Effets des procédés d’usinage de finition sur les propriétés de surface, la performance d’un vernis et l’émission de poussières du bois de chêne rouge

La performance d’un produit de finition sur le bois est influencée par la manière dont la surface est préparée. Le ponçage est très utilisé pour préparer les surfaces lors de la finition. Toutefois, ce procédé génère une grande quantité de poussières. Ainsi, les effets des procédés d’usinage sur les propriétés de surface, la performance d’un vernis et l’émission de poussières ont été étudiés dans le but de déterminer les modes de préparation des surfaces les plus adéquats pour le bois de chêne rouge. Dans un premier volet, les propriétés de surface et la performance d’un vernis ont été évaluées sur les surfaces préparées à l’aide du procédé traditionnel de ponçage et de trois procédés alternatifs de rabotage soit la coupe périphérique droite, la coupe hélicoïdale et la coupe oblique. La qualité de surface a été évaluée au moyen des caractéristiques de rugosité, d’endommagement cellulaire et de mouillabilité. Des essais de résistance à l’adhésion d’un vernis d’usage intérieur ont été effectués avant et après un traitement de vieillissement accéléré. Les résultats ont montré que le ponçage a induit une rugosité et un niveau de fibrillation supérieurs à ceux des autres procédés, ainsi qu’une mouillabilité et une adhésion du vernis après vieillissement accéléré élevées. Les surfaces rabotées avec la coupe périphérique droite ont présenté un certain niveau de fibrillation, une rugosité et une mouillabilité intermédiaires. Néanmoins, l’adhésion du vernis après vieillissement a été également inférieure par rapport aux autres procédés. La coupe hélicoïdale a produit une rugosité intermédiaire. D’autre part, la coupe oblique a été le procédé qui a présenté une perte d’adhésion après vieillissement similaire au ponçage. Ce procédé a généré des surfaces lisses avec rugosité et mouillabilité intermédiaires. Sur la base des résultats obtenus, le ponçage à l’aide d’un programme P100-grain et une vitesse d’avance de 7 m/min, la coupe périphérique droite avec un angle d’attaque de 25° et une onde d’usinage de 1,0 mm, la coupe hélicoïdale avec une onde d’usinage de 1,0 mm et la coupe oblique realisé avec un angle oblique de 15° ont permis d’obtenir les meilleures conditions d’usinage pour chaque procédé. Dans un deuxième volet, l’effet de différents paramètres de coupe sur l’émission de poussières et la rugosité de la surface a été étudié lors de la coupe hélicoïdale. Les émissions de poussières ont diminué avec la diminution de laprofondeur de coupe et l’augmentation de l’épaisseur moyenne du copeau. Cependant, les surfaces obtenues avec l’épaisseur moyenne du copeau plus élevée ont présenté une rugosité supérieure. Par contre, si une surface plus lisse est requise, une vitesse d’avance intermédiaire doit être utilisée afin de diminuer la rugosité des surfaces sans exposer les travailleurs à des niveaux élevés de poussière de bois. Par ailleurs, l’émission de poussières pour chaque fraction de particules peut être estimée à travers les modèles développés.

Relações interorganizacionais e confiança no setor da carcinicultura: um estudo de caso na camanor produtos marinhos

This study investigated how the types of confidence based on competence and good will act in the formation and maintenance of cooperation relationships between the Camanor and its partners (Aquatec, Purina, Caçuá, Uvifrios and Malta / Cleyton). It used organizational approaches on networks based primarily on studies of Powell (1987, 1990), Das and Teng (2000, 2001), Child (2001) and Contractor and Lorange (2004) which have described the advantages that cooperative relationships can provide, as well as their limits as alternative governance structures. Confidence has been considered an important factor affecting the actions and development of organizations involved in networks or in strategic alliances (ZAHEER; HARRIS, 2006) and is the most appropriate control mechanism in these situations (SYDOW, 1998). Confidence is seen from two different approaches: the economic and the sociological (ZAHEER; HARRIS, 2006). To facilitate the understanding of confidence some typologies have been created, as proposed by Barney and Hansen (1994), Lane (1998), Das and Teng (2000), Child (2001) and Wever, Martens and Vandenbempt (2005). This study made use of the case study as proposition of Yin (2005). Semi-structured interviews were held with pre-determined routes, in a single stage performed in early 2008. The research subjects were owners and / or responsible for Camanor and its business partners (Aquatec, Purina, Caçuá, Uvifrios and Malta / Cleyton). Also secondary data were collected in several sites related to the industry and enterprises studied, in addition to data collected by previous studies conducted by CARCINEREDES (2006). The primary data were analyzed using the analysing technique of the content proposed by Bardin (1994). Regarding the secondary data, they were qualitatively analyzed according to documentary analysis technique (BARDIN, 1994). Thus, through the data collected, could be concluded that although there is confidence based on good faith in relationships(UZZI, 1998; OF; TENG, 2001), their presence does not determine the formation and / or maintenance of a partnership, serves only in order to facilitate the relationship, making them more flexible. The confidence based on competence (DAS; TENG, 2001) influenced the formation and maintenance of relations studied. Because whether or not to form a relationship with another organization it is used the perception of the partner acts, namely the reputation (image) as decision basis. And it is through the verification of the performance of the partner activities that will determine the continuation of the partnership

