Amperometric biosensor for ascorbic acid

A L-ascorbic acid biosensor based on ascorbate oxidase has been developed. The enzyme was extracted from the mesocarp of cucumber (Cucumis sativus) by using 0.05 mol L-1 phosphate buffer, pH 5.8 containing 0.5 mol L-1 NaCl. After the dialysis versus phosphate buffer 0.05 mol L-1 pH 5.8, the enzyme was immobilized onto nylon net through glutaraldehyde covalent bond. The membrane was coupled to an O2 electrode and the yielding reaction monitored by oxygen depletion at -600 mV using flow injection analysis optimized to 0.1 mol L-1 phosphate buffer pH 5.8, as the carrier solution and flow-rate of 0.5 mL min-1. The ascorbic acid calibration curve was linear from 1.2x10-4 to 1.0x10-3 mol L-1. The evaluation of biosensor lifetime leads to 500 injections. Commercial pharmaceutical samples were analyzed with the proposed method and the results were compared with those obtained by high-performance liquid chromatography (HPLC).

Interaction study of moxifloxacin with Cu(II) ion using square-wave voltammetry and its application in the determination in tablets

This work presents an electroanalytical method for the determination of moxifloxacin (MOXI) in tablets by its interaction with Cu(II) ion and subsequent electrochemical reduction at hanging mercury drop electrode (HMDE). A well-defined reduction peak at -0.21 V vs. Ag/AgCl in Phosphate buffer 0.04 mol L-1 pH 8.0 was observed for the complex reduction MOXI-Cu(II), using square-wave voltammetry (SWV). Using a 10 s of accumulation time at -0.40 V was found a limit detection of 3.60x10-8 mol l-1. The obtained results have shown good agreement with those obtained by spectrophotometric method.

Ascorbic acid determination using a carbon paste electrode modified with iron(III) ions adsorbed on humic acid

An amperometric sensor was constructed, by using humic acids to immobilize Fe3+ ions on a carbon paste electrode (CPE-HA-Fe), and used for ascorbic acid (H2A) determination. The cyclic voltammogram of the electrode showed electrochemical response due to the Fe3+/Fe2+ couple at E1/2=+0.78 V vs SCE, using 0.5 mol L-1 KCl and 0.2 mol L-1 acetate/0.020 mol L-1 phosphate buffer, at pH = 5.4, as supporting electrolyte. When H2A is added to the electrolyte solution it is observed an oxidation process. The oxidation current, obtained by chronoamperommetry at +0.87 V vs SCE, is proportional to the concentration, represented by the equation I(µA) = 7.6286 [H2A] (mmol L-1) + 1.9583, r = 0.9996, for concentrations between 0.0 and 1.4 mmol L-1. The electrode showed high stability and was used for H2A determination in a natural orange juice.

Methylene blue adsorption onto modified lignin from sugar cane bagasse

The adsorption kinetics and equilibrium of methylene blue (MB) onto reticulated formic lignin (RFL) from sugar cane bagasse was studied. The adsorption process is pH, temperature and ionic strength (µ) dependent and obeys the Langmuir model. Conditions for higher adsorption rate and capacity were determined. The faster adsorption (12 hours) and higher adsorption capacity (34.20 mg.g-1) were observed at pH = 5.8 (acetic acid-sodium acetate aqueous buffer), 50 ºC and 0.1 ionic strength. Under temperature (50 ºC) control and occasional mechanical stirring it took from 1 to 10 days to reach the equilibrium.

Highly sensitive spectrophotometric methods for the determination of olanzapine

Highly sensitive and selective spectrophotometric methods (A and B) were developed for the determination of micro amounts of olanzapine (OLZ). Method A (direct method) is based on the oxidation of olanzapine with a known excess of iodine monochloride (ICl) in an acidic medium. Under the same condition, thymol blue was iodinated by unreacted ICl, and the absorbance of uniodinated thymol blue was measured at 536 nm. The decrease in ICl concentration is a measure of drug concentration. In method B (indirect method), oxidation of OLZ by a known excess of Ce(IV) in sulfuric acid medium followed by the reaction of unreacted Ce(IV) with leuco crystal violet (LCV) to crystal violet (CV), which is measured in an acetate buffer medium ( pH 4.9) at 580 nm. These methods obey the Beer's law in the concentration range of 0.2-1.6 µg mL-1 (method A) and 0.1-1.4 µg mL-1 (method B). The developed procedures have been successfully applied to the determination of OLZ in pure and in dosage forms. The results exhibit no interference from the presence of excipients. The reliability of the methods was established by parallel determination of OLZ against the reference method.

