Development and performance assessment of a Plasma Focus electron beam generator for Intra-Operative Radiation Therapy

The Plasma Focus is a device designed to generate a plasma sheet between two coaxial electrodes by means of a high voltage difference. The plasma is then driven to collapse into a “pinch”, where thermonuclear conditions prevail. During the “pinch phase” charged particles are emitted, with two main components: an ion beam peaked forward and an electron beam directed backward. The electron beam emitted backward by Plasma Focus devices is being investigated as a radiation source for medical applications, using it to produce x-rays by interaction with appropriate targets (through bremsstrahlung and characteristic emission). A dedicated Plasma Focus device, named PFMA-3 (Plasma Focus for Medical Applications number 3), has been designed, put in operation and tested by the research groups of the Universities of Bologna and Ferrara. The very high dose rate (several gray per discharge, in less than 1 µs) is a peculiarity of this device that has to be investigated, as it might modify the relative biological effectiveness (RBE). Aim of this Ph.D. project was to investigate the main physical properties of the low-energy x-ray beams produced by a Plasma Focus device and their potential medical applications to IORT treatments. It was necessary to develop the optimal geometrical configuration; to evaluate the x-rays produced and their dose deposited; to estimate the energy electron spectrum produced in the “pinch phase”; to study an optimal target for the conversion of the x-rays; to conduct simulations to study the physics involved; and in order to evaluate the radio-biological features of the beam, cell holders had to be developed for both irradiations and cell growth conditions.

Modelling and Design of Advanced Reliable Circuits and Devices for Energy Efficiency

Reliable electronic systems, namely a set of reliable electronic devices connected to each other and working correctly together for the same functionality, represent an essential ingredient for the large-scale commercial implementation of any technological advancement. Microelectronics technologies and new powerful integrated circuits provide noticeable improvements in performance and cost-effectiveness, and allow introducing electronic systems in increasingly diversified contexts. On the other hand, opening of new fields of application leads to new, unexplored reliability issues. The development of semiconductor device and electrical models (such as the well known SPICE models) able to describe the electrical behavior of devices and circuits, is a useful means to simulate and analyze the functionality of new electronic architectures and new technologies. Moreover, it represents an effective way to point out the reliability issues due to the employment of advanced electronic systems in new application contexts. In this thesis modeling and design of both advanced reliable circuits for general-purpose applications and devices for energy efficiency are considered. More in details, the following activities have been carried out: first, reliability issues in terms of security of standard communication protocols in wireless sensor networks are discussed. A new communication protocol is introduced, allows increasing the network security. Second, a novel scheme for the on-die measurement of either clock jitter or process parameter variations is proposed. The developed scheme can be used for an evaluation of both jitter and process parameter variations at low costs. Then, reliability issues in the field of “energy scavenging systems” have been analyzed. An accurate analysis and modeling of the effects of faults affecting circuit for energy harvesting from mechanical vibrations is performed. Finally, the problem of modeling the electrical and thermal behavior of photovoltaic (PV) cells under hot-spot condition is addressed with the development of an electrical and thermal model.

Interference Management and Energy Efficiency in Satellite Communications

The main areas of research of this thesis are Interference Management and Link-Level Power Efficiency for Satellite Communications. The thesis is divided in two parts. Part I tackles the problem of interference environments in satellite communications, and interference mitigation strategies, not just in terms of avoidance of the interferers, but also in terms of actually exploiting the interference present in the system as a useful signal. The analysis follows a top-down approach across different levels of investigation, starting from system level consideration on interference management, down to link-level aspects and to intra-receiver design. Interference Management techniques are proposed at all the levels of investigation, with interesting results. Part II is related to efficiency in the power domain, for instance in terms of required Input Back-off at the power amplifiers, which can be an issue for waveform based on linear modulations, due to their varying envelope. To cope with such aspects, an analysis is carried out to compare linear modulation with waveforms based on constant envelope modulations. It is shown that in some scenarios, constant envelope waveforms, even if at lower spectral efficiency, outperform linear modulation waveform in terms of energy efficiency.

