Fluorescence close to dielectric interfaces

The aim of the work was to study the correlation between the orientation and excited-state lifetimes of organic dyes close to dielectric interfaces. For this purpose, an experimental setup was designed and built, guiding the light through a prism in total internal reflection geometry. Fluorescence intensities and lifetimes for an ensemble of dye molecules were analyzed as a function of the excitation and detection polarizations. Working close to the total internal reflection angle, the differences between polarization combinations were enhanced. A classical electromagnetic model that assumes a chromophore as a couple of point-like electrical dipoles was developed. A numerical method to calculate the excitation and emission of dye molecules embedded in a multilayer system was implemented, by which full simulation of the time resolved fluorescence experiments was achieved. Free organic dyes and organic dyes covalently bound to polyelectrolyte chains were used. The polymer functionalization process avoided aggregation and provided control over the dyes position, within a few nanometers to the interface. Moreover, by varying the pH, the polymer chains could be deposited on different substrates with different conformations and the resulting fluorescence characteristics analyzed. Initially the fluorescence of organic dyes embedded in a polymer matrix was studied as a function of the distance between the fluorophores and the polymer-air interface. The non-radiative decay rate, vacuum decay rate and the relative angle between the excitation and emission dipoles of the chromophores could be determined. Different free organic dyes were deposited onto different dielectric spacers, as close as possible to the air-dielectric interface. Surprisingly, the fluorescence characteristics of dyes deposited onto polyelectrolyte layer were in good agreement with theoretical predictions of dyes in a polymer matrix, even when the layer was only 2 nm thick. When functionalized chains were deposited at low pH, on top of a polyelectrolyte spacer, the fluorescence had the characteristics of emitters embedded in a polymer matrix as well. Surface deposition at high pH showed an intermediate behaviour between emitters embedded in polymer and on top of the surface, in air. In general, for low pH values, the chains are deposited on a substrate in a train-like conformation. For high pH values, the chains are deposited in a loop-like conformation. As a consequence at low pH the functionalized polymer strongly interdigitates with the polyelectrolyte chains of the spacer, bringing most of the dyes inside the polymer. Thus, the fluorophores may experience the polymer as surrounding environment. On the other hand, for high pH values the dye-loaded chains adsorbed have a conformational arrangement of dense loops that extend away from the surface. Therefore many fluorophores experience the air as surrounding environment. Changing the spacer from polyelectrolyte to negatively charged silane produced contradictory results for lifetimes and intensities. The fluorescence intensities indicated the behaviour of emitters embedded in a polymer matrix, regardless of the pH value. On the other hand, for low pH values, the excited-state lifetimes showed that the emitters behaved as in air. For higher pH values, an intermediate behaviour between fluorophores located within and above of a dielectric film was observed. The poor agreement between theoretical and experimental data may be due to the simplified model utilized, by which the dipoles are assumed either in one side or in the other with respect to a geometrical air-dielectric interface. In the case when the dielectric film is constituted by the functionalized polymer chains themselves, reality is more complex and a different model may apply. Nevertheless, possible applications of the technique arise from a qualitative analysis.

Detection of small buried objects: asymptotic factorization and MUSIC

In this work, we consider a simple model problem for the electromagnetic exploration of small perfectly conducting objects buried within the lower halfspace of an unbounded two–layered background medium. In possible applications, such as, e.g., humanitarian demining, the two layers would correspond to air and soil. Moving a set of electric devices parallel to the surface of ground to generate a time–harmonic field, the induced field is measured within the same devices. The goal is to retrieve information about buried scatterers from these data. In mathematical terms, we are concerned with the analysis and numerical solution of the inverse scattering problem to reconstruct the number and the positions of a collection of finitely many small perfectly conducting scatterers buried within the lower halfspace of an unbounded two–layered background medium from near field measurements of time–harmonic electromagnetic waves. For this purpose, we first study the corresponding direct scattering problem in detail and derive an asymptotic expansion of the scattered field as the size of the scatterers tends to zero. Then, we use this expansion to justify a noniterative MUSIC–type reconstruction method for the solution of the inverse scattering problem. We propose a numerical implementation of this reconstruction method and provide a series of numerical experiments.

The development of stylolites, from small-scale heterogeneities to multi-scale roughness

Stylolites are rough paired surfaces, indicative of localized stress-induced dissolution under a non-hydrostatic state of stress, separated by a clay parting which is believed to be the residuum of the dissolved rock. These structures are the most frequent deformation pattern in monomineralic rocks and thus provide important information about low temperature deformation and mass transfer. The intriguing roughness of stylolites can be used to assess amount of volume loss and paleo-stress directions, and to infer the destabilizing processes during pressure solution. But there is little agreement on how stylolites form and why these localized pressure solution patterns develop their characteristic roughness.rnNatural bedding parallel and vertical stylolites were studied in this work to obtain a quantitative description of the stylolite roughness and understand the governing processes during their formation. Adapting scaling approaches based on fractal principles it is demonstrated that stylolites show two self affine scaling regimes with roughness exponents of 1.1 and 0.5 for small and large length scales separated by a crossover length at the millimeter scale. Analysis of stylolites from various depths proved that this crossover length is a function of the stress field during formation, as analytically predicted. For bedding parallel stylolites the crossover length is a function of the normal stress on the interface, but vertical stylolites show a clear in-plane anisotropy of the crossover length owing to the fact that the in-plane stresses (σ2 and σ3) are dissimilar. Therefore stylolite roughness contains a signature of the stress field during formation.rnTo address the origin of stylolite roughness a combined microstructural (SEM/EBSD) and numerical approach is employed. Microstructural investigations of natural stylolites in limestones reveal that heterogeneities initially present in the host rock (clay particles, quartz grains) are responsible for the formation of the distinctive stylolite roughness. A two-dimensional numerical model, i.e. a discrete linear elastic lattice spring model, is used to investigate the roughness evolving from an initially flat fluid filled interface induced by heterogeneities in the matrix. This model generates rough interfaces with the same scaling properties as natural stylolites. Furthermore two coinciding crossover phenomena in space and in time exist that separate length and timescales for which the roughening is either balanced by surface or elastic energies. The roughness and growth exponents are independent of the size, amount and the dissolution rate of the heterogeneities. This allows to conclude that the location of asperities is determined by a polimict multi-scale quenched noise, while the roughening process is governed by inherent processes i.e. the transition from a surface to an elastic energy dominated regime.rn

