Desenho e Construção de um protótipo gerador de jato de plasma frio a pressão atmosférica para aplicações biomédicas

Research for better performance materials in biomedical applications are constants. Thus recent studies aimed at the development of new techniques for modification of surfaces. The low pressure plasma has been highlighted for its versatility and for being environmentally friendly, achieving good results in the modification of physic chemical properties of materials. However, it is requires an expensive vacuum system and cannot able to generate superficial changes in specific regions. Furthermore, it is limits their use in polymeric materials and sensitive terms due to high process temperatures. Therefore, new techniques capable of generating cold plasma at atmospheric pressure (APPJ) were created. In order to perform surface treatments on biomaterials in specific regions was built a prototype capable of generating a cold plasma jet. The prototype plasma generator consists of a high voltage source, a support arm, sample port and a nozzle through which the ionized argon. The device was formed to a dielectric tube and two electrodes. This work was varied some parameters such as position between electrodes, voltage and electrical frequency to verify the behavior of glow discharges. The disc of titanium was polished and there was a surface modification. The power consumed, length, intensity and surface modifications of titanium were analyzed. The energy consumed during the discharges was observed by the Lissajous figure method. To check the length of the jets was realized with Image Pro Plus software. The modifications of the titanium surfaces were observed by optical microscopy (OM ) and atomic force microscopy (AFM ). The study showed that variations of the parameters such as voltage, frequency and geometric position between the electrodes influence the formation of the plasma jet. It was concluded that the plasma jet near room temperature and atmospheric pressure was able to cause modifications in titanium surface

O Gênero requerimento na perspectiva sociorretórica: análise da produção de graduandos no ambiente acadêmico-administrativo da UFRN

In administrative settings of public institutions, many activities are conducted through writing practices. Concerning this, writing is always connected to an activity we intend to perform. Among those practices, the genre request consists of an instrument through which the requirer addresses to an institution in order to request something under the support of legislation. Considering our work experience in a public institution of higher education, we elected - as object of our research - the genre request produced by undergraduates within the administrative domain of the Federal University of Rio Grande do Norte (UFRN) due to its importance in this context. For this, the theoretical framework adopted refers to the socio-rethorical conception of genre studies, which understands the genre as forms as rhetorically typified action (MILLER, 2009a; SWALES, 1990; BAZERMAN, 2009). Regarding methodology, it is a research associated to a qualitative approach (BODGAN; BIKLEN, 1994; CHIZZOTTI, 2010) whose discussion inserts into the field of Applied Linguistics. The data were generated from samples of requests and their users replies in questionnaires, interviews and verbal protocols of writing. The data analysis is based on the ethnographic methods of genre analysis postulated by Devitt, Reiff and Bawarshi (apud JOHNS et al., 2006). These analyses indicated that the requests are not always fully accomplished due to a lack of comprehension about the genre and its rhetorical situation on the part of the producers. It must probably happen - among other reasons - because these students may not have understood that several factors, such as: context, audience and purpose, affect the text production. We believe that one possibility to make the practice of this genre more efficient is to develop a more simple and practical way of elaborating requests, taking the needs imposed by the rhetorical situation as a basis

Interfaces cultural, política e organizacional do projeto caminhos do frio rota cultural no contexto da regionalização do turismo no brejo paraibano

This study is the analysis of cultural, political and organizational interfaces of "Caminhos do Frio Rota Cultural" Project in the context of tourism regionalization in Brejo Paraibano and it presents the characterization, routing and inventory of six municipalities of the Project, as well as the identification of cultural elements used for tourist in the routing of the pond, the investigation of political and organizational articulation and the verification of participation of each producing agent in the development of tourism resulting from the swamp of Paraiba. This is a qualitative descriptive and exploratory study, which makes use of the interpretive paradigm to perform an analysis of the environment where occurs the regionalization of tourism in Brejo of Paraíba and the social actors involved in this process in order to pursue development of the region through culture and tourism, with the collection spot in the six counties of the Project participants collected through interviews with managers, community, government agencies and tourist trade, and the use of the technique of direct observation. This time, with the data analysis it was possible to establish the production situation and its cultural and tourist development in the region of Brejo (PB), where culture has become a developmental tool within the tourism industry due to its innovation potential. It was possible to ratify the undisputed vocation of cultural tourism in the region in question, since other projects being developed with the use of cultural resources with a strong influence on the policies of regional tourism. Thus, the main result was that was seen is that the regional development has triggered a refunctionalisation / reappropriation of space just rebuilding a new territorial organization through the development of a regional autonomy of management, a capacity of collective ownership and the use of economic surplus, a spontaneous process of social inclusion as well as awareness and mobilization tourist (even if initial and shy), an appreciation of natural and cultural assets for all stakeholders and especially identification of the population with its region and its culture, as to achieve regional development is not enough to increase the economic, but above all the promotion of endogenous social factors such as changes in social and cultural values and the integration of social actors in this process. Finally, taking into account the definitions of sustainability, it is considered that cannot be said that the development model seen in the swamp of Paraiba is sustainable, but it is a model of regional development based on the unique characteristics that each municipality has and create a regional identity and have correponded expectations / desired results and therefore the viability of the region through the development of cultural tourism was proven

