Worldwide outdoor round robin study of organic photovoltaic devices and modules

Accurate characterization and reporting of organic photovoltaic (OPV) device performance remains one of the important challenges in the field. The large spread among the efficiencies of devices with the same structure reported by different groups is significantly caused by different procedures and equipment used during testing. The presented article addresses this issue by offering a new method of device testing using “suitcase sample” approach combined with outdoor testing that limits the diversity of the equipment, and a strict measurement protocol. A round robin outdoor characterization of roll-to-roll coated OPV cells and modules conducted among 46 laboratories worldwide is presented, where the samples and the testing equipment were integrated in a compact suitcase that served both as a sample transportation tool and as a holder and test equipment during testing. In addition, an internet based coordination was used via plasticphotovoltaics.org that allowed fast and efficient communication among participants and provided a controlled reporting format for the results that eased the analysis of the data. The reported deviations among the laboratories were limited to 5% when compared to the Si reference device integrated in the suitcase and were up to 8% when calculated using the local irradiance data. Therefore, this method offers a fast, cheap and efficient tool for sample sharing and testing that allows conducting outdoor measurements of OPV devices in a reproducible manner.

Young driver perceptions of police traffic enforcement and self reported driving offences

Purpose Road policing is a key method used to improve driver compliance with road laws. However, we have a very limited understanding of the perceptions of young drivers regarding police enforcement of road laws. This paper addresses this gap. Design/Methodology/Approach Within this study 238 young drivers from Queensland, Australia, aged 17-24 years (M = 18, SD = 1.54), with a provisional (intermediate) driver’s licence completed an online survey regarding their perceptions of police enforcement and their driver thrill seeking tendencies. This study considered whether these factors influenced self-reported transient (e.g., travelling speed) and fixed (e.g., blood alcohol concentration) road violations by the young drivers. Findings The results indicate that being detected by police for a traffic offence, and the frequency with which they display P-plates on their vehicle to indicate their licence status, are associated with both self-reported transient and fixed rule violations. Licence type, police avoidance behaviours and driver thrill seeking affected transient rule violations only, while perceptions of police enforcement affected fixed rule violations only. Practical implications This study suggests that police enforcement of young driver violations of traffic laws may not be as effective as expected and that we need to improve the way in which police enforce road laws for young novice drivers. Originality/value: This paper identifies that perceptions of police enforcement by young drivers does not influence all types of road offences.

Arrested Drunk Drivers : Trends, social background, recidivism and mortality

The aim of this study was to examine the trends, incidence and recidivism of drunken driving during a 20-year period (1988 - 2007) using the data on all suspected drunken driving in this period. Furthermore, the association between social background and drunken driving, and the mortality of drunk drivers were studied by using administrative register data provided by Statistics Finland. The study was completely register-based. In 1989 - 1991, every year 30,000 drivers were suspected of drunken driving, but the number fell to less than 20,000 by 1994, during the economic recession. The changes in the arrest incidence of the youngest age groups were especially pronounced, most of all in the age group of 18 - 19-year olds. Even though the incidence among youth decreased dramatically, their incidence rate was still twice that of the general population aged 15 - 84 years. Drunken driving was associated with a poor social background among youth and working-aged men and women. For example, a low level of education, unemployment, divorce, and parental factors in youth were associated with a higher risk of being arrested for drunken driving. While a low income was related to more drunken driving among working-aged people, the effect among young persons was the opposite. Every third drunk driver got rearrested during a 15-year period, whereas the estimated rearrest rate was 44%. Findings of drugs only or in combination with alcohol increased the risk of rearrest. The highest rearrest rates were seen among drivers who were under the influence of amphetamines or cannabis. Also male gender, young age, high blood alcohol concentration, and arrest during weekdays and in the daytime predicted rearrest. When compared to the general population, arrested drunk drivers had significant excess mortality. The greatest relative differences were seen in alcohol-related causes of death (including alcohol diseases and alcohol poisoning), accidents, suicides and violence. Also mortality due to other than alcohol-related diseases was elevated among drunk drivers. Drunken driving was associated with multiple factors linked to traffic safety, health and social problems. Social marginalization may expose a person to harmful use of alcohol and drunken driving, and the associations are seen already among the youth. Recidivism is common among drunk drivers, and driving under the influence of illicit and/or medicinal drugs is likely to indicate worse substance abuse problems, judging from the high rearrest rates. High alcohol-related mortality in this population shows that drunken driving is clearly an indicator of alcohol abuse. More effective measures of preventing alcohol-related harms are needed, than merely preventing convicted drunk drivers from driving again.

