bereich ≤20µm beobachtet. Weiterhin konnte in Anwendung der hier entwickelten Theorie des ”Phasenrandeffektes“ ein Objekt von nur ca. 40µm Größe als Eisplättchen identifiziert werden. Größter Nachteil digitaler Holographie gegenüber herkömmlichen photographisch abbildenden Verfahren ist die Notwendigkeit der aufwendigen numerischen Rekonstruktion. Es ergibt sich ein hoher rechnerischer Aufwand zum Erreichen eines einer Photographie vergleichbaren Ergebnisses. Andererseits weist die digitale Holographie Alleinstellungsmerkmale auf. Der Zugang zur dreidimensionalen Ortsinformation kann der lokalen Untersuchung der relativen Objektabstände dienen. Allerdings zeigte sich, dass die Gegebenheiten der digitalen Holographie die Beobachtung hinreichend großer Mengen von Objekten auf der Grundlage einzelner Hologramm gegenwärtig erschweren. Es wurde demonstriert, dass vollständige Objektgrenzen auch dann rekonstruiert werden konnten, wenn ein Objekt sich teilweise oder ganz außerhalb des geometrischen Meßvolumens befand. Weiterhin wurde die zunächst in Simulationen demonstrierte Sub-Bildelementrekonstruktion auf reale Hologramme angewandt. Dabei konnte gezeigt werden, dass z.T. quasi-punktförmige Objekte mit Sub-Pixelgenauigkeit lokalisiert, aber auch bei ausgedehnten Objekten zusätzliche Informationen gewonnen werden konnten. Schließlich wurden auf rekonstruierten Eiskristallen Interferenzmuster beobachtet und teilweise zeitlich verfolgt. Gegenwärtig erscheinen sowohl kristallinterne Reflexion als auch die Existenz einer (quasi-)flüssigen Schicht als Erklärung möglich, wobei teilweise in Richtung der letztgenannten Möglichkeit argumentiert werden konnte. Als Ergebnis der Arbeit steht jetzt ein System zur Verfügung, das ein neues Meßinstrument und umfangreiche Algorithmen umfaßt. S. M. F. Raupach, H.-J. Vössing, J. Curtius und S. Borrmann: Digital crossed-beam holography for in-situ imaging of atmospheric particles, J. Opt. A: Pure Appl. Opt. 8, 796-806 (2006) S. M. F. Raupach: A cascaded adaptive mask algorithm for twin image removal and its application to digital holograms of ice crystals, Appl. Opt. 48, 287-301 (2009) S. M. F. Raupach: Stereoscopic 3D visualization of particle fields reconstructed from digital inline holograms, (zur Veröffentlichung angenommen, Optik - Int. J. Light El. Optics, 2009)

Verhalten von Recycling-Materialien in der Umwelt : Labor- und Feldversuche

Im Baugewerbe fallen jährlich mehrere Millionen Tonnen an Baureststoffen an, die nach erfolgter Aufbereitung als Recycling-Baustoffe erneut verwendet werden können. Allerdings besteht Unklarheit hinsichtlich der Stofffreisetzung aus Recycling-Materialien sowie der Parameter, die zur Beurteilung im Wesentlichen heranzuziehen sind. Des Weiteren gilt es der Frage nachzugehen, welche Laborversuche eine realistische Prognose zum Stoffaustrag unter Freilandbedingungen ermöglichen. Ein Ergebnisvergleich aus Feld- und Laborversuchen mit Recycling-Materialien zeigt, dass weder Ammoniumnitrat-Extraktion, pH-stat Versuch noch S4- und Modifizierter S4-Test genauere Prognosen zum Stoffaustrag unter Freilandbedingungen ermöglichen. Mit einem Langzeit-Standtest sowie Schüttelversuchen mit unterschiedlichen Wasser/Feststoff-Verhältnissen lässt sich der Einfluss durch verschiedene Korngrößen sowie Materialabrieb besser kontrollieren. Diese Versuchskombination erlaubt Rückschlüsse auf die Löslichkeit und Verfügbarkeit von Stoffen in den Recycling-Materialien. Die Ergebnisse aus Säulenversuchen weisen auf eine gute Vergleichbarkeit mit den Feldversuchen hin, was sich an denselben vorherrschenden Prozessen bei der Freisetzung für eine Reihe von Stoffen zeigt. Bei mehreren Stoffen treten ähnliche Konzen-trationshöchstwerte bei Säulen- und Feldversuch auf, ebenso zeigt der Vergleich aufsummierter Massenanteile für den Säulenversuch, dass bei einer Reihe von Stoffen eine grobe Abschätzbarkeit für eine Langzeitprognose unter Freilandbedingungen existiert. Als wesentliche Parameter für die Stofffreisetzung aus den Recycling-Materialien sind neben CO2-Einfluss und pH-Wert ebenfalls Temperatureinfluss, Material-Heterogenität sowie einzusetzende Korngröße anzusehen.

