Confocal microscopy applied to the study of single entity fluorescence and light scattering

A sample scanning confocal optical microscope (SCOM) was designed and constructed in order to perform local measurements of fluorescence, light scattering and Raman scattering. This instrument allows to measure time resolved fluorescence, Raman scattering and light scattering from the same diffraction limited spot. Fluorescence from single molecules and light scattering from metallic nanoparticles can be studied. First, the electric field distribution in the focus of the SCOM was modelled. This enables the design of illumination modes for different purposes, such as the determination of the three-dimensional orientation of single chromophores. Second, a method for the calculation of the de-excitation rates of a chromophore was presented. This permits to compare different detection schemes and experimental geometries in order to optimize the collection of fluorescence photons. Both methods were combined to calculate the SCOM fluorescence signal of a chromophore in a general layered system. The fluorescence excitation and emission of single molecules through a thin gold film was investigated experimentally and modelled. It was demonstrated that, due to the mediation of surface plasmons, single molecule fluorescence near a thin gold film can be excited and detected with an epi-illumination scheme through the film. Single molecule fluorescence as close as 15nm to the gold film was studied in this manner. The fluorescence dynamics (fluorescence blinking and excited state lifetime) of single molecules was studied in the presence and in the absence of a nearby gold film in order to investigate the influence of the metal on the electronic transition rates. The trace-histogram and the autocorrelation methods for the analysis of single molecule fluorescence blinking were presented and compared via the analysis of Monte-Carlo simulated data. The nearby gold influences the total decay rate in agreement to theory. The gold presence produced no influence on the ISC rate from the excited state to the triplet but increased by a factor of 2 the transition rate from the triplet to the singlet ground state. The photoluminescence blinking of Zn0.42Cd0.58Se QDs on glass and ITO substrates was investigated experimentally as a function of the excitation power (P) and modelled via Monte-Carlo simulations. At low P, it was observed that the probability of a certain on- or off-time follows a negative power-law with exponent near to 1.6. As P increased, the on-time fraction reduced on both substrates whereas the off-times did not change. A weak residual memory effect between consecutive on-times and consecutive off-times was observed but not between an on-time and the adjacent off-time. All of this suggests the presence of two independent mechanisms governing the lifetimes of the on- and off-states. The simulated data showed Poisson-distributed off- and on-intensities, demonstrating that the observed non-Poissonian on-intensity distribution of the QDs is not a product of the underlying power-law probability and that the blinking of QDs occurs between a non-emitting off-state and a distribution of emitting on-states with different intensities. All the experimentally observed photo-induced effects could be accounted for by introducing a characteristic lifetime tPI of the on-state in the simulations. The QDs on glass presented a tPI proportional to P-1 suggesting the presence of a one-photon process. Light scattering images and spectra of colloidal and C-shaped gold nano-particles were acquired. The minimum size of a metallic scatterer detectable with the SCOM lies around 20 nm.