Interfaz Gráfica para la Automatización y Gestión de Escenarios Experimentales (IGAGEE).

[ES]El sistema IGAGEE proporciona una solución integrada para facilitar la automatización de pruebas y la gestión de equipamiento y resultados en entornos experimentales de laboratorio. En este tipo de escenarios es necesario controlar elementos diversos de forma coordinada y manejar información compleja de configuración y resultados. El sistema IGAGEE permite: (a) resolver de forma adecuada la integración de las herramientas disponibles, (b) solucionar la organización de las configuraciones y resultados, (c) ofrecer una interfaz única a los usuarios para la gestión y visualización de datos y (d) resolver la gestión remota del equipamiento de pruebas. Se ha diseñado el sistema IGAGEE buscando soluciones generales aplicables a entornos diferentes. Para la validación de las propuestas de diseño se ha desarrollado un prototipo inicial atendiendo a las necesidades concretas del grupo de investigación NQaS en su línea de investigación sobre Análisis y Monitorización de Tráfico en red.

Avaliação da função endotelial em mulheres jovens portadoras da síndrome dos ovários policísticos

A síndrome dos ovários policísticos é uma desordem frequente e complexa, com grande variabilidade fenotípica, predominando os sinais de disfunção ovariana. Alterações metabólicas, inflamatórias e vasculares vinculadas à resistência à insulina são muito prevalentes nessa desordem podendo manifestar-se precocemente. O objetivo principal deste estudo foi investigar a presença de alterações microvasculares em mulheres jovens e não obesas portadoras da síndrome dos ovários policísticos, através de videocapilaroscopia periungueal e dosagem dos níveis séricos de endotelina-1. O objetivo secundário foi verificar a existência de associações entre os achados vasculares, níveis séricos de androgênios, parâmetros clínicos, bioquímicos, metabólicos e inflamatórios relacionados ao risco cardiovascular. Em estudo observacional, transverso e controlado avaliamos 12 mulheres com diagnóstico de síndrome dos ovários policísticos, segundo os critérios estabelecidos pelo consenso de Rotterdam e nove voluntárias saudáveis. A idade (22,82,3 X 24,62,7), o índice de massa corporal (22,53,4 X 23,73,1) e a circunferência da cintura (7510,1 X 77,38,1) foram semelhantes nos dois grupos. As portadoras da síndrome apresentavam hiperandrogenismo clínico. Não foram observadas diferenças significativas entre os grupos quando analisados os níveis séricos de estradiol, testosterona total, androstenediona ou o índice de testosterona livre, entretanto a SHBG mostrou-se significativamente mais baixa no grupo de estudo (p=0,011). A glicemia de jejum, insulina, HOMA-IR e o perfil lipídico foram normais e sem diferença entre os grupos. A amostra com síndrome dos ovários policísticos não apresentava intolerância à glicose ou Diabetes Mellitus pelo teste oral de tolerância à glicose. Os níveis séricos dos marcadores inflamatórios (leucócitos, ácido úrico, adiponectina, leptina e proteína c reativa) e do marcador de função endotelial avaliado também foram similares nos dois grupos. A velocidade de deslocamento das hemácias no basal e após oclusão foram significativamente menores nas pacientes de estudo (p=0,02), mas o tempo para atingir a VDHmax e os parâmetros relativos à morfologia e densidade capilar foram semelhantes. Não observamos correlação entre a velocidade de deslocamento das hemácias e níveis plasmáticos de endotelina-1, androgênios ou parâmetros de resistência insulínica. A velocidade de deslocamento das hemácias associou-se positivamente aos níveis plasmáticos de estradiol (r= 0,45, p<0,05) e negativamente aos de colesterol total e LDL colesterol (r= -0,52, p<0,05; r=-0,47, p<0,05, respectivamente). Em conclusão nossos resultados fornecem evidência adicional de dano precoce à função microvascular em mulheres portadoras de síndrome dos ovários policísticos. Através da capilaroscopia periungueal dinâmica, demonstramos que mulheres jovens com moderado hiperandrogenismo, sem obesidade, RI, hipertensão ou dislipidemia, já apresentam disfunção microvascular nutritiva, caracterizada por redução na velocidade de fluxo das hemácias no basal e após oclusão. Estes achados micro-circulatórios não foram acompanhados de elevações nos níveis plasmáticos de endotelina-1.

