Solid-state NMR investigation of phosphonic acid based proton conducting materials

In this work, new promising proton conducting fuel cell membrane materials were characterized in terms of their structure and dynamic properties using solid-state nuclear magnetic resonance (NMR) spectroscopy and X-ray diffraction. Structurally different, phosphonic acid (PA) containing materials were systematically evaluated for possible high-temperature operation (e.g. at T>100°C). Notably, 1H, 2H and 31P magic angle spinning (MAS) NMR provided insight into local connectivities and dynamics of the hydrogen bonded network, while packing arrangements were identified by means of heteronuclear dipolar recoupling techniques.rnThe first part of this work introduced rather crystalline, low molecular weight ionomers for proton conducting membranes, where six different geometries such as line, triangle, screw, tetrahedron, square and hexagon, were investigated. The hexagon was identified as the most promising geometry with high-temperature bulk proton conductivities in the range of 10-3 Scm-1 at a relative humidity of 50%. However, 2H NMR and TGA-MS data suggest that the bulk proton transport is mainly due to the presence of crystal water. Single crystal X-ray data revealed that in the tetrahedron phosphonic acids form tetrameric clusters isolating the mobile protons while the phosphonic acids in the hexagon form zigzag-type pathways through the sample.rnThe second part of this work demonstrates how acid-base pairing and the choice of appropriate spacers may influence proton conduction. Different ratios of statistical copolymers of poly (vinylphosphonic acid) and poly (4-vinylpyridine) were measured to derive information about the local structure and chemical changes. Though anhydrous proton conductivities of all statistical copolymers are rather poor, the conductivity increases to 10-2 S cm-1 when exposing the sample to relative humidity of 80%. In contrast to PVPA, anhydride formation of phosphonic acids in the copolymer is not reversible even when exposing the sample to a relative humidity of 100%.rnIn addition, the influence of both spacers and degree of backbone crystallinity on bulk proton conductivity was investigated. Unlike in systems such as poly benzimidazole (PBI), spacers were inserted between the protogenic groups along the backbone. It was found that dilution of the protogenic groups decreases the conductivity, but compared to PVPA, similar apparent activation energies for local motions were obtained from both variable temperature 1H NMR and impedance spectroscopy data. These observations suggest the formation of phosphonic acid clusters with high degrees of local proton motion, where only a fraction of motions contribute to the observable bulk proton conductivity. Additionally, it was shown that gradual changes of the spacer length lead to different morphologies.rnIn summary, applying advanced solid-state NMR and X-ray analysis, structural and dynamic phenomena in proton conducting materials were identified on a molecular level. The results were discussed with respect to different proton conduction mechanisms and may contribute to a more rational design or improvement of proton conducting membranes.rn

Electrostatic supramolecular assembly of charged dendritic polymers and their biological application

The aim of this study was the development of functional multilayer films through electrostatic layer by layer (LbL) assembly of dendritic macromolecules, the investigation of the fundamental properties of these multilalyered films and the study of their biological applications. rnThe synthesis of the anionic hyperbranched polyglycerols (hbPG) and the preparation of multilayers made of hbPG/phosphorus dendrimer as well as the influences of deposition conditions on multilayers were reported. The thicknesses of multilayer films increase with a decrease of molecular weight of anionic hbPGs. The multilayer films fabricated by low molecular weight hbPGs grow less regularly due to the less charged carboxylic acid groups providing the relative weaker electrostatic forces for the deposition. The thicknesses of multilayer films are reduced with increasing pH values and decreasing the concentration of NaCl. The observed changes of multilayer thickness and surface morphology could be interpreted with the aid of theories regarding the charge density and conformation of the anionic hbPG chains in solution. rnBesides the study of fundamental properties of hbPG/phosphorus multilayer films, antifouling thin films derived from hbPG layers were developed. The antifouling properties of hbPG layers were found to correlate with factors of the molecular weight of anionic hbPG and the film thickness. It was demonstrated that anionic hbPG single layer with highest molecular weight can reduce non specific protein adsorption more efficiently than single layer with lower molecular weight and all the hbPG bilayers possessed excellent property of antifouling. rnPhosphorus dendrimer multilayers were successfully prepared as the platforms to detect DNA immobilization and hybridization. The effect of NaCl concentration on the multilayer film thickness was evaluated to obtain the optimized film thickness. Making use of the multilayer deposited at the optimized condition as a substrate, a high loading of DNA probes was achieved through covalent coupling of probe DNA with the as-formed multilayer films. The hybridization of target DNA with immobilized probe DNA was then carried out and studied by SPFS. The limit of detection upon hybridization was estimated on various dendrimer multilayer platforms. The minimum detection concentration for DNA hybridization is in the same order of magnitude compared with other neutral phosphorus dendrimer systems. Furthermore, the LbL deposition of phosphorus dendrimer multilayers provided a mild and simple way to prepare platforms as DNA microarrays. rnBased on the phosphorus dendrimer multilayer systems, dendritic star polymers were employed which have more reactive groups than that phosphorus dendrimers. The as-assembled dendritic star polymer multilayer films exhibited such distinct morphology characteristics that they underwent extensive structural reorganization upon post-treatment under different pH conditions. Kinetic binding of probe DNA molecules on the outermost negatively charged dendritic surface was studied by SPR as well. The binding capacities of probe DNA on the multilayer surfaces fabricated from the first-generation and the second-generation of dendritic star polymers were compared. The improved binding capacity was achieved from the second-generation of dendritic star polymer multilayer films due to their more reactive groups. DNA hybridization reaction on dendritic multilayer films was investigated by SPFS. The similar hybridization behaviors were found on both multilayer surfaces. Meanwhile, the hybridization kinetic affinities were compared with that of phosphorus dendrimer multilayer surfaces and showed improved detection sensitivity than phosphorus dendrimer multilayer films.rn

Hyperbranched polyether polyols as building blocks for complex macromolecular architectures