Functionalized surfaces and surface functionalization of nanomaterials

Nature leads, we follow. But nanotechnologists are in hot pursuit, in designing controllable structures that can mimic naturally occurring and artificially synthesized materials on a common platform. The supramolecular chemistry concerns the investigation of nature principles to produce fascinating complexed and functional molecular assemblies, as well as the utilization of these principles to generate novel devices and materials, potentially useful for sensing, catalysis, transport and other applications in medical or engineering science. The work presented in this thesis is a compilation of different synthetic methods to achieve inorganic-organic hybrid nanomaterials. Silicatein, a protein enzyme, which acts both as a catalyst and template for the formation of silica needles in marine sponges, has been used for the biosynthesis of semiconductor metal oxides on surfaces. Silicatein was immobilized on gold (111) surfaces using alkane thiol, as well as on a novel self-assembly of NTA on top of a “cushion” of reactive ester polymer has been successfully employed to make functionalised surfaces. The immobilization of silicatein on surfaces was monitored by surface plasmon spectroscopy, atomic force microscopy and confocal laser scanning microscopy. Surface bound silicatein retains its biocatalytic activity, which was demonstrated by monitoring its hydrocatalytic activity to catalyse the synthesis of biosilica, biotitania, and biozirconia. The synthesis of semiconductor metal oxides was characterized using scanning electron microscopy. This hydrolytic biocatalyst is used to synthesize the gold nanoparticles. The gold nanoparticles are formed by reduction of tetrachloroaurate, AuCl4-, by the action of sulfhydryl groups hidden below the surface groups of the protein. The resulting gold nanoparticles which are stabilized by surface bound silicatein further aggregate to form Au nanocrystals. The shape of the nanocrystals obtained by using recombinant silicatein is controlled through chiral induction by the protein during the nucleation of the nanocrystals. As an extension of this work, TiO2 nanowires were functionalized using polymeric ligand which incorporates the nitrilotriacetic acid (NTA) linker in the back bone to immobilize His-tagged silicatein onto the TiO2 nanowires. The surface bound protein not only retains its original hydrolytic properties, but also acts as a reductant for AuCl4- in the synthesis of hybrid TiO2/silicatein/Au nanocomposites. Functionalized, monocrystalline rutile TiO2 nanorods were prepared from TiCl4 in aqueous solution in the presence of dopamine. The surface bound organic ligand controls the morphology as well as the crystallinity and the phase selection of TiO2. The surface amine groups can be tailored further with functional molecules such as dyes. As an example, this surface functionality is used for the covalent binding of a fluorescent dye,4-chloro-7- nitrobenzylurazene (NBD) to the TiO2 nanorods. The polymeric ligands have been used successfully for the in-situ and post-functionalization of TiO2 nanoparticles. Besides to chelating dopamine anchor group the multifunctional ligand system presented here incorporates a modifier molecule which allows the binding of functional molecules (here the dyes pyrene, NBD, and Texas Red) as well as additional entities which allow tailoring the solubility of inorganic nanocrystals in different solvents. A novel method for the surface functionalization of fullerene-type MoS2 nanoparticles and subsequently binding these nanoparticles onto TiO2 nanowires has been reported using polymeric ligands. The procedure involves the complexation of IF-MoS2 with a combination of Ni2+ via an umbrella-type nitrilotriacetic acid (NTA) and anchoring them to the sidewalls of TiO2 nanowires utilizing the hydroxyl groups of dopamine present in the main contents of polymeric ligand. A convenient method for the synthesis of Au/CdS nanocomposites has been presented, which were achieved through the novel method of thiol functionalization of gold colloids. The thermodynamically most stable phase of ZrO2 (cubic) has been obtained at much lower temperature (180°C). These nanoparticles are highly blue fluorescent, with a high surface area.

High resolution study of local stress inside alumina - micro mechanical analysis using laser scanning confocal microscope

The aim of this work is to measure the stress inside a hard micro object under extreme compression. To measure the internal stress, we compressed ruby spheres (a-Al2O3: Cr3+, 150 µm diameter) between two sapphire plates. Ruby fluorescence spectrum shifts to longer wavelengths under compression and can be related to the internal stress by a conversion coefficient. A confocal laser scanning microscope was used to excite and collect fluorescence at desired local spots inside the ruby sphere with spatial resolution of about 1 µm3. Under static external loads, the stress distribution within the center plane of the ruby sphere was measured directly for the first time. The result agreed to Hertz’s law. The stress across the contact area showed a hemispherical profile. The measured contact radius was in accord with the calculation by Hertz’s equation. Stress-load curves showed spike-like decrease after entering non-elastic phase, indicating the formation and coalescence of microcracks, which led to relaxing of stress. In the vicinity of the contact area luminescence spectra with multiple peaks were observed. This indicated the presence of domains of different stress, which were mechanically decoupled. Repeated loading cycles were applied to study the fatigue of ruby at the contact region. Progressive fatigue was observed when the load exceeded 1 N. As long as the load did not exceed 2 N stress-load curves were still continuous and could be described by Hertz’s law with a reduced Young’s modulus. Once the load exceeded 2 N, periodical spike-like decreases of the stress could be observed, implying a “memory effect” under repeated loading cycles. Vibration loading with higher frequencies was applied by a piezo. Redistributions of intensity on the fluorescence spectra were observed and it was attributed to the repopulation of the micro domains of different elasticity. Two stages of under vibration loading were suggested. In the first stage continuous damage carried on until certain limit, by which the second stage, e.g. breakage, followed in a discontinuous manner.