Miglioramento delle performance termiche e energetiche degli edifici rurali: valutazione del retrofit di locali per la conservazione del vino su casi studio

Il presente studio si colloca all’interno di una ricerca più ampia volta alla definizione di criteri progettuali finalizzati all’ottimizzazione delle prestazioni energetiche delle cantine di aziende vitivinicole, di dimensioni produttive medio - piccole. Nello specifico la ricerca riguarda la riqualificazione di fabbricati rurali esistenti di modeste dimensioni, da convertire a magazzini per la conservazione del vino in bottiglia. Lo studio si pone come obiettivo la definizione di criteri di analisi per la valutazione di interventi di retrofit di tali fabbricati, volto sia al miglioramento delle prestazioni energetiche dell’involucro edilizio, sia alla riduzione del fabbisogno energetico legato al funzionamento di eventuali impianti di controllo termico. La ricerca è stata condotta mediante l’utilizzo del software di simulazione termica Energy Plus, per ottenere i valori simulati di temperatura interna relativi ai diversi scenari migliorativi ipotizzati, e mediante la successiva definizione di indicatori che esplicitino l’influenza delle principali variabili progettuali sull’andamento delle temperature interne dei locali di conservazione e sul fabbisogno energetico del fabbricato necessario a garantire l’intervallo di temperatura di comfort del vino. Tra tutti gli interventi possibili per il miglioramento della prestazione energetica degli edifici, quelli analizzati in questo studio prevedono l’aggiunta di un isolamento a cappotto delle pareti esterne, l’isolamento della copertura e l’aggiunta di una struttura ombreggiante vegetale esterna. I risultati ottenuti danno una prima indicazione sugli interventi più efficaci in termini di miglioramento energetico e mettono in luce l’utilità del criterio proposto nell’evidenziare le criticità degli interventi migliorativi ipotizzati. Il metodo definito nella presente ricerca risulta quindi un valido strumento di valutazione a supporto della progettazione degli interventi di retrofit dei fabbricati rurali da convertire a magazzini per la conservazione del vino.

Development of An Energy Modeling Approach to Analyse Historical Building Performance

In the last years the attentions on the energy efficiency on historical buildings grows, as different research project took place across Europe. The attention on combining, the need of the preservation of the buildings, their value and their characteristic, with the need of the reduction of energy consumption and the improvements of indoor comfort condition, stimulate the discussion of two points of view that are usually in contradiction, buildings engineer and Conservation Institution. The results are surprising because a common field is growing while remains the need of balancing the respective exigencies. From these experience results clear that many questions should be answered also from the building physicist regarding the correct assessment: on the energy consumption of this class of buildings, on the effectiveness of the measures that could be adopted, and much more. This thesis gives a contribution to answer to these questions developing a procedure to analyse the historic building. The procedure gives a guideline of the energy audit for the historical building considering the experimental activities to dial with the uncertainty of the estimation of the energy balance. It offers a procedure to simulate the energy balance of building with a validated dynamic model considering also a calibration procedure to increase the accuracy of the model. An approach of design of energy efficiency measures through an optimization that consider different aspect is also presented. All the process is applied to a real case study to give to the reader a practical understanding.