The present thesis deals with the development of new branched polymer architectures containing hyperbranched polyglycerol. Materials investigated include hyperbranched oligomers, hyperbranched polyglycerols containing functional initiator-cores at the focal point, well-defined linear-hyperbranched block copolymers and also negatively charged hyperbranched polyelectrolytes.rnHyperbranched oligoglycerols (DPn = 7 and 14) have been synthesized for the first time. The materials show narrow polydispersity (Mw/Mn ca. 1.45) and a very low content in cyclic homopolymers. 13C NMR evidences the dendritic structure of the oligomers and the DB could be calculated (44% and 52%). These new oligoglycerols were compared with the industrial products obtained by polycondensation which exhibit narrow polydispersity (Mw/Mn<1.3) butrnmultimodal distribution in SEC. Detailed 13C NMR and Maldi-ToF studies reveal the presence of branched units and cyclic compounds. In comparison, the hyperbranched oligoglycerols comprise a very low proportion of cyclic homopolymer which render them very interesting materials for biomedical applications for example.rnThe site isolation of the core moiety in dendritic structure offers intriguing potential with respect to peculiar electro-optical properties. Various initiator-cores (n-alkyl amines, UVabsorbing amines and benzophenone) for the ROMBP of glycidol have been tested. The bisglycidolized amine initiator-cores show the best control over the molecular weight and the molecular weight distribution. The photochemical analyses of the naphthalene containingrnhyperbranched polyglycerols show a slight red shift, a pronounced hypochromic effect (decrease of the intensity of the band) compared with the parent model compound and the formation of a relative compact structure. The benzophenone containing polymers adopt an open structure in polar solvents. The fluorescence measurements show a clear “dendritic effect” on the fluorescence intensities and the quantum yield of the encapsulated benzophenone.rnA convenient 3-step strategy has been developed for the preparation of well-defined amphiphilic, linear-hyperbranched block copolymers via hypergrafting. The procedure represents a combination of carbanionic polymerization with the alkoxide-based, controlled ring-opening multibranching polymerization of glycidol. Materials consisting of a polystyrene linear block and a hyperbranched polyglycerol block exhibit narrow polydispersity (1.01-1.02rnfor 5.4% to 27% wt. PG and 1.74 for 52% wt. PG) with a high grafting efficiency. The strategy was also extended to materials with a linear polyisoprene block.rnDetailed investigations of the solution properties of the block copolymers with linear polystyrene blocks show that block copolymer micelles are stabilized by the highly branched block. The morphology of the aggregates is depending on the solvent: in chloroform monodisperse spherical shape aggregates and in toluene ellipsoidal aggregates are formed. On graphite these aggregates show interesting features, giving promising potential applications with respect to the presence of a very dense, functional and stable hyperbranched block.rnThe bulk morphology of the linear-hyperbranched block copolymers has been investigated. The materials with a linear polyisoprene block only behave like complex liquids due to the low Tg and the disordered nature of both components. For the materials with polystyrene, only the sample with 27% wt. hyperbranched polyglycerol forms some domains showing lamellae.rnThe preparation of hyperbranched polyelectrolytes was achieved by post-modification of the hydroxyl groups via Michael addition of acrylonitrile, followed by hydrolysis. In aqueous solution materials form large aggregates with size depending on the pH value. After deposition on mica the structures observed by AFM show the coexistence of aggregates andrnunimers. For the low molecular weight sample (PG 520 g·mol-1) extended and highly ordered terrace structures were observed. Materials were also successfully employed for the fabrication of composite organic-inorganic multilayer thin films, using electrostatic layer-bylayer self-assembly coupled with chemical vapor deposition.

Functionalization of hyperbranched polycarbosilanes - block copolymers and electrochemistry

Polycarbosilanes are a class of polymers at the interface between organic and inorganic chemistry. They are characterized by a high thermal and chemical inertness and high flexibility, especially pronounced for branched structures. Linear polycarbosilanes are well known as precursors for the preparation of SiCx ceramics. Additionally, more sophisticated architectures like dendrimers, hyperbranched polymers or block copolymers have been the subject of research for more than a decade. The scope of this work was to expand the properties and fields of application for polycarbosilane-containing structures. Thus, the work is divided in two major parts. The first part covers the synthesis and characterization of hyperbranched polycarbosilanes containing organometallic moieties. Hyperbranched poly-carbosilanes were synthesized using hydrosilylation of diallylmethylsilane and methyldiundecenylsilane. The degree of branching for polydiallymethylsilane was determined using standard 1H-NMR spectroscopy. The functional building blocks ferrocenyldimethylsilane and diferrocenylmethylsilane were synthesized which contain an isolated ferrocene unit or two ferrocenes bridged by silicon, respectively. Hyperbranched polycarbosilanes functionalized with ferrocenyl moieties were synthesized by modification of preformed polymers or by copolymerization of AB2 carbosilane monomers with AX-type ferrocenylsilanes. Polymers with Mn = 2500-9000g/mol and ferrocene contents of up to 67wt% were obtained. Electrochemical characterization by cyclic voltammetry revealed that polymers functionalized with isolated ferrocene units showed a single reversible oxidation wave, while voltammograms for polymers functionalized with diferrocenyl silane exhibited two well-separated reversible oxidation-reduction waves. This shows that the polymer bound ferrocenes bridged by silicon are electronically communicating and thus oxidation of the first ferrocene shifts the oxidation potential for the adjacent one. The polymers were utilized successfully for the preparation of modified electrodes with persistent and reproducible electrochemical response in organic solvents as well as in aqueous solution. The presented work has proven that ferrocenyl-functionalized hyperbranched polymers exhibit similar electrochemical properties as the analogous dendrimers. In a further approach it was shown that hyperbranched polymers containing organometallic moieties can be synthesized by polymerization of a new ferrocene-containing AB2 monomer - diallylferrocenylsilane. The second part of this work is dedicated to the preparation of core-functional hyperbranched polycarbosilanes. Low molecular weight ambifunctional molecules were synthesized that contain double bonds for the attachment of a polycarbosilane polymer as well as a second functionality available for further reaction and modification. Reactive vinyl groups in the core molecule allow an efficient attachment of hyperbranched polycarbosilane which was proven by MALDI-ToF and GPC. In combination with slow monomer addition techniques molecular weight and polydispersity of the polymers were controlled successfully. Core-functional polymers were characterized by NMR-spectroscopy, MALDI-ToF and GPC. Polymers with polydispersities <2 and molecular weights up to 5300g/mol were obtained. Transformation of the double bonds of the carbosilane was demonstrated with various silanes using hydrosilylation reaction or hydrogenation. Additionally, the core-functionality was varied resulting in polymers with bromo-, phthalimide-, amine- or azide moieties. Thus, a versatile synthetic strategy was developed that allows the synthesis of tailor-made polymers.A promising approach is the application of the polymer building blocks in copolymer synthesis. Bisglycidolization of amine-functional polycarbosilanes produces macro-initiators that are suitable for the multibranching-ring opening polymerization of glycidol. This experiments lead to the first example of hyperbranched-hyperbranched amphiphilic block copolymers, hb-PG-b-hb-PCS. Furthermore, the implementation of copper-catalyzed cycloaddition between azide-functional polycarbosilane and alkyne-functional poly(ethoxyethyl glycidylether) resulted in linear-hyperbranched block copolymers. The facile removal of acetal protecting groups provided convenient access to lin-PG-b-hb-PCS.

