Coupling coefficients of gratings with graded refractive index waveguides

In this paper, the effective coupling coefficient k(eff) and the self-coupling coefficient zeta(1) are introduced to describe the characteristic of gratings in a resonant situation when the effects of radiation and other partial waves coupling are considered. The dependence of these two coupling coefficients on grating tooth shapes and depths and the dimensions of graded refractive index (GRIN) waveguides is numerically analysed. The results show that the gratings with linear GRIN waveguides have the largest \k(eff)\. The possibility of realizing a complex-coupled DFB laser, even a pure gain or loss coupled DFB laser, employing only a real refractive index coupled grating is also discussed.

A Broadband Long-Wavelength Superluminescent Diode Based on Graded Composition Bulk InGaAs

A novel unselective regrowth buried heterostructure long-wavelength superluminescent diode （SLD） with a graded composition bulk InGaAs active region is developed by metalorganic vapor phase epitaxy （MOVPE）. At a 150mA injection current, the full width at half maximum of the emission spectrum of the SLD is about 72nm, ranging from 1602 to 1674nm. The emission spectrum is smooth and flat. The ripple of the spectrum is less than 0.3dB at any wavelength from 1550 to 1700nm. An output power of 4.3mW is obtained at a 200mA injection current under continuous-wave operation at room temperature. This device is suitable for the applications of light sources for gas detectors and L-band optical fiber communications.

Graded tensile-strained bulk InGaAs/InP superluminescent diode with very wide emission spectrum

A kind of novel broad-band superluminescent diodes (SLDs) using graded tensile-strained bulk InGaAs is developed. The graded tensile-strained bulk InGaAs is obtained by changing only group-III trimethyl-gallium source flow during low-pressure metal organic vapor-phase epitaxy. At the injection current of 200 mA, the fabricated SLDs with such structure demonstrate full-width at half-maximum spectral width of 106 nm and the output light power of 13.6 mW, respectively.

The main factor influencing the tensile properties of surface nano-crystallized graded materials

The improved mechanical properties of surface nano-crystallized graded materials produced by surface severe plastic deformation ((SPD)-P-2) are generally owing to the effects of the refined structure, work-hardened region and compressive residual stress. However, during the (SPD)-P-2 process, residual stress is produced simultaneously with work-hardened region, the individual contribution of these two factors to the improved mechanical properties remains unclear. Numerical simulations are carried out in order to answer this question. It is found that work hardening predominates in improving the yield strength and the ultimate tensile strength of the surface nano-crystallized graded materials, while the influence of the residual stress mainly emerges at the initial stage of deformation and decreases the apparent elastic modulus of the surface nano-crystallized graded materials, which agrees well with the experimental results. (C) 2010 Elsevier B.V. All rights reserved.

Nanoadhesion of a Power-Law Graded Elastic Material

The Dugdale-Barenblatt model is used to analyze the adhesion of graded elastic materials at the nanoscale with Young's modulus E varying with depth z according to a power law E = E-0(z/c(0))(k) (0 < k < 1) while Poisson's ratio v remains a constant, where E-0 is a referenced Young's modulus, k is the gradient exponent and c(0) is a characteristic length describing the variation rate of Young's modulus. We show that, when the size of a rigid punch becomes smaller than a critical length, the adhesive interface between the punch and the graded material detaches due to rupture with uniform stresses, rather than by crack propagation with stress concentration. The critical length can be reduced to the one for isotropic elastic materials only if the gradient exponent k vanishes.

Colloidal photonic crystals with a graded lattice-constant distribution

In this work, a gradient polystyrene colloidal photonic crystal was fabricated by annealing in a graded temperature field. The lattice constant of the gradient crystal gradually varied along the temperature-gradient direction. The positional bandgap wavelength as well as the attenuation of the bandgap wavelength could be tuned dependent on the position of the gradient colloidal crystal along the gradient direction because of the lattice-constant variation.