Body ares networks for human motor assessment

Healthcare, Human Computer Interfaces (HCI), Security and Biometry are the most promising application scenario directly involved in the Body Area Networks (BANs) evolution. Both wearable devices and sensors directly integrated in garments envision a word in which each of us is supervised by an invisible assistant monitoring our health and daily-life activities. New opportunities are enabled because improvements in sensors miniaturization and transmission efficiency of the wireless protocols, that achieved the integration of high computational power aboard independent, energy-autonomous, small form factor devices. Application’s purposes are various: (I) data collection to achieve off-line knowledge discovery; (II) user notification of his/her activities or in case a danger occurs; (III) biofeedback rehabilitation; (IV) remote alarm activation in case the subject need assistance; (V) introduction of a more natural interaction with the surrounding computerized environment; (VI) users identification by physiological or behavioral characteristics. Telemedicine and mHealth [1] are two of the leading concepts directly related to healthcare. The capability to borne unobtrusiveness objects supports users’ autonomy. A new sense of freedom is shown to the user, not only supported by a psychological help but a real safety improvement. Furthermore, medical community aims the introduction of new devices to innovate patient treatments. In particular, the extension of the ambulatory analysis in the real life scenario by proving continuous acquisition. The wide diffusion of emerging wellness portable equipment extended the usability of wearable devices also for fitness and training by monitoring user performance on the working task. The learning of the right execution techniques related to work, sport, music can be supported by an electronic trainer furnishing the adequate aid. HCIs made real the concept of Ubiquitous, Pervasive Computing and Calm Technology introduced in the 1988 by Marc Weiser and John Seeley Brown. They promotes the creation of pervasive environments, enhancing the human experience. Context aware, adaptive and proactive environments serve and help people by becoming sensitive and reactive to their presence, since electronics is ubiquitous and deployed everywhere. In this thesis we pay attention to the integration of all the aspects involved in a BAN development. Starting from the choice of sensors we design the node, configure the radio network, implement real-time data analysis and provide a feedback to the user. We present algorithms to be implemented in wearable assistant for posture and gait analysis and to provide assistance on different walking conditions, preventing falls. Our aim, expressed by the idea to contribute at the development of a non proprietary solutions, driven us to integrate commercial and standard solutions in our devices. We use sensors available on the market and avoided to design specialized sensors in ASIC technologies. We employ standard radio protocol and open source projects when it was achieved. The specific contributions of the PhD research activities are presented and discussed in the following. • We have designed and build several wireless sensor node providing both sensing and actuator capability making the focus on the flexibility, small form factor and low power consumption. The key idea was to develop a simple and general purpose architecture for rapid analysis, prototyping and deployment of BAN solutions. Two different sensing units are integrated: kinematic (3D accelerometer and 3D gyroscopes) and kinetic (foot-floor contact pressure forces). Two kind of feedbacks were implemented: audio and vibrotactile. • Since the system built is a suitable platform for testing and measuring the features and the constraints of a sensor network (radio communication, network protocols, power consumption and autonomy), we made a comparison between Bluetooth and ZigBee performance in terms of throughput and energy efficiency. Test in the field evaluate the usability in the fall detection scenario. • To prove the flexibility of the architecture designed, we have implemented a wearable system for human posture rehabilitation. The application was developed in conjunction with biomedical engineers who provided the audio-algorithms to furnish a biofeedback to the user about his/her stability. • We explored off-line gait analysis of collected data, developing an algorithm to detect foot inclination in the sagittal plane, during walk. • In collaboration with the Wearable Lab – ETH, Zurich, we developed an algorithm to monitor the user during several walking condition where the user carry a load. The remainder of the thesis is organized as follows. Chapter I gives an overview about Body Area Networks (BANs), illustrating the relevant features of this technology and the key challenges still open. It concludes with a short list of the real solutions and prototypes proposed by academic research and manufacturers. The domain of the posture and gait analysis, the methodologies, and the technologies used to provide real-time feedback on detected events, are illustrated in Chapter II. The Chapter III and IV, respectively, shown BANs developed with the purpose to detect fall and monitor the gait taking advantage by two inertial measurement unit and baropodometric insoles. Chapter V reports an audio-biofeedback system to improve balance on the information provided by the use centre of mass. A walking assistant based on the KNN classifier to detect walking alteration on load carriage, is described in Chapter VI.