Estudo térmico dos resíduos gerados da destilação atmosférica das misturas diesel/biodiesel de dendê

The growing world demand for energy supplied by fossil fuels, a major contributor to the emission of pollutants into the atmosphere and causing environmental problems, has been encouraging governments and international organizations to reflect and encourage the use of alternative renewable sources. Among these new possibilities deserves attention biodiesel, fuel cleaner and easy to reproduce. The study of new technologies involving that source is necessary. From this context, the paper aims at analyzing the thermal stability by thermogravimetric analysis, of the waste generated from atmospheric distillation of mixtures with ratios of 5, 10, 15 and 20% palm biodiesel in diesel with and without addition of BHT antioxidant. It was synthesized biodiesel through palm oil, via homogeneous catalysis in the presence of KOH, with and without the use of BHT and subsequently added to the diesel common indoor type (S1800) from a gas station BR. The diesel was already added with 5% biodiesel, and thus the proportions used for these blends were subtracted from the existing ratio in diesel fuel, resulting in the following proportions palm oil biodiesel: 0% (B5), 5% (B10), 10 % (B15) and 15% (B20). From atmospheric distillation analysis, performed in mixtures with and without BHT were collected residue generated by each sample and performed a thermal study from the thermogravimetric analysis at a heating rate of 10 °C.min-1, nitrogen atmosphere and heating to 600 ° C. According to the specifications of Resolution No. 7/2008 for biodiesel, it was found that the material was synthesized in accordance with the specifications. For mixtures, it was noted that the samples were in accordance with the ANP Resolution No. 42/2009. Given the TG / DTG curves of the samples of waste mixtures with and without BHT antioxidant was able to observe that they showed a single stage of thermal decomposition attributed to decomposition of heavy hydrocarbons and esters and other heavier constituents of the waste sample weighed. The thermal behavior of residues from atmospheric distillation of mixtures of diesel / biodiesel is very important to understand how this affects the proper functioning of the engine. A large amount of waste can generate a high content of particulate material, coke formation and carbonaceous deposits in engine valves, compromising their performance

Avancement vers la synthèse du (+) et du (-)-hodgsonox

Ce mémoire décrit les travaux qui ont été réalisés sur la synthèse de l’hodgsonox, un sesquiterpène tricyclique comportant un éther diallylique dans un cycle tétrahydropyranique. Les approches envisagées sont la formation du cycle à cinq puis la formation du tétrahydropyrane et une autre plus convergente qui implique la synthèse des deux cycles en une seule étape. La première partie du mémoire discute de la synthèse d’un précurseur acyclique du cycle à cinq membres, afin de réaliser une réaction de métathèse de fermeture de cycle. Toutefois, les essais n’ont pas été concluants et cette voie a été abandonnée. Dans la deuxième partie, une nouvelle approche impliquant la synthèse d’un bicycle par une réaction de Pauson-Khand a été étudiée. Le précurseur de la réaction de Pauson- Khand a été préparé en 9 étapes (30% de rendement global) à partir du diéthyle tartrate. Le produit de cyclisation a été également obtenu mais il n’a pas été possible par la suite d’introduire le groupement isopropyle. Dans la dernière partie de ce mémoire, les travaux de Lise Brethous sur la synthèse de l’hodgsonox ont été repris. Celle-ci avait montré que le cycle à 5 membres pouvait être obtenu à partir de l’a-acétyl g-butyrolactone et que la formation du bicycle pouvait être réalisée par une réaction catalytique d’insertion d’un composé diazoïque dans un lien O-H. Certaines de ces étapes ont été optimisées et différents tests ont été effectués pour réaliser les dernières étapes de la synthèse de l’hodgosonox, mais sans succès.

