Passive based control on a kuka arm

L'interazione in maniera sicura e compliante è una caratteristica sempre più richiesta per i sistemi robotici. La modellazione di sistemi eseguita tramite l'uso di sistemi port-Hamiltoninani permette di comprendere cosa avviene a livello energetico durante l'interazione e aiuta nella progettazinoe di un controllore tale che il comportamento del sistema controllato sia passivo e sicuro durante essa. Ciò sfocia nel cosiddetto Controllore Intrinsicamente Passivo (IPC). Dal momento che questo un controllo impone la rigidezza desiderata al sistema controllato, è possibile, tra le altre cose, replicare il comportamento del dispositivo RCC (Centro Remoto di Complianza) e di migliorarlo in modo tale che durante l'azione di peg-in-hole il buco sia meno sollecitato dal robot.

Characterization of X-ray detectors based on organic semiconducting single crystals

Negli anni recenti, lo sviluppo dell’elettronica organica ha condotto all’impiego di materiali organici alla base di numerosi dispositivi elettronici, quali i diodi ad emissione di luce, i transistor ad effetto di campo, le celle solari e i rivelatori di radiazione. Riguardo quest’ultimi, gli studi riportati in letteratura si riferiscono per la maggiore a dispositivi basati su materiali organici a film sottile, che tuttavia presentano problemi relativi ad instabilità e degradazione. Come verrà illustrato, l’impiego di singoli cristalli organici come materiali alla base di questi dispositivi permette il superamento delle principali limitazioni che caratterizzano i rivelatori basati su film sottili. In questa attività sperimentale, dispositivi basati su cristalli organici semiconduttori verranno caratterizzati in base alle principali figure di merito dei rivelatori. Tra i campioni testati, alcuni dispositivi basati su singoli cristalli di 6,13-bis (triisopropylsilylethynyl)-pentacene (TIPS-Pentacene) e 5,6,11,12-tetraphenyltetracene (Rubrene) hanno mostrato interessanti proprietà e sono stati quindi maggiormente studiati.

Novel materials for direct X-ray detectors based on semiconducting organic polymers

Conventional inorganic materials for x-ray radiation sensors suffer from several drawbacks, including their inability to cover large curved areas, me- chanical sti ffness, lack of tissue-equivalence and toxicity. Semiconducting organic polymers represent an alternative and have been employed as di- rect photoconversion material in organic diodes. In contrast to inorganic detector materials, polymers allow low-cost and large area fabrication by sol- vent based methods. In addition their processing is compliant with fexible low-temperature substrates. Flexible and large-area detectors are needed for dosimetry in medical radiotherapy and security applications. The objective of my thesis is to achieve optimized organic polymer diodes for fexible, di- rect x-ray detectors. To this end polymer diodes based on two different semi- conducting polymers, polyvinylcarbazole (PVK) and poly(9,9-dioctyluorene) (PFO) have been fabricated. The diodes show state-of-the-art rectifying be- haviour and hole transport mobilities comparable to reference materials. In order to improve the X-ray stopping power, high-Z nanoparticle Bi2O3 or WO3 where added to realize a polymer-nanoparticle composite with opti- mized properities. X-ray detector characterization resulted in sensitivties of up to 14 uC/Gy/cm2 for PVK when diodes were operated in reverse. Addition of nanoparticles could further improve the performance and a maximum sensitivy of 19 uC/Gy/cm2 was obtained for the PFO diodes. Compared to the pure PFO diode this corresponds to a five-fold increase and thus highlights the potentiality of nanoparticles for polymer detector design. In- terestingly the pure polymer diodes showed an order of magnitude increase in sensitivity when operated in forward regime. The increase was attributed to a different detection mechanism based on the modulation of the diodes conductivity.

An inter-comparison between a VIS/IR and a MW satellite-based methods for cloud detection and classification

This thesis is aimed to assess similarities and mismatches between the outputs from two independent methods for the cloud cover quantification and classification based on quite different physical basis. One of them is the SAFNWC software package designed to process radiance data acquired by the SEVIRI sensor in the VIS/IR. The other is the MWCC algorithm, which uses the brightness temperatures acquired by the AMSU-B and MHS sensors in their channels centered in the MW water vapour absorption band. At a first stage their cloud detection capability has been tested, by comparing the Cloud Masks they produced. These showed a good agreement between two methods, although some critical situations stand out. The MWCC, in effect, fails to reveal clouds which according to SAFNWC are fractional, cirrus, very low and high opaque clouds. In the second stage of the inter-comparison the pixels classified as cloudy according to both softwares have been. The overall observed tendency of the MWCC method, is an overestimation of the lower cloud classes. Viceversa, the more the cloud top height grows up, the more the MWCC not reveal a certain cloud portion, rather detected by means of the SAFNWC tool. This is what also emerges from a series of tests carried out by using the cloud top height information in order to evaluate the height ranges in which each MWCC category is defined. Therefore, although the involved methods intend to provide the same kind of information, in reality they return quite different details on the same atmospheric column. The SAFNWC retrieval being very sensitive to the top temperature of a cloud, brings the actual level reached by this. The MWCC, by exploiting the capability of the microwaves, is able to give an information about the levels that are located more deeply within the atmospheric column.

The contribution of the Finite Volume Point Dilution Method to the determination of solute mass flux in an alluvial aquifer.

