Confocal microscopy applied to the study of single entity fluorescence and light scattering

A sample scanning confocal optical microscope (SCOM) was designed and constructed in order to perform local measurements of fluorescence, light scattering and Raman scattering. This instrument allows to measure time resolved fluorescence, Raman scattering and light scattering from the same diffraction limited spot. Fluorescence from single molecules and light scattering from metallic nanoparticles can be studied. First, the electric field distribution in the focus of the SCOM was modelled. This enables the design of illumination modes for different purposes, such as the determination of the three-dimensional orientation of single chromophores. Second, a method for the calculation of the de-excitation rates of a chromophore was presented. This permits to compare different detection schemes and experimental geometries in order to optimize the collection of fluorescence photons. Both methods were combined to calculate the SCOM fluorescence signal of a chromophore in a general layered system. The fluorescence excitation and emission of single molecules through a thin gold film was investigated experimentally and modelled. It was demonstrated that, due to the mediation of surface plasmons, single molecule fluorescence near a thin gold film can be excited and detected with an epi-illumination scheme through the film. Single molecule fluorescence as close as 15nm to the gold film was studied in this manner. The fluorescence dynamics (fluorescence blinking and excited state lifetime) of single molecules was studied in the presence and in the absence of a nearby gold film in order to investigate the influence of the metal on the electronic transition rates. The trace-histogram and the autocorrelation methods for the analysis of single molecule fluorescence blinking were presented and compared via the analysis of Monte-Carlo simulated data. The nearby gold influences the total decay rate in agreement to theory. The gold presence produced no influence on the ISC rate from the excited state to the triplet but increased by a factor of 2 the transition rate from the triplet to the singlet ground state. The photoluminescence blinking of Zn0.42Cd0.58Se QDs on glass and ITO substrates was investigated experimentally as a function of the excitation power (P) and modelled via Monte-Carlo simulations. At low P, it was observed that the probability of a certain on- or off-time follows a negative power-law with exponent near to 1.6. As P increased, the on-time fraction reduced on both substrates whereas the off-times did not change. A weak residual memory effect between consecutive on-times and consecutive off-times was observed but not between an on-time and the adjacent off-time. All of this suggests the presence of two independent mechanisms governing the lifetimes of the on- and off-states. The simulated data showed Poisson-distributed off- and on-intensities, demonstrating that the observed non-Poissonian on-intensity distribution of the QDs is not a product of the underlying power-law probability and that the blinking of QDs occurs between a non-emitting off-state and a distribution of emitting on-states with different intensities. All the experimentally observed photo-induced effects could be accounted for by introducing a characteristic lifetime tPI of the on-state in the simulations. The QDs on glass presented a tPI proportional to P-1 suggesting the presence of a one-photon process. Light scattering images and spectra of colloidal and C-shaped gold nano-particles were acquired. The minimum size of a metallic scatterer detectable with the SCOM lies around 20 nm.