Light energy management in peach: utilization, photoprotection , photodamage and recovery. Maximizing light absorption in orchard is not always the best solution

The relation between the intercepted light and orchard productivity was considered linear, although this dependence seems to be more subordinate to planting system rather than light intensity. At whole plant level not always the increase of irradiance determines productivity improvement. One of the reasons can be the plant intrinsic un-efficiency in using energy. Generally in full light only the 5 – 10% of the total incoming energy is allocated to net photosynthesis. Therefore preserving or improving this efficiency becomes pivotal for scientist and fruit growers. Even tough a conspicuous energy amount is reflected or transmitted, plants can not avoid to absorb photons in excess. The chlorophyll over-excitation promotes the reactive species production increasing the photoinhibition risks. The dangerous consequences of photoinhibition forced plants to evolve a complex and multilevel machine able to dissipate the energy excess quenching heat (Non Photochemical Quenching), moving electrons (water-water cycle , cyclic transport around PSI, glutathione-ascorbate cycle and photorespiration) and scavenging the generated reactive species. The price plants must pay for this equipment is the use of CO2 and reducing power with a consequent decrease of the photosynthetic efficiency, both because some photons are not used for carboxylation and an effective CO2 and reducing power loss occurs. Net photosynthesis increases with light until the saturation point, additional PPFD doesn’t improve carboxylation but it rises the efficiency of the alternative pathways in energy dissipation but also ROS production and photoinhibition risks. The wide photo-protective apparatus, although is not able to cope with the excessive incoming energy, therefore photodamage occurs. Each event increasing the photon pressure and/or decreasing the efficiency of the described photo-protective mechanisms (i.e. thermal stress, water and nutritional deficiency) can emphasize the photoinhibition. Likely in nature a small amount of not damaged photosystems is found because of the effective, efficient and energy consuming recovery system. Since the damaged PSII is quickly repaired with energy expense, it would be interesting to investigate how much PSII recovery costs to plant productivity. This PhD. dissertation purposes to improve the knowledge about the several strategies accomplished for managing the incoming energy and the light excess implication on photo-damage in peach. The thesis is organized in three scientific units. In the first section a new rapid, non-intrusive, whole tissue and universal technique for functional PSII determination was implemented and validated on different kinds of plants as C3 and C4 species, woody and herbaceous plants, wild type and Chlorophyll b-less mutant and monocot and dicot plants. In the second unit, using a “singular” experimental orchard named “Asymmetric orchard”, the relation between light environment and photosynthetic performance, water use and photoinhibition was investigated in peach at whole plant level, furthermore the effect of photon pressure variation on energy management was considered on single leaf. In the third section the quenching analysis method suggested by Kornyeyev and Hendrickson (2007) was validate on peach. Afterwards it was applied in the field where the influence of moderate light and water reduction on peach photosynthetic performances, water requirements, energy management and photoinhibition was studied. Using solar energy as fuel for life plant is intrinsically suicidal since the high constant photodamage risk. This dissertation would try to highlight the complex relation existing between plant, in particular peach, and light analysing the principal strategies plants developed to manage the incoming light for deriving the maximal benefits as possible minimizing the risks. In the first instance the new method proposed for functional PSII determination based on P700 redox kinetics seems to be a valid, non intrusive, universal and field-applicable technique, even because it is able to measure in deep the whole leaf tissue rather than the first leaf layers as fluorescence. Fluorescence Fv/Fm parameter gives a good estimate of functional PSII but only when data obtained by ad-axial and ab-axial leaf surface are averaged. In addition to this method the energy quenching analysis proposed by Kornyeyev and Hendrickson (2007), combined with the photosynthesis model proposed by von Caemmerer (2000) is a forceful tool to analyse and study, even in the field, the relation between plant and environmental factors such as water, temperature but first of all light. “Asymmetric” training system is a good way to study light energy, photosynthetic performance and water use relations in the field. At whole plant level net carboxylation increases with PPFD reaching a saturating point. Light excess rather than improve photosynthesis may emphasize water and thermal stress leading to stomatal limitation. Furthermore too much light does not promote net carboxylation improvement but PSII damage, in fact in the most light exposed plants about 50-60% of the total PSII is inactivated. At single leaf level, net carboxylation increases till saturation point (1000 – 1200 μmolm-2s-1) and light excess is dissipated by non photochemical quenching and non net carboxylative transports. The latter follows a quite similar pattern of Pn/PPFD curve reaching the saturation point at almost the same photon flux density. At middle-low irradiance NPQ seems to be lumen pH limited because the incoming photon pressure is not enough to generate the optimum lumen pH for violaxanthin de-epoxidase (VDE) full activation. Peach leaves try to cope with the light excess increasing the non net carboxylative transports. While PPFD rises the xanthophyll cycle is more and more activated and the rate of non net carboxylative transports is reduced. Some of these alternative transports, such as the water-water cycle, the cyclic transport around the PSI and the glutathione-ascorbate cycle are able to generate additional H+ in lumen in order to support the VDE activation when light can be limiting. Moreover the alternative transports seems to be involved as an important dissipative way when high temperature and sub-optimal conductance emphasize the photoinhibition risks. In peach, a moderate water and light reduction does not determine net carboxylation decrease but, diminishing the incoming light and the environmental evapo-transpiration request, stomatal conductance decreases, improving water use efficiency. Therefore lowering light intensity till not limiting levels, water could be saved not compromising net photosynthesis. The quenching analysis is able to partition absorbed energy in the several utilization, photoprotection and photo-oxidation pathways. When recovery is permitted only few PSII remained un-repaired, although more net PSII damage is recorded in plants placed in full light. Even in this experiment, in over saturating light the main dissipation pathway is the non photochemical quenching; at middle-low irradiance it seems to be pH limited and other transports, such as photorespiration and alternative transports, are used to support photoprotection and to contribute for creating the optimal trans-thylakoidal ΔpH for violaxanthin de-epoxidase. These alternative pathways become the main quenching mechanisms at very low light environment. Another aspect pointed out by this study is the role of NPQ as dissipative pathway when conductance becomes severely limiting. The evidence that in nature a small amount of damaged PSII is seen indicates the presence of an effective and efficient recovery mechanism that masks the real photodamage occurring during the day. At single leaf level, when repair is not allowed leaves in full light are two fold more photoinhibited than the shaded ones. Therefore light in excess of the photosynthetic optima does not promote net carboxylation but increases water loss and PSII damage. The more is photoinhibition the more must be the photosystems to be repaired and consequently the energy and dry matter to allocate in this essential activity. Since above the saturation point net photosynthesis is constant while photoinhibition increases it would be interesting to investigate how photodamage costs in terms of tree productivity. An other aspect of pivotal importance to be further widened is the combined influence of light and other environmental parameters, like water status, temperature and nutrition on peach light, water and phtosyntate management.