Otimização de parâmetros mecânicos e microestruturais dos moldes em areia de sílica ligados quimicamente pelo processo de cura a frio em fundição de aço

Surface defects on steel parts borne costs of smelting industries due to the need of rework. Sand molds are frequently used in foundry industries and largely responsible for providing surface defects. This study aims to optimize the levels of the molding process variables to minimize the occurrence of surface defects in steel castings in silica sand molds chemically linked by cold cure process. The methodology used the experimental design with split plot, being considered in the study the resin percentage factors in the mold formulation, addition of iron oxide, type of paint, the paint application method, amount of ink layers, use of hot air along the lines and waiting time of the mold before casting. They were analyzed as response variables erosion defects, sand inclusion, penetration, porosity and surface finish. Tensile strength tests were performed to evaluate the influence of factors on mechanical parameters and the microstructural parameters were carried out the analysis of X-ray diffraction, scanning electron microscopy (SEM) and thermal analysis (TG / DSC / dilatometry). The results elucidate that for the faulty erosion, the only significant factor with a 95% confidence level was the type of ink and the ink alumina-based superior results obtained. For the sand inclusion of defect, there were three significant factors, with best results obtained with alumina-based paint and spray applied using hot air in the mold before casting the metal. For the defect penetration, there were four significant factors, the best results being achieved with 0.8% of resin and addition of iron oxide in the molding formulation, the paint being applied by brush and standby time of 24 hours before leak. For the defect porosity with a 95% confidence level, no significant factors. For the defect surface finish, the best results were achieved with the 0.8% formulation of the resin in the mold and application of the paint brush. To obtain the levels of the factors that optimize all defects simultaneously, we performed a weighted average of the results of each type of fault, concluding that the best levels of the factors were: 0.8% resin and addition of iron oxide in the formulation of the template, application of two coats of paint applied with a brush or spray, using hot air in the mold before casting and 24 hours of waiting ready the mold before casting. These levels of the optimized factors were used in an experiment to confirm that ratified the results, helping to reduce rework and consequently reducing costs of cast steel parts.

Avaliação do retinol em parturientes com diabetes mellitus gestacional no pós parto imediato

Micronutrient deficiencies affect individuals mainly in developing countries, where vitamin A deficiency is a public health problem worldwide more worrying, especially in groups with increased physiological needs such as children and women of reproductive age. Vitamin A is supplied to the body through diet and has an important role in the visual process, cell differentiation, maintenance of epithelial tissue, reproductive and resistance to infection. The literature has demonstrated the relationship between vitamin A and diabetes, including gestational, leading to a risk to both mother and child. Gestational diabetes is any decrease in glucose tolerance of variable magnitude diagnosed each the first time during pregnancy, and may or may not persist after delivery. Insulin resistance during pregnancy is associated with placental hormones, as well as excess fat. Studies have shown that retinol transport protein produced in adipose tissue in high concentrations, this would be associated with resistance by interfering with insulin signaling. Therefore, this study aimed to evaluate the concentration of retinol in serum and colostrum from healthy and diabetic mothers in the immediate postpartum period. One hundred and nine parturient women were recruited, representing seventy-three healthy and thirty-six diabetic. Retinol was extracted and subsequently analyzed by High Performance Liquid Chromatography. Among the results highlights the mothers with gestational diabetes were older than mothers healthy, had more children and a higher prevalence of cases of cesarean section. Fetal macrosomia was present in 1.4% of healthy parturient women and in 22.2% of diabetic mothers. The maternal serum retinol showed an average of 39.7 ± 12.5 mg/dL for healthy parturients 35.12 ± 15 mg/dL for diabetic and showed no statistical difference. It was observed that in the group of diabetic had 17% vitamin A deficiency, whereas in the healthy group, only 4% of the women were deficentes. Colostrum, the concentration of retinol in healthy was 131.3 ± 56.2 mg/dL and 125.3 ± 41.9 mg/dL in diabetic did not differ statistically. This concentration of retinol found in colostrum provides approximately 656.5 mg/day for infants born to healthy mothers and 626.5 mg/day for infants of diabetic mothers, based on a daily consumption of 500 mL of breast milk and need Vitamin A 400 mg/day, thus reaching the requirement of the infant. The diabetic mothers showed significant risk factors and complications related to gestational diabetes. Although no 11 difference was found in serum retinol concentration and colostrum among women with and without gestational diabetes, the individual analysis shows that parturients women with diabetes are 4.9 times more likely to develop vitamin A deficiency than healthy parturients. However, the supply of vitamin A to the newborn was not committed in the presence of gestational diabetes