土石混合体细观结构力学及其边坡稳定性研究

Soil-rock mixture (S-RM) refers to one extremely uneven loose rock and soil materials system with certain stone content. Its formation has started since Quaternary and it is composed of block stone, fine grained soil and pore with certain project scale and high strength. S-RM has extensive distribution in nature, especially in southwest China where the geotectonic background is complicated, the fracture activity is developed and the geomorphological characteristics of high mountain and steep gorge area are protuberant. This kind of complicated geologic body has developed wider in these areas. S-RM has obvious difference with the general soil or rock (rock mass) in physical and mechanical properties because its two components-“soil” and “rock-block” has extreme differences in physical and mechanical properties. The proposition of S-RM and its deep research are needed in the modern engineering construction. It is also the necessity in the modern development of rock and soil mechanics. The dissertation starts from the meso-structural characteristics of soil-rock and takes a systematic research on its meso-structural mechanics, deformation and failure mechanism and the stability of S-RM slope. In summary, it achieves the following innovative results and conclusions. There are various views on the conception of S-RM and its classification system. Based on the large number of field tests, the dissertation makes the conception and classification of S-RM more systematic. It systematically proposed the conception of meso-structural mechanics of S-RM. Thus the dissertation has laid a foundation for its deep study. With the fast development of the computer technology and digital image processing theory, digital image processing technology has been successfully applied in many fields and provided reliable technology support for the quantitative description of the structural characteristics of S-RM. Based on the digital image processing technology, the dissertation systematically proposes and developed the quantitative analysis method and quantitative index for the meso-structure of S-RM. The results indicate that the meso-structure such as its internal soil-rock granularity composition, the soil-rock shape and the orientability has obvious self-organization in the macro statistical level. The dissertation makes a systematic research on the physical mechanical properties, deformation and failure mechanism of S-RM based on large field test. It proposes the field test for the underwater S-RM and deduces the 3D data analysis method of in-situ horizontal push-shear test. The result indicates that S-RM has significant phenomenon of shear dilatancy in the shearing process, and its dilatancy will be more obvious with the increased proportion of rock or the decreased confining pressure. The proportion of rock has great effect on the strength of S-RM and rock-block, especially the spatial position of particles with comparatively big size has great effect on the shape and spatial position of the sample shear zone. The dissertation makes some improvements in the single ring infiltration test equipment and its application on the permeability of S-RM. The results indicate that the increasing of rock-block would make it more difficult for the soil to fill in the vacuity between the rock-block and the proportion would increase which would result in the increased permeability coefficient. The dissertation builds the real meso-structural model of S-RM based on the digital image processing technology. By using geometric reconstruction technology, it transfers the structural mode represented by Binary image into CAD format, which makes it possible to introduce the present finite element analysis software to take research on numerical experimental investigation. It systematically realizes leaping research from the image，geometric mode, to meso-structural mechanics numerical experiment. By using this method, the dissertation takes large scale numerical direct-shear test on the section of S-RM. From the mesoscopic perspective, it reveals three extended modes about the shear failure plane of S-RM. Based on the real meso-structural model and by using the numerical simulation test, the character and mechanics of seepage failure of S-RM are studied. At the same time, it builds the real structural mode of the slope based on the analysis about the slope crosssection of S-RM. By using the strength reduction method, it takes the research on the stability of S-RM and gets great achievements. The three dimensional geometric reconstruction technology of rock block is proposed, which provides technical support for the reconstruction of the 3D meso-structural model of S-RM. For the first time, the dissertation builds the stochastic structure model of two-dimensional and three-dimensional polygons or polyhedron based on the stochastic simulation technique of monte carlo method. It breaks the traditional research which restricted to the random generation method of regular polygon and develops the relevant software system (R-SRM2D/3D) which has great effect on meso-structural mechanics of S-RM. Based on the R-SRM software system which randomly generates the meso-structural mode of S-RM according to the different meso-structural characteristics, the dissertation takes a series of research on numerical test of dual axis and real three-axis, systematically analyses the meso destroy system, the effects of meso-structural characteristics such as on the stone content, size composition and block directionality on the macro mechanical behavior and macro-permeability. Then it proposes the expression of the upper and lower limit for the macro-permeability coefficient of the inhomogeneous geomaterials, such as S-RM. By using the strength reduction FEM, the dissertation takes the research on the stability of the slope structural mode of the randomly formed S-RM. The results indicate that generally, the stability coefficient of S-RM slope increases with the increasing of stone content; on the condition of the same stone content, the stability coefficient of slope will be different with different size composition and the space position of large block at the internal slop has great effect on the stability. It suggests that meso-structural characteristics, especially the space position of large block should be considered when analyzing the stability of this kind of slope and strengthening design. Taking Xiazanri S-RM slope as an example, the dissertation proposes the fine modeling of complicated geologic body based on reverse engineering and the generation method of FLAC3D mode. It resolves the bottleneck problem about building the fine structural mode of three-dimensional geological body. By using FLAC3D, the dissertation takes research on the seepage field and the displacement field of Xiazanri S-RM slope in the process of reservoir water level rising and decreasing. By using strength reduction method, it analyses the three-dimension stability in the process of reservoir water level rising and decreasing. The results indicate that the slope stability firstly show downward trend in the process of reservoir water level rising and then rebound to increase; the sudden drawdown of reservoir water level has great effect on the slope stability and this effect will increase with the sudden drawdown amplitude rising. Based on the result of the rock block size analysis of S-RM, and using R-SRM2D the stochastic structure model of Xiazanri S-RM slope is built. By using strength reduction method, the stability of the stochastic structure model is analysis, the results shows that the stability factor increases significantly after considering the block.