Aggregation of hybrid molecules and film formation of colloidal monolayers

A unique characteristic of soft matter is its ability to self-assemble into larger structures. Characterizing these structures is crucial for their applications. In the first part of this work, I investigated DNA-organic hybrid material by means of Fluorescence Correlation Spectroscopy (FCS) and Fluorescence Cross-Correlation Spectroscopy (FCCS). DNA-organic hybrid materials, a novel class of hybrid materials composed of synthetic macromolecules and oligodeoxynucleotide segmenta, are mostly amphiphilic and can self-assemble into supramolecular structures in aqueous solution. A hybrid material of a fluorophore, perylenediimide (PDI), and a DNA segment (DNA-PDI) has been developed in Prof. A. Hermann’s group (University of Groningen). This novel material has the ability to form aggregates through pi-pi stacking between planar PDIs and can be traced in solution due to the fluorescence of PDI. I have determined the diffusion coefficient of DNA-PDI conjugates in aqueous solution by means of FCS. In addition, I investigated whether such DNA-PDIs form aggregates with certain structure, for instance dimers. rnOnce the DNA hybrid material self-assemble into supermolecular structures for instance into micelles, the single molecules do not necessarily stay in one specific micelle. Actually, a single molecule may enter and leave micelles constantly. The average residence time of a single molecule in a certain micelle depends on the nature of the molecule. I have chosen DNA-b-polypropylene oxide (PPO) as model molecules and investigated the residence time of DNA-b-PPO molecules in their according micelles by means of FCCS.rnBesides the DNA hybrid materials, polymeric colloids can also form ordered structures once they are brought to an air/water interface. Here, hexagonally densely packed monolayers can be generated. These monolayers can be deposited onto different surfaces as coating layers. In the second part of this work, I investigated the mechanical properties of such colloidal monolayers using micromechanical cantilevers. When a coating layer is deposited on a cantilever, it can modify the elasticity of the cantilever. This variation can be reflected either by a deflection or by a resonance frequency shift of the cantilever. In turn, detecting these changes provides information about the mechanical properties of the coating layer. rnIn the second part of this work, polymeric colloidal monolayers were coated on a cantilever and homogenous polymer films of a few hundred nanometers in thickness were generated from these colloidal monolayers by thermal annealing or organic vapor annealing. Both the film formation process and the mechanical properties of these resulting homogenous films were investigated by means of cantilever. rnElastic property changes of the coating film, for example upon absorption of organic vapors, induce a deflection of the cantilever. This effect enables a cantilever to detect target molecules, when the cantilever is coated with an active layer with specific affinity to target molecules. In the last part of this thesis, I investigated the applicability of suitably functionalized micromechanical cantilevers as sensors. In particular, glucose sensitive polymer brushes were grafted on a cantilever and the deflection of this cantilever was measured during exposure to glucose solution. rn

Strukturbildung doppelthydrophiler Blockcopolymere mit mehrwertigen organischen Gegenionen

Sowohl die Komplexierung von Polyelektrolyten mit anorganischen Salzen, als auch die mit entgegengesetzt geladenen Polymeren wurde von vielen Autoren bereits intensiv untersucht. Doch gerade mit Molekülen die zwischen diesen beiden Extremen liegen, sollte es möglich sein, durch elektrostatische Wechselwirkungen gezielt nanometergroße Teilchen definierter Struktur herzustellen. Ziel dieser Arbeit war es deshalb, die Strukturbildung doppelthydrophiler Blockcopolymere mit mehrwertigen organischen Gegenionen zu untersuchen und insbesondere Parameter für die Bildung supramolekularer Strukturen in wässriger Lösung zu finden. Als Blockcopolymer wurde dabei Polyethylenoxid-b-methacrylsäure mittels anionischer Polymerisation hergestellt und mittels Gelpermeationschromatographie (GPC) und Kernresonanzspektroskopie (NMR)charakterisiert. Die Strukturbildung des Polyelektrolyten mit mehrwertigen organischen Gegenionen wurde in pH = 6- und pH = 7-Pufferlösung mit dynamischer und statischer Lichtstreuung, Kleinwinkelneutronenstreuung und Ultrazentrifugation untersucht. Mit Diaminobenzidin als Gegenion wurden dabei sphärische Komplexe mit einem hydrodynamischen Radius um 100 nm erhalten und mit Ultrazentrifugation der Anteil des Gegenions im Komplex quantifiziert. Die schlechte Löslichkeit des Diaminobenzidins in wässrigem Medium erschwerte allerdings die Interpretation der Ergebnisse. Trotzdem deuten diese darauf hin, dass keine Kolloidbildung des Diaminobenzidins, sondern eine Komplexierung der Einzelmoleküle mit dem Copolymer vorliegt. Um Probleme mit der Löslichkeit zu vermeiden, wurden schliesslich Polyamidoamin-Dendrimere als Gegenionen verwendet. Dabei wurde in pH = 6- und pH = 7-Pufferlösung für Dendrimere der Generation 4 mit steigender Gegenionenkonzentration ein kontinuierlicher Anstieg des hydrodynamischen Radius bis zu einer Größe von 70 nm gefunden. Mit Kleinwinkelneutronenstreuung konnte eine ellipsoidale Struktur dieser Komplexe beobachtet werden. Auch die Größe der Gegenionen spielt für die Bildung supramolekularer Aggregate eine Rolle. So zeigte sich, dass für Polyamidoamin-Dendrimere der Generation 2, analog zu denen der Generation 4, ein Anstieg des hydrodynamischen Radius mit steigender Gegenionenkonzentration zu beobachten ist. Für Generation 0-Dendrimere hingegen wurde ein umgekehrter Verlauf beobachtet, welcher dem für Diaminobenzidin gleicht. Somit kann man annehmen, dass die Aggregation mit kleinen Molekülen zu einer anderen Struktur der Komplexe führt, als die mit größeren Molekülen.