Avancement vers la synthèse du (+) et du (-)-hodgsonox

Ce mémoire décrit les travaux qui ont été réalisés sur la synthèse de l’hodgsonox, un sesquiterpène tricyclique comportant un éther diallylique dans un cycle tétrahydropyranique. Les approches envisagées sont la formation du cycle à cinq puis la formation du tétrahydropyrane et une autre plus convergente qui implique la synthèse des deux cycles en une seule étape. La première partie du mémoire discute de la synthèse d’un précurseur acyclique du cycle à cinq membres, afin de réaliser une réaction de métathèse de fermeture de cycle. Toutefois, les essais n’ont pas été concluants et cette voie a été abandonnée. Dans la deuxième partie, une nouvelle approche impliquant la synthèse d’un bicycle par une réaction de Pauson-Khand a été étudiée. Le précurseur de la réaction de Pauson- Khand a été préparé en 9 étapes (30% de rendement global) à partir du diéthyle tartrate. Le produit de cyclisation a été également obtenu mais il n’a pas été possible par la suite d’introduire le groupement isopropyle. Dans la dernière partie de ce mémoire, les travaux de Lise Brethous sur la synthèse de l’hodgsonox ont été repris. Celle-ci avait montré que le cycle à 5 membres pouvait être obtenu à partir de l’a-acétyl g-butyrolactone et que la formation du bicycle pouvait être réalisée par une réaction catalytique d’insertion d’un composé diazoïque dans un lien O-H. Certaines de ces étapes ont été optimisées et différents tests ont été effectués pour réaliser les dernières étapes de la synthèse de l’hodgosonox, mais sans succès.

A NEW DC UPS FOR DC POWER DISTRIBUTION SYSTEM IN DATA CENTER

In recent years, the 380V DC and 48V DC distribution systems have been extensively studied for the latest data centers. It is widely believed that the 380V DC system is a very promising candidate because of its lower cable cost compared to the 48V DC system. However, previous studies have not adequately addressed the low reliability issue with the 380V DC systems due to large amount of series connected batteries. In this thesis, a quantitative comparison for the two systems has been presented in terms of efficiency, reliability and cost. A new multi-port DC UPS with both high voltage output and low voltage output is proposed. When utility ac is available, it delivers power to the load through its high voltage output and charges the battery through its low voltage output. When utility ac is off, it boosts the low battery voltage and delivers power to the load form the battery. Thus, the advantages of both systems are combined and the disadvantages of them are avoided. High efficiency is also achieved as only one converter is working in either situation. Details about the design and analysis of the new UPS are presented. For the main AC-DC part of the new UPS, a novel bridgeless three-level single-stage AC-DC converter is proposed. It eliminates the auxiliary circuit for balancing the capacitor voltages and the two bridge rectifier diodes in previous topology. Zero voltage switching, high power factor, and low component stresses are achieved with this topology. Compared to previous topologies, the proposed converter has a lower cost, higher reliability, and higher efficiency. The steady state operation of the converter is analyzed and a decoupled model is proposed for the converter. For the battery side converter as a part of the new UPS, a ZVS bidirectional DC-DC converter based on self-sustained oscillation control is proposed. Frequency control is used to ensure the ZVS operation of all four switches and phase shift control is employed to regulate the converter output power. Detailed analysis of the steady state operation and design of the converter are presented. Theoretical, simulation, and experimental results are presented to verify the effectiveness of the proposed concepts.

The initial phase of sodium sulfite pulping of softwood : A comparison of different pulping options