Design, synthesis and application of ultrastable rylene dyes for fluorescent labeling of biomolecules

Studies of organic fluorescent dyes are experiencing a renaissance related to the increasing demands posed by new microscopy techniques for high resolution and high sensitivity. While in the last decade single molecule equipment and methodology has significantly advanced and in some cases reached theoretical limits (e.g. detectors approaching unity quantum yields) unstable emission from chromophores and photobleaching become more and more the bottleneck of the advancement and spreading of single-molecule fluorescence studies. The main goal of this work was the synthesis of fluorophores that are water-soluble, highly fluorescent in an aqueous environment, have a reactive group for attachment to a biomolecule and posses exceptional photostability. An approach towards highly fluorescent, water-soluble and monofunctional perylene-3,4,9,10-tetracarboxdiimide and terrylene-3,4:11,12-tetra carboxidiimide chromophores was presented. A new synthetic strategy for the desymmetrization of perylenetetracarboximides was elaborated; water-solubility was accomplished by introducing sulfonyl substituents in the phenoxy ring. Two strategies have been followed relying on either non-specific or site specific labeling. For this purpose a series of new water-soluble monofunctional perylene and terrylene dyes, bearing amine or carboxy group were prepared. The reactivity and photophysical properties of these new chromophores were studied in aqueous medium. The most suitable chromophores were further derivatized with amine or thiol reactive groups, suitable for chemical modification of proteins. The performance of the new fluorescent probes was assessed by single molecule enzyme tracking, in this case phospholipase acting on phospholipid supported layers. Phospholipase-1 (PLA-1) was labeled with N-hydroxysuccinimide ester functionalized perylene and terrylene derivatives. The purification of the conjugates was accomplished by novel convenient procedure for the removal of unreacted dye from labeled enzymes, which involves capturing excess dye with a solid support. This novel strategy for purification of bioconjugates allows convenient and fast separation of labeled proteins without the need for performing time consuming chromatographic or electrophoretic purification steps. The outstanding photostability of the dyes and, associated therewith, the extended survival times under strong illumination conditions allow a complete characterization of enzyme action on its natural substrates and even connecting enzyme mobility to catalytic activity. For site-specific attachment of the rylene dyes to proteins the chromophores were functionalized with thioesters or nitrilotriacetic acid groups. This allowed attachment of the emitters to the N-terminus of proteins by native chemical ligation or complexation with His-tagged polypeptides at the N- or C-termini, respectively. The synthesis of a water-soluble perylenebis (dicarboximide) functionalized with a thioester group was presented. This chromophore exhibits an exceptional photostability and a functional unit for site-specific labeling of proteins. The suitability of the fluorophore as a covalent label was demonstrated via native chemical ligation with protein containing N-terminal cystein residue. We exploited also oligohisitidine sequences as recognition elements for site-selective labeling. The synthesis of a new water-soluble perylene chromophore, containing a nitrilotriacetic acid functional group was demonstrated, using solution-phase and solid-phase approaches. This chromophore combines the exceptional photophysical properties of the rylene dyes and a recognition unit for site-specific labeling of proteins. An important feature of the label is the unchanged emission of the dye upon complexation with nickel ions.

Oligomerisation, localisation and interaction of the sensor histidine kinases DcuS and CitA in Escherichia coli