Assessment of the resilience of coral reefs to natural and human disturbances by means of recruitment panels in Indo-Pacific

Indo-Pacific region encompasses about 75% of world's coral reefs, but hard coral cover in this region experienced a 32% region-wide decline since 1970s. This great change is primarily ascribable to natural and anthropogenic pressures, including climate change and human activities effects. Coral reef conservation requires management strategies oriented to maintain their diversity and the capacity to provide ecosystem goods and services. Coral reef resilience, i.e. the capacity to recover after disturbances, is critical to their long-term persistence. The aims of the present study were to design and to test field experiments intended to measure changes in recruitment processes, as a fundamental aspect of the coral reef resilience. Recruitment experiments, using artificial panels suspended in the water column, were carried out in two Indo-Pacific locations affected by different disturbances: a new mine in Bangka Island (Indonesia), and the increased sedimentation due to coastal dynamics in Vavvaru Island (Maldives). One (or more) putatively disturbed site(s) was selected to be tested against 3 randomly selected control sites. Panels’ arrangement simulates 2 proximities to living corals, i.e. the sources of propagules: few centimetres and 2 meters over. Panels were deployed simultaneously at each site and left submerged for about five months. Recruits were identified to the lowest possible taxonomic level and recruited assemblages were analysed in terms of percent cover. In general it was not possible to detect significant differences between the benthic assemblages recruited in disturbed and control sites. The high variability observed in recruits assemblages structure among control sites may be so large to mask the possible disturbance effects. Only few taxa showed possible effects of the disturb they undergo. The field tests have highlighted strengths and weaknesses of the proposed approach and, based on these results, some possible improvements were suggested.

Boundary condition identification of a bridge pier using experimental data and FEM modal updating

Over the past twenty years, new technologies have required an increasing use of mathematical models in order to understand better the structural behavior: finite element method is the one mostly used. However, the reliability of this method applied to different situations has to be tried each time. Since it is not possible to completely model the reality, different hypothesis must be done: these are the main problems of FE modeling. The following work deals with this problem and tries to figure out a way to identify some of the unknown main parameters of a structure. This main research focuses on a particular path of study and development, but the same concepts can be applied to other objects of research. The main purpose of this work is the identification of unknown boundary conditions of a bridge pier using the data acquired experimentally with field tests and a FEM modal updating process. This work doesn’t want to be new, neither innovative. A lot of work has been done during the past years on this main problem and many solutions have been shown and published. This thesis just want to rework some of the main aspects of the structural optimization process, using a real structure as fitting model.

[Prevalence of hereditary diseases in three-year-old Swiss Warmblood horses]

The objective of this study was to investigate clinical signs indicating hereditary diseases like equine sarcoid, osteochondrosis (OC) and the idiopathic laryngeal hemiplegia (ILH), and to demonstrate relationships between environment, feeding habits and conformation ("exterieur" evaluation) of the horses. For this purpose, we analyzed veterinary examinations of 403 stallions at the approvals since 1994 examined 493 three-year-old Swiss Warmblood horses, which were shown at the Swiss-Field-Tests in 2005.With the help of the owners a questionnaire on health, environment and feeding habits of the animals was completed. At the same time, the horses were assessed and graded for their "exterieur" (type, conformation, gaits) by judges of the Swiss Sporthorse breeding association. In 11.5% of horses sarcoids were found, 8.7% showed one and 2.8% several tumors.The prevalence of sarcoids in offspring of sires with known sarcoids was not significantly higher than in descendants from stallions without a known history of sarcoids. We found distended joints as a possible symptom of OC in 11.4% of the horses, 3.9% (n = 19) in both tarsal joints.We did not find a relationship between enlarged joints in the offspring and the presence of OC in the sires. Abnormal respiratory noise at work, as a possible sign for ILH, was heard only in 1.2% (n = 6). It is important to note that while we found a high number of sarcoid affected horses compared to other studies, presence of enlarged joints was not very frequent and very few horses showed abnormal respiratory noise. Additionally, we found no correlation between "exterieur" marks and the horse's general health.