Spectrophotometric flow injection system for determination of Zn2+ in ophthalmic formulations using Alizarin red S

A spectrophotometric flow injection method for the determination of Zn(II) in ophthalmic formulations was developed. In this work, Zn(II) ion was complexed with Alizarin red S in borate buffer solution (pH 9.0) and the chromophore produced was monitored at 520 nm. The analytical curve was linear in the Zn(II) concentration range from 6.05 x 10-6 to 1.50 x 10-4 mol L-1 with a detection limit of 3.60 x 10-6 mol L-1. Recoveries ranged from 96.3 to 105 % and a relative standard deviation of 1.2 % (n = 10) for 5.5x10-5 mol L-1 Zn(II) reference solution were obtained. The sampling rate was 60 h-1 and the results obtained of Zn(II) in ophthalmic products using this procedure are in close agreement with those obtained using a comparative spectrophotometric procedure at 95 % confidence level.

A pH optode based on thymol blue: application to determination of CO2 using flow injection analysis system

An optode based on thymol blue (TB), an acid-based indicator, has been constructed and evaluated as a detector in FIA system for CO2 determination. The dye was chemically immobilised on the surface of a bifurcated glass optical fibre bundle, using silanisation in organic media. In FIA system, hydrogen carbonate or carbonate samples are injected in a buffer carrier solution, and then are mixed with phosphoric acid solution to generate CO2, which diffuses through a PTFE membrane, in order to be collected in an acceptor carrier fluid, pumped towards to detection cell, in which the optode was adapted. The proposed system presents two linear response ranges, from 1.0 x 10-3 to 1.0 x 10-2 mol l-1, and from 2.0 x 10-2 to 0.10 mol l-1. The sampling frequency was 11 sample h-1, with good repeatability (R.S.D < 4 %, n = 10). In flow conditions the optode lifetime was 170 h. The system was applied in the analysis of commercial mineral water and the results obtained in the hydrogen carbonate determination did not differ significantly from those obtained by potentiometry, at a confidence level of 95 %.

Titrimetric and spectrophotometric assay of bupropion hydrochloride in pharmaceuticals using mercury(II) nitrate

Two simple, rapid and accurate methods for the determination of bupropion hydrochloride (BUP) in pure and in pharmaceutical preparations are described. Both methods are based on the measurement of the chloride of its hydrochloride. In the titrimetric method, the chloride content of bupropion hydrochloride is determined by titrating with mercury(II)nitrate using diphenylcarbazone-bromophenol blue as indicator. Titrimetric method is applicable over a range 2-20 mg of BUP and the reaction stoichiometry is found to be 2:1 (BUP: Hg(NO3)2). The spectrophotometric method involves the addition of a measured excess of mercury(II) nitrate reagent in formate buffer to the drug, and after ensuring the reaction had gone to completion, the unreacted mercury(II) is treated with a fixed amount of diphenylcarbazone, and absorbance measured at 515 nm. The absorbance is found to decrease linearly with increasing concentration of BUP and the calibration curve is linear over 1.0-15.0 µg mL-1 BUP. The proposed methods were successfully applied to the determination of BUP in commercially available dosage forms with good accuracy and precision, and without detectable interference by excipients. The accuracy was further ascertained by placebo blank and synthetic mixture analyses and also by recovery experiments via standard-addition procedure.

Spectrophotometric determination of nevirapine using tetrathiocyanatocobalt(II) ion as a reagent

A simple and rapid spectrophotometric method for the determination of nevirapine is described. The method is based on the reaction of nevirapine with tetrathiocyanatocobalt(II) ion in buffer of pH 4 to form the corresponding complex. Beer's law is obeyed in the range of 0.2 - 2.0 µg mL-1 for nevirapine. The optical parameters such as molar absorptivity, Sandell's sensitivity, detection limit and quantitation limit were found to be 1.16× 10(4) Lmol-1cm-1, 2.09 X 10-3 µg cm-2, 0.073 µg mL-1 and 0.222 µg mL-1 respectively. The optimum reaction conditions and other analytical parameters were evaluated. The statistical evaluation of the method was examined by determining intra-day and inter-day precision. The proposed method has been successfully applied for the determination of nevirapine in pharmaceutical formulations.

