Energy Harvesting for Autonomous Underwater Vehicles

In this study, energy production for autonomous underwater vehicles is investigated. This project is part of a bigger project called TURTLE. The autonomous vehicles perform oceanic researches at seabed for which they are intended to be kept operational underwater for several months. In order to ful l a long-term underwater condition, powerful batteries are combined with \micro- scale" energy production on the spot. This work tends to develop a system that generates power up to a maximum of 30 W. Latter energy harvesting structure consists basically of a turbine combined with a generator and low-power electronics to adjust the achieved voltage to a required battery charger voltage. Every component is examined separately hence an optimum can be de ned for all, and subsequently also an overall optimum. Di erent design parameters as e.g. number of blades, solidity ratio and cross-section area are compared for di erent turbines, in order to see what is the most feasible type. Further, a generator is chosen by studying how ux distributions might be adjusted to low velocities, and how cogging torque can be excluded by adapted designs. Low-power electronics are con gured in order to convert and stabilize heavily varying three-phase voltages to a constant, recti ed voltage which is usable for battery storage. Clearly, di erent component parameters as maximum power and torque are matched here to increase the overall power generation. Furthermore an overall maximum power is set up for achieving a maximum power ow at load side. Due to among others typical low velocities of about 0.1 to 0.5 m/s, and constructing limits of the prototype, the vast range of components is restricted to only a few that could be used. Hence, a helical turbine is combined in a direct drive mode to a coreless-stator axial- ux permanent-magnet generator, from which the output voltage is adjusted subsequently by a recti er, impedance matching unit, upconverter circuit and an overall control unit to regulate di erent component parameters. All these electronics are combined in a closed-loop design to involve positive feedback signals. Furthermore a theoretical con guration for the TURTLE vehicle is described in this work and a solution is proposed that might be implemented, for which several design tests are performable in a future study.

Cohesive law estimation of adhesive joints in mode II condition

The adhesive bonding technique enables both weight and complexity reduction in structures that require some joining technique to be used on account of fabrication/component shape issues. Because of this, adhesive bonding is also one of the main repair methods for metal and composite structures by the strap and scarf configurations. The availability of strength prediction techniques for adhesive joints is essential for their generalized application and it can rely on different approaches, such as mechanics of materials, conventional fracture mechanics or damage mechanics. These two last techniques depend on the measurement of the fracture toughness (GC) of materials. Within the framework of damage mechanics, a valid option is the use of Cohesive Zone Modelling (CZM) coupled with Finite Element (FE) analyses. In this work, CZM laws for adhesive joints considering three adhesives with varying ductility were estimated. The End-Notched Flexure (ENF) test geometry was selected based on overall test simplicity and results accuracy. The adhesives Araldite® AV138, Araldite® 2015 and Sikaforce® 7752 were studied between high-strength aluminium adherends. Estimation of the CZM laws was carried out by an inverse methodology based on a curve fitting procedure, which enabled a precise estimation of the adhesive joints’ behaviour. The work allowed to conclude that a unique set of shear fracture toughness (GIIC) and shear cohesive strength (ts0) exists for each specimen that accurately reproduces the adhesive layer’ behaviour. With this information, the accurate strength prediction of adhesive joints in shear is made possible by CZM.

Does it pay to be social responsible? Portuguese SMEs feedback

The research on corporate social responsibility has been focused mainly on Anglo-Saxon countries and big companies. Most scholars agree there is a positive relationship between companies social and economic performance, however, this is not unanimous. Moreover,during economic downturns, companies struggle for survival and might consider corporate social responsibility efforts should be postponed. This research investigates if there is a positive relationship between social performance and key business results using a large sample of small and medium Portuguese companies over an extended period of time. The research results support the existence of valid positive relationships between companies’ social performance and key business results, confirming it does pay to invest in corporate social responsibility even in less favorable economic scenarios and for small and medium companies across all business sectors.