Hyperbranched polyglycerols as building blocks for complex amphiphilic structures: synthesis, characterization and applications

Among hyperbranched polymers, polyglycerol is one of the most promising and commonly used macromolecules due to its biocompatibility and versatility. However, the synthesis of high molecular weight polyglycerols still involves many intricacies and has only been understood to a limited extent. Furthermore, only few complex structures like star or block copolymers incorporating polyglycerol have been realized so far. Particularly biocompatible block copolymers are considered promising candidates for biomedical applications.rnThe scope of this thesis was the enhancement of the synthetic process leading to polyglycerol derivatives which implies improved molecular weight control for a broad molecular weight range as well as the assembly of more complex structures like amphiphilic block copolymers. Further insight into the relation between reaction solvent, degree of deprotonation during the ring-opening multibranching polymerization of glycidol and the characteristics of the obtained polymers were achieved within the scope of this work. Based on these results, a novel concept for the preparation of hyperbranched polyglycerols with molecular weights up to 20,000 g/mol was developed, applying a two step synthesis pathway. Starting from a partially deprotonated TMP core, low molecular weight hb-PGs were prepared using the known synthetic protocol that has been established since the late 1990ies. In a subsequent reaction sequence, these well defined polymers were used as hyperbranched macroinitiator cores in order to obtain high molecular weight hb-PGs with remarkably low polydispersity (Mw/Mn < 1.8). Molecular weight control was shown to be excellent and undesired low molecular weight side products were absent. Furthermore, the technique of continuous spin fractionation has been discovered as an efficient method for polyglycerol work-up to remove quantitatively residual monomer- and oligomer traces from hb-PG compositions to result in samples with significantly reduced polydispersities. Based on these results the synthesis of amphiphilic block copolymers containing hydrophilic hyperbranched polyglycerol blocks and linear, apolar poly(propylene oxide) blocks has been significantly improved and augmented to hb-PG-b-l-PPO-b-hb-PG ABA block copolymers. The influence of different polyglycerol-based amphiphiles on the fibril formation was studied by Thioflavin T Fluorescence showing remarkable increasing lag times which is promising in order to enhance the stability of this protein. In addition the first synthesis of poly(glyceryl glycerols) (PGG), introducing a new solketyl glycidyl ether monomer (IGG) was shown. It was furthermore demonstrated that core-functional carbosilane wedges allow application in block copolymer synthesis. Bisglycidolized amine functional polymers were successfully employed as macroinitiators for glycidol polymerization. This resulted in the first example of amphiphilic hyperbranched-hyperbranched polymer structures. Finally, it has been shown that the previously reported synthetic pathway to carboxylated hyperbranched polyglycerol polyelectrolytes can also be applied for the amphiphilic linear-hyperbranched block copolymers. These novel biocompatible and highly amphiphilic polyelectrolytes offer great potential for further investigations. rnrn

Identifizierung chemischer Transportinhibitoren zur Modulation (patho)biologischer Genprodukte