Avaliação da suplementação com vitamina E, na forma natural ou sintética, em mulheres no pós-parto imediato e sua concentração no colostro

The Vitamin E consists of eight chemically homologous forms, designated alpha, beta, gamma and delta tocopherols and tocotrienols. Biologically, the alpha-tocopherol (α-TOH) is the most important. Commercially, are found two types of α-TOH a natural (RRR-alpha-tocopherol) and another synthetic (all-rac-alpha-tocopherol). Both forms are absorbed in the intestine, the liver is a preference in favor of forms 2R, due to transfer protein α-TOH. It has higher affinity to these stereoisomers. Newborns are considered high risk for vitamin E deficiency, mainly premature, these have breast milk as a food source for maintenance of serum α-TOH. Clinical signs such as thrombocytosis, hemolytic anemia, retrolental fibroplasia, intraventricular hemorrhage, bronchopulmonary dysplasia and spinocerebellar degeneration can be found in case of a low intake of α-TOH. Thus, maternal supplementation on postpartum with α-TOH can be an efficient way to increase levels of vitamin E in breast milk and thus the consequently increase the supply of micronutrient for the newborn. However, most studies with vitamin E supplementation have been conducted in animals and little is known about the effect of maternal supplementation in humans, as well as on its efficiency to increase levels of α-TOH in human milk, depending on the shape natural or synthetic. The study included 109 women, divided into three groups: control without supplementation (GC) (n=36), supplemented with natural capsule (GNAT) (n=40) and the synthetic capsule (GSINT) (n=33). Blood samples were collected for determination of maternal nutritional status, and colostrums at initial contact and after 24 hours post-supplementation. Analyses were performed by High Performance Liquid Chromatography. Values of α-TOH in serum below 499.6mg/dL were considered deficient. We used the Kruskal-Wallis test and Tukey test to confirm the increase of alpha-tocopherol in milk and efficiency of administered capsules. Daily consumption of α-TOH was based on daily intake of 500 mL of colostrum by the newborn and compared with the nutritional requirement for children from 0 to 6 months of age, 4 mg / day. The mothers had mean concentration of serum α-TOH in 1016 ± 52, 1236 ± 51 and 1083 ± 61 mg / dL, in CG, GNAT and GSINT respectively. There were no women with deficiiency. The GC did not change the concentrations of α-TOH in colostrum. While women supplemented with natural and synthetic forms increased concentrations of α-TOH colostrum in 57.6% and 39%, respectively. By comparing supplemented groups, it was observed a significant difference (p=0.04), the natural capsule more efficient than the synthetic, approximately 49.6%. Individually, 21.1% of the women provided below 4mg/day of α-TOH, after supplementation for this index declined4.1%. Thus, maternal supplementation postpartum raised the levels of alpha-tocopherol in colostrum, and increased efficiency was observed with the natural form

Processo biotecnológico voltado a produção de estoques poliploides do camarão-branco litopenaeus vannamei (decapoda, penaeidae)

without practical results so far. Protocols used in biotechnological cultured aquatic organisms aimed at increasing growth rates and disease resistance, have been studied and perfected. Among the available techniques, the application of chromosomal manipulation, although still nascent, is presented as a tool aimed at mitigating ecological and economical issues in shrimp farming. The polyploidization artificial method already employed in fish and shellfish, has been widely researched for use in farmed shrimp. Some limitations of this method of expansion in shrimp refer to a better knowledge of cytogenetic aspects, the level of sexual dimorphism and performance in growing conditions. To contribute on some of these issues, the present study aimed to characterize cytogenetic species Litopenaeus vannamei (Decapoda) and Artemia franciscana (Anostraca), analyze the effectiveness of methods for detection of ploidy, through the use of flow cytometry in processes of induction polyploidy cold thermal shock at different stages of development of newly fertilized eggs. Additionally, aimed also the qualitative and quantitative comparison of larval development between diploid and polyploid organisms, besides the identification of sexual dimorphism in L. vannamei, through geometric morphometrics. The results provide information relevant to the improvement and widespread use of biotechnological methods applied toward national productivity in shrimp farming

