A self-timed multipurpose delay sensor for field programmable gate arrays (FPGAs)

This paper presents a novel self-timed multi-purpose sensor especially conceived for Field Programmable Gate Arrays (FPGAs). The aim of the sensor is to measure performance variations during the life-cycle of the device, such as process variability, critical path timing and temperature variations. The proposed topology, through the use of both combinational and sequential FPGA elements, amplifies the time of a signal traversing a delay chain to produce a pulse whose width is the sensor’s measurement. The sensor is fully self-timed, avoiding the need for clock distribution networks and eliminating the limitations imposed by the system clock. One single off- or on-chip time-to-digital converter is able to perform digitization of several sensors in a single operation. These features allow for a simplified approach for designers wanting to intertwine a multi-purpose sensor network with their application logic. Employed as a temperature sensor, it has been measured to have an error of ±0.67 °C, over the range of 20–100 °C, employing 20 logic elements with a 2-point calibration.

System-on-chip field-programmable gate array design for onboard real-time hyperspectral unmixing

Hyperspectral instruments have been incorporated in satellite missions, providing large amounts of data of high spectral resolution of the Earth surface. This data can be used in remote sensing applications that often require a real-time or near-real-time response. To avoid delays between hyperspectral image acquisition and its interpretation, the last usually done on a ground station, onboard systems have emerged to process data, reducing the volume of information to transfer from the satellite to the ground station. For this purpose, compact reconfigurable hardware modules, such as field-programmable gate arrays (FPGAs), are widely used. This paper proposes an FPGA-based architecture for hyperspectral unmixing. This method based on the vertex component analysis (VCA) and it works without a dimensionality reduction preprocessing step. The architecture has been designed for a low-cost Xilinx Zynq board with a Zynq-7020 system-on-chip FPGA-based on the Artix-7 FPGA programmable logic and tested using real hyperspectral data. Experimental results indicate that the proposed implementation can achieve real-time processing, while maintaining the methods accuracy, which indicate the potential of the proposed platform to implement high-performance, low-cost embedded systems, opening perspectives for onboard hyperspectral image processing.

Teste da rede de interconexões de field programmable analog arrays

Os dispositivos analógicos programáveis (FPAAs, do inglês, Field Programmable Analog Arrays), apesar de ainda não terem a mesma popularidade de seus pares digitais (FPGAs, do inglês, Field Programmable Gate Arrays), possuem uma gama de aplicações bastante ampla, que vai desde o condicionamento de sinais em sistemas de instrumentação, até o processamento de sinais de radiofreqüência (RF) em telecomunicações. Porém, ao mesmo tempo em que os FPAAs trouxeram um impressionante ganho na agilidade de concepção de circuitos analógicos, também trouxeram um conjunto de novos problemas relativos ao teste deste tipo de dispositivo. Os FPAAs podem ser divididos em duas partes fundamentais: seus blocos programáveis básicos (CABs, do inglês, Configurable Analog Blocks) e sua rede de interconexões. A rede de interconexões, por sua vez, pode ser dividida em duas partes: interconexões internas (locais e globais entre CABs) e interconexões externas (envolvendo células de I/O). Todas estas partes apresentam características estruturais e funcionais distintas, de forma que devem ser testadas separadamente, pois necessitam que se considerem modelos de falhas, configurações e estímulos de teste específicos para assegurar uma boa taxa de detecção de defeitos. Como trabalhos anteriores já estudaram o teste dos CABs, o foco desta dissertação está direcionado ao desenvolvimento de metodologias que se propõem a testar a rede de interconexões de FPAAs. Apesar das várias diferenças entre as redes de interconexões de FPGAs e FPAAs, muitas também são as semelhanças entre elas, sendo, portanto, indiscutível que o ponto de partida deste trabalho tenha que ser o estudo das muitas técnicas propostas para o teste de interconexões em FPGAs, para posterior adaptação ao caso dos FPAAs. Além disto, embora o seu foco não recaia sobre o teste de CABs, pretende-se utilizá-los como recursos internos do dispositivo passíveis de gerar sinais e analisar respostas de teste, propondo uma abordagem de auto-teste integrado de interconexões que reduza o custo relativo ao equipamento externo de teste. Eventualmente, estes mesmos recursos poderão também ser utilizados para diagnóstico das partes defeituosas. Neste trabalho, utiliza-se como veículo de experimentação um dispositivo específico (Anadigm AN10E40), mas pretende-se que as metodologias de teste propostas sejam abrangentes e possam ser facilmente adaptadas a outros FPAAs comerciais que apresentem redes de interconexão semelhantes.