Die intrazelluläre Lokalisation von Proteinen und Makromolekülen unterliegt in Eukaryoten einer strengen Regulation. Insbesondere erlaubt die Kompartimentierung eukaryotischer Zellen in Zellkern und Zytoplasma den simultanen Ablauf räumlich getrennter biochemischer Reaktionen, und damit die unabhängige Regulation zellulärer Programme. Da trotz intensiver Forschungsbemühungen bis dato die molekularen Details sowie die (patho)biologische Bedeutung von Kern-Zytoplasma-Transportprozessen noch immer nicht vollkommen verstanden sind, wurde im Rahmen der vorliegenden Arbeit ein Fokus auf die Identifizierung von chemischen Transportinhibitoren gelegt. Das zu diesem Zweck entwickelte Translokations-Biosensor-System basiert auf der Kombination von autofluoreszierenden Proteinen, sowie spezifisch ausgewählten Kernexport- und Kernimportsignalen. Nach Etablierung geeigneter Zellmodelle, die effizient und stabil die Translokations-Biosensoren exprimieren, wurde die 17 000 Substanzen umfassende Bibliothek der ChemBioNet-Initiative nach Kernexportinhibitoren mittels einer Fluoreszenzmikroskopie-basierten Hochdurchsatzanalyse-Plattform durchmustert. Zunächst wurden Translokations-Algorithmen, welche eine zuverlässige automatisierte Erkennung von Zellkern und Zytoplasma erlauben, optimiert. Im Folgenden konnten acht neue niedermolekulare Kernexport-Inhibitoren identifiziert werden, die sich in der Stärke, der Geschwindigkeit, sowie in der Beständigkeit der vermittelten Inhibition unterscheiden. Die Aktivität der Inhibitoren konnte auf den isolierten nukleären Exportsignalen (NES) von HIV-1 Rev und Survivin als auch auf den entsprechenden Volllängeproteinen mittels Mikroinjektionsexperimenten sowie durch umfassende in vitro und biochemische Methoden bestätigt werden. Zur Untersuchung der funktionellen Einheiten der Inhibitoren wurden homologe Substanzen auf Ihre Aktivität hin getestet. Dabei konnten für die Aktivität wichtige chemische Gruppen definiert werden. Alle Substanzen stellen neue Inhibitoren des Crm1-abhängigen Exports dar und zeigen keine nachweisbare NES-Selektivität. Interessanterweise konnte jedoch eine zytotoxische und Apoptose-induzierende Wirkung auf verschiedene Krebszellarten festgestellt werden. Da diese Wirkung unabhängig vom p53-Status der Tumorzellen ist und die Inhibitoren C3 und C5 die Vitalität nicht-maligner humaner Zellen signifikant weniger beeinträchtigen, wurden diese Substanzen zum internationalen Patent angemeldet. Da der nukleäre Export besonders für Tumorzellen einen wichtigen Überlebenssignalweg darstellt, könnte dessen reversible Hemmung ausgenutzt werden, um besonders in Kombination mit gängigen Krebstherapien eine therapeutisch relevante Tumorinhibition zu erzeugen. Eine weitere Anwendungsmöglichkeit der neuen Exportinhibitoren ist auf dem Gebiet der Infektionskrankheiten zu sehen, da auch die Aktivität des essentiellen HIV-1 Rev-Proteins inhibiert wird. Zusätzlich konnte in der Arbeit gezeigt werden, dass der zelluläre Kofaktor des Crm1-abhängigen Exports des HIV-1 Rev-Proteins, die RNA-Helikase DDX3, ein eigenes NES enthält. Der Nachweis einer direkten Interaktion des HIV-1 Rev- mit dem DDX3-Protein impliziert, dass multiple Angriffstellen für chemische Modulatoren hinsichtlich einer antiviralen Therapie gegeben sind. Da die Vielfalt des chemischen Strukturraums es unmöglich macht diesen experimentell vollständig zu durchmustern, wurden im Rahmen dieser Arbeit auch Naturstoffe als vielversprechende Wirkstoffquelle untersucht. Um zukünftig umfassend bioaktive Substanzen aus diesen hochkomplexen Stoffgemischen experimentell identifizieren zu können, wurde eine Fluoreszenzmikroskopie-basierte Hochdurchsatzanalyse-Plattform am Mainz Screening Center (MSC) etabliert. Damit konnte bereits ein weiterer, bisher unbekannter Exportinhibitor aus Cyphellopsis anomala identifiziert werden. Neben einer Anwendung dieser Substanz als chemisches Werkzeug zur Aufklärung der Regulation von Transportvorgängen, stellt sich auch die evolutionsbiologisch relevante Frage, wie es dem Pilzproduzenten gelingt die Blockierung des eigenen Kernexports zu umgehen. Weiterführende Projekte müssen sich neben der Aufklärung der molekularen Wirkmechanismen der gefundenen Substanzen mit der Identifizierung spezifischer chemischer „Funktionseinheiten“ beschäftigen. Neben einem verbesserten mechanistischen Verständnis von Transportvorgängen stellen die erarbeiteten Transportinhibitoren Vorstufen zur Weiterentwicklung möglicher Wirkstoffe dar. Die im Rahmen dieser Arbeit etablierte Technologie-Plattform und molekularen Werkzeuge stellen darüber hinaus eine wichtige Voraussetzung dar, um eine systematische Suche nach möglichen Wirkstoffen im Forschungsfeld der „Chemischen Biomedizin“ voranzutreiben.

Liquid crystalline cellulose derivatives for mirrorless lasing

In this thesis cholesteric films made of liquid crystalline cellulose derivatives with improved optical properties were prepared. The choice of the solvent, hydrogen bond influencing additives, the synthetic realization of a very high degree of substitution on the cellulosic polymer and the use of mechanical stirring at the upper concentration limit of the liquid crystalline range were the basis for an improved alignment of the applied cellulose tricarbamates. In combination with a tuned substrate treatment and film preparation method, cholesteric films were obtained, with optical properties that were theoretically predicted and only known from low molecular weight liquid crystals so far. Subsequent polymerization allowed a permanent fixing of the alignment and the fabrication of free standing and insensitive films.rnThe incorporation of inorganic nanorods into the cholesteric host material was mediated with tailored block copolymers, available via controlled radical polymerization methods. In addition to the shape match between the rodlike mesogens of the host and the nanorods it was possible to increase the miscibility of both materials. Nevertheless, the size of the nanorods, in comparison to the mesogens, in these densely packed liquid crystalline phases as well as their long equilibration times were the reasons for phase separation. Nanorods are, in principle, valuable substitutes for organics, but their utilization in cellulosic CLC was not to be combined with a high quality alignment of the cholesteric structure.rnA swelling process of polymerized films in a dye solution or dissolving dyes in non-polymerized CLC was used for incorporation of the organic chromophores. With the first method the CLC could be aligned and polymerized without any disturbance due to dye molecules. The optical properties of dye and CLC were matched, with regard to mirrorless lasing devices. The dye was optically excited and laser emission supported by the cholesteric cavity was obtained. The polarization and wavelength of the emitted radiation as well as its bandwidth, the obtained interference pattern and threshold behavior of the emission proofed the feedback mechanism that was not believed to be realizable in liquid crystalline polymers. rnUtilization of a microfluidic co-flow injection device enabled us to transfer the properties of cellulosic CLC from the planar film shape to spherical micrometer sized particles. The pure material yielded particles with distorted mesogen alignment similar to films prepared by capillary flow. Dilution of the CLC with a solvent that migrated into the carrier phase during particle preparation provided the basis for particles with well ordered areas. rnAlthough cellulose derivatives were known for their liquid crystalline behavior for decades and synthesized in mass production, their application as feedback material was affected by bad optical properties. In comparison to low molar mass compounds, the low degree of order in the CLC phase was the cause. With the improved material, defined lasing emission was shown and characterized. Derivatives of cellulose are desirable materials, because, as a renewable resource, they are available in large amounts for a low price and need only simple derivatization reactions. The fabrication of CLC films with tunable lasing emission, for which this thesis can provide a starting point, is in good agreement with today's requirements of modern technology and its miniaturization.rn