Second law analysis and simulation techniques for the energy optimization of buildings

The research activity described in this thesis is focused mainly on the study of finite-element techniques applied to thermo-fluid dynamic problems of plant components and on the study of dynamic simulation techniques applied to integrated building design in order to enhance the energy performance of the building. The first part of this doctorate thesis is a broad dissertation on second law analysis of thermodynamic processes with the purpose of including the issue of the energy efficiency of buildings within a wider cultural context which is usually not considered by professionals in the energy sector. In particular, the first chapter includes, a rigorous scheme for the deduction of the expressions for molar exergy and molar flow exergy of pure chemical fuels. The study shows that molar exergy and molar flow exergy coincide when the temperature and pressure of the fuel are equal to those of the environment in which the combustion reaction takes place. A simple method to determine the Gibbs free energy for non-standard values of the temperature and pressure of the environment is then clarified. For hydrogen, carbon dioxide, and several hydrocarbons, the dependence of the molar exergy on the temperature and relative humidity of the environment is reported, together with an evaluation of molar exergy and molar flow exergy when the temperature and pressure of the fuel are different from those of the environment. As an application of second law analysis, a comparison of the thermodynamic efficiency of a condensing boiler and of a heat pump is also reported. The second chapter presents a study of borehole heat exchangers, that is, a polyethylene piping network buried in the soil which allows a ground-coupled heat pump to exchange heat with the ground. After a brief overview of low-enthalpy geothermal plants, an apparatus designed and assembled by the author to carry out thermal response tests is presented. Data obtained by means of in situ thermal response tests are reported and evaluated by means of a finite-element simulation method, implemented through the software package COMSOL Multyphysics. The simulation method allows the determination of the precise value of the effective thermal properties of the ground and of the grout, which are essential for the design of borehole heat exchangers. In addition to the study of a single plant component, namely the borehole heat exchanger, in the third chapter is presented a thorough process for the plant design of a zero carbon building complex. The plant is composed of: 1) a ground-coupled heat pump system for space heating and cooling, with electricity supplied by photovoltaic solar collectors; 2) air dehumidifiers; 3) thermal solar collectors to match 70% of domestic hot water energy use, and a wood pellet boiler for the remaining domestic hot water energy use and for exceptional winter peaks. This chapter includes the design methodology adopted: 1) dynamic simulation of the building complex with the software package TRNSYS for evaluating the energy requirements of the building complex; 2) ground-coupled heat pumps modelled by means of TRNSYS; and 3) evaluation of the total length of the borehole heat exchanger by an iterative method developed by the author. An economic feasibility and an exergy analysis of the proposed plant, compared with two other plants, are reported. The exergy analysis was performed by considering the embodied energy of the components of each plant and the exergy loss during the functioning of the plants.