Single stage and two-stage sodium sulfite cooking were carried out on either spruce, pine or pure pine heartwood chips to investigate the influence of several process parameters on the initial phase of such a cook down to about 60 % pulp yield. The cooking experiments were carried out in the laboratory with either a lab-prepared or a mill-prepared cooking acid and the temperature and time were varied. The influences of dissolved organic and inorganic components in the cooking liquor on the final pulp composition and on the extent of side reactions were investigated. Kinetic equations were developed and the activation energies for delignification and carbohydrate dissolution were calculated using the Arrhenius equation. A better understanding of the delignification mechanisms during bisulfite and acid sulfite cooking was obtained by analyzing the lignin carbohydrate complexes (LCC) present in the pulp when different cooking conditions were used. It was found that using a mill-prepared cooking acid beneficial effect with respect to side reactions, extractives removal and higher stability in pH during the cook were observed compared to a lab-prepared cooking acid. However, no significant difference in degrees of delignification or carbohydrate degradation was seen.  The cellulose yield was not affected in the initial phase of the cook however; temperature had an influence on the rates of both delignification and hemicellulose removal. It was also found that the  corresponding activation energies increased in the order:  xylan, glucomannan, lignin and cellulose. The cooking temperature could thus be used to control the cook to a given carbohydrate composition in the final pulp. Lignin condensation reactions were observed during acid sulfite cooking, especially at higher temperatures. The LCC studies indicated the existence of covalent bonds between lignin and hemicellulose components with respect to xylan and glucomannan. LCC in native wood showed the presence of phenyl glycosides, ϒ-esters and α-ethers; whereas the α-ethers  were affected during sulfite pulping. The existence of covalent bonds between lignin and wood polysaccharides might be the rate-limiting factor in sulfite pulping.

Cordectomía por sustracción pedicular en la columna dorsal y lumbar en fracturas traumáticas: experiencia en el hospital universitario mayor Mederi y revisión sistemática de la literatura

Objetivo: Presentar la experiencia con la técnica de corpectomia por sustracción pedicular en fracturas traumática a nivel de la columna dorsal y Lumbar en el Hospital Universitario Mayor en Bogotá y hacer una revisión sistemática de la literatura de esta técnica quirúrgica. Material y métodos: Se realizó un análisis retrospectivo de las historias clínicas de pacientes que consultaron al servicio de neurocirugía entre los años 2013 y 2015 con fracturas traumáticas a nivel de la columna dorsal y lumbosacra. Se realizó un análisis de déficit neurológico pre y posoperatorio por medio de la Clasificación neurológica estándar de lesión medular (ASIA), al igual que tiempos de cirugía, sangrado intraoperatorio y complicaciones. A su vez se realiza una revisión sistemática de la literatura sobre esta técnica quirúrgica. Resultados: El total de pacientes que se sometieron a cirugía fue de 32, de los cuales el tiempo quirúrgico promedio fue de 396 min, se obtuvo un ASIA prequirúrgico B: 50% C: 47% y E: 3%. El ASIA post operatorio fue de B: 9% C: 47% D: 38% E: 6%. Se obtuvo una mejoría del déficit neurológico en el 75% los pacientes intervenidos. El promedio de sangrado fue de 1,223 cc. Se tuvieron 4 complicaciones, 2 hematomas en lecho quirúrgico que requirió re intervención y dos fistulas de líquido cefalorraquídeo las cuales se manejaron con vendaje compresivo y reposo absoluto. Conclusiones: La corpectomia por sustracción pedicular requiere de un adecuado entrenamiento y un grupo multidisciplinario dentro de los que se incluye neuroanestesiologo, a su vez de neurocirujanos entrenados en columna. Este abordaje presenta grandes beneficios como disminución de tiempos quirúrgicos, disminución de sangrado intraoperatorio y disminución de morbilidad entre otras.

Tratamiento quirúrgico del síndrome de apnea hipopnea obstructiva del sueño en la Clínica Rivas, Bogotá – Colombia

Introducción: El Síndrome de Apnea Hipopnea Obstructiva del Sueño es un trastorno respiratorio del sueño mayor ampliamente conocido, con importantes implicaciones para los pacientes y cuya incidencia ha venido en aumento durante los últimos años; comprende diversas manifestaciones clínicas que varían desde el ronquido hasta consecuencias cardiovasculares importantes. Objetivo: Describir la experiencia de los procedimientos quirúrgicos más utilizados para el tratamiento de pacientes con Trastornos Respiratorios del Sueño en la Clínica Rivas. Diseño: Estudio observacional descriptivo. Métodos: Revisión de 366 historias clínicas de pacientes con diagnóstico clínico y Polisomnográfico de SAHOS intervenidos quirúrgicamente debido al Trastorno Respiratorio del Sueño por rechazo de terapia de presión positiva en 3 años de observación. Resultados: Se evaluaron diferencias en medianas de los cambios del IAH, índice de Saturación de oxigeno basal y mínima, y el índice de microdespertares nocturnos tanto prequirúrgica como postquirúrgicamente. Como medida de evaluación secundaria se evaluaron las complicaciones quirúrgicas. Conclusión: En nuestra institución, como centro de referencia en apnea del sueño, la cirugía ha demostrado que disminuye de forma significativa gravedad del SAHOS y disminuye el riesgo de los pacientes con trastornos respiratorios del sueño que han rechazado el dispositivo de presión positiva.