Selbstorganisation von Amphiphilen auf Basis von Hexaphenylbenzol und Hexa-peri-hexabenzocoronen

Die Selbstorganisation von amphiphilen Molekülen wird genutzt, um in Lösung, auf der Oberfläche, in der festen Phase und an der Flüssig/Fest-Grenzfläche nanoskopisch strukturierte Materialien zu erhalten. Ziel hierbei ist es, die Dynamik der niedermolekularen Amphiphile mit der Stabilität der hochmolekularen Amphiphile zu vereinigen, um damit die Selbstorganisation der Moleküle zu kontrollieren. Drei Konzepte zur Strukturierung von Kohlenstoff durch Selbstorganisation werden vorgestellt. Im ersten Konzept werden aus Hexaphenylbenzol-Polyethylenglykol- (HPB-PEG) und Hexa-peri-hexabenzocoronen- (HBC-PEG) Derivaten wurmähnliche bzw. faserförmige Strukturen in wässriger Lösung erhalten. Der Wassergehalt in den Hydrogelfasern aus den HPB-PEG-Derivaten kann durch das Substitutionsmuster der Amphiphile und die Länge der PEG-Ketten eingestellt werden. Die Hydrogelfasern ähneln anders als die bisherigen Verfahren, die zur Faserherstellung verwendet werden (Extrudieren, Mikrofluid-Verarbeitung oder Elektrospinning), Systemen in der Natur. Der Beweis für die Bildung von Hydrogelfasern wird mittels spezieller Methoden der polarisierten und depolarisierten dynamischen Lichtstreuung erbracht. Im zweiten Konzept werden durch Elektronenbestrahlung und Pyrolyse von 3',4',5',6'-Tetraphenyl-[1,1':2',1''-terphenyl]-4,4''-dithiol homogene Kohlenstoffmembranen mit Poren erzeugt, die Anwendung in der Filtration finden können und im dritten Konzept wird die Selbstorganisation von einem ortho-verknüpften HPB-Trimer an der Flüssig/Fest-Grenzfläche untersucht. Auf diese Weise werden hochgeordnete lamellare Strukturen erhalten. In allen drei Konzepten sind die Geometrie und die Größe der Moleküle die entscheidenden Parameter zur Erzeugung definierter Strukturen.

Folic acid derivatives for PET imaging and therapy addressing folate receptor positive tumors

Folic acid, also known as vitamin B9, is the oxidized form of 5,6,7,8-tetrahydrofolate, which serves as methyl- or methylene donor (C1-building blocks) during DNA synthesis. Under physiological conditions the required amount of 5,6,7,8-tetrahydrofolate for survival of the cell is accomplished through the reduced folate carrier (RFC). In contrast, the supply of 5,6,7,8-tetrahydrofolate is insufficient under pathophysiological conditions of tumors due to an increased proliferation rate. Consequently, many tumor cells exhibit an (over)expression of the folate receptor. This phenomenon has been applied to diagnostics (PET, SPECT, MR) to image FR-positive tumors and on the other hand to treat malignancies related to a FR (over)expression. Based on this concept, a new 18F-labeled folate for PET imaging has been developed and was evaluated in vivo using tumor-bearing mice. The incorporation of oligoethylene spacers into the molecular structure led to a significant enhancement of the pharmacokinetics in comparison to previously developed 18F-folates. The liver uptake could be reduced by one sixth by remaining a tumor uptake of 3%ID/g leading to better contrast ratios. Encouraged by these results, a clickable 18F-labeled serine-based prosthetic group has been synthesized, again with the idea to improve the metabolic and pharmacokinetic profile of hydrophilic radiotracers. Therefore, an alkyne-carrying azido-functionalized serine derivative for coupling to biomolecules was synthesized and a chlorine leaving group for 18F-labeling, which could be accomplished using a microwave-assisted synthesis, a [K⊂2.2.2]+/carbonate system in DMSO. Radiochemical yields of 77±6% could be achieved.rnThe promising results obtained from the FR-targeting concept in the diagnostic field have been transferred to the boron neutron capture therapy. Therefore, a folate derivative was coupled to different boron clusters and cell uptake studies were conducted. The synthesis of the folate-boron clusters was straightforward. At first, a linker molecule based on maleic acid was synthesized, which was coupled to the boron cluster via Michael Addition of a thiol and alkene and subsequently coupled to the targeting moiety using CuAAC. The new conjugates of folate and boron clusters led to a significant increase of boron concentration in the cell of about 5-times compared to currently used and approved boron pharmaceuticals. rnMoreover, azido-folate derivatives were coupled to macromolecular carrier systems (pHPMA), which showed an enhanced and specific accumulation at target sites (up to 2.5-times) during in vivo experiments. A specific blockade could be observed up to 30% indicating an efficient targeting effect. A new kind of nanoparticles consisting of a PDLLA core and p((HPMA)-b-LMA)) as surfactants were developed and successfully radiolabeled via 18F-click chemistry in good RCYs of 8±3%rnThe nanoparticles were obtained via the miniemulsion technique in combination with solvent evaporation. The 18F-labeled nanoparticles were applied to in vivo testing using a mouse model. PET imaging showed a “mixed” biodistribution of low molecular weight as well as high molecular weight systems, indicating a partial loss of the 18F-labeled surfactant.rnIn conclusion, the presented work successfully utilized the FR-targeting concept in both, the diagnostic field (PET imaging) and for therapeutic approaches (BNCT, drug delivery systems). As a result, the high potential of FR-targeting in oncological applications has been shown and was confirmed by small animal PET imaging.rn