Effect of Potato virus X on total phenol and alkaloid contents in Datura stramonium leaves

The present paper reports results of the effect of Potato virus X (PVX) on the contents of total phenols and alkaloids in leaves of Datura stramonium. A significant decrease in the contents of phenols and alkaloids was observed in leaves inoculated with PVX (X-I). However, there was an increase in the percentage of phenols in leaves rubbed with phosphate buffer (C1-I) and in leaves from the nodes immediately above, possibly induced by mechanical injury. Gas chromatography/mass spectroscopy revealed amounts of scopolamine in samples submitted to all treatments, except X-I, in which the amount of this alkaloid was low. High amounts of an unidentified compound (molecular ion m/z 302 and a prominent peak at m/z 129) were noted in extracts from leaves X-I, C1-I and leaves from the nodes immediately above the leaves inoculated with PVX. It is suggested that the synthesis and accumulation of the unidentified compound is a result of stress from mechanical injury and virus inoculation.

Analysis of private natural heritage reserves as a conservation strategy for the biodiversity of the cocoa region of the southern State of Bahia, Brazil

Brazil was the first country in Latin America to establish and regulate this type of reserve, and there are currently more than 700 Private Nature Heritage Reserves (RPPN in Portuguese) officially recognized by either federal or state environmental agencies. Together, these RPPN protect more than a half million hectares of land in the country. The coastal forests in the southern part of Bahia State extend 100 to 200 km inland, gradually changing in physiognomy as they occupy the dryer inland areas. The coastal forest has been subjected to intense deforestation, and currently occupies less than 10% of its original area. For this work the creation processes of the RPPN were consulted to obtain the data creation time, size of property, the condition of the remaining forest, succession chain and the last paid tax. After that, interviews with the owners were made to confirm this data. Sixteen RPPN have been established in this region until 2005. Their sizes vary from 4.7 to 800 ha. Ten of these RPPN are located within state or federal conservation areas or their buffer zones. In spite of the numerous national and international conservation strategies and environmental policies focused on the region, the present situation of the cocoa zone is threatening the conservation of the region's natural resources. The establishment of private reserves in the cocoa region could conceivably improve these conservation efforts. This type of reserve can be established under a uniform system supported by federal legislation, and could count on private organizations.

Uso do solo na zona ripária de bacias agrícolas de pequeno a médio porte

As zonas ripárias situam-se às margens dos sistemas de drenagens de águas superficiais, afetando processos hidrológicos. O Código Florestal Brasileiro estabelece um afastamento mínimo ao longo dos cursos de águas, considerado como área de preservação permanente. Este trabalho objetivou determinar a distribuição do uso do solo em bacias agrícolas com várias dimensões para diferentes afastamentos em relação ao sistema de drenagem de águas superficiais. A metodologia utilizada compreendeu o uso de imagens do satélite SPOT-5, para classificação do uso de solo em seis bacias com áreas variando de 14 a 600 km². A precisão da classificação foi determinada pela acuracidade e o nível de acerto, determinado pelo coeficiente Kappa. A partir do sistema de drenagem foram traçadas linhas paralelas aos cursos de águas, denominados buffers, com afastamento das margens de 20, 30, 50, 100 e 200 m. Em cada buffer foi determinada a distribuição da ocupação do uso do solo. Os valores obtidos com a classificação indicaram acerto com coeficiente Kappa médio de 0,96. Os temas classificados em todas as imagens apresentaram boa acuracidade, com valores maiores que 96%. Os resultados apontaram que o uso da terra predominante em todas as bacias é a mata nativa com valores médios de 46,8%, seguida de culturas agrícolas com 24,7% e pastagens com 21,7%. As áreas de matas nativas apresentavam tendência de redução à medida que se afastavam dos cursos de água, enquanto os reflorestamentos tendiam a aumentar o percentual da área ocupada com o afastamento das margens dos rios.

Distribution of tree species in a geomorphological and pedological gradient of submontane semidecidual seasonal forest in the vicinity of Rio Doce state park, Minas Gerais

