Design of a LNA and a Gilbert Cell Mixer MMICs with a GaAs PHEMT technology

The design of a Gilbert Cell Mixer and a low noise amplifier (LNA), using GaAs PHEMT technology is presented. The compatibility is shown for co-integration of both block on the same chip, to form a high performance 1.9 GHz receiver front-end. The designed LNA shows 9.23 dB gain and 2.01 dB noise figure (NF). The mixer is designed to operate at RF=1.9 GHz, LO=2.0 GHz and IF=100 MHz with a gain of 14.3 dB and single sideband noise figure (SSB NF) of 9.6 dB. The mixer presents a bandwith of 8 GHz.

An analog implementation of radial basis neural networks (RBNN) using BiCMOS technology

This paper describes a analog implementation of radial basis neural networks (RBNN) in BiCMOS technology. The RBNN uses a gaussian function obtained through the characteristic of the bipolar differential pair. The gaussian parameters (gain, center and width) is changed with programmable current source. Results obtained with PSPICE software is showed.

Farming technology, biochemistry characterization, and protective effects of culinary-medicinal mushrooms Agaricus brasiliensis S. Wasser et al. and Lentinus edodes (Berk.) Singer: Five years of research in Brazil

The biotechnology, biochemical characterization, and protective effects of the himematsutake and shiitake mushrooms were studied for the Thematic Project, from 1998 to 2003. A new species, Agaricus Brasiliens is Wasser et al. (= A. blazei Murrill ss. Heinem.), was proposed for the cultivated lineages in Brazil. Interactions among lineages, substrates, casing layers, and fructification inductions (temperature alternations) significantly increased the productivity of A. brasiliensis in Brazil (from 40 g to 200 g of fresh mushroom kg -1 moist compost). However, pests and diseases (mainly Sciaridae flies and false truffle), drastically reduced the productivity of A. brasiliensis (below 50 g kg -1). Biochemically for each mushroom species, the polar extracts, no polars, and medium polarity presented the same organic substances; however, their concentrations differed as a result of the lineages, maturation of the fruit bodies, and cultivation conditions. In this aspect, concentration of linoleic acid in A. brasiliensis (added to animal food) was related directly to the chemical protection against carcinogenic drugs in mice. Aqueous extracts of Lentinus edodes (= Lentinula edodes (Berk.) Pegler) and A. brasiliensis may be preventive chemical protectors against mutagenic and carcinogenic drugs, depending on the lineage and extraction method (tea or juice). However, immunomodulator effects and tumor reduction were only observed with concentrated fractions (hexanic, methanolic, and ATF extracts). Aqueous extracts of A. brasiliensis and L. edodes have antibiotic-like substances and substances able to act as elicitors of resistance responses in some plants (local and systemic) and show a potential to be used in the alternative control of plant pathogens. © 2005 by Begell House, Inc.

Cutting characteristics of dental diamond burs made with CVD technology

The aim of this study was to determine the cutting ability of chemical vapor deposition (CVD) diamond burs coupled to an ultrasonic dental unit handpiece for minimally invasive cavity preparation. One standard cavity was prepared on the mesial and distal surfaces of 40 extracted human third molars either with cylindrical or with spherical CVD burs. The cutting ability was compared regarding type of substrate (enamel and dentin) and direction of handpiece motion. The morphological characteristics, width and depth of the cavities were analyzed and measured using scanning electron micrographs. Statistical analysis using the Kruskal-Wallis test (p < 0.05) revealed that the width and depth of the cavities were significantly greater when they were prepared on dentin. Wider cavities were prepared when the cylindrical CVD bur was used, and deeper cavities resulted from preparation with the spherical CVD bur. The direction of handpiece motion did not influence the size of the cavities, and the CVD burs produced precise and conservative cutting.

Bio-safety technology in production of bovine herpesvirus type 5 (BoHV-5) using an alternative serum-free medium

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

A methodology and a tool to design of mixed-signal technology

This paper presents a tool box developed to read files describing a SIMULINK® model and translates it into a structural VHDL-AMS description. In translation process, all files and directory structures to simulate the translated model on SystemVision™ environment is generate. The tool box named MS2SV was tested by three models of commercially available digital-to-analogue converters. All models use the R2R ladder network to conversion, but the functionality of these three components is different. The methodology of conversion of the model is presents together with sort theory about R-2R ladder network. In the evaluation of the translated models, we used a sine waveform input signal and the waveform generated by D/A conversion process was compared by FFT analysis. The results show the viability of this type of approach. This work considers some of challenges set by the electronic industry for the further development of simulation methodologies and tools in the field of mixed-signal technology. © 2007 IEEE.