Synthese und Charakterisierung von Polymer-Wirkstoff-Antikörper-Konjugaten zur Anwendung in der Krebsimmuntherapie

Polymere Wirkstoffsysteme gewinnen im Bereich der biomedizinischen Forschung immer größeres Interesse. Vielversprechende Systeme für die Entwicklung von neuartigen Krebs-immun¬therapien stellen insbesondere Polymer-Konjugate dar. Das ideale Polymer-Konjugat besitzt eine Größe zwischen 10 nm und 100 nm, ist nicht zytotoxisch und zeigt keine Aggregation in humanem Blutserum. In der vorliegenden Arbeit wurde die Synthese und Charakterisierung von Polymer-Wirkstoff-Konjugaten zur Anwendung in der Krebsimmuntherapie behandelt. Erstes Ziel der Arbeit war es, geeignete polymere Trägersysteme für die in vivo Anwendung zu finden. Hierzu wurde zunächst die Stabilität verschiedener potentieller polymerer Träger-systeme (Nanohydrogele, Succinyliertes-Poly-L-Lysin (Bürste), ELP-Bürsten und Poly(2-oxazolin)bürsten) in humanem Serum untersucht. Weiterhin wurde die unspezifische Zellaufnahme in murinen dendritischen Zellen (DCs) analysiert. Es konnte gezeigt werden, dass vor allem neutrale bzw. zwitterionische Partikel eine hohe Serumstabilität sowie keine unspezifische Zellaufnahme zeigen. Um eine gezielte Adressierung der DCs des Immunsystems zu erreichen und dadurch eine Immunantwort gegenüber einem bestimmten Krebs Zelltyp zu induzieren, wurden Biokonjugate - auf Basis der Succinylierten-Poly-L-Lysin-(Bürste) sowie der Azid-funktionalisierten Poly(2-oxazolin)bürste (POx) – entwickelt, da diese Polymerbürsten keine bzw. kaum unspezifische Aufnahme in DCs zeigen. Hierbei diente der Antikörper aDEC205 der gezielten Adressierung von CD8+ DCs. Die weiteren bioaktiven Komponenten waren das tumorassoziierte Antigen (TAA) mit der Kernsequenz SIINFEKL zur Induktion einer spezifischen Immunantwort sowie der immunaktivierende TLR9 Ligand, CpG1826. Die Komponenten wurden nacheinander an die Fluoreszenz-markierten Polymere kon¬jugiert. Die Konjugation des Antikörpers erfolgte nach vorangegangener DIBO-Modifizierung über kupferfreie Click-Chemie. Mit einer optimierten Aufarbeitungsmethodik gelang es, aggregat-freie, unimere DIBO-modifizierte aDEC205 Antikörper zu isolieren. Für die succinylierten Poly-L-Lysine konnten keine eindeutigen sowie reproduzierbaren Ergebnisse erhalten werden, sodass sich im weiteren Verlauf der Arbeit auf die POx konzentriert wurde. Die Konjugation von aDEC205 an POx wurde mittels verschiedener physiko-chemischer Methoden (UV-VIS, SDS-PAGE, FCS, GPC, CLSM und FACS) gezeigt. Mit Hilfe von „Specific-Hybridization-Internalisation-Sensor“ Experimenten konnte eine spezifische Aufnahme des Konjugats in CD8+ DCs nachgewiesen werden. rnDie Konjugation von Antigen und CpG erfolgte ebenso nach entsprechender Modifizierung über kupferfreie Click-Chemie. SDS-PAGE, UV-VIS und FCS bestätigten eine erfolgreiche Kopplung. T-Zell-Proliferationsversuche ergaben für Antigen enthaltende Polymer-Konjugate eine CD8+ T-Zell-Aktivierung. Des Weiteren zeigten die POx keine bemerkenswerte Toxizität und deren Konjugate keine Aggregation in humanem Serum. rnrnDarüber hinaus wurde der Einfluss verschiedener Polymertopologien auf ihre Biodistribution sowie Blutzirkulation untersucht. Für die nach GPC-Fraktionierung erhaltenen verschiedenen Polymerfraktionen - hochmolekulare wurmartige Polymerbürsten, ellipsoidartige Polymer-bürsten und niedermolekulare kugelförmige Moleküle - konnten vielversprechende Ergebnisse erhalten werden.

Synthese und Charakterisierung von Poly(tert-butylacrylat)- und Polyacrylsäure-Sternpolymeren

Sternpolymere aus Poly(tert.-butylacrylat)-Armen und einem Mikrogel-Core aus Ethylenglykoldimethacrylat wurden nach der arm-first Strategie hergestellt. Diese weisen eine enge Armzahlverteilung auf. Mit sinkender Precursorlänge, mit steigendem Verhältnis [bifunktionelles Monomer]/[Initiator], sowie mit zunehmender Reaktionszeit und Gesamtkonzentration nimmt die mittlere Armzahl fn zu. Die Sternbildung verläuft ähnlich einer Polykondensation. Die Molekulargewichte wurden mittels GPC gekoppelt mit einem online-Viskosimeter und einem online-Vielwinkellichtstreudetektor (MALLS) bestimmt.Die intrinsischen Viskositäten der Sternpolymere sind sehr niedrig. Für Armzahlen f ca. 8 erhält man ein Maximum in der doppellogarithmischen Auftragung der intrinsischen Viskosität und des Molekulargewichts. Die Trägheitsradien nehmen nur wenig mit dem Molekulargewicht zu. Die erhaltenen Koeffizienten liegen im von Daoud und Cotton vorhergesagten Bereich. Die Schrumpfungsfaktoren sinken auf g ca. 0,2 bzw. g' ca. 0,25. Aus den Poly(tert.-butylacrylat)-Sternpolymeren wurden durch Verseifung mit HBr in Methanol Polyacrylsäure-Sternpolymere hergestellt, welche ebenfalls mittels GPC-Viskosimetrie und GPC-MALLS charakterisiert wurden. Für die ionischen Sternpolymere findet man deutlich höhere Schrumpfungsfaktoren, kein Maximum in der intrinsischen Viskosität und höhere Exponenten als von Daoud und Cotton vorhergesagt. Erklärt wurde dies mit der hohen Segmentdichte in Sternpolymeren, die bei den ionischen Sternpolymeren zu einer hohen Ladungsdichte führt. Dadurch müssen sich die Arme stärker strecken als bei nicht-ionischen Sternen und es resultieren größere Moleküldimensionen.