The two-component system DcuSR of Escherichia coli regulates gene expression of anaerobic fumarate respiration and aerobic C4-dicarboxylate uptake. C4-dicarboxylates and citrate are perceived by the periplasmic domain of the membrane-integral sensor histidine kinase DcuS. The signal is transduced across the membrane by phosphorylation of DcuS and of the response regulator DcuR, resulting in activation of DcuR and transcription of the target genes.rnIn this work, the oligomerisation of full-length DcuS was studied in vivo and in vitro. DcuS was genetically fused to derivatives of the green fluorescent protein (GFP), enabling fluorescence resonance energy transfer (FRET) measurements to detect protein-protein interactions in vivo. FRET measurements were also performed with purified His6-DcuS after labelling with fluorescent dyes and reconstitution into liposomes to study oligomerisation of DcuS in vitro. In vitro and in vivo fluorescence resonance energy transfer showed the presence of oligomeric DcuS in the membrane, which was independent of the presence of effector. Chemical crosslinking experiments allowed clear-cut evaluation of the oligomeric state of DcuS. The results showed that detergent-solubilised His6-DcuS was mainly monomeric and demonstrated the presence of tetrameric DcuS in proteoliposomes and in bacterial membranes.rnThe sensor histidine kinase CitA is part of the two-component system CitAB of E. coli, which is structurally related to DcuSR. CitAB regulates gene expression of citrate fermentation in response to external citrate. The sensor kinases DcuS and CitA were fused with an enhanced variant of the yellow fluorescent protein (YFP) and expressed in E. coli under the control of an arabinose-inducible promoter. The subcellular localisation of DcuS-YFP and CitA-YFP within the cell membrane was studied by means of confocal laser fluorescence microscopy. Both fusion proteins were found to accumulate at the cell poles. The polar accumulation was slightly increased in the presence of the stimulus fumarate or citrate, respectively, but independent of the expression level of the fusion proteins. Cell fractionation demonstrated that polar accumulation was not related to inclusion bodies formation. The degree of polar localisation of DcuS-YFP was similar to that of the well-characterised methyl-accepting chemotaxis proteins (MCPs), but independent of their presence. To enable further investigations on the function of the polar localisation of DcuS under physiological conditions, the sensor kinase was genetically fused to the flavin-based fluorescent protein Bs2 which shows fluorescence under aerobic and anaerobic conditions. The resulting dcuS-bs2 gene fusion was inserted into the chromosome of various E. coli strains.rnFurthermore, a protein-protein interaction between the related sensor histidine kinases DcuS and CitA, regulating common metabolic pathways, was detected via expression studies under anaerobic conditions in the presence of citrate and by in vivo FRET measurements.

Einzelmolekülspektroskopie an einer homologen Reihe von Rylendiimiden und an einem bichromophoren Modellsystem für elektronischen Energietransfer

In dieser Arbeit wurden Untersuchungen zur Fluoreszenzdynamik und zum Mechanismus des Photobleichens einzelner Farbstoffmoleküle einer homologen Reihe von Rylentetracarbonsäurediimiden durchgeführt. Mit der Erweiterung des elektronischen π-Systems verringert sich die HOMO/LUMO-Energiedifferenz, so dass strahlungslose Relaxationsprozesse gemäß des Energielückengesetzes zunehmen. Die konfokale Einzelmolekülspektroskopie in Kombination mit zeitkorrelierter Einzelphotonenzählung ermöglicht es, Fluktuationen der inneren Konversionsrate zu detektieren. Der limitierende Faktor jedes Einzelmolekülexperiments ist die Photostabilität der Moleküle. Für die homologe Reihe konnten mindestens zwei Photobleichmechanismen identifiziert werden. Wenn Singulett-Sauerstoff durch Selbstsensibilisierung erzeugt werden kann, ist unter Luft die Photooxidation der wahrscheinlichste Mechanismus. Unter Ausschluss von Luftsauerstoff spielt die Bildung langlebiger Dunkelzustände eine entscheidende Rolle, die bevorzugt über höher angeregte Triplett- und Singulett-Zustände abläuft. Es wird angenommen, dass es sich hierbei um einen reversiblen Ionisierungsprozess handelt, bei dem das Radikal-Kation der Rylendiimide gebildet wird. Es konnte gezeigt werden, dass durch eine geeignete Wahl der Anregungsbedingungen die Dunkelzustandspopulierung verhindert und zugleich die Photostabilität der Fluorophore deutlich erhöht wird. Durch die Verknüpfung der beiden niedrigsten Homologen erhält man ein Donor-Akzeptor-Modellsystem, bei dem die Anregungsenergie mit hoher Effizienz vom Donor- auf den Akzeptor-Chromophor übertragen wird. In der Fluoreszenz einzelner Bichromophore wurden bei selektiver Anregung des Donors kollektive Auszeiten beobachtet, die durch effiziente Singulett-Triplett-Annihilation verursacht werden.