Modeling of organic light-emitting diodes with graded concentration in the emissive multilayer

We model the electrical behavior of organic light-emitting diodes whose emissive multilayer is formed by blends of an electron transporting material, tris-(8-hydroxyquinoline) aluminum (Alq(3)) and a hole transporting material, N,N-'-diphenyl-N,N-'-bis(1,1(')-biphenyl)-4,4-diamine. The multilayer is composed of layers of different concentration. The Alq(3) concentration gradually decreases from the cathode to the anode. We demonstrate that these graded devices have higher efficiency and operate at lower applied voltages than devices whose emissive layer is made of nominally homogeneous blends. Our results show an important advantage of graded devices, namely, the low values of the recombination rate distribution near the cathode and the anode, so that electrode quenching is expected to be significantly suppressed in these devices.

Optical intensity gradient by colloidal photonic crystals with a graded thickness distribution

Gradient colloidal crystals with a thickness gradient were prepared by the vertical deposition technique with vertically graded concentration suspensions. The thickness of the gradient colloidal crystal gradually changes at different positions along the specific gradient direction of the crystal. The thickness gradient was determined by the concentration gradient, depending on the initial colloidal concentration and the settling time. The optical transmission intensity at the dip wavelength can be tuned by changing the thickness of the colloidal crystals. The gradient colloidal crystals lead to a gradient of optical intensity at the dip in transmission light. The gradient of optical intensity at the dip increases as the thickness gradient of the colloidal crystal increases.

Improved efficiency by a graded emissive region in organic light-emitting diodes

Electrical and optical properties of organic light-emitting diodes (OLEDs) with a stepwise graded bipolar transport emissive layer for a better control of charge transport and recombination are presented. The graded bipolar transport layer was formed by co-evaporating a hole-transporting material N,N-'-diphenyl-N,N-'-bis(1,1(')-biphenyl)-4,4(')-diamine (NPB) and an electron-transporting/emissive material tris-(8-hydroxyquinoline) aluminum (Alq(3)) in steps, where each step has a different concentration ratio of NPB to Alq(3). Compared to a conventional heterojunction OLED, electroluminescence efficiency was enhanced by a factor of more than 1.5, whereas the turn-on voltage remained unchanged in the graded structure.

Controlling electric field distribution by graded spherical core-shell metamaterials

This paper investigates analytically the electric field distribution of graded spherical core-shell metamaterials, whose permittivity is given by the graded Drude model. Under the illumination of a uniform incident optical field, the obtained results show that the electrical field distribution in the shell region is controllable and the electric field peak's position inside the spherical shell can be confined in a desired position by varying the frequency of the optical field as well as the parameters of the graded dielectric profiles. It has also offered an intuitive explanation for controlling the local electric field by graded metamaterials.

Localization of the electric-field distribution in graded core-shell metamaterials

The local electric-field distribution has been investigated in a core-shell cylindrical metamaterial structure under the illumination of a uniform incident optical field. The structure consists of a homogeneous dielectric core, a shell of graded metal-dielectric metamaterial, embedded in a uniform matrix. In the quasistatic limit, the permittivity of the metamaterial is given by the graded Drude model. The local electric potentials and hence the electric fields have been derived exactly and analytically in terms of hypergeometric functions. Our results showed that the peak of the electric field inside the cylindrical shell can be confined in a desired position by varying the frequency of the optical field and the parameters of the graded profiles. Thus, by fabricating graded metamaterials, it is possible to control electric-field distribution spatially. We offer an intuitive explanation for the gradation-controlled electric-field distribution.

Dielectric response of graded spherical composites

We investigate the effective dielectric responses of graded spherical composites under an external uniform electric field by taking the dielectric function of spherical inclusion, epsilon(i) = cr(k) e(beta r), where r is the inner distance of a point inside the particle from the centre of the spherical particle in the coordination. In the dilute limit, our exact result is used to test the validity of differential effective dipole approximation (DEDA) for estimating the effective response of graded spherical composites and it is shown that the DEDA is in excellent agreement with the exact result.