Dynamic Modeling and Seasonal Performance Evaluation of Air-to-Water Heat Pump Systems

In this Thesis a series of numerical models for the evaluation of the seasonal performance of reversible air-to-water heat pump systems coupled to residential and non-residential buildings are presented. The exploitation of the energy saving potential linked to the adoption of heat pumps is a hard task for designers due to the influence on their energy performance of several factors, like the external climate variability, the heat pump modulation capacity, the system control strategy and the hydronic loop configuration. The aim of this work is to study in detail all these aspects. In the first part of this Thesis a series of models which use a temperature class approach for the prediction of the seasonal performance of reversible air source heat pumps are shown. An innovative methodology for the calculation of the seasonal performance of an air-to-water heat pump has been proposed as an extension of the procedure reported by the European standard EN 14825. This methodology can be applied not only to air-to-water single-stage heat pumps (On-off HPs) but also to multi-stage (MSHPs) and inverter-driven units (IDHPs). In the second part, dynamic simulation has been used with the aim to optimize the control systems of the heat pump and of the HVAC plant. A series of dynamic models, developed by means of TRNSYS, are presented to study the behavior of On-off HPs, MSHPs and IDHPs. The main goal of these dynamic simulations is to show the influence of the heat pump control strategies and of the lay-out of the hydronic loop used to couple the heat pump to the emitters on the seasonal performance of the system. A particular focus is given to the modeling of the energy losses linked to on-off cycling.

Planning and flexible operation of storage systems in power grids: from transmission to distribution networks

The first part of the thesis has been devoted to the transmission planning with high penetration of renewable energy sources. Both stationary and transportable battery energy storage (BES, BEST) systems have been considered in the planning model, so to obtain the optimal set of BES, BEST and transmission lines that minimizes the total cost in a power network. First, a coordinated expansion planning model with fixed transportation cost for BEST devices has been presented; then, the model has been extended to a planning formulation with a distance-dependent transportation cost for the BEST units, and its tractability has been proved through a case study based on a 190-bus test system. The second part of this thesis is then devoted to the analysis of planning and management of renewable energy communities (RECs). Initially, the planning of photovoltaic and BES systems in a REC with an incentive-based remuneration scheme according to the Italian regulatory framework has been analysed, and two planning models, according to a single-stage, or a multi-stage approach, have been proposed in order to provide the optimal set of BES and PV systems allowing to achieve the minimum energy procurement cost in a given REC. Further, the second part of this thesis is devoted to the study of the day-ahead scheduling of resources in renewable energy communities, by considering two types of REC. The first one, which we will refer to as “cooperative community”, allows direct energy transactions between members of the REC; the second type of REC considered, which we shall refer to as “incentive-based”, does not allow direct transactions between members but includes economic revenues for the community shared energy, according to the Italian regulation framework. Moreover, dispatchable renewable energy generation has been considered by including producers equipped with biogas power plants in the community.

High performance battery chargers for full electric and hybrid cars

This Doctoral Thesis aims to study and develop advanced and high-efficient battery chargers for full electric and plug-in electric cars. The document is strictly industry-oriented and relies on automotive standards and regulations. In the first part a general overview about wireless power transfer battery chargers (WPTBCs) and a deep investigation about international standards are carried out. Then, due to the highly increasing attention given to WPTBCs by the automotive industry and considering the need of minimizing weight, size and number of components this work focuses on those architectures that realize a single stage for on-board power conversion avoiding the implementation of the DC/DC converter upstream the battery. Based on the results of the state-of-the-art, the following sections focus on two stages of the architecture: the resonant tank and the primary DC/AC inverter. To reach the maximum transfer efficiency while minimizing weight and size of the vehicle assembly a coordinated system level design procedure for resonant tank along with an innovative control algorithm for the DC/AC primary inverter is proposed. The presented solutions are generalized and adapted for the best trade-off topologies of compensation networks: Series-Series and Series-Parallel. To assess the effectiveness of the above-mentioned objectives, validation and testing are performed through a simulation environment, while experimental test benches are carried out by the collaboration of Delft University of Technology (TU Delft).