Photonen-Aufkonversion in Nanokapseln

Die vorliegende Dissertation zeigt eine erfolgreiche Verknüpfung der Triplett-Triplett-Annihilations-Aufkonversion (TTA-UC) mit möglichen biologischen Anwendungen. Die Grundlage für solche Anwendungen ist ein Transfer der TTA-UC aus seinem üblicherweise verwendeten organischen Medium in eine wässrige Umgebung. Um diesen Transfer zu realisieren, wurden, unter Anwendung der Technik des Miniemulsionsprozesses, in Wasser dispergierte Nanokapseln herstellt. Der Kern dieser Nanokapseln besteht aus einem flüssigen hydrophoben Medium (meist Hexadekan oder Phenylheptadekan), in dem die zur TTA-UC notwendigen Farbstoffe gelöst sind. Dieser flüssige Kern ist vollständig von einer festen Polymerhülle umschlossen und somit isoliert von seiner wässrigen Umgebung. Es wurden insgesamt drei Generationen solcher Nanokapseln hergestellt, die sich hauptsächlich im Herstellungsprozess, aber auch beim Material von Kern und Hülle unterscheiden. Mittels dieser Variationen konnten die Nanokapseln in Bezug auf Effizienz, Anregungswellenlänge und Sauerstoffempfindlichkeit optimiert werden. Bei der ersten Generation wurde die radikalische Miniemulsionspolymerisation zur Kapselbildung verwendet. Die zweite Generation wurde durch die Kombination des Lösungsmittelverdampfungsprozesses mit dem Miniemulsionsprozess entwickelt und liefert somit eine alternative Möglichkeit der Kapselbildung unter milden Reaktionsbedingungen, was eine uneingeschränkte Auswahl der UC-Farbstoffpaare ermöglicht. Durch den Einsatz unterschiedlicher Sensitizer konnte die Anregungswellenlänge der TTA-UC in den roten und in den nahen Infrarot-Bereich des sichtbaren Spektrums verschoben werden. Diese Verschiebung ist im biologischen Anwendungsbereich von enormer Bedeutung, da dort eine Überlappung mit dem natürlichen optischen Fenster von menschlicher Haut und Gewebe stattfindet. Dies reduziert die Streuung der Anregungsquelle im zu untersuchende Medium und ermöglicht hohe Eindringtiefen. Mit den Kapseln der zweiten Generation wurde zum ersten Mal TTA-UC in lebenden HeLa-Zellen (Krebszellen) und MSCs (Mesenchymale Stammzellen) nachgewiesen. Die verzögerte Fluoreszenz aus den Zellen wurde mit biologischen Standardverfahren, sowohl mit der Durchflusszytometrie (FACS) als auch am cLSM nachgewiesen. Besondere Vorteile gegenüber direkter Fluoreszenz konnten bei der Bildgebung von Zellen erreicht werden. Die relativ energiearme Anregungswellenlänge und die dazu anti-Stokes verschobene, detektierte verzögerte UC-Fluoreszenz lieferte eine bessere Bildqualität und eine sehr geringe Phototoxizität der Zellen. Die Kapseln der dritten Generation zeichnen sich durch ihre anorganische, tetraedrisch verknüpfte SiO2-Hülle aus und wurden mittels einer Grenzflächenreaktion (Sol-Gel-Prozess) in Miniemulsion hergestellt. Diese Kapseln weisen im Vergleich zu den Polymernanokapseln eine bessere UC-Effizienz auf und sind zusätzlich stabiler und robuster.

