Influence of Different Base Thicknesses on Maxillary Complete Denture Processing: Linear and Angular Graphic Analysis on the Movement of Artificial Teeth

Objective: The purpose of this study was to compare the dental movement that occurs during the processing of maxillary complete dentures with 3 different base thicknesses, using 2 investment methods, and microwave polymerization.Methods: A sample of 42 denture models was randomly divided into 6 groups (n = 7), with base thicknesses of 1.25, 2.50, and 3.75 mm and gypsum or silicone flask investment. Points were demarcated on the distal surface of the second molars and on the back of the gypsum cast at the alveolar ridge level to allow linear and angular measurement using AutoCAD software. The data were subjected to analysis of variance with double factor, Tukey test and Fisher (post hoc).Results: Angular analysis of the varying methods and their interactions generated a statistical difference (P = 0.023) when the magnitudes of molar inclination were compared. Tooth movement was greater for thin-based prostheses, 1.25 mm (-0.234), versus thick 3.75 mm (0.2395), with antagonistic behavior. Prosthesis investment with silicone (0.053) showed greater vertical change compared with the gypsum investment (0.032). There was a difference between the point of analysis, demonstrating that the changes were not symmetric.Conclusions: All groups evaluated showed change in the position of artificial teeth after processing. The complete denture with a thin base (1.25 mm) and silicone investment showed the worst results, whereas intermediate thickness (2.50 mm) was demonstrated to be ideal for the denture base.

Gravitational and quantum bounds on the photon mass

Conselho Nacional de Desenvolvimento Científico e Tecnológico (CNPq)

Upper bounds on the photon mass

Conselho Nacional de Desenvolvimento Científico e Tecnológico (CNPq)

Consequences of quadratic frictional force on the one dimensional bouncing ball model

Some dynamical properties of the one dimensional Fermi accelerator model, under the presence of frictional force are studied. The frictional force is assumed as being proportional to the square particle's velocity. The problem is described by use of a two dimensional non linear mapping, therefore obtained via the solution of differential equations. We confirm that the model experiences contraction of the phase space area and in special, we characterized the behavior of the particle approaching an attracting fixed point. © 2007 American Institute of Physics.

Influence of extracts of Stryphnodendron polyphyllum Mart. and Stryphnodendron obovatum Benth. on the cicatrisation of cutaneous wounds in rats

Stem bark of the two species Stryphnodendron polyphyllum Mart. and Stryphnodendron obovatum Benth., Leguminosae, was investigated for wound healing, antibacterial and antioxidant activity. These plants contain 12 and 19% tannins in their stem bark, respectively, and are widely used in traditional medicine in Brazil. The total content of phenolics of the crude extract (CE) of Stryphnodendron obovatum was 76.95 +/- 2.98% (CV = 3.87%) and of the ethyl-acetate fraction (EAF) was 89.13 +/- 0.34% (CV = 0.38%); whereas in Stryphnodendron polyphyllum the CE phenolics content was 51.62 +/- 1.53% (CV = 2.96%) and the EAF phenolics content was 59.00 +/- 1.91% (CV = 3.24%). The tannin content of CE from Stryphnodendron obovatum [36.58 +/- 0.35% (CV = 0.98%)] was about 11% higher than in CE from Stryphnodendron polyphyllum [25.43 +/- 0.96% (CV = 3.77%)]. The difference between the species was even greater in the EAF: in Stryphnodendron obovatum the EAF phenolics content was 55.01 +/- 0.36% (CV = 0.65%), whereas in Stryphnodendron polyphyllum the content was 36.16 +/- 0.42% (CV = 1.16%). The healing effect of ointments containing 2.5% crude lyophilised extract (PCE) and 2.5% ethyl-acetate lyophilised fraction (PEA) of the stem bark of Stryphnodendron polyphyllum and Stryphnodendron obovatum was studied in cutaneous wounds of Wistar((R)) rats after 4, 7 and 10 days of treatment. Epithelial cell proliferation in the area of re-epithelialisation of the wounds was evaluated by counting the metaphases blocked by vincristine sulfate. With PCE an increase in epidermal growth was observed after 4 and 7 days of treatment with Stryphnodendron polyphyllum, and after 7 and 10 days of treatment with Stryphnodendron obovatum. Wounds treated with PEA of Stryphnodendron obovatum showed increased epidermal growth only 4 days after the treatment, for Stryphnodendron polyphyllum, epidermal growth was observed after 4 and 7 days of treatment. Both the CE and the EAF fractions of Stryphnodendron polyphyllum and Stryphnodendron obovatum showed antibacterial activity against Staphylococcus aureus with MIC values of 125 and 250 mu g/ml, respectively. Gram-negative bacteria tested were not inhibited by extracts and fractions at concentrations > 1000 mu g/ml. The antioxidant activity through reduction of the DPPH radical in TLC, confirmed the anti-radical properties of these extracts in both species. CE and EAF of both species showed a radical scavenging activity (RSA) and protected DPPH from discolouration, already at 0.032 mu g/ml. The extract from Stryphnodendron polyphyllum were more effective than those Stryphnodendron obovatum, although the former had a lower tannin content. (c) 2005 Elsevier B.V.. All rights reserved.