The impact of powder flowing properties on dosator filling system operation

Purpose: To study the impact of powder flow properties on dosator filling systems, with particular focus on improvements in dose weight accuracy and repeatability. Method: This study evaluates a range of critical powder flow properties such as: flow function, cohesion, wall friction, adhesion to wall surfaces, density/compressibility data, stress ratio “K” and gas permeability. The characterisations of the powders considered in this study were undertaken using an annular shear cell using a sample size of 0.5 litres. This tester also incorporated the facility to measure bed expansion during shear in addition to contraction under consolidation forces. A modified Jenike type linear wall friction tester was used to develop the failure loci for the powder sample in conjunction with multiple wall samples (representing a variety of material types and surface finishes). Measurements of the ratio of applied normal stress versus lateral stress were determined using a piece of test equipment specifically designed for the purpose. Results: The correct characterisation of powders and the incorporation of this data into the design of process equipment are recognised as critical for reliable and accurate operation. An example of one aspect of this work is the stress ratio “K”. This characteristic is not well understood or correctly interpreted in many cases – despite its importance. Fig 1 [Omitted] (illustrates a sample of test data. The slope of the line gives the stress ratio in a uniaxial compaction system – indicating the behaviour of the material under compaction during dosing processes. Conclusions: A correct assessment of the bulk powder properties for a given formulation can allow prediction of: cavity filling behaviour (and hence dosage), efficiency of release from dosator, and strength and stability of extruded dose en route to capsule filling Influences over the effectiveness of dosator systems have been shown to be impacted upon by: bed pre-compaction history, gas permeability in the bed (with respect to local density effects), and friction effects for materials of construction for dosators