Towards antibody-mediated targeting of dendritic cells for cancer immunotherapy with multivalent polymer-antigen conjugates

Der Fokus dieser Arbeit lag auf der definierten Synthese multifunktioneller Polymer-Konjugate zur Anwendung in der Krebs-Immunotherapie. Durch gezielte Variation der Kon-jugationsbedingungen wurde Zusammensetzung, Größe und Aggregationsverhalten in Zell-medium sowie in humanem Serum untersucht. Nach definierter physikalisch-chemischer Charakterisierung wurde dann die induzierte Antigen-Präsentation zur Aktivierung der T-Zellproliferation analysiert.rnDafür wurden zwei verschiedene polymere Carrier-Systeme gewählt, lineares Poly-L-lysin und eine Polylysinbürste (PLL-Bürste). Es wird vermutet, dass die PLL-Bürste aufgrund der anisotropen Form eine bessere Verteilung im Körper und eine verlängerte Zirkulationsdauer zeigen wird. Die zu konjugierenden biologisch aktiven Komponenten waren der antiDEC205-Antikörper (aDEC205) für die gezielte Adressierung CD8-positiver dendritischer Zellen (DC), ein Ovalbumin (OVA)-spezifisches Antigen mit der Kernsequenz SIINFEKL für die Spezifität der Immunantwort gegen Krebszellen, die dieses Antigen tragen, und ein immunaktivieren-der TLR9-Ligand, CpG1826. Die Effizienz dieses Konjugates dendritische Zellen zu aktivieren, welche wiederum eine Immunantwort gegen OVA-exprimierende Krebszellen induzieren, wurde durch die Konjugation aller Komponenten am identischen Trägermolekül deutlich höher erwartet.rnLineares Poly-L-lysin diente als Modellsystem um die Konjugationschemie zu etablieren und dann auf die zylindrische Polylysinbürste zu übertragen. Anhand dieser polymeren Träger wurde das Verhalten der verschiedenen Topologien des Knäuels und der Bürste im Hinblick auf den Einfluss struktureller Unterschiede sowohl auf Konjugationsreaktionen als auch auf das in situ und in vitro Verhalten untersucht.rnFluoreszenzmarkiertes Antigen und der CpG Aktivator konnten jeweils aufgrund einer Thiol-Modifizierung an die Thiol-reaktive Maleimidgruppe des heterobifunktionellen Linkers Sulfo-SMCC an PLL-AlexaFluor48 konjugiert werden. Anschließend wurde aDEC205-AlexaFluor647 an PLL gekoppelt, entweder durch Schiff Base-Reaktion des oxidierten Antikörpers mit PLL und anschließender Reduzierung oder durch Click-Reaktion des PEG-Azids modifizierten An-tikörpers mit Dicyclobenzylcyclooctin (DIBO)-funktionalisiertem PLL. Die Konjugation der biologisch aktiven Komponenten wurde mit Durchflusszytometrie (FACS) und konfokaler Laser Scanning Mikroskopie (CLSM) untersucht und die Zusammensetzung des Konjugatesrnmittels UV/Vis-Spektroskopie bestimmt. Die PLL-Bürste alleine zeigte eine hohe Zytotoxizität bei HeLa und JAWS II Zelllinien, wohingegen lineares PLL und PLL-Konjugate sowie die PLL Bürsten-Konjugate keine ausgeprägte Zytotoxizität aufwiesen. Die Polymer-Konjugate wie-sen keine Aggregation in Zellmedium oder humanem Serum auf, was mittels winkelabhängi-ger dynamischer Lichtstreuung bestimmt wurde. CLSM Aufnahmen zeigten Kolokalisation der an die einzelnen Komponenten gebundenen Fluoreszenzfarbstoffe in dendritischen Zel-len, was die erfolgreiche Konjugation und Internalisierung der Konjugate in die Zellen bele-gen konnte. FACS Messungen ergaben eine geringfügig erhöhte Aufnahme des adressierten PLL-Antigen-Antikörper-Konjugates verglichen mit dem PLL-Antigen-Konjugat. Experimente mit dem „Specific Hybridization Internalization Sensor“ (SHIP) zeigten jedoch nur Aufnahme der PLL-Konjugate in CD8+ unreife DC, nicht in reife DC, die nicht mehr unspezifisch, sondern nur noch über Rezeptoren internalisieren. Dies bewies die unspezifische Aufnahme des Kon-jugates, da Antikörper-Konjugation keine Rezeptor-vermittelte Endozytose in reife DC indu-zieren konnte. T-Zell-Proliferationsassays ergaben eine Aktivierung von CD8+ T-Zellen indu-ziert durch Antigen-tragende Konjugate, wohingegen Konjugate ohne Antigen als Negativ-kontrollen dienten und keine T-Zell-Proliferation erzielten. Es konnte jedoch kein Unter-schied zwischen adressierten und nicht adressierten Konjugaten aufgrund der unspezifischen Aufnahme durch das Polymer beobachtet werden. Lösliches SIINFEKL alleine bewirkte schon bei geringeren Konzentrationen eine T-Zell-Proliferation.rnEs war somit möglich, drei biologischen Komponenten an einen polymeren Träger zu konju-gieren und diese Konjugate im Hinblick auf Zusammensetzung, Größe, Internalisierung in dendritische Zellen und Aktivierung der T-Zell-Proliferation zu untersuchen. Außerdem wur-de die Konjugationschemie erfolgreich von dem Modellsystem des linearen PLL auf die PLL-Bürste übertragen. Die Polymer-Konjugate werde unspezifisch in DC aufgenommen und in-duzieren T-Zellproliferation, die mit Antigen-Präsentationsassays nachgewiesen wird. Es konnte jedoch durch Konjugation des Antikörpers keine Rezeptor-vermittelte Aufnahme in CD8+ DC erzielt werden.rnDiese Studien stellen einen erfolgsversprechenden ersten Schritt zur Entwicklung neuer Na-nomaterialien für die Anwendung in Krebs-Immuntherapie dar.