DNA block copolymers – from micelles to machines

DNA block copolymer, a new class of hybrid material composed of a synthetic polymer and an oligodeoxynucleotide segment, owns unique properties which can not be achieved by only one of the two polymers. Among amphiphilic DNA block copolymers, DNA-b-polypropylene oxide (PPO) was chosen as a model system, because PPO is biocompatible and has a Tg < 0 °C. Both properties might be essential for future applications in living systems. During my PhD study, I focused on the properties and the structures of DNA-b-PPO molecules. First, DNA-b-PPO micelles were studied by scanning force microscopy (SFM) and fluorescence correlation spectroscopy (FCS). In order to control the size of micelles without re-synthesis, micelles were incubated with template-independent DNA polymerase TdT and deoxynucleotide triphosphates in reaction buffer solution. By carrying out ex-situ experiments, the growth of micelles was visualized by imaging in liquid with AFM. Complementary measurements with FCS and polyacrylamide gel electrophoresis (PAGE) confirmed the increase in size. Furthermore, the growing process was studied with AFM in-situ at 37 °C. Hereby the growth of individual micelles could be observed. In contrast to ex-situ reactions, the growth of micelles adsorbed on mica surface for in-situ experiments terminated about one hour after the reaction was initiated. Two reasons were identified for the termination: (i) block of catalytic sites by interaction with the substrate and (ii) reduced exchange of molecules between micelles and the liquid environment. In addition, a geometrical model for AFM imaging was developed which allowed deriving the average number of mononucleotides added to DNA-b-PPO molecules in dependence on the enzymatic reaction time (chapter 3). Second, a prototype of a macroscopic DNA machine made of DNA-b-PPO was investigated. As DNA-b-PPO molecules were amphiphilic, they could form a monolayer at the air-water interface. Using a Langmuir film balance, the energy released owing to DNA hybridization was converted into macroscopic movements of the barriers in the Langmuir trough. A specially adapted Langmuir trough was build to exchange the subphase without changing the water level significantly. Upon exchanging the subphase with complementary DNA containing buffer solution, an increase of lateral pressure was observed which could be attributed to hybridization of single stranded DNA-b-PPO. The pressure versus area/molecule isotherms were recorded before and after hybridization. I also carried out a series of control experiments, in order to identify the best conditions of realizing a DNA machine with DNA-b-PPO. To relate the lateral pressure with molecular structures, Langmuir Blodgett (LB) films were transferred to highly ordered pyrolytic graphite (HOPG) and mica substrates at different pressures. These films were then investigated with AFM (chapter 4). At last, this thesis includes studies of DNA and DNA block copolymer assemblies with AFM, which were performed in cooperation with different group of the Sonderforschungsbereich 625 “From Single Molecules to Nanoscopically Structured Materials”. AFM was proven to be an important method to confirm the formation of multiblock copolymers and DNA networks (chapter 5).