Basistests Suisse Sport Test Konzept: Validierung einer sportmotorischen Basistestbatterie für den Schul- und Nachwuchssport

Physical fitness can be evaluated in competitive and school sports with different field tests under different conditions and goals. To produce valid results, a field test must be practical and reach high standards of test criteria (objectivity, reliability, validity). The purpose of this study was to investigate the test criteria and the practicability of a group of field tests called «SUISSE Sport Test Konzept Basis Feldtestbatterie». For 20-m sprint, ventral trunk muscle test, standing long jump, 2-kg medicine ball shot, obstacle course and cooper-test, test quality and practicability were evaluated. 221 children and adolescents from competitive sports and different school levels took part in the study. According to school level, they were divided into 3 groups (P: 7–11.5 y, S1: 11.6–15.5 y, S2: 15.6–21.8 y). Objectivity was tested for time or distance measurement in all tests as well as for error rating in obstacle test. For reliability measurement, 162 subjects performed the field tests twice within a few weeks. For validity results of standing long jump were compared with counter movement jump performance on a force plate. Correlation analysis was performed and level of significance was set for p < 0.05. For accuracy standard error was calculated. All tests achieved sufficient to excellent objectiv - ity with correlation-coefficient (r) lying between 0.85 and 0.99. Reliability was very good (r = 0.84–0.97). In cooper- and trunk test, reliability was higher for athletes than for pupils (trunk test: r = 0.95 vs. r = 0.62, cooper-test: r = 0.90 vs. r = 0.78). In those tests the reliability decreases with increasing age (cooper-test: P: r = 0.84, S1: r = 0.69, S2: r = 0.52; trunk-test: P: r = 0.69, S1: r = 0.71; S2: r = 0.39). Validity for standing long jump was good (r = 0.75–0.86). The standard error of the mean was between 4–8%, with the exception for cooper-test (athletes: 6%, pupils: 11%) and trunk test (athletes: 14%, pupils: 46%). The results show that the evaluated group of field tests is a practicable, objective and reliable tool to determine physical skills in young athletes as well as in a scholar setting over a broad age range. Most of the tests achieved the test criteria with the grades good to excellent. The lower coefficient of reliability for cooper- and trunk test by the pupils could be explained by motivational problems in this setting. For up to 20 subjects, a tester can accomplish the tests within 3 h. Finally, age-dependent grades were elaborated

MiniCASCC - A battery driven fog collector for ecosystem research

We developed a small version of the Caltech active strand cloud water collector (CASCC) for biogeochemical investigations in ecological applications. The device is battery powered and thus allows operation at locations where mains power is not available. The collector is designed for sampling periods of up to one week, depending on fog frequency. Our new device is equipped with standard sensors for air temperature, relative humidity, wind, and horizontal visibility for fog detection with a low-cost optical sensor. In mountain areas and during times when clouds are thin the installation of the visibility sensor became a key issue, which limits the potential to estimate liquid water content of the sampled fog. Field tests with 5 devices at three different sites in the Swiss Alps (Niesen) and the Jura Mountains (Lägeren, Switzerland) during two extended summer seasons in 2006 and 2007 showed that in almost all cases it was possible to obtain sample volumes which were large enough for the examination of basic inorganic chemistry of the collected cloud water. Collection rates varied typically from 12 to 30 mL h− 1. The fog droplet cutoff diameter is ≈ 6 μm, which is low enough to include all droplet sizes that are relevant for the liquid water content of typical fog types in the collected samples. From theoretical assumptions of the collection efficiency and theoretical droplet spectra it is possible to estimate the liquid water content of the sampled fog or cloud. Our new fog collector can be constructed and operated at relatively low costs. In combination with chemical and isotopic analyses of the sampled water, this allows to quantify nutrient and pollutant fluxes as is typically needed in ecosystem biogeochemistry studies.