Diffusion in heterogeneous systems studied by laser scanning confocal microscopy and fluorescence correlation spectroscopy

Understanding and controlling the mechanism of the diffusion of small molecules, macromolecules and nanoparticles in heterogeneous environments is of paramount fundamental and technological importance. The aim of the thesis is to show, how by studying the tracer diffusion in complex systems, one can obtain information about the tracer itself, and the system where the tracer is diffusing. rnIn the first part of my thesis I will introduce the Fluorescence Correlation Spectroscopy (FCS) which is a powerful tool to investigate the diffusion of fluorescent species in various environments. By using the main advantage of FCS namely the very small probing volume (<1µm3) I was able to track the kinetics of phase separation in polymer blends at late stages by looking on the molecular tracer diffusion in individual domains of the heterogeneous structure of the blend. The phase separation process at intermediate stages was monitored with laser scanning confocal microscopy (LSCM) in real time providing images of droplet coalescence and growth. rnIn a further project described in my thesis I will show that even when the length scale of the heterogeneities becomes smaller than the FCS probing volume one can still obtain important microscopic information by studying small tracer diffusion. To do so, I will introduce a system of star shaped polymer solutions and will demonstrate that the mobility of small molecular tracers on microscopic level is nearly not affected by the transition of the polymer system to a “glassy” macroscopic state. rnIn the last part of the thesis I will introduce and describe a new stimuli responsive system which I have developed, that combines two levels of nanoporosity. The system is based on poly-N-isopropylacrylamide (PNIPAM) and silica inverse opals (iOpals), and allows controlling the diffusion of tracer molecules. rn