Dynamic thermal performance of building components and application to the experimental and theoretical analysis of a ventilated façade

The general aim of this work is to contribute to the energy performance assessment of ventilated façades by the simultaneous use of experimental data and numerical simulations. A significant amount of experimental work was done on different types of ventilated façades with natural ventilation. The measurements were taken on a test building. The external walls of this tower are rainscreen ventilated façades. Ventilation grills are located at the top and at the bottom of the tower. In this work the modelling of the test building using a dynamic thermal simulation program (ESP-r) is presented and the main results discussed. In order to investigate the best summer thermal performance of rainscreen ventilated skin façade a study for different setups of rainscreen walls was made. In particular, influences of ventilation grills, air cavity thickness, skin colour, skin material, orientation of façade were investigated. It is shown that some types of rainscreen ventilated façade typologies are capable of lowering the cooling energy demand of a few percent points.

La sostenibilità ambientale dal Progetto Edilizio al Piano Urbano: L'integrazione della variabile energetica nella pianificazione del territorio

La questione energetica ha assunto, negli ultimi anni, un ruolo centrale nel dibattito mondiale in relazione a quattro fattori principali: la non riproducibilità delle risorse naturali, l’aumento esponenziale dei consumi, gli interessi economici e la salvaguardia dell'equilibrio ambientale e climatico del nostro Pianeta. E’ necessario, dunque, cambiare il modello di produzione e consumo dell’energia soprattutto nelle città, dove si ha la massima concentrazione dei consumi energetici. Per queste ragioni, il ricorso alle Fonti Energetiche Rinnovabili (FER) si configura ormai come una misura necessaria, opportuna ed urgente anche nella pianificazione urbanistica. Per migliorare la prestazione energetica complessiva del sistema città bisogna implementare politiche di governo delle trasformazioni che escano da una logica operativa “edificio-centrica” e ricomprendano, oltre al singolo manufatto, le aggregazioni di manufatti e le loro relazioni/ interazioni in termini di input e output materico-energetiche. La sostituzione generalizzata del patrimonio edilizio esistente con nuovi edifici iper-tecnologici, è improponibile. In che modo quindi, è possibile ridefinire la normativa e la prassi urbanistica per generare tessuti edilizi energeticamente efficienti? La presente ricerca propone l’integrazione tra la nascente pianificazione energetica del territorio e le più consolidate norme urbanistiche, nella generazione di tessuti urbani “energy saving” che aggiungano alle prestazioni energetico-ambientali dei singoli manufatti quelle del contesto, in un bilancio energetico complessivo. Questo studio, dopo aver descritto e confrontato le principali FER oggi disponibili, suggerisce una metodologia per una valutazione preliminare del mix di tecnologie e di FER più adatto per ciascun sito configurato come “distretto energetico”. I risultati di tale processo forniscono gli elementi basilari per predisporre le azioni necessarie all’integrazione della materia energetica nei Piani Urbanistici attraverso l’applicazione dei principi della perequazione nella definizione di requisiti prestazionali alla scala insediativa, indispensabili per un corretto passaggio alla progettazione degli “oggetti” e dei “sistemi” urbani.