Global modeling of pollutant transport and deposition from anthropogenic emission hot spots on global scale

Urban centers significantly contribute to anthropogenic air pollution, although they cover only a minor fraction of the Earth's land surface. Since the worldwide degree of urbanization is steadily increasing, the anthropogenic contribution to air pollution from urban centers is expected to become more substantial in future air quality assessments. The main objective of this thesis was to obtain a more profound insight in the dispersion and the deposition of aerosol particles from 46 individual major population centers (MPCs) as well as the regional and global influence on the atmospheric distribution of several aerosol types. For the first time, this was assessed in one model framework, for which the global model EMAC was applied with different representations of aerosol particles. First, in an approach with passive tracers and a setup in which the results depend only on the source location and the size and the solubility of the tracers, several metrics and a regional climate classification were used to quantify the major outflow pathways, both vertically and horizontally, and to compare the balance between pollution export away from and pollution build-up around the source points. Then in a more comprehensive approach, the anthropogenic emissions of key trace species were changed at the MPC locations to determine the cumulative impact of the MPC emissions on the atmospheric aerosol burdens of black carbon, particulate organic matter, sulfate, and nitrate. Ten different mono-modal passive aerosol tracers were continuously released at the same constant rate at each emission point. The results clearly showed that on average about five times more mass is advected quasi-horizontally at low levels than exported into the upper troposphere. The strength of the low-level export is mainly determined by the location of the source, while the vertical transport is mainly governed by the lifting potential and the solubility of the tracers. Similar to insoluble gas phase tracers, the low-level export of aerosol tracers is strongest at middle and high latitudes, while the regions of strongest vertical export differ between aerosol (temperate winter dry) and gas phase (tropics) tracers. The emitted mass fraction that is kept around MPCs is largest in regions where aerosol tracers have short lifetimes; this mass is also critical for assessing the impact on humans. However, the number of people who live in a strongly polluted region around urban centers depends more on the population density than on the size of the area which is affected by strong air pollution. Another major result was that fine aerosol particles (diameters smaller than 2.5 micrometer) from MPCs undergo substantial long-range transport, with about half of the emitted mass being deposited beyond 1000 km away from the source. In contrast to this diluted remote deposition, there are areas around the MPCs which experience high deposition rates, especially in regions which are frequently affected by heavy precipitation or are situated in poorly ventilated locations. Moreover, most MPC aerosol emissions are removed over land surfaces. In particular, forests experience more deposition from MPC pollutants than other land ecosystems. In addition, it was found that the generic treatment of aerosols has no substantial influence on the major conclusions drawn in this thesis. Moreover, in the more comprehensive approach, it was found that emissions of black carbon, particulate organic matter, sulfur dioxide, and nitrogen oxides from MPCs influence the atmospheric burden of various aerosol types very differently, with impacts generally being larger for secondary species, sulfate and nitrate, than for primary species, black carbon and particulate organic matter. While the changes in the burdens of sulfate, black carbon, and particulate organic matter show an almost linear response for changes in the emission strength, the formation of nitrate was found to be contingent upon many more factors, e.g., the abundance of sulfuric acid, than only upon the strength of the nitrogen oxide emissions. The generic tracer experiments were further extended to conduct the first risk assessment to obtain the cumulative risk of contamination from multiple nuclear reactor accidents on the global scale. For this, many factors had to be taken into account: the probability of major accidents, the cumulative deposition field of the radionuclide cesium-137, and a threshold value that defines contamination. By collecting the necessary data and after accounting for uncertainties, it was found that the risk is highest in western Europe, the eastern US, and in Japan, where on average contamination by major accidents is expected about every 50 years.

Untersuchung zum Entstehungsmechanismus von Smith-Purcell-Strahlung im Nahbereich mit einem 855 MeV Elektronenstrahl geringer Emittanz

Experimental investigations of visible Smith-Purcell-radiation with a micro-focused high relativistic electron beam (E=855 MeV) are presented in the near region, in which the electron beam grazes the surface of the grating. The radiation intensity was measured as a function of the angle of observation and of the distance between electron beam axis and the surface of the grating simultaneously for two different wavelengths (360 nm, 546 nm).In the experiments Smith-Purcell-radiation was identified by the measured angular distribution fulfilling the characteristic coherence condition. By the observed distance dependence of the intensity two components of Smith-Purcell-radiation could be separated: one component with the theoretical predicted interaction length hint, which is produced by electrons passing over the surface of the grating, and an additional component in the near region leading to a strong enhancement of the intensity, which is produced by electrons hitting the surface. To describe the intensity of the observed additional radiation component a simple model for optical grating transition radiation, caused by the electrons passing through the grating structure, is presented. Taking into account the simple scalar model, the results of a Monte-Carlo calculation show that the additional radiation component could be explained by optical grating transition radiation.