Estudo da sinterização do aço inox 316L reforçado com 3% Carbeto de Tântalo - TaC

The present work shows a contribution to the studies of development and solid sinterization of a metallic matrix composite MMC that has as starter materials 316L stainless steel atomized with water, and two different Tantalum Carbide TaC powders, with averages crystallite sizes of 13.78 nm and 40.66 nm. Aiming the metallic matrix s density and hardness increase was added different nanometric sizes of TaC by dispersion. The 316L stainless steel is an alloy largely used because it s high resistance to corrosion property. Although, its application is limited by the low wear resistance, consequence of its low hardness. Besides this, it shows low sinterability and it cannot be hardened by thermal treatments traditional methods because of the austenitic structure, face centered cubic, stabilized mainly in nickel presence. Steel samples added with TaC 3% wt (each sample with different type of carbide), following a mechanical milling route using conventional mill for 24 hours. Each one of the resulted samples, as well as the pure steel sample, were compacted at 700 MPa, room temperature, without any addictive, uniaxial tension, using a 5 mm diameter cylindrical mold, and quantity calculated to obtain compacted final average height of 5 mm. Subsequently, were sintered in vacuum atmosphere, temperature of 1290ºC, heating rate of 20ºC/min, using different soaking times of 30 and 60 min and cooled at room temperature. The sintered samples were submitted to density and micro-hardness analysis. The TaC reforced samples showed higher density values and an expressive hardness increase. The complementary analysis in optical microscope, scanning electronic microscope and X ray diffractometer, showed that the TaC, processed form, contributed with the hardness increase, by densification, itself hardness and grains growth control at the metallic matrix, segregating itself to the grain boarders

Avaliação do desempenho do aço D6 tratado termicamente e netretado em plasma com gaiola catódica visando aplicação industrial

In this research there was an evaluation of the best conditions of nitriding in plasma within a cathodic cage at an atmosphere of 80% N2-20%H2 in samples of tool manganese steel AISI D6, cold working, treated thermally in the following conditions: tension relief, treated thermally to temperature of maximum heat, temperate heat and temperate and temperate heat. A pressure of 2.5mbar and temperatures of 400 and 300ºC com treatment time of two and three hours were used to evaluate its performance as cutting tool (punch) of bicycle backs. Hardness, micro-structural aspects (layer thickness, interface, grain size etc), and crystal phases on the surface were appraised. When treated to tension relief, thermally treated to maximum heat temperature, temperature and temperate heat, the samples presented hardness levels of 243HV, 231HV, 832HV, and 653HV, respectively. The best nitrification conditions were: four hours and 300ºC for heat samples. A superficial hardness of 1000HV and a 108µm thickness for the nitrided layer were found in these samples

Sinterização de aço inoxidável reforçado com partículas nanométricas dispersas de carbeto de nióbio - NbC

Metal powder sintering appears to be promising option to achieve new physical and mechanical properties combining raw material with new processing improvements. It interest over many years and continue to gain wide industrial application. Stainless steel is a widely accepted material because high corrosion resistance. However stainless steels have poor sinterability and poor wear resistance due to their low hardness. Metal matrix composite (MMC) combining soft metallic matrix reinforced with carbides or oxides has attracted considerable attention for researchers to improve density and hardness in the bulk material. This thesis focuses on processing 316L stainless steel by addition of 3% wt niobium carbide to control grain growth and improve densification and hardness. The starting powder were water atomized stainless steel manufactured for Höganäs (D 50 = 95.0 μm) and NbC produced in the UFRN and supplied by Aesar Alpha Johnson Matthey Company with medium crystallite size 16.39 nm and 80.35 nm respectively. Samples with addition up to 3% of each NbC were mixed and mechanically milled by 3 routes. The route1 (R1) milled in planetary by 2 hours. The routes 2 (R2) and 3 (R3) milled in a conventional mill by 24 and 48 hours. Each milled samples and pure sample were cold compacted uniaxially in a cylindrical steel die (Ø 5 .0 mm) at 700 MPa, carried out in a vacuum furnace, heated at 1290°C, heating rate 20°C stand by 30 and 60 minutes. The samples containing NbC present higher densities and hardness than those without reinforcement. The results show that nanosized NbC particles precipitate on grain boundary. Thus, promote densification eliminating pores, control grain growth and increase the hardness values