Temperature Variation Aware Energy Optimization in Heterogeneous MPSoCs

Thermal effects are rapidly gaining importance in nanometer heterogeneous integrated systems. Increased power density, coupled with spatio-temporal variability of chip workload, cause lateral and vertical temperature non-uniformities (variations) in the chip structure. The assumption of an uniform temperature for a large circuit leads to inaccurate determination of key design parameters. To improve design quality, we need precise estimation of temperature at detailed spatial resolution which is very computationally intensive. Consequently, thermal analysis of the designs needs to be done at multiple levels of granularity. To further investigate the flow of chip/package thermal analysis we exploit the Intel Single Chip Cloud Computer (SCC) and propose a methodology for calibration of SCC on-die temperature sensors. We also develop an infrastructure for online monitoring of SCC temperature sensor readings and SCC power consumption. Having the thermal simulation tool in hand, we propose MiMAPT, an approach for analyzing delay, power and temperature in digital integrated circuits. MiMAPT integrates seamlessly into industrial Front-end and Back-end chip design flows. It accounts for temperature non-uniformities and self-heating while performing analysis. Furthermore, we extend the temperature variation aware analysis of designs to 3D MPSoCs with Wide-I/O DRAM. We improve the DRAM refresh power by considering the lateral and vertical temperature variations in the 3D structure and adapting the per-DRAM-bank refresh period accordingly. We develop an advanced virtual platform which models the performance, power, and thermal behavior of a 3D-integrated MPSoC with Wide-I/O DRAMs in detail. Moving towards real-world multi-core heterogeneous SoC designs, a reconfigurable heterogeneous platform (ZYNQ) is exploited to further study the performance and energy efficiency of various CPU-accelerator data sharing methods in heterogeneous hardware architectures. A complete hardware accelerator featuring clusters of OpenRISC CPUs, with dynamic address remapping capability is built and verified on a real hardware.

Modellazione edilizia e simulazione energetica per le analisi delle prestazioni e la progettazione integrata delle cantine aziendali

Il presente studio si colloca nell’ambito di una ricerca il cui obiettivo è la formulazione di criteri progettuali finalizzati alla ottimizzazione delle prestazioni energetiche delle cantine di aziende vitivinicole con dimensioni produttive medio-piccole. Nello specifico la ricerca si pone l’obiettivo di individuare degli indicatori che possano valutare l’influenza che le principali variabili progettuali hanno sul fabbisogno energetico dell’edificio e sull’andamento delle temperature all’interno dei locali di conservazione ed invecchiamento del vino. Tali indicatori forniscono informazioni sulla prestazione energetica dell’edificio e sull’idoneità dei locali non climatizzati finalizzata alla conservazione del vino Essendo la progettazione una complessa attività multidisciplinare, la ricerca ha previsto l’ideazione di un programma di calcolo in grado di gestire ed elaborare dati provenienti da diversi ambiti (ingegneristici, architettonici, delle produzioni agroindustriali, ecc.), e di restituire risultati sintetici attraverso indicatori allo scopo individuati. Il programma è stato applicato su un caso-studio aziendale rappresentativo del settore produttivo. Sono stati vagliati gli effetti di due modalità di vendemmia e di quattro soluzioni architettoniche differenti. Le soluzioni edilizie derivano dalla combinazione di diversi isolamenti termici e dalla presenza o meno di locali interrati. Per le analisi sul caso-studio ci si è avvalsi di simulazioni energetiche in regime dinamico, supportate e validate da campagne di monitoraggio termico e meteorologico all’interno dell’azienda oggetto di studio. I risultati ottenuti hanno evidenziato come il programma di calcolo concepito nell’ambito di questo studio individui le criticità dell’edificio in termini energetici e di “benessere termico” del vino e consenta una iterativa revisione delle variabili progettuale indagate. Esso quindi risulta essere uno strumento informatizzato di valutazione a supporto della progettazione, finalizzato ad una ottimizzazione del processo progettuale in grado di coniugare, in maniera integrata, gli obiettivi della qualità del prodotto, della efficienza produttiva e della sostenibilità economica ed ambientale.