Kinetische Untersuchungen zur Synthese von Blockcopolymeren mit Methacrylatsegmenten durch neue anionische Polymerisationssysteme

Ein metallfreies Reaktionssystem mit Bis(triphenylphosphoranyliden)ammonium-Kationen als Gegenionen sowie das Additiv Lithium-2-methoxyethoxid wurden auf ihre Eignung zur anionischen Synthese von Blockcopolymeren mit (Meth)acrylatsegmenten bei moderaten Temperaturen im Strömungsrohr-Reaktor untersucht. Das metallfreie System ist zur lebenden Polymerisation von Methacrylaten in THF mit engen Molekulargewichtsverteilungen bei Reaktionszeiten < 1 s bis zu Temperaturen von 0 °C geeignet. In Gegenwart von Metallionen (Li+) findet eine Verlangsamung der Polymerisation unter Verlust der Reaktionskontrolle statt, Lithiumenolate verursachen nun breite, multimodale Molekulargewichtsverteilungen. Eine lebende Polymerisation von Acrylaten ist nicht möglich, massenspektroskopische Untersuchungen der Produkte weisen auf einen komplexen Reaktionsmechanismus mit Abbruch- und Übertragungsreaktionen hin. Die Synthese von Poly(styrol)-block-Poly(1,4-butadien)-block-Poly(methylmethacrylat)-Copolymeren in Toluol ist mit Lithium-2-methoxyethoxid als Additiv für die MMA-Polymerisation bei moderaten Mischtemperaturen (T < 0 °C) im Strömungsrohr-Reaktor möglich, die Effektivität des Wechselschritts von Polybutadien zu PMMA beträgt im Durchschnitt ca. 50 %. Untersuchungen verschiedener Reaktionsparameter, wie z.B. der Endfunktionalisierung des Polybutadiens mit 1,1-Diphenylethylen und der Temperatur während der Verkappung und der MMA-Polymerisation, geben keine eindeutigen Hinweise auf die Ursache dieses Phänomens. MALDI-TOF-Massenspektren des unreagierten Polybutadien Precursors zeigen die Anlagerung von 1-3 Molekülen Methylmethacrylat und keinen Abbruch durch Backbiting, was auf die Ausbildung stabiler Aggregate hindeutet.

Cellulose based Lithium ion polymer electrolytes for Lithium batteries

The separator membrane in batteries and fuel cells is of crucial importance for the function of these devices. In lithium ion batteries the separator membrane as well as the polymer matrix of the electrodes consists of polymer electrolytes which are lithium ion conductors. To overcome the disadvantage of currently used polymer electrolytes which are highly swollen with liquids and thus mechanically and electrochemically unstable, the goal of this work is a new generation of solid polymer electrolytes with a rigid backbone and a soft side chain structure. Moreover the novel material should be based on cheap substrates and its synthesis should not be complicated aiming at low overall costs. The new materials are based on hydroxypropylcellulose and oligoethyleneoxide derivatives as starting materials. The grafting of the oligoethyleneoxide side chains onto the cellulose was carried out following two synthetic methods. One is based on a bromide derivative and another based on p-toluolsulfonyl as a leaving group. The side chain reagents were prepared form tri(ethylene glycol) monoethyl ether. In order to improve the mechanical properties the materials were crosslinked. Two different conceptions have been engaged based on either urethane chemistry or photosensitive dimethyl-maleinimide derivatives. PEO - graft - cellulose derivatives with a high degree of substitution between 2,9 and 3,0 were blended with lithium trifluoromethane-sulfonate, lithium bis(trifluorosulfone)imide and lithium tetrafluoroborate. The molar ratios were in the range from 0,02 to 0,2 [Li]/[O]. The products have been characterized with nuclear magnetic resonance (NMR), gel permeation chromatography (GPC) and laserlight scattering (LS) with respect to their degree of substitution and molecular weight. The effect of salt concentration on ionic conductivity, thermal behaviour and morphology has been investiga-ted with impedance spectroscopy, differential scanning calorimetry (DSC) and thermal gravimetric analysis (TGA). The crosslinking reactions were controlled with dynamic mechanical analysis (DMS). The degree of substitution of our products is varying between 2,8 and 3,0 as determined by NMR. PEO - graft - cellulose derivatives are highly viscous liquids at room temperature with glass transition temperatures around 215 K. The glass transition temperature for the Lithium salt complexes of PEO - graft - cellulose deri-vatives increase with increasing salt content. The maximum conductivity at room temperature is about 10-4 and at 100°C around 10-3 Scm-1. The presence of lithium salt decreases the thermal stability of the complexes in comparison to pure PEO - graft - cellulose derivatives. Complexes heated over 140 – 150°C completely lose their ionic conductivity. The temperature dependence of the conductivity presented as Arrhenius-type plots for all samples is similar in shape and follows a VTF behaviour. This proofs that the ionic transport is closely related to the segmental motions of the polymer chains. Novel cellulose derivatives with grafted oligoethylen-oxide side chains with well-defined chemical structure and high side chain grafting density have been synthesized. Cellulose was chosen as stiff, rod like macromolecule for the backbone while oligoethylen-oxides are chosen as flexible side chains. A maximum grafting density of 3.0 have been obtained. The best conductivity reaches 10-3 Scm-1 at 100°C for a Li-triflate salt complex with a [Li]/[O] ratio of 0.8. The cross-linked complexes containing the lithium salts form elastomeric films with convenient mechanical stability. Our method of cellulose modification is based on relatively cheap and commercially available substrates and as such appears to be a promising alternative for industrial applications.