Simulations of charge transport in organic compounds

To aid the design of organic semiconductors, we study the charge transport properties of organic liquid crystals, i.e. hexabenzocoronene and carbazole macrocycle, and single crystals, i.e. rubrene, indolocarbazole and benzothiophene derivatives (BTBT, BBBT). The aim is to find structure-property relationships linking the chemical structure as well as the morphology with the bulk charge carrier mobility of the compounds. To this end, molecular dynamics (MD) simulations are performed yielding realistic equilibrated morphologies. Partial charges and molecular orbitals are calculated based on single molecules in vacuum using quantum chemical methods. The molecular orbitals are then mapped onto the molecular positions and orientations, which allows calculation of the transfer integrals between nearest neighbors using the molecular orbital overlap method. Thus we obtain realistic transfer integral distributions and their autocorrelations. In case of organic crystals the differences between two descriptions of charge transport, namely semi-classical dynamics (SCD) in the small polaron limit and kinetic Monte Carlo (KMC) based on Marcus rates, are studied. The liquid crystals are investigated solely in the hopping limit. To simulate the charge dynamics using KMC, the centers of mass of the molecules are mapped onto lattice sites and the transfer integrals are used to compute the hopping rates. In the small polaron limit, where the electronic wave function is spread over a limited number of neighboring molecules, the Schroedinger equation is solved numerically using a semi-classical approach. The results are compared for the different compounds and methods and, where available, with experimental data. The carbazole macrocycles form columnar structures arranged on a hexagonal lattice with side chains facing inwards, so columns can closely approach each other allowing inter-columnar and thus three-dimensional transport. When taking only intra-columnar transport into account, the mobility is orders of magnitude lower than in the three-dimensional case. BTBT is a promising material for solution-processed organic field-effect transistors. We are able to show that, on the time-scales of charge transport, static disorder due to slow side chain motions is the main factor determining the mobility. The resulting broad transfer integral distributions modify the connectivity of the system but sufficiently many fast percolation paths remain for the charges. Rubrene, indolocarbazole and BBBT are examples of crystals without significant static disorder. The high mobility of rubrene is explained by two main features: first, the shifted cofacial alignment of its molecules, and second, the high center of mass vibrational frequency. In comparsion to SCD, only KMC based on Marcus rates is capable of describing neighbors with low coupling and of taking static disorder into account three-dimensionally. Thus it is the method of choice for crystalline systems dominated by static disorder. However, it is inappropriate for the case of strong coupling and underestimates the mobility of well-ordered crystals. SCD, despite its one-dimensionality, is valuable for crystals with strong coupling and little disorder. It also allows correct treatment of dynamical effects, such as intermolecular vibrations of the molecules. Rate equations are incapable of this, because simulations are performed on static snapshots. We have thus shown strengths and weaknesses of two state of the art models used to study charge transport in organic compounds, partially developed a program to compute and visualize transfer integral distributions and other charge transport properties, and found structure-mobility relations for several promising organic semiconductors.

Untersuchungen zu Migration, Homing und Effektor-Funktionen humaner T-Lymphozyten in NOD.Cg-Prkdc scid Il2r gtm1Wjl, SzJ-Mäusen im Rahmen der allogenen hämatopoetischen Stammzelltransplantation