Sulla ricerca del minimo dei consumi per vetture sportive

La ricerca oggetto di questa tesi, come si evince dal titolo stesso, è volta alla riduzione dei consumi per vetture a forte carattere sportivo ed elevate prestazioni specifiche. In particolare, tutte le attività descritte fanno riferimento ad un ben definito modello di vettura, ovvero la Maserati Quattroporte. Lo scenario all’interno del quale questo lavoro si inquadra, è quello di una forte spinta alla riduzione dei cosiddetti gas serra, ossia dell’anidride carbonica, in linea con quelle che sono le disposizioni dettate dal protocollo di Kyoto. La necessità di ridurre l’immissione in atmosfera di CO2 sta condizionando tutti i settori della società: dal riscaldamento degli edifici privati a quello degli stabilimenti industriali, dalla generazione di energia ai processi produttivi in senso lato. Nell’ambito di questo panorama, chiaramente, sono chiamati ad uno sforzo considerevole i costruttori di automobili, alle quali è imputata una percentuale considerevole dell’anidride carbonica prodotta ogni giorno e riversata nell’atmosfera. Al delicato problema inquinamento ne va aggiunto uno forse ancor più contingente e diretto, legato a ragioni di carattere economico. I combustibili fossili, come tutti sanno, sono una fonte di energia non rinnovabile, la cui disponibilità è legata a giacimenti situati in opportune zone del pianeta e non inesauribili. Per di più, la situazione socio politica che il medio oriente sta affrontando, unita alla crescente domanda da parte di quei paesi in cui il processo di industrializzazione è partito da poco a ritmi vertiginosi, hanno letteralmente fatto lievitare il prezzo del petrolio. A causa di ciò, avere una vettura efficiente in senso lato e, quindi, a ridotti consumi, è a tutti gli effetti un contenuto di prodotto apprezzato dal punto di vista del marketing, anche per i segmenti vettura più alti. Nell’ambito di questa ricerca il problema dei consumi è stato affrontato come una conseguenza del comportamento globale della vettura in termini di efficienza, valutando il miglior compromesso fra le diverse aree funzionali costituenti il veicolo. Una parte consistente del lavoro è stata dedicata alla messa a punto di un modello di calcolo, attraverso il quale eseguire una serie di analisi di sensibilità sull’influenza dei diversi parametri vettura sul consumo complessivo di carburante. Sulla base di tali indicazioni, è stata proposta una modifica dei rapporti del cambio elettro-attuato con lo scopo di ottimizzare il compromesso tra consumi e prestazioni, senza inficiare considerevolmente queste ultime. La soluzione proposta è stata effettivamente realizzata e provata su vettura, dando la possibilità di verificare i risultati ed operare un’approfondita attività di correlazione del modello di calcolo per i consumi. Il beneficio ottenuto in termini di autonomia è stato decisamente significativo con riferimento sia ai cicli di omologazione europei, che a quelli statunitensi. Sono state inoltre analizzate le ripercussioni dal punto di vista delle prestazioni ed anche in questo caso i numerosi dati rilevati hanno permesso di migliorare il livello di correlazione del modello di simulazione per le prestazioni. La vettura con la nuova rapportatura proposta è stata poi confrontata con un prototipo di Maserati Quattroporte avente cambio automatico e convertitore di coppia. Questa ulteriore attività ha permesso di valutare il differente comportamento tra le due soluzioni, sia in termini di consumo istantaneo, che di consumo complessivo rilevato durante le principali missioni su banco a rulli previste dalle normative. L’ultima sezione del lavoro è stata dedicata alla valutazione dell’efficienza energetica del sistema vettura, intesa come resistenza all’avanzamento incontrata durante il moto ad una determinata velocità. Sono state indagate sperimentalmente le curve di “coast down” della Quattroporte e di alcune concorrenti e sono stati proposti degli interventi volti alla riduzione del coefficiente di penetrazione aerodinamica, pur con il vincolo di non alterare lo stile vettura.