Efeito da moagem de alta energia na microestrutura e nas propriedades magnéticas do compósito wc-10%p.Co

This work a studied the high energy milling effect in microstructure and magnetic properties of the WC-10wt.%Co composite. The composite powders were prepared by mechanical mixed and milled at 2 hours, 100 hours, 200 hours and 300 hours in planetary milling. After this process the composite were compacted in stainless steel die with cylindrical county of 10 mm of diameter, at pressure 200 Mpa and sintered in a resistive furnace in argon atmosphere at 1400 oC for 5 min. The sintered composite were cutted, inlaid, sandpapered, and polished. The microestrutural parameters of the composite was analyzed by X-ray diffraction, scanning electronic microscopy, optical microscopy, hardness, magnetic propriety and Rietveld method analyze. The results shows, with milling time increase the particle size decrease, it possibility minor temperature of sintering. The increase of milling time caused allotropic transformation in cobalt phase and cold welding between particles. The cold welding caused the formation of the particle composite. The X-ray diffraction pattern of composite powders shows the WC peaks intensity decrease with the milling time increase. The X-ray diffraction pattern of the composite sintered samples shows the other phases. The magnetic measurements detected a significant increase in the coercitive field and a decrease in the saturation magnetization with milling time increase. The increase coercitive field it was also verified with decrease grain size with milling time increase. For the composite powders the increase coercitive field it was verified with particle size reduction and saturation magnetization variation is relate with the variation of free cobalt. The Rietveld method analyze shows at milling time increase the mean crystalline size of WC, and Co-cfc phases in composite sintered sample are higher than in composite powders. The mean crystallite size of Co-hc phase in composite powders is higher than in composite sintered sample. The mean lattice strains of WC, Co-hc and Co-cfc phases in composite powders are higher than in composite sintered samples. The cells parameters of the composite powder decrease at milling time increase this effect came from the particle size reduction at milling time increase. In sintered composite the cells parameters is constant with milling time increase

Desenvolvimento e caracterização de um compósito matriz metálica (CMM): aço EUROFER97 reforçado com Carbeto de Tântalo - TaC

Steel is an alloy EUROFER promising for use in nuclear reactors, or in applications where the material is subjected to temperatures up to 550 ° C due to their lower creep resistance under. One way to increase this property, so that the steel work at higher temperatures it is necessary to prevent sliding of its grain boundaries. Factors that influence this slip contours are the morphology of the grains, the angle and speed of the grain boundaries. This speed can be decreased in the presence of a dispersed phase in the material, provided it is fine and homogeneously distributed. In this context, this paper presents the development of a new material metal matrix composite (MMC) which has as starting materials as stainless steel EUROFER 97, and two different kinds of tantalum carbide - TaC, one with average crystallite sizes 13.78 nm synthesized in UFRN and another with 40.66 nm supplied by Aldrich. In order to improve the mechanical properties of metal matrix was added by powder metallurgy, nano-sized particles of the two types of TaC. This paper discusses the effect of dispersion of carbides in the microstructure of sintered parts. Pure steel powders with the addition of 3% TaC UFRN and 3% TaC commercial respectively, were ground in grinding times following: a) 5 hours in the planetary mill for all post b) 8 hours of grinding in the mill Planetary only for steel TaC powders of commercial and c) 24 hours in the conventional ball mill mixing the pure steel milled for 5 hours in the planetary mill with 3% TaC commercial. Each of the resulting particulate samples were cold compacted under a uniaxial pressure of 600MPa, on a cylindrical matrix of 5 mm diameter. Subsequently, the compressed were sintered in a vacuum furnace at temperatures of 1150 to 1250 ° C with an increment of 20 ° C and 10 ° C per minute and maintained at these isotherms for 30, 60 and 120 minutes and cooled to room temperature. The distribution, size and dispersion of steel and composite particles were determined by x-ray diffraction, scanning electron microscopy followed by chemical analysis (EDS). The structures of the sintered bodies were observed by optical microscopy and scanning electron accompanied by EDS beyond the x-ray diffraction. Initial studies sintering the obtained steel EUROFER 97 a positive reply in relation to improvement of the mechanical properties independent of the processing, because it is obtained with sintered microhardness values close to and even greater than 100% of the value obtained for the HV 333.2 pure steel as received in the form of a bar