Wasserfreie, polymere Protonenleiter für Brennstoffzellen durch Immobilisierung von Imidazol

Es werden neuartige, polymere Protonenleiter vorgestellt die nach dem 'Konzept des polymergebunden Protonensolvens' realisiert wurden. Sie zeigen protonische Leitfähigkeit als intrinsische Eigenschaft, sodass keine zweite, flüssige Phase zur Protonenleitung nötig ist. Verwirklicht wurde das Konzept anhand von kammartigen Siloxanoligomeren und -polymeren, wobei Imidazol als Protonensolvens durch flexible Spacer kovalent an das Rückgrat gebunden ist. Durch Pfropfung mit imidazoltragenden Spacereinheiten wurden ferner Kieselgelnanopartikel oberflächenmodifiziert. Um die Auswirkungen der Immobilisierung von Imidazol auf die Leitfähigkeit zu untersuchen, wurden neben unterschiedlichen Molekulargewichten, die Verbindungen auch jeweils mit verschiedenen Spacerlängen synthetisiert. Die Materialien wurden umfassend charakterisiert und auf ihr thermisches Verhalten, Stabilität, Leitfähigkeit, Diffusion und dielektrisches Verhalten sowie auch nach Dotierung mit Säure untersucht. Thermisch stabil sind die Materialien bis ca. 200°C. Die Leitfähigkeiten betragen bis zu 1,5E-3 S/cm bei 160°C, welche aufgrund der Immobilisierung des Imidazols ausschließlich auf Strukturdiffusion zurückzuführen sind. Die Strukturdiffusion ist vergleichbar mit dem Grotthus-Mechanismus in Wasser und wird durch die lokale Mobilität der Imidazolmoleküle, d.h. durch die Glasübergangstemperatur des Systems bestimmt. Entsprechend wird das für Glasbildner typische Vogel-Tamman-Fulcher-Verhalten für alle untersuchten Transportprozesse gefunden. Die mit abnehmender Glasübergangstemperatur abnehmende mechanische Stabilität der Materialien kann, wie gezeigt ist, durch Compoundierung mit Kieselgelnanopartikeln entscheidend verbessert werden, was eine kostengünstige und aussichtsreiche Möglichkeit zur Herstellung von Membranen für Brennstoffzellen darstellt.

Monte-Carlo-Simulationen zum Phasenverhalten binärer Polymerbürsten

Diese Arbeit beschäftigt sich mit Strukturbildung im schlechten Lösungsmittel bei ein- und zweikomponentigen Polymerbürsten, bei denen Polymerketten durch Pfropfung am Substrat verankert sind. Solche Systeme zeigen laterale Strukturbildungen, aus denen sich interessante Anwendungen ergeben. Die Bewegung der Polymere erfolgt durch Monte Carlo-Simulationen im Kontinuum, die auf CBMC-Algorithmen sowie lokalen Monomerverschiebungen basieren. Eine neu entwickelte Variante des CBMC-Algorithmus erlaubt die Bewegung innerer Kettenteile, da der bisherige Algorithmus die Monomere in Nähe des Pfropfmonomers nicht gut relaxiert. Zur Untersuchung des Phasenverhaltens werden mehrere Analysemethoden entwickelt und angepasst: Dazu gehören die Minkowski-Maße zur Strukturuntersuchung binären Bürsten und die Pfropfkorrelationen zur Untersuchung des Einflusses von Pfropfmustern. Bei einkomponentigen Bürsten tritt die Strukturbildung nur beim schwach gepfropften System auf, dichte Pfropfungen führen zu geschlossenen Bürsten ohne laterale Struktur. Für den graduellen Übergang zwischen geschlossener und aufgerissener Bürste wird ein Temperaturbereich bestimmt, in dem der Übergang stattfindet. Der Einfluss des Pfropfmusters (Störung der Ausbildung einer langreichweitigen Ordnung) auf die Bürstenkonfiguration wird mit den Pfropfkorrelationen ausgewertet. Bei unregelmäßiger Pfropfung sind die gebildeten Strukturen größer als bei regelmäßiger Pfropfung und auch stabiler gegen höhere Temperaturen. Bei binären Systemen bilden sich Strukturen auch bei dichter Pfropfung aus. Zu den Parametern Temperatur, Pfropfdichte und Pfropfmuster kommt die Zusammensetzung der beiden Komponenten hinzu. So sind weitere Strukturen möglich, bei gleicher Häufigkeit der beiden Komponenten bilden sich streifenförmige, lamellare Muster, bei ungleicher Häufigkeit formt die Minoritätskomponente Cluster, die in der Majoritätskomponente eingebettet sind. Selbst bei gleichmäßig gepfropften Systemen bildet sich keine langreichweitige Ordnung aus. Auch bei binären Bürsten hat das Pfropfmuster großen Einfluss auf die Strukturbildung. Unregelmäßige Pfropfmuster führen schon bei höheren Temperaturen zur Trennung der Komponenten, die gebildeten Strukturen sind aber ungleichmäßiger und etwas größer als bei gleichmäßig gepfropften Systemen. Im Gegensatz zur self consistent field-Theorie berücksichtigen die Simulationen Fluktuationen in der Pfropfung und zeigen daher bessere Übereinstimmungen mit dem Experiment.

Polyphenylene dendrimers

The main goals of this work were the design, synthesis, and characterization of new functional polyphenylene dendrimers. Polyphenylene dendrimers are highly branched, monodisperse macromolecules consisting exclusively of benzene rings. They can be obtained in high yield by a repetitive Diels-Alder cycloaddition - deprotection protocol. Their shape-persistent dendritic scaffold allows to obtain nanoparticles with functional groups in defined relative orientation. In the first chapter polyphenylene dendrimers with a pyrene core are presented. The focus of the investigations was upon the shielding efficiency of dendritic shells of different generations upon the pyrene-functionality in the core. The herein presented materials combine high quantum efficiency, good solubility and improved film forming properties making them possible candidates for several applications in electronic devices. The defined functionalization of polyphenylene dendrimers often requires a great synthetic effort, since for every desired function the appropriate building block has to be synthesized. To overcome these disadvantages, a new functionalization concept based upon benzophenone precursors has been developed. This new concept has successfully been applied for the functionalization of the dendritic core, the dendrimer shell, and the dendrimer surface. To investigate the accessibility and reactivity of the embedded groups, many functions of different size and nature were introduced. Moreover, suitable precursors for the synthesis of dendrimer entrapped species, trityl cations, trityl radicals, and ketyl radical anions, were obtained. The combination of the synthetic protocols of core- and surface-functionalization resulted in a new type of functional molecules, highly interesting from the point of electron transfer processes. A polyphenylene dendron was used to arrange a triphenylamine donor and a perylene acceptor moiety in a defined spatial distance and orientation. The in-depth photophysical investigation of a first model compound is reported. The herein presented functionalized dendrimers are highly interesting as well from the point of view of fundamental research (looking into the optic and electronic properties of such unique shape persistent structures) as from the point of view of their potential application as tailor-made nanomaterials in the field of optoelectronics.