Laser Doppler velocimetry measurements of particle velocity profiles in gas-solid two-phase flows

The measurement of particle velocities in two-phase gas-solid systems has a wide application in flow monitoring in process plant, where two-phase gas-solids systems are frequently employed in the form of pneumatic conveyors and solid fuel injection systems. Such measurements have proved to be difficult to make reliably in industrial environments. This paper details particle velocity measurements made in a two phase gas-solid now utilising a laser Doppler velocimetry system. Tests were carried out using both wheat flour and pulverised coal as the solids phase, with air being used as the gaseous phase throughout. A pipeline of circular section, having a diameter of 53 mm was used for the test work, with air velocities ranging from 25 to 45 m/s and suspension densities ranging from 0.001 kg to 1 kg of solids per cubic meter of air. Details of both the test equipment used, and the results of the measurements are presented.

A compreensão dos alunos do 6.º ano de analogias presentes em vídeos didáticos sobre o corpo humano

Relatório Final apresentado à Escola Superior de Educação de Lisboa para obtenção de grau de mestre no Mestrado em Ensino do 1.º e 2.º Ciclo do Ensino Básico

Methylation profile of TP53 regulatory pathway and mtDNA alterations in breast cancer patients lacking TP53 mutations.

The present study investigated promoter hypermethylation of TP53 regulatory pathways providing a potential link between epigenetic changes and mitochondrial DNA (mtDNA) alterations in breast cancer patients lacking a TP53 mutation. The possibility of using the cancer-specific alterations in serum samples as a blood-based test was also explored. Triple-matched samples (cancerous tissues, matched adjacent normal tissues and serum samples) from breast cancer patients were screened for TP53 mutations, and the promoter methylation profile of P14(ARF), MDM2, TP53 and PTEN genes was analyzed as well as mtDNA alterations, including D-loop mutations and mtDNA content. In the studied cohort, no mutation was found in TP53 (DNA-binding domain). Comparison of P14(ARF) and PTEN methylation patterns showed significant hypermethylation levels in tumor tissues (P < 0.05 and <0.01, respectively) whereas the TP53 tumor suppressor gene was not hypermethylated (P < 0.511). The proportion of PTEN methylation was significantly higher in serum than in the normal tissues and it has a significant correlation to tumor tissues (P < 0.05). mtDNA analysis revealed 36.36% somatic and 90.91% germline mutations in the D-loop region and also significant mtDNA depletion in tumor tissues (P < 0.01). In addition, the mtDNA content in matched serum was significantly lower than in the normal tissues (P < 0.05). These data can provide an insight into the management of a therapeutic approach based on the reversal of epigenetic silencing of the crucial genes involved in regulatory pathways of the tumor suppressor TP53. Additionally, release of significant aberrant methylated PTEN in matched serum samples might represent a promising biomarker for breast cancer.

Accelerated aging of thick glass second surface silvered reflectors under sandstorm conditions

Concentrated solar power systems are expected to be sited in desert locations where the direct normal irradiation is above 1800 kWh/m2.year. These systems include large solar collector assemblies, which account for a significant share of the investment cost. Solarreflectors are the main components of these solar collector assemblies and dust/sand storms may affect their reflectance properties, either by soiling or by surface abrasion. While soiling can be reverted by cleaning, surface abrasion is a non reversible degradation.The aim of this project was to study the accelerated aging of second surface silvered thickglass solar reflectors under simulated sandstorm conditions and develop a multi-parametric model which relates the specular reflectance loss to dust/sand storm parameters: wind velocity, dust concentration and time of exposure. This project focused on the degradation caused by surface abrasion.Sandstorm conditions were simulated in a prototype environmental test chamber. Material samples (6cm x 6cm) were exposed to Arizona coarse test dust. The dust stream impactedthese material samples at a perpendicular angle. Both wind velocity and dust concentrationwere maintained at a stable level for each accelerated aging test. The total exposure time in the test chamber was limited to 1 hour. Each accelerated aging test was interrupted every 4 minutes to measure the specular reflectance of the material sample after cleaning.The accelerated aging test campaign had to be aborted prematurely due to a contamination of the dust concentration sensor. A robust multi-parametric degradation model could thus not be derived. The experimental data showed that the specular reflectance loss decreasedeither linearly or exponentially with exposure time, so that a degradation rate could be defined as a single modeling parameter. A correlation should be derived to relate this degradation rate to control parameters such as wind velocity and dust/sand concentration.The sandstorm chamber design would have to be updated before performing further accelerated aging test campaigns. The design upgrade should improve both the reliability of the test equipment and the repeatability of accelerated aging tests. An outdoor exposure test campaign should be launched in deserts to learn more about the intensity, frequencyand duration of dust/sand storms. This campaign would also serve to correlate the results of outdoor exposure tests with accelerated exposure tests in order to develop a robust service lifetime prediction model for different types of solar reflector materials.