Die akute myeloische Leukämie (AML) zählt zu den aggressivsten neoplastischen Erkrankungenrnder Hämatopoese. Die Mehrheit der Patienten mit AML erreicht nach Induktions-rnChemotherapie den Zustand der kompletten Remission, jedoch erleiden mehr als die Hälfterndieser Patienten anschließend einen Rückfall und versterben an den Folgen der Erkrankungrn[1]. Die allogene hämatopoetische Stammzelltransplantation (engl.: hematopoietic stem cellrntransplantation, HSCT) stellt die einzig putativ kurative Behandlungsform für rezidierendernPatienten und solche mit schlechter Prognose dar. Jedoch birgt diese Form der Therapiernauch eine Vielzahl an Risiken. Insbesondere das Auftreten einer akuten Transplantat-gegen-rnWirt-Erkrankung (engl.: graft-versus-host disease, GvHD) stellt die Hauptursache für transplantationsassoziierternMortalität und Morbidität dar [2]. Die Depletion von alloreaktiven zytotoxischenrnT Lymphozyten (CTL) aus dem Transplantat ermöglicht zwar die Prävention derrnEntstehung einer GvH-Erkrankung, jedoch häufig unter gleichzeitigem Verlust des förderlichen,rnanti-leukämischen Transplantat-gegen-Leukämie-Effekts (engl.: graft-versus-leukemia,rnGvL) [3]. Um den GvL-Effekt unter Vermeidung einer GvH-Erkrankung zu erhalten, bietetrnsich der gezielte adoptive Transfer von Leukämie-spezifischen, nicht alloreaktiven CTL alsrnattraktive Strategie der Immuntherapie für AML-Patienten nach allogener HSCT an. In derrnvorliegenden Arbeit konnte erfolgreich ein prä-klinisches murines AML-Modell unter Einsatzrndes stark immundefizienten NOD.Cg-Prkdcscid Il2rgtm1Wjl/SzJ- (NSG-) Mausstamms und primärenrnAML-Blasten durch die Optimierung bereits publizierter Protokolle etabliert werden.rnBei zehn von 17 transplantierten primären AML-Proben konnte ein erfolgreiches Engraftmentrnder humanen Zellen und eine Rekonstitution der humanen Neoplasie in den NSG-Mäusenrnerzielt werden. Die Engraftment-Rate betrug somit 58,82% und lag etwas unter dem aus derrnLiteratur bekannten Wert von 65-70% [4, 5]. Es ließen sich gut, intermediär und schlecht anwachsendernAML-Proben anhand der Engraftment-Stärke und -Reproduzierbarkeit voneinanderrnunterscheiden. Anhand der Analyse von für das Engraftment kritischer Parameter konnternein Zusammenhang zwischen Engraftment-Rate in der Maus und Flt3-Mutationsstatus sowiernFAB-Klassifikation des Patienten hergestellt und somit Angaben aus der Literatur bestätigtrnwerden. Für zwei Patienten-spezifische AML-Modelle, MZ580 und MZ308, konnten in vitrornerfolgreich AML-reaktive, über einzelne bzw. duale HLA-Diskrepanzen restringierte CTLPopulationenrngeneriert und über einen Zeitraum von bis zu 70 Tagen expandiert werden.rnDeren adoptiver Transfer in zuvor mit humanen AML-Blasten inokulierte NSG-Mäuse führternzu einer nahezu vollständigen Eradikation der AML-Blasten und Remission der Versuchstiere.rnAnhand unterschiedlich langer in vitro Kultur-Zeiträume konnte ein für die in vivo ausgeübtenrnEffektor-Funktionen optimaler Reifungszustand der CTL-Populationen von maximalrn28 Tagen bestimmt werden. Die kinetische Analyse der lytischen Aktivität in vivo deutete auf eine relativ schnelle Ausübung der Effektor-Funktionen durch die CTL-Populationen innerhalbrnvon zwei bis 24 Stunden nach adoptivem Transfer hin. Durch die Verwendung von inrnvitro generierten EBV-reaktiven CTL aus einem irrelevanten Spender konnte zudem die Spezifitätrnder in vivo ausgeübten Effektor-Funktionen nachgewiesen werden. Die ex vivo Re-rnIsolation adoptiv transferierter CTL und deren in vitro Analyse in einem IFNγ ELISpot wiesrneine konstante Reaktivität der Zellen ohne Induktion einer Xeno-Reaktivität nach. Die zurrnVerbesserung der Persistenz humaner CTL-Populationen eingesetzten autologen CD4+ TrnZellen zeigten nur im AML MZ308-System eine positive Wirkung. Generell konnte die Persistenzrnin vivo jedoch trotz initialer Substitution mit den Zytokinen IL-2 und IL-7 nicht über einenrnZeitraum von sieben Tagen hinaus aufrechterhalten werden.rnZur Untersuchung des Extravasations-Mechanismus humaner T Zellen über murines Endothelrnwurden sowohl Flusskammer- als auch Transwell-Studien durchgeführt, um die molekularenrnGrundlagen des Adhäsions- und Transmigrationsprozesses aufzuklären. Durch denrnparallelen Einsatz humaner und muriner T Zellen auf murinen Endothelzellen unter Zusatzrnfunktionsblockierender monoklonaler Antikörper konnte gezeigt werden, dass derrnExtravasations-Mechanismus beider Spezies auf Interaktionen homologer Adhäsionsmolekül-rnPaare, nämlich VLA-4–VCAM-1 und LFA-1–ICAM-1, beruht. Für einzelne Moleküle konntenrnin Abhängigkeit der eingesetzten Endothelzellen Unterschiede in der Funktionalität zwischenrnden Spezies identifiziert werden. Der Adhäsionsprozess war durch die Blockade derrnVLA-4–VCAM-1-Interaktion stärker inhibierbar als durch die Blockade von LFA-1–ICAM-1.rnDie Transmigration hingegen war durch die Blockade beider Adhäsionsmolekül-Paare vergleichbarrnstark inhibierbar.