Synthese und Charakterisierung einer Hydrogelmatrix für die Multianalyt-Sensorik

Gegenstand und Ziel der vorliegenden Arbeit war die Synthese und Charakterisierung einer Hydrogelmatrix, welche für die Herstellung eines vielseitig verwendbaren Sensors, der mehrere Analyten (Proteine, DNA etc.) in hoher Verdünnung (c0 < 50 fM) aus kleinsten Probenmengen (Volumina <20 nl) schnell (t < 1 min) und parallel nachweisen kann, Verwendung finden soll. Der Fokus der Arbeit lag dabei in der Synthese und Charakterisierung von Copolymeren als Hydrogelmatrix, welche geeignetes temperaturabhängiges Verhalten zeigen. Die Copolymere wurden in eine dreidimensionale Netzwerkstruktur überführt und auf einer Goldoberfläche kovalent angebunden, um Delamination zu vermeiden und die Untersuchung mittels Oberflächenplasmonenresonanz-Spektroskopie (SPR) und Optischer Wellenleiter-Spektroskopie (OWS) zu erlauben. Weiterhin wurde das temperaturabhängige Verhalten der Polymernetzwerke in Wasser mittels optischen Messungen (SPR/OWS) untersucht, um Erkenntnisse über die Quell- und Kollabiereigenschaften des Hydrogels zu gewinnen. Um temperaturschaltbare Hydrogele herzustellen, wurden auf N-Isopropylacrylamid (NIPAAm) basierende Polymere synthetisiert. Es wurde sowohl die für Hydrogele übliche Methode der freien radikalischen Vernetzungspolymerisation in Wasser, wie eine neue, auf Benzophenoneinheiten basierende Syntheseroute, welche die freie radikalische Polymerisation in organischem Medium nutzt, verwendet. Die synthetisierten Polymere sind Copolymere aus N‑Isopropylacrylamid (NIPAAm) und 4-Methacryloyloxybenzophenon (MABP). NIPAAm ist dabei für das temperaturschaltbare Verhalten der Gele verantwortlich und MABP dient als Photovernetzer. Weitere Copolymere, die neben den genannten Monomeren noch andere Funktionen, wie z.B. ionische Gruppen oder Aktivesterfunktionen enthalten, wurden ebenfalls synthetisiert. Das temperaturabhängige Quellverhalten in Bezug auf die chemische Zusammensetzung wurde mit der Oberflächenplasmonenresonanz-Spektroskopie (SPR) und Optischen Wellenleiter-Spektroskopie (OWS) untersucht. Es zeigte sich, dass die Anwesenheit von Salz im Hydrogel (Natriumacrylat als Monomer, P4S) Inhomogenität, in Form eines Brechungsindexgradienten senkrecht zur Substratoberfläche, hervorruft. Dies ist nicht der Fall, wenn statt des Salzes die Säure (Methacrylsäure als Monomer, P4A) verwendet wird. Durch die Inhomogenität lassen sich die Filme mit dem Natriummethacrylat nicht mehr mit dem, üblicherweise zur Auswertung genutzten, Kastenmodell beschreiben. Die Anwendung der Wentzel-Kramers-Brillouin-Näherung (WKB) auf die Messdaten führt hingegen zu dem gewünschten Ergebnis. Man findet ein kastenähnliches Brechungsindexprofil für das Hydrogel mit der Säure (P4A) und ein Gradientenprofil für das Gel mit dem Salz (P4S). Letzteres ist nicht nur hydrophiler und insgesamt stärker gequollen, sondern ragt auch weiter in die überstehende Wasserphase hinein. Anhand eines säurehaltigen Hydrogels (P8A) konnte der quellungshemmende Einfluss von hohen Salzkonzentrationen gezeigt werden. Weiterhin wurde während des Quellvorgangs eine gewisse Anisotropie gefunden, die aber im vollständig gequollenen und vollständig kollabierten Zustand nicht mehr vorliegt. Anhand eines Hydrogels ohne ionisierbare Gruppen (P9) wurde die Reversibilität des Quell- und Kollabiervorgangs gezeigt. Bei einem Vergleich zwischen einem säurehaltigen Hydrogel (P8A, Quellgrad von 7,3) und einem ohne ionisierbare Gruppen (P9, Quellgrad von 6,1), hat die Anwesenheit der 8 mol% Säuregruppen eine leichte Verstärkung der Quellung um den Faktor 1,2 bewirkt. Rasterkraftmikroskopische Untersuchungen (AFM) an diesen beiden Hydrogelen im getrockneten Zustand, haben gezeigt, dass nach dem Quellen, Kollabieren und Trocknen bei beiden Gelen Porenstrukturen sehr unterschiedlicher Ausmaße vorliegen.