Effect of the addition of soy lecithin and Yucca schidigera extract on the properties of gelatin and glycerol based biodegradable films

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Effect of filling technique and root canal area on the percentage of gutta-percha in laterally compacted root fillings

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Effect of Airborne-Particle Abrasion and Mechanico-Thermal Cycling on the Flexural Strength of Glass Ceramic Fused to Gold or Cobalt-Chromium Alloy

Purpose: To evaluate the effect of airborne-particle abrasion and mechanico-thermal cycling on the flexural strength of a ceramic fused to cobalt-chromium alloy or gold alloy.Materials and Methods: Metallic bars (n = 120) were made (25 mm x 3 mm x 0.5 mm): 60 with gold alloy and 60 with Co-Cr. At the central area of the bars (8 mm x 3 mm), a layer of opaque ceramic and then two layers of glass ceramic (Vita VM13, Vita Zahnfabrick) were fired onto it (thickness: 1 mm). Ten specimens from each alloy group were randomly allocated to a surface treatment [(tungsten bur or air-particle abrasion (APA) with Al(2)O(3) at 10 mm or 20 mm away)] and mechanico-thermal cycling (no cycling or mechanically loaded 20,000 cycles; 10 N distilled water at 37 degrees C and then thermocycled 3000 cycles; 5 degrees C to 55 degrees C, dwell time 30 seconds) combination. Those specimens that did not undergo mechanico-thermal cyclingwere stored inwater (37 degrees C) for 24 hours. Bond strength was measured using a three-point bend test, according to ISO 9693. After the flexural strength test, failure types were noted. The data were analyzed using three factor-ANOVA and Tukey's test (alpha = 0.05).Results: There were no significant differences between the flexural bond strength of gold and Co-Cr groups (42.64 +/- 8.25 and 43.39 +/- 10.89 MPa, respectively). APA 10 and 20 mm away surface treatment (45.86 +/- 9.31 and 46.38 +/- 8.89 MPa, respectively) had similar mean flexural strength values, and both had significantly higher bond strength than tungsten bur treatment (36.81 +/- 7.60 MPa). Mechanico-thermal cycling decreased the mean flexural strength values significantly for all six alloy-surface treatment combinations tested when compared to the control groups. The failure type was adhesive in the metal/ceramic interface for specimens surface treated only with the tungsten bur, and mixed for specimens surface treated with APA 10 and 20 mm.Conclusions: Considering the levels adopted in this study, the alloy did not affect the bond strength; APA with Al(2)O(3) at 10 and 20 mm improved the flexural bond strength between ceramics and alloys used, and the mechanico-thermal cycling of metal-ceramic specimens resulted in a decrease of bond strength.

The effect of porcelain thickness and surface liner application on the fracture behavior of a ceramic system

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Mechanical and thermal cycling effects on the flexural strength of glass ceramics fused to titanium

This study evaluated the effects of mechanical and thermal cycling on the flexural strength (ISO 9693) of three brands of ceramics fused to commercially pure titanium (cpTi). Metallic frameworks of 25 x 3 x 0.5 mm dimensions (N = 84) were cast in cpTi, followed by 150-mu m aluminum oxide airborne particle abrasion at a designated area of the frameworks (8 x 3 mm). Bonder and opaque ceramic were applied on the frameworks, and then the corresponding ceramic (Triceram, Super Porcelain Ti-22, Vita Titankeramik) was fired onto them (thickness: 1 mm). Half of the specimens from each ceramic-metal combination were randomly tested without aging (only water storage at 37 degrees C for 24 hours), while the other half were mechanically loaded (20,000 cycles under 10 N load, immersion in distilled water at 37 degrees C) and thermocycled (3,000 cycles, between 5-55 degrees C, dwell time of 13 seconds). After the flexural strength test, failure types were noted. Mechanical and thermal cycling decreased the mean flexural strength values significantly (p<0.05) for all the three ceramic-cpTi combinations tested when compared to the control group. In all the three groups, failure type was exclusively adhesive at the opaque ceramic-cpTi interfacial zone with no presence of ceramic on the substrate surface except for a visible oxide layer.

Bounds on direct couplings of superheavy metastable particles to the inflaton field from ultra high energy cosmic ray events

Top-down models for the origin of ultra high energy cosmic rays (UHECR's) propose that these events are the decay products of relic superheavy metastable particles, usually called X particles. These particles can be produced in the reheating period following the inflationary epoch of the early Universe. We obtain constraints on some parameters such as the lifetime and direct couplings of the X-particle to the inflaton field from the requirement that they are responsible for the observed UHECR flux.

Hq(4) symmetry: the linear q-harmonic oscillator based on generalized irreps of the q-deformed Heisenberg algebra

Conselho Nacional de Desenvolvimento Científico e Tecnológico (CNPq)

Temperature and meal size effects on the postprandial metabolism and energetics in a boid snake

We investigated the combined effect of meal size and temperature on the aerobic metabolism and energetics of digestion in Boa constrictor amarali. Oxygen uptake rates ((V) over dot o(2)) and the. duration of the digestion were determined in snakes fed with meals equaling to 5%, 10%, 20%, and 40% of the snake's body mass at 25degrees and 30 degreesC. The maximum (V) over dot o(2) values attained during digestion were greater at 30 degreesC than at 25 degreesC. Both maximal (V) over dot (o2) values and the duration of the specific dynamic action. (SDA) were attained sooner at 30 degreesC than at 25 degreesC. Therefore, the temperature effect on digestion in Boa is characterized by the shortening of the SDA duration at the expense of increased. Energy allocated to SDA was not affected by meal size but. was greater at 25 degreesC compared to 30 degreesC. This indicates that a postprandial thermophilic response can be advantageous not only by decreasing the duration of digestion but also by improving digestive efficiency. Maximal (V) over dot o(2) and SDA duration. increased with meal size at both temperatures.

SZEGO and PARA-ORTHOGONAL POLYNOMIALS on THE REAL LINE: ZEROS and CANONICAL SPECTRAL TRANSFORMATIONS

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

The Effect of Water Immersion and UV Radiation Aging on the Shear Behavior of Woven Continuous Fiber/PEI Laminates

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)