Tracer diffusion at water-oil interfaces studied by fluorescence correlation spectroscopy

The adsorption of particles and surfactants at water-oil interfaces has attracted continuous attention because of its emulsion stabilizing effect and the possibility to form two-dimensional materials. Herein, I studied the interfacial diffusion of single molecules and nanoparticles at water-oil interfaces using fluorescence correlation spectroscopy. rnrnFluorescence correlation spectroscopy (FCS) is a promising technique to study diffusion of fluorescent tracers in diverse conditions. This technique monitors and analyzes the fluorescence fluctuation caused by single fluorescent tracers coming in and out of a diffraction-limited observation volume “one at a time”. Thus, this technique allows a combination of high precision, high spatial resolution and low tracer concentration. rnrnIn chapter 1, I discussed some controversial questions regarding the properties of water-hydrophobic interfaces and also introduced the current progress on the stability and dynamic of single nanoparticles at water-oil interfaces. The materials and setups I used in this thesis were summarized in chapter 2. rnrnIn chapter 3, I presented a new strategy to study the properties of water-oil interfaces. The two-dimensional diffusion of isolated molecular tracers at water/n-alkane interfaces was measured using fluorescence correlation spectroscopy. The diffusion coefficients of larger tracers with a hydrodynamic radius of 4.0 nm agreed well with the values calculated from the macroscopic viscosities of the two bulk phases. However, for small molecule tracers with hydrodynamic radii of only 1.0 and 0.6 nm, notable deviations were observed, indicating the existence of an interfacial region with a reduced effective viscosity. rnrnIn chapter 4, the interfacial diffusion of nanoparticles at water-oil interfaces was investigated using FCS. In stark contrast to the interfacial diffusion of molecular tracers, that of nanoparticles at any conditions is slower than the values calculated in accordance to the surrounding viscosity. The diffusion of nanoparticles at water-oil interfaces depended on the interfacial tension of liquid-liquid interfaces, the surface properties of nanoparticles, the particle sizes and the viscosities of surrounding liquid phases. In addition, the interfacial diffusion of nanoparticles with Janus motif is even slower than that of their symmetric counterparts. Based on the experimental results I obtained, I drew some possibilities to describe the origin of nanoparticle slowdown at water-oil interfaces.

Einzelmolekülspektroskopische Untersuchung von Rylenfarbstoffen zur elektronischen Wechselwirkung in multichromophoren Systemen und zur thermischen Besetzung molekularer Schwingungszustände

Im ersten Teil der Arbeit wurde die Abstandsabhängigkeit des elektronischen Kopplungsverhaltens für eine homologe Reihe von Perylendiimid-Dimeren (PDI-(Ph)x-PDI, x=0-3) mithilfe der Einzelmolekülspektroskopie bei tiefen Temperaturen untersucht. Während für große Abstände überwiegend „schwache“ Kopplung dominierte, wurde für den kleinsten Abstand „starke“ Kopplung gefunden. Im Gegensatz dazu zeigte das p-Phenylen-verbrückte Dimer (x=1) in Abhängigkeit vom untersuchten Molekül ein für beide Grenzfälle typisches Verhalten. Hier entscheidet die Größe der Kopplungsstärke im Vergleich zum statischen Energieunterschied, welcher Kopplungsmechanismus vorliegt. Die homologe Reihe ermöglichte zusätzlich die quantitative Untersuchung der Abstandsabhängigkeit der elektronischen Kopplungsstärke im Grenzfall „schwacher“ Kopplung. Sie konnte direkt aus der zugrunde liegenden Energietransferdynamik ermittelt werden. Der Vergleich mit quantenchemisch berechneten Werten lieferte eine gute Übereinstimmung. Die Abweichung betrug lediglich 20%.rnIm zweiten Teil der Arbeit wurde die thermische Besetzung der Schwingungszustände einzelner Terrylen-Moleküle untersucht. Im elektronischen Grundzustand konnte sie mithilfe von anti-Stokes-Fluoreszenz infolge von „Hot Band“ Absorption nachgewiesen werden. Darüber hinaus wurde Fluoreszenz aus höheren Schwingungszuständen des elektronisch angeregten Zustandes gefunden, die auf „Hot Band“ Emission infolge von thermischer Besetzung zurückgeführt werden konnte. Durch die Kombination von Emissions- und Anregungsspektroskopie konnte die Temperaturabhängigkeit beider Prozesse im Temperaturbereich von 209-311 K untersucht werden. Sie folgt der Boltzmann-Statistik, was eine Temperaturmessung mit einzelnen Molekülen ermöglicht. rn