Biogenic emission of halocarbons

Within this doctoral thesis, biogenic emissions of several globally relevant halocarbons (methyl chloride, methyl bromide, methyl iodide, dibromomethane, chloroform and bromoform) have been investigated in different environments. An airborne study was focused on the tropical rainforest ecosystem, while shipborne measurements investigated naturally occurring oceanic plankton blooms. Laboratory experiments using dried plant material were made to elucidate abiotic production mechanisms occurring in organic matter. Airborne measurements over the tropical rainforest of Suriname and French Guyana (3 - 6 °N, 51 - 59 °W) revealed net fluxes of 9.5 (± 3.8 2σ) µg m-2 h-1 methyl chloride and 0.35 (± 0.15 2σ) µg m-2 h-1 chloroform emitted in the long dry season (October) 2005. An extrapolation of these numbers to all tropical forests helped to narrow down the range of the recently discovered and poorly quantified methyl chloride source from tropical ecosystems. The value for methyl chloride obtained (1.5 (± 0.6 2σ) Tg yr-1) affirms that the contribution of the tropical forest ecosystem is the major source in the global budget of methyl chloride. The extrapolated global net chloroform flux from tropical forests (56 (± 23 2σ) Gg yr-1) is of minor importance (5 - 10 %) compared to the global sources. A source of methyl bromide from this region could not be verified. The abiotic formation of methyl chloride and methyl bromide from dead plant material was tested in a laboratory study. The release from plant tissue representative of grassland, deciduous forest, agricultural areas and coastal salt marshes (hay, ash, tomato and saltwort) has been monitored. Incubations at different temperatures (25 - 50 °C) revealed significant emissions even at ambient temperature, and that the emissions increased exponentially with temperature. The strength of the emission was found to be additionally dependent on the availability of halide and the methoxyl group within the plant tissue. However, high water content in the plant material was found to inhibit methyl halide emissions. The abiotic nature of the reaction yielding methyl halides was confirmed by its high activation energy calculated via Arrhenius plots. Shipborne measurements of the atmospheric mixing ratios of methyl chloride, methyl bromide, methyl iodide, dibromomethane and bromoform have been conducted along a South Atlantic transect from the 27.01. - 05.02.2007 to characterize halocarbon emissions from a large-scale natural algae bloom encountered off the coast of Argentina. Mixing ratios of methyl chloride and methyl bromide were not significantly affected by the occurrence of the phytoplankton bloom. Emissions of methyl iodide, dibromomethane and bromoform showed pronounced mixing ratio variations, triggered by phytoplankton abundance. Methyl iodide was strongly correlated with dimethyl sulfide throughout the sampled region. A new technique combining satellite derived biomass marker (chlorophyll a) data with back trajectory analysis was successfully used to attribute variations in mixing ratios to air masses, which recently passed over areas of enhanced biological production.

Optical resonances of sphere-on-plane geometries

The optical resonances of metallic nanoparticles placed at nanometer distances from a metal plane were investigated. At certain wavelengths, these “sphere-on-plane” systems become resonant with the incident electromagnetic field and huge enhancements of the field are predicted localized in the small gaps created between the nanoparticle and the plane. An experimental architecture to fabricate sphere-on-plane systems was successfully achieved in which in addition to the commonly used alkanethiols, polyphenylene dendrimers were used as molecular spacers to separate the metallic nanoparticles from the metal planes. They allow for a defined nanoparticle-plane separation and some often are functionalized with a chromophore core which is therefore positioned exactly in the gap. The metal planes used in the system architecture consisted of evaporated thin films of gold or silver. Evaporated gold or silver films have a smooth interface with their substrate and a rougher top surface. To investigate the influence of surface roughness on the optical response of such a film, two gold films were prepared with a smooth and a rough side which were as similar as possible. Surface plasmons were excited in Kretschmann configuration both on the rough and on the smooth side. Their reflectivity could be well modeled by a single gold film for each individual measurement. The film has to be modeled as two layers with significantly different optical constants. The smooth side, although polycrystalline, had an optical response that was very similar to a monocrystalline surface while for the rough side the standard response of evaporated gold is retrieved. For investigations on thin non-absorbing dielectric films though, this heterogeneity introduces only a negligible error. To determine the resonant wavelength of the sphere-on-plane systems a strategy was developed which is based on multi-wavelength surface plasmon spectroscopy experiments in Kretschmann-configuration. The resonant behavior of the system lead to characteristic changes in the surface plasmon dispersion. A quantitative analysis was performed by calculating the polarisability per unit area /A treating the sphere-on-plane systems as an effective layer. This approach completely avoids the ambiguity in the determination of thickness and optical response of thin films in surface plasmon spectroscopy. Equal area densities of polarisable units yielded identical response irrespective of the thickness of the layer they are distributed in. The parameter range where the evaluation of surface plasmon data in terms of /A is applicable was determined for a typical experimental situation. It was shown that this analysis yields reasonable quantitative agreement with a simple theoretical model of the sphere-on-plane resonators and reproduces the results from standard extinction experiments having a higher information content and significantly increased signal-to-noise ratio. With the objective to acquire a better quantitative understanding of the dependence of the resonance wavelength on the geometry of the sphere-on-plane systems, different systems were fabricated in which the gold nanoparticle size, type of spacer and ambient medium were varied and the resonance wavelength of the system was determined. The gold nanoparticle radius was varied in the range from 10 nm to 80 nm. It could be shown that the polyphenylene dendrimers can be used as molecular spacers to fabricate systems which support gap resonances. The resonance wavelength of the systems could be tuned in the optical region between 550 nm and 800 nm. Based on a simple analytical model, a quantitative analysis was developed to relate the systems’ geometry with the resonant wavelength and surprisingly good agreement of this simple model with the experiment without any adjustable parameters was found. The key feature ascribed to sphere-on-plane systems is a very large electromagnetic field localized in volumes in the nanometer range. Experiments towards a quantitative understanding of the field enhancements taking place in the gap of the sphere-on-plane systems were done by monitoring the increase in fluorescence of a metal-supported monolayer of a dye-loaded dendrimer upon decoration of the surface with nanoparticles. The metal used (gold and silver), the colloid mean size and the surface roughness were varied. Large silver crystallites on evaporated silver surfaces lead to the most pronounced fluorescence enhancements in the order of 104. They constitute a very promising sample architecture for the study of field enhancements.