Influência do treino do passo rápido voluntário nas estratégias de feedforward e feedback em Adultos mais Velhos

Introdução:O envelhecimento influencia negativamente o controlo postural, diminuindo a capacidade de recuperar o equilíbrio após uma perturbação externa e consequentemente aumento do risco de queda nos adultos mais velhos Objetivo(s):Verificar a influência do treino do passo rápido voluntário nas estratégias de feedforward e feedback em adultos mais velhos aquando o stepping anterior e posterior, bem como o timing e sequência de ativação muscular, ajustes posturais antecipatórios (APA) e compensatórios (APC1,APC2), comprimento, latência, velocidade média (VM) do passo e estratégias de passo lateral Métodos:19 participantes foram distribuídos aleatoriamente por dois grupos, o grupo experimental (n=9) e o grupo controlo (n=10), estudo randomizado controlado. Ambos foram submetidos a um protocolo de exercício físico durante 3 meses, 2 vezes/semana. Adicionalmente o grupo experimental (GE) realizou o treino do passo rápido voluntário bilateral nas várias direções. A resposta a um desequilíbrio postural em vários sentidos e consequente resposta de stepping anterior, posterior ou lateral foram avaliadas por meio de eletromiografia de superfície e por um sistema de imagem 3D Resultados: Na variação entre o momento inicial e final (M0-M1), durante o stepping anterior o GE, comparativamente ao GC, aumentou e diminuiu significativamente o timing do RF ipsilateral e GemM, respetivamente. Na variação do timing dos músculos BF ipsilateral e contralateral e TA contralateral, o GE diminuiu significativamente menos do que o GC. O GE aumentou significativamente o comprimento do stepping posterior do que o GC. Quanto à variação da latência observou-se que o GE aumentou significativamente do que o GC nos dois steppings. Na variação da VM, do stepping anterior, o GE diminuiu significativamente mais do que GC. O GE aumentou e diminuiu significativamente os APAS e os APC1 do que o GC no stepping posterior e anterior, respetivamente. Verificou-se que a estratégia mais frequente nos dois momentos e grupos foi a estratégia de stepping lateral direto Conclusão: A contínua prática do stepping rápido voluntário parece promover um melhor controlo postural sendo um importante exercício específico para prevenção de quedas

Pipelined analog-to-digital conversion using current-mode reference shifting

Dissertação para obtenção do grau de Mestre em Engenharia Electrotécnica e de Computadores

Design and implementation of 3D buildings integration for a Webgl-Based Virtual Globe: a case study of Valencian Cadastre and Fide Building Mode

Dissertation submitted in partial fulfillment of the requirements for the Degree of Master of Science in Geospatial Technologies.

The significance of Traveler's Route Knowledge for Choice of commuting mode of transport

Dissertation submitted in partial fulfillment of the requirements for the Degree of Master of Science in Geospatial Technologies.

Reference-free high-speed cmos pipeline analog-to-digital converters

Submitted in partial fulfillment of the requirements for the degree of Doctor of Philosophy in Electrical and Computer Engineering of the Faculdade de Ciências e Tecnologia of Universidade Nova de Lisboa

EDP InovCity: Electricity feedback with smart meters through tv

A Work Project, presented as part of the requirements for the Award of a Masters Degree in Management from the NOVA – School of Business and Economics

Verification of analog circuits in power-down mode

Dissertação para obtenção do Grau de Mestre em Engenharia Eletrotécnica e Computadores

A 1.2 V low noise amplifier with double feedback for high gain and low noise figure

Dissertação para obtenção do Grau de Mestre em Engenharia Eletrotécnica e de Computadores

Referenda outcomes and the influence of polls: A social network feedback process

This paper proposes a model to explain the differences between outcomes of referenda and the voting trends suggested by polls. Two main effects are at stake. First, the evolution of the voters' attitudes is conditional on the public information made available to them. Second, the predisposition toward abstention among individuals within each voting group may be different. Our model describes how these two aspects of decision making may interact, showing how publicly available information may amplify the distinct tendency toward abstention between both groups and thus affect the outcome of the referendum.

Target-specific multiphysics modeling for thermal medicine applications

Dissertation to obtain the degree of Doctor of Philosophy in Biomedical Engineering

O feedback/la retroalimentación na avaliação da oralidade nas aulas de língua estrangeira

Relatório de Estágio apresentado para cumprimento dos requisitos necessários à obtenção do grau de Mestre em Ensino do Inglês e de Línguas Estrangeiras no 3º ciclo do Ensino Básico e no Secundário

Improving Learners’ Motivation through Feedback in English Language Teaching and Learning at Polytechnic School in Benguela, Angola

Currently, it is widely perceived among the English as a Foreign Language (EFL) teaching professionals, that motivation is a central factor for success in language learning. This work aims to examine and raise teachers’ awareness about the role of assessment and feedback in the process of language teaching and learning at polytechnic school in Benguela to develop and/or enhance their students’ motivation for learning. Hence the paper defines and discusses the key terms and, the techniques and strategies for an effective feedback provision in the context under study. It also collects data through the use of interview and questionnaire methods, and suggests the assessment and feedback types to be implemented at polytechnic school in Benguela