Compósitos de matriz metálica à base níquel com adição de TaC e NbC produzidos via metalurgia do pó

Carbide reinforced metallic alloys potentially improve some important mechanical properties required for the overall use of important engineering materials such as steel and nickel. Nevertheless, improved performance is achieved not only by composition enhancement but also by adequate processing techniques, such as novel sintering methods in the case of powder metallurgy. The method minimizes energy losses in addition to providing uniform heating during sintering. Thus, the general objective of this study was to evaluate the density, hardness, flexural strength, dilatometric behavior and to analyze the microstructure of metal matrix composites based nickel with addition of carbides of tantalum and / or niobium when sintered in a conventional furnace and Plasma assisted debinding and sintering (PADS). Initially, were defineds best parameters of granulation, screening and mixing procedure. After, mixtures of carbonyl Ni and 5%, 10% and 15 wt.% NbC and TaC were prepared in a Y-type mixer under wet conditions during 60 minutes. The mixtures were then dried and granulated using 1.5 wt. % paraffin diluted in hexane. Granulates were cold pressed under 600 MPa. Paraffin was then removed from the pressed pellets during a pre-sintering process carried out in a tubular furnace at 500 °C during 30 min. The heating rate was 3 ºC/min. The pellets were then sintered using either a plasma assisted reactor or a conventional resistive tubular furnace. For both methods, the heating rate was set to 8 ºC/min up to 1150 °C. The holding time was 60 minutes. The microstructure of the sintered samples was evaluated by SEM. Brinell hardness tests were also carried out. The results revealed that higher density and higher hardness values were observed in the plasma-assisted sintered samples. Hardness increased with the concentration of carbides in the Ni-matrix. The flexural strength also increased by adding the carbides. The decline was larger for the sample with addition of 5% 5% TaC and NbC. In general, compositions containing added carbide 10% showed less porous and more uniform distribution of carbides in the nickel matrix microstructural appearance. Thus, both added carbide and plasma sintering improved density, hardness, flexural strength and microstructural appearance of the composites

Análise teórico-experimental do coeficiente de perfomance (COP) de um sistema de refrigeração por jato-compressão

The use of waste heat of energy conversion equipment to produce a cooling effect, consists currently in a very interesting way of efficiency improvement of energy systems. The present research has as intention the theoretical and experimental study of a new intermittent refrigeration system ejector cycle characteristics, with use of waste heat. Initially, was doing a bibliographical survey about the vapor ejector refrigeration system technology. In the following stage was doing a simulation of the corresponding thermodynamic cycle, with preliminarily intention to evaluate the performance of the system for different refrigerants fluids. On the basis of the results of the simulation were selected the refrigerant fluid and developed an experimental group of benches of the refrigeration system considered, where pressure and temperature sensory had been inserted in strategical points of the refrigeration archetype and connected to a computerized data acquisition system for measure the refrigerant fluid properties in the thermodynamic cycle. The test results obtained show good agreement with the literature

Variação de temperatura e umidade e suas influências nas características físicas e mecânicas dos fios de algodão

Cotton is a hydrofilic textile fiber and, for this reason, it changes its properties according to the environment changes. Moisture and Temperature are the two most important factors that lead a cotton Spinning sector and influence its quality. Those two properties can change the entire Spinning process. Understanding this, moisture and temperature must be kept under control when used during the Spinning process, once the environment is hot and dry, the cotton yarns absorb moisture and lose the minimal consistency. According to this information, this paper was developed testing four types of cotton yarns, one kind of cotton from Brazil and the others from Egypt. The yarns were exposed to different temperatures and moisture in five different tests and in each test, six samples that were examined through physical and mechanical tests: resistance, strength, tenacity, yarn´s hairness, yarn´s evenness and yarn´s twisting. All the analysis were accomplished at Laboratório de Mecânica dos Fluídos and at COATS Corrente S.A., where, it was possible to use the equipments whose were fundamental to develop this paper, such as the STATIMAT ME that measures strength, tenacity, Zweigler G566, that measure hairiness in the yarn, a skein machine and a twisting machine. The analysis revealed alterations in the yarn´s characteristics in a direct way, for example, as moisture and temperature were increased, the yarn´s strength, tenacity and hairness were increased as well. Having the results of all analysis, it is possible to say that a relatively low temperature and a high humidity, cotton yarns have the best performance