Thermal fluctuations and boundary conditions in the lattice Boltzmann method

The lattice Boltzmann method is a popular approach for simulating hydrodynamic interactions in soft matter and complex fluids. The solvent is represented on a discrete lattice whose nodes are populated by particle distributions that propagate on the discrete links between the nodes and undergo local collisions. On large length and time scales, the microdynamics leads to a hydrodynamic flow field that satisfies the Navier-Stokes equation. In this thesis, several extensions to the lattice Boltzmann method are developed. In complex fluids, for example suspensions, Brownian motion of the solutes is of paramount importance. However, it can not be simulated with the original lattice Boltzmann method because the dynamics is completely deterministic. It is possible, though, to introduce thermal fluctuations in order to reproduce the equations of fluctuating hydrodynamics. In this work, a generalized lattice gas model is used to systematically derive the fluctuating lattice Boltzmann equation from statistical mechanics principles. The stochastic part of the dynamics is interpreted as a Monte Carlo process, which is then required to satisfy the condition of detailed balance. This leads to an expression for the thermal fluctuations which implies that it is essential to thermalize all degrees of freedom of the system, including the kinetic modes. The new formalism guarantees that the fluctuating lattice Boltzmann equation is simultaneously consistent with both fluctuating hydrodynamics and statistical mechanics. This establishes a foundation for future extensions, such as the treatment of multi-phase and thermal flows. An important range of applications for the lattice Boltzmann method is formed by microfluidics. Fostered by the "lab-on-a-chip" paradigm, there is an increasing need for computer simulations which are able to complement the achievements of theory and experiment. Microfluidic systems are characterized by a large surface-to-volume ratio and, therefore, boundary conditions are of special relevance. On the microscale, the standard no-slip boundary condition used in hydrodynamics has to be replaced by a slip boundary condition. In this work, a boundary condition for lattice Boltzmann is constructed that allows the slip length to be tuned by a single model parameter. Furthermore, a conceptually new approach for constructing boundary conditions is explored, where the reduced symmetry at the boundary is explicitly incorporated into the lattice model. The lattice Boltzmann method is systematically extended to the reduced symmetry model. In the case of a Poiseuille flow in a plane channel, it is shown that a special choice of the collision operator is required to reproduce the correct flow profile. This systematic approach sheds light on the consequences of the reduced symmetry at the boundary and leads to a deeper understanding of boundary conditions in the lattice Boltzmann method. This can help to develop improved boundary conditions that lead to more accurate simulation results.

Pore structure and column efficiency of silica monoliths in high performance liquid chromatography (HPLC)

Five different methods were critically examined to characterize the pore structure of the silica monoliths. The mesopore characterization was performed using: a) the classical BJH method of nitrogen sorption data, which showed overestimated values in the mesopore distribution and was improved by using the NLDFT method, b) the ISEC method implementing the PPM and PNM models, which were especially developed for monolithic silicas, that contrary to the particulate supports, demonstrate the two inflection points in the ISEC curve, enabling the calculation of pore connectivity, a measure for the mass transfer kinetics in the mesopore network, c) the mercury porosimetry using a new recommended mercury contact angle values. rnThe results of the characterization of mesopores of monolithic silica columns by the three methods indicated that all methods were useful with respect to the pore size distribution by volume, but only the ISEC method with implemented PPM and PNM models gave the average pore size and distribution based on the number average and the pore connectivity values.rnThe characterization of the flow-through pore was performed by two different methods: a) the mercury porosimetry, which was used not only for average flow-through pore value estimation, but also the assessment of entrapment. It was found that the mass transfer from the flow-through pores to mesopores was not hindered in case of small sized flow-through pores with a narrow distribution, b) the liquid penetration where the average flow-through pore values were obtained via existing equations and improved by the additional methods developed according to Hagen-Poiseuille rules. The result was that not the flow-through pore size influences the column bock pressure, but the surface area to volume ratio of silica skeleton is most decisive. Thus the monolith with lowest ratio values will be the most permeable. rnThe flow-through pore characterization results obtained by mercury porosimetry and liquid permeability were compared with the ones from imaging and image analysis. All named methods enable a reliable characterization of the flow-through pore diameters for the monolithic silica columns, but special care should be taken about the chosen theoretical model.rnThe measured pore characterization parameters were then linked with the mass transfer properties of monolithic silica columns. As indicated by the ISEC results, no restrictions in mass transfer resistance were noticed in mesopores due to their high connectivity. The mercury porosimetry results also gave evidence that no restrictions occur for mass transfer from flow-through pores to mesopores in the small scaled silica monoliths with narrow distribution. rnThe prediction of the optimum regimes of the pore structural parameters for the given target parameters in HPLC separations was performed. It was found that a low mass transfer resistance in the mesopore volume is achieved when the nominal diameter of the number average size distribution of the mesopores is appr. an order of magnitude larger that the molecular radius of the analyte. The effective diffusion coefficient of an analyte molecule in the mesopore volume is strongly dependent on the value of the nominal pore diameter of the number averaged pore size distribution. The mesopore size has to be adapted to the molecular size of the analyte, in particular for peptides and proteins. rnThe study on flow-through pores of silica monoliths demonstrated that the surface to volume of the skeletons ratio and external porosity are decisive for the column efficiency. The latter is independent from the flow-through pore diameter. The flow-through pore characteristics by direct and indirect approaches were assessed and theoretical column efficiency curves were derived. The study showed that next to the surface to volume ratio, the total porosity and its distribution of the flow-through pores and mesopores have a substantial effect on the column plate number, especially as the extent of adsorption increases. The column efficiency is increasing with decreasing flow through pore diameter, decreasing with external porosity, and increasing with total porosity. Though this tendency has a limit due to heterogeneity of the studied monolithic samples. We found that the maximum efficiency of the studied monolithic research columns could be reached at a skeleton diameter of ~ 0.5 µm. Furthermore when the intention is to maximize the column efficiency, more homogeneous monoliths should be prepared.rn