Pré-regulador retificador boost com controle digital por valores médios, para sistema de iluminação fluorescente multi-lâmpadas, utilizando dispositivo FPGA e VHDL

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Contribuição para o estudo do embarque de uma rede neural artificial em field programmable gate array (FPGA)

This study shows the implementation and the embedding of an Artificial Neural Network (ANN) in hardware, or in a programmable device, as a field programmable gate array (FPGA). This work allowed the exploration of different implementations, described in VHDL, of multilayer perceptrons ANN. Due to the parallelism inherent to ANNs, there are disadvantages in software implementations due to the sequential nature of the Von Neumann architectures. As an alternative to this problem, there is a hardware implementation that allows to exploit all the parallelism implicit in this model. Currently, there is an increase in use of FPGAs as a platform to implement neural networks in hardware, exploiting the high processing power, low cost, ease of programming and ability to reconfigure the circuit, allowing the network to adapt to different applications. Given this context, the aim is to develop arrays of neural networks in hardware, a flexible architecture, in which it is possible to add or remove neurons, and mainly, modify the network topology, in order to enable a modular network of fixed-point arithmetic in a FPGA. Five synthesis of VHDL descriptions were produced: two for the neuron with one or two entrances, and three different architectures of ANN. The descriptions of the used architectures became very modular, easily allowing the increase or decrease of the number of neurons. As a result, some complete neural networks were implemented in FPGA, in fixed-point arithmetic, with a high-capacity parallel processing

Geração automática de controladores em FPGA integrando animação gráfica

Dissertação apresentada na Faculdade de Ciências e Tecnologia da Universidade Nova de Lisboa para obtenção do grau de Mestre em Engenharia Electrotécnica e de Computadores

Field-Programmable Gate Array Card for Readout and Control of Cryoelectronics

The main goal of the present Master’s Thesis project was to create a field-programmable gate array (FPGA) based system for the control of single-electron transistors or other cryoelectronic devices. The FPGA and similar technologies are studied in the present work. The fixed and programmable logic are compared with each other. The main features and limitations of the hardware used in the project are investigated. The hardware and software connections of the device to the computer are shown in detail. The software development techniques for FPGA-based design are described. The steps of design for programmable logic are considered. Furthermore, the results of filters implemented in the software are illustrated.

Field programmable gate array based target detection and gesture recognition

The move from Standard Definition (SD) to High Definition (HD) represents a six times increases in data, which needs to be processed. With expanding resolutions and evolving compression, there is a need for high performance with flexible architectures to allow for quick upgrade ability. The technology advances in image display resolutions, advanced compression techniques, and video intelligence. Software implementation of these systems can attain accuracy with tradeoffs among processing performance (to achieve specified frame rates, working on large image data sets), power and cost constraints. There is a need for new architectures to be in pace with the fast innovations in video and imaging. It contains dedicated hardware implementation of the pixel and frame rate processes on Field Programmable Gate Array (FPGA) to achieve the real-time performance. ^ The following outlines the contributions of the dissertation. (1) We develop a target detection system by applying a novel running average mean threshold (RAMT) approach to globalize the threshold required for background subtraction. This approach adapts the threshold automatically to different environments (indoor and outdoor) and different targets (humans and vehicles). For low power consumption and better performance, we design the complete system on FPGA. (2) We introduce a safe distance factor and develop an algorithm for occlusion occurrence detection during target tracking. A novel mean-threshold is calculated by motion-position analysis. (3) A new strategy for gesture recognition is developed using Combinational Neural Networks (CNN) based on a tree structure. Analysis of the method is done on American Sign Language (ASL) gestures. We introduce novel point of interests approach to reduce the feature vector size and gradient threshold approach for accurate classification. (4) We design a gesture recognition system using a hardware/ software co-simulation neural network for high speed and low memory storage requirements provided by the FPGA. We develop an innovative maximum distant algorithm which uses only 0.39% of the image as the feature vector to train and test the system design. Database set gestures involved in different applications may vary. Therefore, it is highly essential to keep the feature vector as low as possible while maintaining the same accuracy and performance^

FPGA field oriented control of an axial flux motor-in-wheel

This paper presents the design and the prototype implementation of a three-phase power inverter developed to drive a motor-in-wheel. The control system is implemented in a FPGA (Field Programmable Gate Array) device. The paper describes the Field Oriented Control (FOC) algorithm and the Space Vector Modulation (SVM) technique that were implemented. The control platform uses a Spartan-3E FPGA board, programmed with Verilog language. Simulation and experimental results are presented to validate the developed system operation under different load conditions. Finally are presented conclusions based on the experimental results.

Implementação em FPGA de um Modem QPSK

Esta dissertação insere-se num conjunto de trabalhos a decorrer no Instituto de Telecomunicações de Aveiro que tem como objetivo o desenvolvimento de um sistema de comunicação para um UAV. Neste sentido, apresenta a implementação e validação de um modem em banda base aberto e flexível implementado em FPGA, baseado em abordagem SDR, com possibilidade de integraçãoo no sistema de comunicação com o UAV. Ao longo desta dissertação implementou-se, utilizando o MATLAB, um modem de modulação adaptável, ao qual foram integrados algoritmos de sincronismo e de correção de fase. Desta forma, foi possível realizar uma análise ao modelo comportamental dos vários constituintes do modem abstraindose dos tempos de atraso do processamento ou da precisão da representação dos dados, e assim simplificar a sua implementação em hardware. Analisado o modelo comportamental do modem desenvolvido em MATLAB realizou-se a sua implementação em hardware para a modulação QPSK. A sua prototipagem foi realizada, com recurso à ferramenta computacional Vivado Design Suite 2014.2, utilizando o kit de desenvolvimento ZedBoard e o frontend AD-FMCOMMS1-EBZ. O correto funcionamento dos módulos implementados em hardware foi posteriormente avaliado através de uma interface entre o MATLAB e a Zed- Board, sendo que, os resultados obtidos no modelo em MATLAB serviram como termo de comparação. Através da utilização desta interface é possível validar parte do modem implementado em FPGA, mantendo o restante processamento a ser realizado em MATLAB, validando assim os módulos em FPGA de uma forma isolada.