Fixed and Flexible: Coexistence of Obligate and Facultative Migratory Strategies in a Freshwater Fish

Migration is an important event in many animal life histories, but the degree to which individual animals participate in seasonal migrations often varies within populations. The powerful ecological and evolutionary consequences of such partial migration are now well documented, but the underlying mechanisms are still heavily debated. One potential mechanism of partial migration is between-individual variation in body condition, where animals in poor condition cannot pay the costs of migration and hence adopt a resident strategy. However, underlying intrinsic traits may overrule such environmental influence, dictating individual consistency in migratory patterns. Unfortunately, field tests of individual consistency compared to the importance of individual condition on migratory propensity are rare. Here we analyse 6 years of field data on roach migration, gathered by tagging almost 3000 individual fish and monitoring their seasonal migrations over extended periods of time. Our aims were to provide a field test of the role of condition in wild fish for migratory decisions, and also to assess individual consistency in migratory tendency. Our analyses reveal that (1) migratory strategy, in terms of migration/residency, is highly consistent within individuals over time and (2) there is a positive relationship between condition and the probability of migration, but only in individuals that adopt a migratory strategy at some point during their lives. However, life-long residents do not differ in condition to migrants, hence body condition is only a good predictor of migratory tendency in fish with migratory phenotypes and not a more general determinant of migratory tendency for the population. As resident individuals can achieve very high body condition and still remain resident, we suggest that our data provides some of the first field evidence to show that both facultative and obligate strategies can co-exist within populations of migratory animals.

Heritabilities of health traits in Swiss Warmblood horses

REASONS FOR PERFORMING THE STUDY: There is a lack of evidence regarding genetic parameters of health traits in Swiss Warmblood horses. OBJECTIVES: To estimate heritabilities of equine sarcoid disease, horn quality of the hooves, prognathism and increased filling of talocrural joints as a possible indicator for osteochondrosis in Swiss Warmblood horses examined at the field tests for 3-year-olds between 2005 and 2013. STUDY DESIGN: Retrospective analysis of breed society database. METHODS: Swiss Warmblood horses were examined clinically by 13 veterinarians at field tests in Switzerland between 2005 and 2013. The presence of sarcoids, horn quality of the hooves, incisor occlusion and increased joint filling were assessed and recorded. Records of 3715 horses were integrated in a pedigree comprising 217,282 horses. Variance components and heritabilities were estimated on the liability scale using MTGSAM. RESULTS: The prevalences of the examined traits were rather low, ranging from 2.4 to 13.0%. Heritabilities estimated were 0.21 ± 0.07 for the occurrence of sarcoids, 0.04 ± 0.02 for hooves with markedly brittle and friable horn quality, 0.03 ± 0.01 for hooves with marked growth ring formation, 0.06 ± 0.03 for prognathism and 0.08 ± 0.04 for increased filling of the talocrural joint (an indicator of possible osteochondrosis). The influence of the examiner on the variance of these observations was considerable. CONCLUSIONS: With the exception of equine sarcoid disease, estimates for the heritabilities for the traits examined here were low. A standardised examination protocol may reduce the variance due to the examiner. This article is protected by copyright. All rights reserved. This article is protected by copyright. All rights reserved.

Crecimiento, captura de luz y componentes del rendimiento del haba cv. Alameda creciendo en Azul, provincia de Buenos Aires

La fijación de N por los cultivos de leguminosas puede ser un buen componente dentro de un plan general de mejora de la eficiencia del sistema agrícola. Para lograrlo, se debe establecer la adecuación de los cultivos a los ambientes específicos. El objetivo de este trabajo es evaluar el crecimiento del haba Alameda en el agroclima de Azul. Para alcanzar dicho objetivo se realizaron ensayos de campo en condiciones no limitantes utilizando el haba cv. Alameda desde el invierno de 2008 en la chacra experimental de la Facultad de Agronomía de Azul (Universidad del Centro de la Provincia de Buenos Aires), con cinco fechas de siembra desde mediados de julio a mediados de noviembre; también se realizó un seguimiento de algunos índices agrometeorológicos. La fecha de siembra tuvo una fuerte influencia sobre la producción de biomasa, rendimiento en grano y sus componentes. Ese efecto fue asociado con los cambios en la captura de radiación fotosintéticamente activa. Las fechas de siembra tempranas interceptaron más radiación a lo largo de la estación de crecimiento que las fechas de siembra de primavera. La primera y la segunda fechas de siembras (mediados de julio y mediados de agosto, respectivamente) tuvieron los valores más altos en producción. Las siembras de primavera (cuarta fecha: mediados de octubre; quinta fecha: mediados de noviembre) presentaron los rendimientos más bajos en granos, los que decrecieron a medida que se atrasó la fecha de siembra, con menor número de vainas por m2 y más bajo peso de mil semillas.