The objective of this study was to test the hypothesis that the distribution of tree species in a fragment of submontane seasonal semideciduous forest, a buffer zone in the Parque Estadual do Rio Doce, Minas Gerais, is influenced by geomorphological and weather and soil variables, therefore it can represent a source of information for the restoration of degraded areas where environmental conditions are similar to those of the study area. A detailed soil survey was conducted in the area by sampling three soil profiles per slope segment, totaling 12 profiles. To sample the topsoil, four composite samples were collected from the 10-20 cm layers in each topographic range totaling 16 composite samples. In the low ramp and the lower and upper concave slopes, the texture ranged from clay to sandy-clay. The soil and topographic gradient was characterized by changes in the soil physical-chemical properties. The soil in the 10-20 cm sampled layer was sandier, slightly more fertile and less acid in the low ramp than the clayer soil, nutrient-poor and highly acid soil at the top. The soil conditions in the lower and upper slope of the sampled layers, in turn, were intermediate. The P levels were limiting in all soils. The species distribution along the topographic gradient was associated with variations in chemical fertility, acidity and soil texture. The distribution of Pera leandri, Astronium fraxinifolium, Pouteria torta, Machaerium brasiliense and Myrcia rufipes was correlated with high aluminum levels and to low soil fertility and these species may be indicated for restoration of degraded areas on hillsides and hilltops in regions where environmental conditions are similar. The distribution of Pouteria venosa, Apuleia leiocarpa and Acacia polyphylla was correlated with the less acid and more fertile soil in the environment of the low ramps, indicating the potential for the restoration of similar areas.

Ação da l-arginina na evolução de retalhos cutâneos de ratos sob exposição à nicotina

OBJETIVO: Avaliar se o tratamento com L-arginina influencia a cicatrização de retalhos cutâneos em ratos expostos à nicotina. MÉTODOS: Foram utilizados 40 ratos Wistar pesando 142,4±10,1g separados em quatro grupos: GC- tratamento com solução tampão fosfatos pH 7,4, confecção de retalho cutâneo, observação por 10 dias; GN- exposição à nicotina por quatro semanas, confecção de retalho cutâneo, observação por dez dias; GA- tratamento com solução tampão fosfatos pH 7,4 por quatro semanas, confecção de retalho cutâneo, tratamento com arginina por dez dias; GAN- exposição à nicotina por quatro semanas, confecção de retalho cutâneo, tratamento com arginina por dez dias. Foram avaliadas as áreas de necrose, re-epitelização, reação inflamatória e formação de tecido de granulação, pela coloração HE, a área de deposição total e a diferenciação de colágenos I e III por histometria com a coloração de picrosirius, e, através da marcação imunoistoquímica com anticorpo monoclonal anti-CD34, a densidade vascular cicatricial. RESULTADOS: As porcentagens de áreas de necrose de GN e GNA foram maiores (p<0,001) do que GC e GA. Nos escores histológicos, a deposição de colágeno e a porcentagem de colágeno tipo I, no GC e GA foram similares (p>0,05) e maiores (p<0,001) do que em GA e em GNA e, nas densidades vasculares, GN e GAN foram menores (p<0,001) do que em GC e em GA. CONCLUSÃO: A exposição à nicotina inibiu os efeitos da arginina, e nos ratos não expostos, induziu melhora na angiogênese e na deposição de colágeno total nos retalhos cutâneos.

Criopreservação de sêmen humano: comparação entre métodos de congelação e tipos de envase

OBJETIVOS: comparar duas diferentes técnicas de congelação e dois tipos de envase do sêmen humano durante processo de criopreservação. MÉTODOS: estudo experimental, no qual foi analisada a criopreservação de 18 amostras de sêmen de 18 voluntários. Após a adição de meio crioprotetor, "Test-yolk buffer" , as amostras de sêmen foram envasadas em palhetas com capacidade de 0,25 mL ou em criotubos de 2 mL e submetidas à criopreservação por dois métodos, um lento e outro rápido, totalizando quatro tratamentos distintos: RP (congelação pelo método rápido e envasado em palheta), RT (rápido-criotubo), LP (lento-palheta) e LT (lento-criotubo). As amostras, após 24 horas, foram descongeladas em temperatura ambiente e mantidas a 37ºC. Os dados coletados foram analisados através do teste t de Student, com p<0,05, utilizando o programa de computador SPSS for Windows® versão 11.0.0. RESULTADOS: houve redução da motilidade espermática após o processo de criopreservação. A taxa de motilidade inicial foi 58,1% e as motilidades após os diferentes métodos de criopreservação foram: 19,2% (RP), 27% (RT), 21,1% (LP) e 30,3% (LT). Houve redução significativa na morfologia normal. A taxa de morfologia normal inicial foi 14,2% e as morfologias após os diferentes métodos de criopreservação foram: 12,8% (RP), 12,6% (RT), 12,6% (LP) e 12,4% (LT). CONCLUSÕES: o método de criopreservação lento com envase em criotubo esteve associado à melhor motilidade espermática após o descongelamento. Não houve diferença entre os métodos quando avaliada a morfologia espermática.