Hybrid three-phase HPF rectifier with programmable input current THD, using FPGA device and VHDL language

In this paper is proposed and analyzed a digital hysteresis modulation using a FPGA (Field Programmable Gate Array) device and VHDL (Hardware Description Language), applied at a hybrid three-phase rectifier with almost unitary input power factor, composed by parallel SEPIC controlled single-phase rectifiers connected to each leg of a standard 6-pulses uncontrolled diode rectifier. The digital control allows a programmable THD (Total Harmonic Distortion) at the input currents, and it makes possible that the power rating of the switching-mode converters, connected in parallel, can be a small fraction of the total average output power, in order to obtain a compact converter, reduced input current THD and almost unitary input power factor. Finally, the proposed digital control, using a FPGA device and VHDL, offers an important flexibility for the associated control technique, in order to obtain a programmable PFC (Power Factor Correction) hybrid three-phase rectifier, in agreement with the international standards (IEC, and IEEE), which impose limits for the THD of the AC (Alternate Current) line input currents. The proposed strategy is verified by experiments. © 2008 IEEE.

Implementação em FPGA de módulo de efeito de reverberação

Reverberation is caused by the reflection of the sound in adjacent surfaces close to the sound source during its propagation to the listener. The impulsive response of an environment represents its reverberation characteristics. Being dependent on the environment, reverberation takes to the listener characteristics of the space where the sound is originated and its absence does not commonly sounds like “natural”. When recording sounds, it is not always possible to have the desirable characteristics of reverberation of an environment, therefore methods for artificial reverberation have been developed, always seeking a more efficient implementations and more faithful to the real environments. This work presents an implementation in FPGAs (Field Programmable Gate Arrays ) of a classic digital reverberation audio structure, based on a proposal of Manfred Schroeder, using sets of all-pass and comb filters. The developed system exploits the use of reconfigurable hardware as a platform development and implementation of digital audio effects, focusing on the modularity and reuse characteristics

Efficient Implementation Of A Single-Precision Floating-Point Arithmetic Unit on FPGA

This paper presents a single precision floating point arithmetic unit with support for multiplication, addition, fused multiply-add, reciprocal, square-root and inverse squareroot with high-performance and low resource usage. The design uses a piecewise 2nd order polynomial approximation to implement reciprocal, square-root and inverse square-root. The unit can be configured with any number of operations and is capable to calculate any function with a throughput of one operation per cycle. The floatingpoint multiplier of the unit is also used to implement the polynomial approximation and the fused multiply-add operation. We have compared our implementation with other state-of-the-art proposals, including the Xilinx Core-Gen operators, and conclude that the approach has a high relative performance/area efficiency. © 2014 Technical University of Munich (TUM).

Trends Of CPU, GPU and FPGA for high-performance computing

Floating-point computing with more than one TFLOP of peak performance is already a reality in recent Field-Programmable Gate Arrays (FPGA). General-Purpose Graphics Processing Units (GPGPU) and recent many-core CPUs have also taken advantage of the recent technological innovations in integrated circuit (IC) design and had also dramatically improved their peak performances. In this paper, we compare the trends of these computing architectures for high-performance computing and survey these platforms in the execution of algorithms belonging to different scientific application domains. Trends in peak performance, power consumption and sustained performances, for particular applications, show that FPGAs are increasing the gap to GPUs and many-core CPUs moving them away from high-performance computing with intensive floating-point calculations. FPGAs become competitive for custom floating-point or fixed-point representations, for smaller input sizes of certain algorithms, for combinational logic problems and parallel map-reduce problems. © 2014 Technical University of Munich (TUM).

A many-core co-processor for embedded parallel computing on FPGA

Single processor architectures are unable to provide the required performance of high performance embedded systems. Parallel processing based on general-purpose processors can achieve these performances with a considerable increase of required resources. However, in many cases, simplified optimized parallel cores can be used instead of general-purpose processors achieving better performance at lower resource utilization. In this paper, we propose a configurable many-core architecture to serve as a co-processor for high-performance embedded computing on Field-Programmable Gate Arrays. The architecture consists of an array of configurable simple cores with support for floating-point operations interconnected with a configurable interconnection network. For each core it is possible to configure the size of the internal memory, the supported operations and number of interfacing ports. The architecture was tested in a ZYNQ-7020 FPGA in the execution of several parallel algorithms. The results show that the proposed many-core architecture achieves better performance than that achieved with a parallel generalpurpose processor and that up to 32 floating-point cores can be implemented in a ZYNQ-7020 SoC FPGA.