Nebivolol Reduces Central Blood Pressure In Stage I Hypertensive Patients: Experimental Single Cohort Study.

Assessment of central blood pressure (BP) has grown substantially over recent years because evidence has shown that central BP is more relevant to cardiovascular outcomes than peripheral BP. Thus, different classes of antihypertensive drugs have different effects on central BP despite similar reductions in brachial BP. The aim of this study was to investigate the effect of nebivolol, a β-blocker with vasodilator properties, on the biochemical and hemodynamic parameters of hypertensive patients. Experimental single cohort study conducted in the outpatient clinic of a university hospital. Twenty-six patients were recruited. All of them underwent biochemical and hemodynamic evaluation (BP, heart rate (HR), central BP and augmentation index) before and after 3 months of using nebivolol. 88.5% of the patients were male; their mean age was 49.7 ± 9.3 years and most of them were overweight (29.6 ± 3.1 kg/m2) with large abdominal waist (102.1 ± 7.2 cm). There were significant decreases in peripheral systolic BP (P = 0.0020), diastolic BP (P = 0.0049), HR (P < 0.0001) and central BP (129.9 ± 12.3 versus 122.3 ± 10.3 mmHg; P = 0.0083) after treatment, in comparison with the baseline values. There was no statistical difference in the augmentation index or in the biochemical parameters, from before to after the treatment. Nebivolol use seems to be associated with significant reduction of central BP in stage I hypertensive patients, in addition to reductions in brachial systolic and diastolic BP.

Clinical utility of a molecular test in adjuvant treatment decision making in women with endocrine-sensitive early stage breast cancer: a retrospective, single center one year experience

Background. Molecular tests for breast cancer (BC) risk assessment are reimbursed by health insurances in Switzerland since the beginning of year 2015. The main current role of these tests is to help oncologists to decide about the usefulness of adjuvant chemotherapy in patients with early stage endocrine-sensitive and human epidermal growth factor receptor 2 (HER2)-negative BC. These gene expression signatures aim at predicting the risk of recurrence in this subgroup. One of them (OncotypeDx/OT) also predicts distant metastases rate with or without the addition of cytotoxic chemotherapy to endocrine therapy. The clinical utility of these tests -in addition to existing so-called "clinico-pathological" prognostic and predictive criteria (e.g. stage, grade, biomarkers status)-is still debated. We report a single center one year experience of the use of one molecular test (OT) in clinical decision making. Methods. We extracted from the CHUV Breast Cancer Center data base the total number of BC cases with estrogen-receptor positive (ER+), HER2-negative early breast cancer (node negative (pN0) disease or micrometastases in up to 3 lymph nodes) operated between September 2014 and August 2015. For the cases from this group in which a molecular test had been decided by the tumor board, we collected the clinicopathologic parameters, the initial tumor board decision, and the final adjuvant systemic therapy decision. Results. A molecular test (OT) was done in 12.2% of patients with ER + HER2 negative early BC. The median age was 57.4 years and the median invasive tumor size was 1.7 cm. These patients were classified by ODX testing (Recurrence Score) into low-, intermediate-, and high risk groups, respectively in 27.2%, 63.6% and 9% of cases. Treatment recommendations changed in 18.2%, predominantly from chemotherapyendocrine therapy to endocrine treatment alone. Of 8 patients originally recommended chemotherapy, 25% were recommended endocrine treatment alone after receiving the Recurrence Score result. Conclusions. Though reimbursed by health insurances since January 2015, molecular tests are used moderately in our institution as per the decision of the multidisciplinary tumor board. It's mainly used to obtain a complementary confirmation supporting the decision of no chemotherapy. The OncotypeDx Recurrence Score results were in the intermediate group in 66% of the 9 tested cases but contributed to avoid chemotherapy in 2 patients during the last 12 months.

A unity power factor multiple isolated outputs switching mode power supply using a single switch

The authors present an offline switching power supply with multiple isolated outputs and unity power factor with the use of only one power processing stage, based on the DC-DC SEPIC (single ended primary inductance converter) modulated by variable hysteresis current control. The principle of operation, the theoretical analysis, the design procedure, an example, and simulation results are presented. A laboratory prototype, rated at 160 W, operating at a maximum switching frequency of 100 kHz, with isolated outputs rated at +5 V/15 A -5 V/1 A, +12 V/6 A and -12 V/1 A, has been built given an input power factor near unity.