DNA hybrid materials consisting of oligonucleotides and organic molecules: synthesis, characterization and applications

The goal of this thesis was to increase the functionality of pristine DNA scaffolds by functionalizing them with fluorescent dyes and hydrophobic moieties. Two important steps were necessary to realize this aim successfully. First, nucleic acids needed to be synthesized making use of multidisciplinary toolbox for the generation and manipulation of polynucleic acids. The most important techniques were the solid phase synthesis involving the incorporation of standard and modified phosphoramidite building blocks as well as molecular biology procedures like the polymerase chain reaction, the bacterial amplification of plasmids and the enzymatic digestion of circular vectors. Second, and evenly important, was the characterization of the novel bioorganic hybrid structures by a multitude of techniques, especially optical measurements. For studying DNA-dye conjugates methods like UV/Vis and photoluminescence spectroscopy as well as time resolved luminescence spectroscopy were utilized. While these measurements characterized the bulk behavior of an ensemble of DNA-dye hybrids it was necessary for a complete understanding of the systems to look at single structures. This was done by single-molecule fluorescence spectroscopy and fluorescence correlation spectroscopy. For complete analysis the optical experiments were complemented by direct visualization techniques, i.e. high resolution transmission electron microscopy and scanning force microscopy.

Structure formation of amphiphilic molecules at the air,water interface and after film transfer

One of the basic concepts of molecular self-assembly is that the morphology of the aggregate is directly related to the structure and interaction of the aggregating molecules. This is not only true for the aggregation in bulk solution, but also for the formation of Langmuir films at the air/water interface. Thus, molecules at the interface do not necessarily form flat monomolecular films but can also aggregate into multilayers or surface micelles. In this context, various novel synthetic molecules were investigated in terms of their morphology at the air/water interface and in transferred films. rnFirst, the self-assembly of semifluorinated alkanes and their molecular orientation at the air/water interface and in transferred films was studied employing scanning force microscopy (SFM) and Kelvin potential force microscopy. Here it was found, that the investigated semifluorinated alkanes aggregate to form circular surface micelles with a diameter of 30 nm, which are constituted of smaller muffin-shaped subunits with a diameter of 10 nm. A further result is that the introduction of an aromatic core into the molecular structure leads to the formation of elongated surface micelles and thus implements a directionality to the self-assembly. rnSecond, the self-assembly of two different amphiphilic hybrid materials containing a short single stranded desoxyribonucleic acid (DNA) sequence was investigated at the air/water interface. The first molecule was a single stranded DNA (11mer) molecule with two hydrophobically modified 5-(dodec-1-ynyl)uracil nucleobases at the terminal 5'-end of the oligonucleotide sequence. Isotherm measurements revealed the formation of semi-stable films at the air/water interface. SFM imaging of films transferred via Langmuir-Blodgett technique supported this finding and indicated mono-, bi- and multilayer formation, according to the surface pressure applied upon transfer. Within these films, the hydrophilic DNA sequence was oriented towards air covering 95% of the substrate.rnSimilar results were obtained with a second type of amphiphile, a DNA block copolymer. Furthermore, the potential to perform molecular recognition experiments at the air/water interface with these DNA hybrid materials was evaluated.rnThird, polyglycerol ester molecules (PGE), which are known to form very stable foams, were studies. Aim was to elucidate the molecular structure of PGE molecules at the air/water interface in order to comprehend the foam stabilization mechanism. Several model systems mimicking the air/water interface of a PGE foam and methods for a noninvasive transfer were tested and characterized by SFM. It could be shown, that PGE stabilizes the air/water interface of a foam bubble by formation of multiple surfactant layers. Additionally, a new transfer technique, the bubble film transfer was established and characterized by high speed camera imaging.The results demonstrate the diversity of structures, which can be formed by amphiphilic molecules at the air/water interface and after film transfer, as well as the impact of the chemical structure on the aggregate morphology.