Predictive models for chronic renal disease using decision trees, naïve bayes and case-based methods

Data mining can be used in healthcare industry to “mine” clinical data to discover hidden information for intelligent and affective decision making. Discovery of hidden patterns and relationships often goes intact, yet advanced data mining techniques can be helpful as remedy to this scenario. This thesis mainly deals with Intelligent Prediction of Chronic Renal Disease (IPCRD). Data covers blood, urine test, and external symptoms applied to predict chronic renal disease. Data from the database is initially transformed to Weka (3.6) and Chi-Square method is used for features section. After normalizing data, three classifiers were applied and efficiency of output is evaluated. Mainly, three classifiers are analyzed: Decision Tree, Naïve Bayes, K-Nearest Neighbour algorithm. Results show that each technique has its unique strength in realizing the objectives of the defined mining goals. Efficiency of Decision Tree and KNN was almost same but Naïve Bayes proved a comparative edge over others. Further sensitivity and specificity tests are used as statistical measures to examine the performance of a binary classification. Sensitivity (also called recall rate in some fields) measures the proportion of actual positives which are correctly identified while Specificity measures the proportion of negatives which are correctly identified. CRISP-DM methodology is applied to build the mining models. It consists of six major phases: business understanding, data understanding, data preparation, modeling, evaluation, and deployment.

Alcoolemia em vítimas fatais de acidentes de trânsito no Rio Grande do Norte empregando cromatografia em fase gasosa - head space

Alcohol is one of the few psychotropic drugs that their consumption has admitted legally and sometimes encouraged by the society. Studies show alcohol as the highest consumption of drugs among young people and society in general, probably because of its availability and easy access. The abuse causes public health problems, which was closely related to the violence, socioeconomic problems and the high number of automobile accidents. Transit is one of the main sectors affected by the effects of alcohol, observing a high incidence in the studies. About half of automobile accidents occurs after the consumption of alcoholic beverage, and the vast majority of cases related to high concentrations of alcohol in the bloodstream. The relationship of drunk with traffic accidents is in fact evident everywhere in the world, including Brazil, where studies have shown a high relationship between alcohol consumption and traffic accidents. This study determined the alcohol in fatal victims of traffic accidents in the state of Rio Grande do Norte and established the profile of this population compared with those found in Brazil and other countries. Samples of blood of ethanol added to fulfillment of the standardization of chromatographic conditions and procedures for the analysis, being employed in the determination of alcohol in blood samples of 277 victims of traffic accidents, collected at the Institute of Scientific Technical Police of Rio Grande do North (ITEP) in the year 2007. The blood alcohol level was determined in these samples correlated with the sex, age and marital status of the victim and the location, day of week and month when the accident occurred, is doing a statistical analysis and outlining a profile of the victims of an accident at transit in the state of Rio Grande do Norte. The parameters of standardization studied ensured the quality of the analytical method and, consequently, to obtain reliable laboratory results. Being given the best temperature for injector (150 ºC), detector (250 ºC) and column (50 ºC) with a flow of gas in the column of 2mL/minutos and analysis of time of 12 minutes. The method was linear in the range of 0.01 to 3.2 g / L (r2 = 0.9989) with average recovery of 100.2% and precision with coefficient of variation less than 15%. The analysis carried out on victims of fatal road traffic accidents, ethanol detected in the blood in 66.43% of the victims and these, 96% showed concentration ≥ 0.2 g / L, 87.73% of victims were male, while 12.27% female. The younger age group (1535 years) was the most involved (52,35%) and most single (55.60%). The accidents occurred with greater prevalence in the day on Monday (27%) followed by Sunday (24,19%) and Saturday (15,52%) and it was found that the prevalence of injuries varied between the different months of the year, and in February (14.4%) and April (10.47%) the months that had a higher number of accidents, however this oscillation showed no statistically significant difference. Also no significant difference was observed between the tracks of concentration found in men and women. The standardized method showed to be efficient, given satisfactorily to the goals of this work, and the high levels of alcohol found in victims of fatal road traffic accidents are consistent with several studies of literature, and the profile of the victim also supported by presenting in its most young adults, male and single