Synthesis and characterization of novel poly(imino ketone)s via palladium-catalyzed aryl amination

The challenge of the present work was to synthesize and to characterize new classes of N-containing polymers via palladium-catalyzed aryl amination. This work was inspired by a desire to combine the properties of high-performance polymers such as PEKs with those of N-containing conductive polymers such as polyaniline (PANI), poly(aromatic amides) (PAAs), and the ready synthesis of N-containing simple aromatic compound by the Buchwald-Hartwig reaction. Careful investigation of a model reaction was carried out to provide insights into the formation of side products which will have a negative effect upon the molecular weight or upon the materials properties of the desired polymers in the polycondensation reaction. In this thesis, five new different polymer classes namely, poly(imino ketone)s (PIKs), poly(imino acridine)s (PIAcs), poly(imino azobenzene)s (PIAzos), poly(imino fluorenone)s (PIFOs), and poly(imino carbazole)s (PICs) were synthesized and fully characterized by means of 1H-NMR, elemental analysis, UV, FT-IR, X-ray, GPC, TGA, DSC, DMA, and dielectric spectroscopy. To optimize the polycondensation process, the influence of the concentration, temperature, ligands and the reactivity of the halogen containing monomers were investigated. A temperature of 100-165 °C and a concentration of 30-36 % were found to be optimal for the palladium-catalyzed polycondensation to produce polymer with high molecular weight (Mn = 85 900, Mw = 474 500, DP = 126). Four different ligands were used successfully in the Pd-catalyzed process, of which the Pd/BINAP system was found to be the most effective catalyst, producing the highest yield and highest molecular weight polymers. It was found that the reactivity decreases strongly with increasing electronegativity of the halogen atoms, for example better yields, and higher molecular weights were obtained by using dibromo compounds than dichloro compounds while difluoro compounds were totally unreactive. Polymer analogous transformations, such as the protonation reaction of the ring nitrogens in PIAcs, or of the azobenzene groups of PIAzos, the photo and thermal cis-trans-isomerization of PIAzos, and of poly(imino alcohol)s were also studied. The values of the dielectric constants of PIKs at 1 MHz were in the range 2.71-3.08. These low values of the dielectric constant are lower than that of "H Film", a polyimide Kapton film which is one of the most preferred high-performance dielectrics in microelectronic applications having a dielectric constant of 3.5. In addition to the low values of the dielectric constants, PIKs have lower and glass transition temperatures (Tgs) than arimides such as Kapton which may make them more easily processable. Cyclic voltammetry showed that PICs exhibited low oxidation and reduction potentials and their values were shifted to low values with increasing degree of polymerization i.e. with increasing of the carbazole content in backbone of PICs (PIC-7, 0.44, 0.33 V, DP= 37, PIC-5, 0.63, 0.46, DP= 16, respectively).

New synthetic strategies to tethered bilayer lipid membranes

Tethered bilayer lipid membranes provide an efficient, stable and versatile platform for the investigation of integrated membrane proteins. However, the incorporation of large proteins, as well as of proteins with a large submembrane part is still a very critical issue and therefore, further optimisation of the system is necessary. The central element of a tBLM is a lipid bilayer. Its proximal leaflet is, at least to some extend, covalently attached to a solid support via a spacer group. The anchor lipid consists of three distinct parts, a lipid headgroup, a spacer group and an anchor. All parts together influence the final bilayer properties. In the frame of this work, the synthesis of new thiolipids for tBLMs on gold has been investigated. The aim was to obtain molecules with longer spacers in order to increase the submembrane space. The systems obtained have been characterized using SPR and EIS. The results obtained during this study are multiple. First, the synthesis of a previously synthesized architecture was successfully scaled up in an industrial lab using a new synthetic approach. The synthesis of large amounts is now feasible. Then, the synthesis of the new thiolipids was carried out taking into account the following requirements: the increase of the submembrane space by having longer ethyleneglycol spacers, the attachment of the molecules to a gold substrate via a thiol bond, and the tunability of the lateral mobility by changing the lipid headgroup. Three different synthetic strategies have been investigated. The polymeric approach did not prove to be successful, merely because of the broad molecular weight distribution. The synthesis of heterofunctionally protected oligoethyleneglycols allowed to obtain ethyleneglycol moieties with 6 and 8 units, but the tedious purification steps gave very low yields. Finally, the block by block synthesis using ethyleneglycol precursors proved to be an efficient and fast method to synthesize the target molecules. Indeed, these were obtained with very high yields, and the separation was very efficient. A whole family of new compounds was obtained, having 6, 8 and 14 ethyleneglycol units and with mono- or diphytanyl lipid headgroups. This new pathway is a very promising synthetic strategy that can be used further in the development of new compounds of the tether system. The formation of bilayers was investigated for the different thiolipids mainly by using EIS. The electrical properties of a bilayer define the quality of the membrane and allow the study of the functionality of proteins embedded in such a system. Despite multiple trials to improve the system using self assembly, Langmuir Blodgett transfer, and detergent mixed vesicles, the new polymer thiolipids did not show as high electrical properties as tBLMs reported in the literature. Nevertheless, it was possible to show that a bilayer could be obtained for the different spacer lengths. These bilayers could be formed using self assembly for the first monolayer, and two different methods for bilayer formation, namely vesicle fusion and solvent exchange. We could furthermore show functional incorporation of the ion carrier valinomycin: the selective transport of K+ ions could be demonstrated. For DPHL, it was even possible to show the functional incorporation of the ion channel gramicidin. The influence of the spacer length is translated into an increase of the spacer capacitance, which could correspond to an increase in the capacity of charge accumulation in the submembrane space. The different systems need to be further optimised to improve the electrical properties of the bilayer. Moreover, the incorporation of larger proteins, and proteins bearing submembrane parts needs to be investigated.