Untersuchung der Struktur und Assemblierung des Lichtsammelkomplexes II höherer Pflanzen mittels elektronenparamagnetischer Resonanz (EPR)

Der Haupt-Lichtsammelkomplex (LHCII) des Photosyntheseapparates höherer Pflanzen gehört zu den häufigsten Membranproteinen der Erde. Seine Kristallstruktur ist bekannt. Das Apoprotein kann rekombinant in Escherichia coli überexprimiert und somit molekularbiologisch vielfältig verändert werden. In Detergenzlösung besitzt das denaturierte Protein die erstaunliche Fähigkeit, sich spontan zu funktionalen Protein-Pigment-Komplexen zu organisieren, welche strukturell nahezu identisch sind mit nativem LHCII. Der Faltungsprozess findet in vitro im Zeitbereich von Sekunden bis Minuten statt und ist abhängig von der Bindung der Cofaktoren Chlorophyll a und b sowie verschiedenen Carotinoiden.rn Diese Eigenschaften machen LHCII besonders geeignet für Strukturuntersuchungen mittels der elektronenparamagnetischen Resonanz (EPR)-Spektrokopie. Diese setzt eine punktspezifische Spinmarkierung des LHCII voraus, die in dieser Arbeit zunächst optimiert wurde. Einschließlich der Beiträge Anderer stand eine breite Auswahl von über 40 spinmarkierten Mutanten des LHCII bereit, einen N-terminalen „Cys walk“ eingeschlossen. Weder der hierfür notwendige Austausch einzelner Aminosäuren noch die Anknüpfung des Spinmarkers beeinträchtigten die Funktion des LHCII. Zudem konnte ein Protokoll zur Präparation heterogen spinmarkierter LHCII-Trimere entwickelt werden, also von Trimeren, die jeweils nur ein Monomer mit einer Spinmarkierung enthalten.rn Spinmarkierte Proben des Detergenz-solubilisierten LHCII wurden unter Verwendung verschiedener EPR-Techniken strukturell analysiert. Als besonders aussagekräftig erwies sich die Messung der Wasserzugänglichkeit einzelner Aminosäurepositionen anhand der Electron Spin Echo Envelope Modulation (ESEEM). In Kombination mit der etablierten Double Electron-Electron Resonance (DEER)-Technik zur Detektion von Abständen zwischen zwei Spinmarkern wurde der membranständige Kernbereich des LHCII in Lösung eingehend untersucht und strukturell der Kristallstruktur für sehr ähnlich befunden. Die Vermessung kristallographisch nicht erfasster Bereiche nahe dem N-Terminus offenbarte die schon früher detektierte Strukturdynamik der Domäne in Abhängigkeit des Oligomerisierungsgrades. Der neue, noch zu vervollständigende Datensatz aus Abstandsverteilungen und ESEEM-Wasserzugänglichkeiten monomerer wie trimerer Proben sollte in naher Zukunft die sehr genaue Modellierung der N-terminalen Domäne des LHCII ermöglichen.rn In einem weiteren Abschnitt der Arbeit wurde die Faltung des LHCII-Apoproteins bei der LHCII-Assemblierung in vitro untersucht. Vorausgegangene fluoreszenzspektroskopi-sche Arbeiten hatten gezeigt, dass die Bindung von Chlorophyll a und b in aufeinanderfolgenden Schritten im Zeitbereich von weniger als einer Minute bzw. mehreren Minuten erfolgten. Sowohl die Wasserzugänglichkeit einzelner Aminosäurepositionen als auch Spin-Spin-Abstände änderten sich in ähnlichen Zeitbereichen. Die Daten deuten darauf hin, dass die Ausbildung der mittleren Transmembran-Helix mit der schnelleren Chlorophyll-a-Bindung einhergeht, während sich die Superhelix aus den beiden anderen Transmembranhelices erst im langsameren Schritt, zusammen mit der Chlorophyll-b-Bindung, ausbildet.rn

Photochemie der Troposphäre in niedrigen und mittleren Breiten: Die Rolle von Konvektion