Shear strength evaluation of composite-composite resin associations

Objective: The aim of this study was to investigate the shear strength between distinct associations of different commercial composite resins and their fracture modes.Methods: Nine composite-composite associations (n = 90) were prepared for shear strength evaluation and separated into the following groups: Z/Z (Filtek Z250 UD + Filtek Z250 A2); Z/ D (Filtek Z250 UD + Durafill VS A2); Z/S (Filtek Z250 UD + Filtek Supreme YT); C/C (Charisma OA2 + Charisma A2); C/D (Charisma OA2 + Durafill VS A2); C/S (Charisma OA2 + Filtek Supreme YT); H/H (Herculite XRV B2D + Herculite XRV B2E); H/D (Herculite XRV B2D + Durafill VS A2); H/S (Herculite XRV B2D + Filtek Supreme YT). Shear tests were carried out using universal mechanical test equipment with a load of 200 kgf and speed of 0.5 mm/min. Ultimate shear strength data (MPa) from all tested groups were submitted to analysis of variance (one-way ANOVA) and the Tukey test. The fractured surfaces of the test samples were visually evaluated by binocular stereomicroscope at 20 times magnification. Fractures were classified as either adhesive or cohesive or mixed.Results: The highest ultimate shear strength observed for composite-composite associations was found for the groups: Z/Z, C/S, H/H, H/S, Z/S and C/C. Those associations containing the Durafill resin were weaker than the others.Conclusion: Microparticle RBC associations presented lower shear strength than hybrid and/or nanoparticle RBC associations, once the only significant difference was found when the Durafill resin was involved. (c) 2008 Elsevier Ltd. All rights reserved.

Fatigue apparatus for geometrically complex non-standardized specimens

Standard Test Methods (e.g. ASTM, DIN) for materials characterization in general, and for fatigue in particular, do not contemplate specimens with complex geometries, as well as the combination of axial and in-plane bending loads in their methodologies. The present study refers to some patents and the new configuration or configurations of specimens (non-standardized by the status quo of test methods) and a device developed to induce axial and bending combined forces resultants from axial loads applied by any one test equipment (dynamic or monotonic) which possesses such limitation, towards obtaining more realistic results on the fatigue behavior, or even basic mechanical properties, from geometrically complex structures. Motivated by a specific and geometrically complex aeronautic structure (motor-cradle), non-standardized welded tubular specimens made from AISI 4130 steel were fatigue-tested at room temperature, by using a constant amplitude sinusoidal load of 20 Hz frequency, load ratio R = 0.1 with and without the above referred auxiliary fatigue apparatus. The results showed the fatigue apparatus was efficient for introducing higher stress concentration factor at the welded specimen joints, consequently reducing the fatigue strength when compared to other conditions. From the obtained results it is possible to infer that with small modifications the proposed apparatus will be capable to test a great variety of specimen configurations such as: squared tubes and plates with welded or melted junctions, as well as other materials such as aluminum, titanium, composites, polymeric, plastics, etc. © 2009 Bentham Science Publishers Ltd.