Wet and dry model granulates under mechanical load : a confocal microscopy study

Granular matter, also known as bulk solids, consists of discrete particles with sizes between micrometers and meters. They are present in many industrial applications as well as daily life, like in food processing, pharmaceutics or in the oil and mining industry. When handling granular matter the bulk solids are stored, mixed, conveyed or filtered. These techniques are based on observations in macroscopic experiments, i.e. rheological examinations of the bulk properties. Despite the amply investigations of bulk mechanics, the relation between single particle motion and macroscopic behavior is still not well understood. For exploring the microscopic properties on a single particle level, 3D imaging techniques are required.rnThe objective of this work was the investigation of single particle motions in a bulk system in 3D under an external mechanical load, i.e. compression and shear. During the mechanical load the structural and dynamical properties of these systems were examined with confocal microscopy. Therefor new granular model systems in the wet and dry state were designed and prepared. As the particles are solid bodies, their motion is described by six degrees of freedom. To explore their entire motion with all degrees of freedom, a technique to visualize the rotation of spherical micrometer sized particles in 3D was developed. rnOne of the foci during this dissertation was a model system for dry cohesive granular matter. In such systems the particle motion during a compression of the granular matter was investigated. In general the rotation of single particles was the more sensitive parameter compared to the translation. In regions with large structural changes the rotation had an earlier onset than the translation. In granular systems under shear, shear dilatation and shear zone formation were observed. Globally the granular sediments showed a shear behavior, which was known already from classical shear experiments, for example with Jenike cells. Locally the shear zone formation was enhanced, when near the applied load a pre-diluted region existed. In regions with constant volume fraction a mixing between the different particle layers occurred. In particular an exchange of particles between the current flowing region and the non-flowing region was observed. rnThe second focus was on model systems for wet granular matter, where an additional binding liquid is added to the particle suspension. To examine the 3D structure of the binding liquid on the micrometer scale independently from the particles, a second illumination and detection beam path was implemented. In shear and compression experiments of wet clusters and bulk systems completely different dynamics compared to dry cohesive models systems occured. In a Pickering emulsion-like system large structural changes predominantly occurred in the local environment of binding liquid droplets. These large local structural changes were due to an energy interplay between the energy stored in the binding droplet during its deformation and the binding energy of particles at the droplet interface. rnConfocal microscopy in combination with nanoindentation gave new insights into the single particle motions and dynamics of granular systems under a mechanical load. These novel experimental results can help to improve the understanding of the relationship between bulk properties of granular matter, such as volume fraction or yield stress and the dynamics on a single particle level.rnrn

Enzyme tRNA interaction and (t)RNA conformation probed via environmentally sensitive cyanine dyes

Nukleosidmodifikationen beeinflussen Dynamik und Konformation von RNArnund sind epigenetisch wirksam. Wenig verstanden sind konformationelle Dynamik und enzymatische Erkennung von tRNA, sowie der Einfluss des mutmaßlichen kovalenten Inhibitors 5-Fluorouridine (5FU) auf Y Synthasen, die Pseudouridin (Y) erzeugen. Frühere Arbeiten nutzten mit den Fluorophoren Cy3 und Cy5rnmarkierte tRNA, um diese Fragen zu adressieren.rnDie vorliegende Arbeit weitet Cy3-Cy5-Markierung auf Hefe tRNArnPhernaus undrnnutzt Thermophorese und fortschrittliche Fluoreszenzspektroskopie. In der Thermophorese zeigte sich eine hohe Toleranz gegenüber Fluoreszenzmarkierung beirngleichzeitiger Erhöhung der Cy5 Fluoreszenz durch Enzymbindung. Zudem konnte die Konformation verschiedener Mutanten human mitochondrialer tRNArnLysrnund die Bindung von SAM durch SAM-I Riboswitch RNA untersucht werden.rnUm etwaige Unterschiede in der Interaktion von Y55 Synthase TruB mit Cy5-gelabelter U55- bzw. 5FU55-tRNA aufzudecken, wurde eine Kombination ausrnThermophorese, zeit- und polarisationsaufgelöster Fluoreszenzspektroskopie undrn’gel shift’ Experimenten genutzt. Alle Ergebnisse zeigten übereinstimmend einernreversible Bindung ähnlicher Affinität für beide tRNAs und widersprechen somit einer kovalenten Inhibition durch 5FU. Folgerichtig wurde der SDS-stabilernKomplex von TruB mit 5FU-tRNA neu evaluiert, da er bisher als kovalent interpretiert wurde. Es erfolgte eine schnelle Komplexbildung in hoher Ausbeute auchrnfür schlechte Substrate, außerdem ließ sich die Komplexausbeute nicht durch andere Reaktionsbedingungen beeinflussen. Somit kann der SDS stabile Komplexrnnur den ersten, nicht-kovalenten Kontakt von Enzym und 5FU55-tRNA darstellen und repräsentiert kein kovalentes Addukt späterer Katalyse.