Ozon (O3) ist in der Atmosphäre ein wichtiges Oxidanz und Treibhausgas. Während die höchsten Konzentrationen in der Stratosphäre beobachtet werden und die vor der gefährlichen UV-Strahlung schützende Ozonschicht bilden, können sich signifikante Änderungen der Ozon-Konzentration in der Region der Tropopause auf das Klima der Erde auswirken. Des Weiteren ist Ozon eine der Hauptquellen für das Hydroxylradikal (OH) und nimmt damit entscheidend Einfluss auf die Oxidationskraft der Atmosphäre. Der konvektive Transport von Ozon und seinen Vorläufergasen aus Regionen nahe der Erdoberfläche in die freie Troposphäre beeinflusst das Budget dieser Spezies in der Tropopausenregion.rnDie Datengrundlage der Studie in der vorliegenden Arbeit basiert auf den flugzeuggetragenen Messkampagnen GABRIEL 2005 (Suriname, Südamerika) sowie HOOVER I 2006 und HOOVER II 2007 (beide in Europa). Mit dem zur Verfügung stehenden Datensatz wird das Ozonbudget in der freien, unbelasteten Hintergrundatmosphäre und in der durch hochreichende Konvektion gestörten, oberen Troposphäre untersucht. Anhand der auf in-situ Messungen von O3, NO, OH, HO2 und dem aktinischen Strahlungsfluss basierten Berechnung der Netto-Ozonproduktionsrate (NOPR) werden für das Messgebiet Ozontendenzen in der unbelasteten Troposphäre abgeleitet und mit Simulationen des globalen Chemie-Transport-Modells MATCH-MPIC verglichen. Mit Hilfe zweier Fallstudien in den Tropen in Südamerika und den mittleren Breiten in Europa werden die Auswirkungen von hochreichender Konvektion auf die obere Troposphäre quantifiziert.rnDie Ergebnisse zeigen für die Grenzschicht in niedrigen und mittleren Breiten eine eindeutige Tendenz zur Produktion von Ozon, was für den tropischen Regenwald in der Messregion nicht der allgemeinen Erwartung entsprach, nach der diese Region durch die Zerstörung von Ozon charakterisiert sein sollte. In der oberen Troposphäre ab etwa 7 km wird für die beiden Regionen eine leichte Tendenz zur Ozonproduktion beobachtet. Signifikante Unterschiede zeigen die Ergebnisse für die mittlere Troposphäre. Während die Tropen in dieser Region durch eine eindeutige Tendenz zur Zerstörung von Ozon charakterisiert sind, lässt sich über den mittleren Breiten zwar eine hohe photochemische Aktivität aber keine derart klare Tendenz feststellen. Die hohen Breiten zeichnen sich durch eine neutrale Troposphäre in Bezug auf die Ozontendenz aus und weisen kaum photochemische Aktivität auf. Der Vergleich dieser Ergebnisse mit dem MATCH-MPIC Modell zeigt in weiten Teilen der Messregionen eine grundlegende Übereinstimmung in der Tendenz zur Produktion oder Zerstörung von Ozon. Die absoluten Werte werden vom Modell aber generell unterschätzt. Signifikante Unterschiede zwischen in-situ Daten und Modellsimulationen werden in der Grenzschicht über dem tropischen Regenwald identifiziert.rnDer Einfluss der Konvektion ist durch eine signifikant erhöhte NOPR gekennzeichnet. In dieser Arbeit wird in den Tropen mit einem Median-Wert von 0.20 ppbv h−1 eine um den Faktor 3.6 erhöhte NOPR im Vergleich zur ungestörten oberen Troposphäre abgeschätzt. In den mittleren Breiten führt die um eine Größenordnung höhere NO-Konzentration zu einem Wert von 1.89 ppbv h−1, was einer Überhöhung um einen Faktor 6.5 im Vergleich zum ungestörten Zustand entspricht. Diese Ergebnisse zeigen für beide Regionen in der oberen Troposphäre eine erhöhte Ozonproduktion als Folge konvektiver Aktivität. rnrnHochreichende Konvektion ist zudem ein sehr effektiver Mechanismus für den Vertikaltransport aus der Grenzschicht in die obere Troposphäre. Die schnelle Hebung in konvektiven Wolken führt bei Spurengasen mit Quellen an der Erdoberfläche zu einer Erhöhung ihrer Konzentration in der oberen Troposphäre. Die hochgradig löslichen Spurenstoffe Formaldehyd (HCHO) und Wasserstoffperoxid (H2O2) sind wichtige Vorläufergase der HOx-Radikale. Es wird angenommen, dass sie aufgrund ihrer Löslichkeit in Gewitterwolken effektiv ausgewaschen werden.rnIn der vorliegenden Arbeit wird eine Fallstudie von hochreichender Konvektion im Rahmen des HOOVER II Projekts im Sommer 2007 analysiert. Am 19.07.2007 entwickelten sich am Nachmittag am Südostrand eines in nordöstlicher Richtung ziehenden mesoskaligen konvektiven Systems drei zunächst isolierte konvektive Zellen. Flugzeuggetragene Messungen in der Aus- und der Einströmregion einer dieser Gewitterzellen stellen einen exzellenten Datensatz bereit, um die Auswirkungen von hochreichender Konvektion auf die Verteilung verschiedener Spurengase in der oberen Troposphäre zu untersuchen. Der Vergleich der Konzentrationen von Kohlenstoffmonoxid (CO) und Methan (CH4) zwischen der oberen Troposphäre und der Grenzschicht deutet auf einen nahezu unverdünnten Transport dieser langlebigen Spezies in der konvektiven Zelle hin. Die Verhältnisse betragen (0.94±0.04) für CO und (0.99±0.01) für CH4. Für die löslichen Spezies HCHO und H2O2 beträgt dieses Verhältnis in der Ausströmregion (0.55±0.09) bzw. (0.61±0.08). Dies ist ein Indiz dafür, dass diese Spezies nicht so effektiv ausgewaschen werden wie angenommen. Zum besseren Verständnis des Einflusses der Konvektion auf die Budgets dieser Spezies in der oberen Troposphäre wurden im Rahmen dieser Arbeit Boxmodell-Studien für den Beitrag der photochemischen Produktion in der Ausströmregion durchgeführt, wobei die gemessenen Spezies und Photolysefrequenzen als Randbedingungen dienten. Aus den Budgetbetrachtungen für HCHO und H2O2 wird eine Auswascheffizienz von (67±24) % für HCHO und (41±18) % für H2O2 abgeschätzt. Das für H2O2 überraschende Ergebnis lässt darauf schließen, dass dieses Molekül in einer Gewitterwolke deutlich effektiver transportiert werden kann, als aufgrund seiner hohen Löslichkeit aus der Henry-Konstanten zu erwarten wäre. Das Ausgasen von gelöstem H2O2 beim Gefrieren eines Wolkentropfens, d.h. ein Retentionskoeffizient kleiner 1, ist ein möglicher Mechanismus, der zum beobachteten Mischungsverhältnis dieser löslichen Spezies in der Ausströmregion beitragen kann.