Estimation of electrical machine speed using sensorless technology and neural networks

The use of sensorless technologies is an increasing tendency on industrial drivers for electrical machines. The estimation of electrical and mechanical parameters involved with the electrical machine control is used very frequently in order to avoid measurement of all variables related to this process. The cost reduction may also be considered in industrial drivers, besides the increasing robustness of the system, as an advantage of the use of sensorless technologies. This work proposes the use of a recurrent artificial neural network to estimate the speed of induction motor for sensorless control schemes using one single current sensor. Simulation and experimental results are presented to validate the proposed approach. ©2008 IEEE.

Technology assessment for power quality mitigation devices - Micro-DVR case study

This work presents a case study on technology assessment for power quality devices. A system compatibility test protocol for power quality mitigation devices was developed in order to evaluate the functionality of three-phase voltage restoration devices. In order to case test this test protocol, a development platform with reduced power for DVR (Dynamic Voltage Restorer), the Micro-DVR, was tested, and results were discussed based on voltage disturbances standards. ©2008 IEEE.

Malware distributed collection and pre-classification system using honeypot technology

Malware has become a major threat in the last years due to the ease of spread through the Internet. Malware detection has become difficult with the use of compression, polymorphic methods and techniques to detect and disable security software. Those and other obfuscation techniques pose a problem for detection and classification schemes that analyze malware behavior. In this paper we propose a distributed architecture to improve malware collection using different honeypot technologies to increase the variety of malware collected. We also present a daemon tool developed to grab malware distributed through spam and a pre-classification technique that uses antivirus technology to separate malware in generic classes. © 2009 SPIE.

Supply Chain Management practices in the electro-electronics sector in Brazil: Evolutionary approach, information technology adoption and management actions

This paper examines the current level of adoption of Supply Chain Management (SCM) practices in the electro-electronic sector in Brazil and aims to identify the management and Information Technology (IT) actions that have been implemented to support the adoption of those practices. An e-mail survey was conducted. Descriptive statistics techniques were employed for data analysis. This study makes contributions to the electro-electronics sector and to the topics related to SCM, such as identifi cation and level of adoption of SCM practices. Another contribution of this research is the investigation of whether approaches such as Enterprise Resources Planning (ERP), Workshop with Customers, Electronic Data Interchange (EDI), Workshop with Suppliers and electronic Kanban are commonly used to support SCM practices. So far, this is the fi rst research on SCM practices in the electro-electronics sector in Brazil. Copyright © 2012 Inderscience Enterprises Ltd.

Unveiling fieldbus network technology through project-based learning

Fieldbus communications networks are a fundamental part of modern industrial automation technique. This paperwork presents an application of project-based learning (PBL) paradigm to help electrical engineering students grasp the major concepts of fieldbus networks, while attending a one-term long, elective microcontroller course. © 2012 IEEE.

Risk management in software projects through Knowledge Management techniques: Cases in Brazilian Incubated Technology-Based Firms

In businesses such as the software industry, which uses knowledge as a resource, activities are knowledge intensive, requiring constant adoption of new technologies and practices. Another feature of this environment is that the industry is particularly susceptible to failure; with this in mind, the objective of this research is to analyze the integration of Knowledge Management techniques into the activity of risk management as it applies to software development projects of micro and small Brazilian incubated technology-based firms. Research methods chosen were the Multiple Case Study. The main risk factor for managers and developers is that scope or goals are often unclear or misinterpreted. For risk management, firms have found that Knowledge Management techniques of conversion combination would be the most applicable for use; however, those most commonly used refer to the conversion mode as internalization.. © 2013 Elsevier Ltd. APM and IPMA.

Photodetection with gate-controlled lateral BJTs from standard CMOS technology

The silicon-based gate-controlled lateral bipolar junction transistor (BJT) is a controllable four-terminal photodetector with very high responsivity at low-light intensities. It is a hybrid device composed of a MOSFET, a lateral BJT, and a vertical BJT. Using sufficient gate bias to operate the MOS transistor in inversion mode, the photodetector allows for increasing the photocurrent gain by 106 at low light intensities when the base-emitter voltage is smaller than 0.4 V, and BJT is off. Two operation modes, with constant voltage bias between gate and emitter/source terminals and between gate and base/body terminals, allow for tuning the photoresponse from sublinear to slightly above linear, satisfying the application requirements for wide dynamic range, high-contrast, or linear imaging. MOSFETs from a standard 0.18-μm triple-well complementary-metal oxide semiconductor technology with a width to length ratio of 8 μm /2 μm and a total area of ∼ 500μm2 are used. When using this area, the responsivities are 16-20 kA/W. © 2001-2012 IEEE.

Influência da dopagem com oxigênio nas propriedades anelásticas e biocompatibilidade de ligas Ti-5%pNb e Ti-10%pNb

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)