Groundwater represents one of the most important resources of the world and it is essential to prevent its pollution and to consider remediation intervention in case of contamination. According to the scientific community the characterization and the management of the contaminated sites have to be performed in terms of contaminant fluxes and considering their spatial and temporal evolution. One of the most suitable approach to determine the spatial distribution of pollutant and to quantify contaminant fluxes in groundwater is using control panels. The determination of contaminant mass flux, requires measurement of contaminant concentration in the moving phase (water) and velocity/flux of the groundwater. In this Master Thesis a new solute flux mass measurement approach, based on an integrated control panel type methodology combined with the Finite Volume Point Dilution Method (FVPDM), for the monitoring of transient groundwater fluxes, is proposed. Moreover a new adsorption passive sampler, which allow to capture the variation of solute concentration with time, is designed. The present work contributes to the development of this approach on three key points. First, the ability of the FVPDM to monitor transient groundwater fluxes was verified during a step drawdown test at the experimental site of Hermalle Sous Argentau (Belgium). The results showed that this method can be used, with optimal results, to follow transient groundwater fluxes. Moreover, it resulted that performing FVPDM, in several piezometers, during a pumping test allows to determine the different flow rates and flow regimes that can occurs in the various parts of an aquifer. The second field test aiming to determine the representativity of a control panel for measuring mass flus in groundwater underlined that wrong evaluations of Darcy fluxes and discharge surfaces can determine an incorrect estimation of mass fluxes and that this technique has to be used with precaution. Thus, a detailed geological and hydrogeological characterization must be conducted, before applying this technique. Finally, the third outcome of this work concerned laboratory experiments. The test conducted on several type of adsorption material (Oasis HLB cartridge, TDS-ORGANOSORB 10 and TDS-ORGANOSORB 10-AA), in order to determine the optimum medium to dimension the passive sampler, highlighted the necessity to find a material with a reversible adsorption tendency to completely satisfy the request of the new passive sampling technique.

Sistema Bluetooth-based di remarketing pervasivo

Il progetto si propone di dotare la realta fisica di un estensione digitale. Sensori, attuatori e tecnologie embedded hanno cambiato il nostro modo di lavorare, allenarci e seguire i nostri interessi. Il mondo del commercio non e rimasto a guardare ed ha dovuto adattarsi alla metamorfosi high-tech del settore dei servizi. Il sistema proposto costituisce un promotore per acquisti ed un raccoglitore intelligente di abitudini sullo shopping e si compone di applicazione mobile, microcontroller e web server. Caratteristica prima e principale del progetto e sicuramente la pervasivita. All'utente ed utilizzatore dell'app dello shopping center deve essere certamente resa nota la collaborazione al fine di raccogliere dati statistici sulle sue abitudini, tuttavia sono le modalita di tale operazione a dover rimanere velate, in modo da non appesantire il cliente con tediose operazioni di invio di feedback e valutazioni ed allo stesso tempo permettere una raccolta capillare delle informazioni. Parallelamente alla raccolta di dati funzionali al producer, sono state implementate features per il consumatore, come notifiche promozionali place-triggered e pubblicita mirata. Tra tutte le tecnologie adibite allo scambio di informazioni, si e scelto l'utilizzo del Bluetooth e del piu recente Bluetooth Low Energy (BLE) per permettere ai dispositivi di comunicare tra loro.

Development of a fluorescent-based single liposome assay for studying calcium transporter LMCA1

The morphological and functional unit of all the living organisms is the cell. The transmembrane proteins, localized in the plasma membrane of cells, play a key role in the survival of the cells themselves. These proteins perform a variety of different tasks, for example the control of the homeostasis. In order to control the homeostasis, these proteins have to regulate the concentration of chemical elements, like ions, inside and outside the cell. These regulations are fundamental for the survival of the cell and to understand them we need to understand how transmembrane proteins work. Two of the most important categories of transmembrane proteins are ion channels and transporter proteins. The ion channels have been depth studied at the single molecule level since late 1970s with the development of patch-clamp technique. It is not possible to apply this technique to study the transporter proteins so a new technique is under development in order to investigate the behavior of transporter proteins at the single molecule level. This thesis describes the development of a nanoscale single liposome assay for functional studies of transporter proteins based on quantitative fluorescence microscopy in a highly-parallel manner and in real time. The transporter of interest is the prokaryotic transporter Listeria Monocytogenes Ca2+-ATPase1 (LMCA1), a structural analogue of the eukaryotic calcium pumps SERCA and PMCA. This technique will allow the characterization of LMCA1 functionality at the single molecule level. Three systematically characterized fluorescent sensors were tested at the single liposome scale in order to investigate if their properties are suitable to study the function of the transporter of interest. Further studies will be needed in order to characterize the selected calcium sensor and pH sensor both implemented together in single liposomes and in presence of the reconstituted protein LMCA1.

Measurement of tt ̄production cross section at 13 TeV in the fully-hadronic channel with CMS

Lo scopo di questa tesi è la misura di sezione d’urto di produzione di coppie top-antitop nel canale adronico. Per la misura sono stati utilizzati i dati raccolti dall’esperimento CMS in collisioni protone-protone ad LHC, con un’energia nel centro di massa pari a 13 TeV. Il campione di dati utilizzato corrisponde ad una luminosità integrata di 2.474 f b^ −1 . L’analisi dati inizia selezionando gli eventi che soddisfano determinate condizioni (e.g. trigger, tagli cinematici, sei o più jet, almeno 2 jet provenienti dall’adronizzazione di due quark bottom) con lo scopo di incrementare la purezza del segnale scartando il più possibile gli eventi di fondo. A seguire, viene ricostruita la massa del quark top usando un fit cinematico. Sulle distribuzioni di tale massa si basa la stima degli eventi di fondo e di segnale. Infine, attraverso un fit di verosimiglianza, si ottiene il valore della sezione d’urto: σ t t ̄ = 893 ± 57 (stat) ± 104 (syst) pb. Questo risultato è in buon accordo con il valore teorico di 832 pb e con altre misure di CMS effettuate in canali differenti.