Avaliação de metodologia de preparo de amostra de petróleo por digestão ácida auxiliada por microondas para determinação de metais por ICP-OES

This project describes a methodology optimization that would allow for a more efficient microwave assisted digestion process for petroleum samples. With the possible chance to vary various factors at once to see if any one factor was significant enough in the answers, experimental planning was used. Microwave assisted digestion allows, through the application of potency, an increasing number of collisions between the HNO3 and H2O2 molecules, favoring sample opening for complex matrixes. For this, a 24 factorial experimental planning was used, varying potency, time and the volumes for HNO3 65% and H2O2 30%. To achieve the desired answers, several elements were monitored (C, Cu, Cr, Fe, Ni, Zn and V) through Inductively coupled plasma atomic emission spectroscopy (ICP-OES). With this initial study it was noticed that the HNO3 was not a significant factor for any of the statistical studies for any of the analytes and the other 3 factors and their interactions showed statistical significance. A Box Behnken experimental planning was used taking in consideration 3 factors: H2O2 volume, time (min) and Potency (W), Nitric Acid kept at 4mL for a mass of 0,1g of petroleum. The results were extremely satisfying showing higher efficiency in the digestion process and taking in a responsibility between the answers for each analyte and the carbon monitoring was achieved in the following conditions: 7mL of H2O2, 700 Watts of potency and a reaction time of 7 minutes with 4mL de HNO3 for a mass of 0,1g of petroleum. The optimized digestion process was applied to four different petroleum samples and the analytes determined by ICP-OES

Membranas de quitosana micro e macroporosas : preparo, caracterização e estudos de permeabilidade

Two methodologies were proposed to obtain micro and macroporous chitosan membranes, using two different porogenic agents. The methodologies proved to be effective in control the porosity as well as the pore size. Thus, microporous membranes were obtained through the physical blend of chitosan and polyethylene oxide (PEO) on an 80:20 (m/m) ratio, respectively, followed by the partial PEO solubilization in water at 80 ◦C. Macroporous chitosan membranes with asymmetric morphology were obtained using SiO2 as the porogenic agent. In this case, chiotsan-silica ratios used were 1:1, 1:3 and 1:5 (m/m). Membranes characterization were carried out by SEM (scanning electronic microscopy), X-ray diffraction, Fourier Transform Infrared Spectroscopy (FTIR), Thermal analysis (TG, DTG , DSC and DMTA). Permeability studies were performed using two model drugs: sodium sulfamerazine and sulfametoxipyridazine. By transmission FTIR it was possible to confirm the complete removal of SiO2. The SEM images confirmed the porous formation for both micro and macroporous membranes and also determined their respective sizes. By thermal analysis it was possible to show differences related with water sorption capacity as well as thermal stability for both membranes. DTG and DSC allowed evidencing the PEO presence on microporous membranes. The absorbance x time curves obtained on permeability tests for micro and macroporous membranes showed a linear behavior for both drugs in all range of concentration used. It was also observed, through P versus C curves, an increase in permeability of macroporous membranes according to the increase in porosity and also a decrease on P with increase in drug concentration. The influences of the drug molecular structure, as well as test temperatures were also evaluated

Preparo e caracterização de membranas de quitosana modificadas com poli (ácido acrílico)

The aim of this study was to generate an asymmetric biocompactible and biodegradable chitosan membrane modified by the contact with a poly(acrylic acid) solution at one of its sides at room temperature and 60◦C. The pure chitosan membrane, as well as the ones treated with poly(acrylic acid) were characterized by infrared spectroscopy (FTIRATR) at angles of 39◦, 45◦ and 60◦ , swelling capacity in water, thermal analysis (TG/DTG), scanning electronic microscopy (SEM) and permeation experiments using metronidazole at 0,1% and 0,2% as a model drug. The results confirmed the presence of ionic interaction between chitosan and poly(acrylic acid) by means of a polyelectrolyte complex (PEC) formation. They also showed that such interactions were more effective at 60◦C since this temperature is above the chitosan glass transition temperature wich makes the diffusion of poly(acrylic acid) easier, and that the two treated membranes were asymmetrics, more thermically stable and less permeable in relation to metronidazole than the pure chitosan membrane

"Cantata para louvor e glória", de Cleide Dorta Benjamim: preparo para a execução

This study aims to document the preparation process for the implementation of "Cantata To Praise and Glory"(Cantata Para Louvor e Glória), composed in 1985 by composer Cleide Dorta Benjamin (1936 - ), in order to anticipate and address the possible difficulties faced by future conductors, singers and instrumentalists. Issues that relate to the chosen text as well as its structure and importance in the compositional process, are initially addressed through a brief presentation of the work. Consequently, by addressing every detail of the work, solutions to vocal and instrumental execution difficulties, as well as with the conducting gesture, are analyzed, identified and proposed. The work also presents a report that describes all the practical processes of preparation of the Cantata: reissue of the score; selection and profile of singers and instrumentalists; rehearsals; changes and adjustments to the score; and a brief interview with four singers and two musicians who participated in the process. The interaction with the composer throughout a significant part of the work, brings a notable increase of possible clarifications and idea development, enabling a coherent performance of the work.

Avaliação de metodologia de preparo de amostra de petróleo por digestão ácida auxiliada por microondas para determinação de metais por ICP-OES

This project describes a methodology optimization that would allow for a more efficient microwave assisted digestion process for petroleum samples. With the possible chance to vary various factors at once to see if any one factor was significant enough in the answers, experimental planning was used. Microwave assisted digestion allows, through the application of potency, an increasing number of collisions between the HNO3 and H2O2 molecules, favoring sample opening for complex matrixes. For this, a 24 factorial experimental planning was used, varying potency, time and the volumes for HNO3 65% and H2O2 30%. To achieve the desired answers, several elements were monitored (C, Cu, Cr, Fe, Ni, Zn and V) through Inductively coupled plasma atomic emission spectroscopy (ICP-OES). With this initial study it was noticed that the HNO3 was not a significant factor for any of the statistical studies for any of the analytes and the other 3 factors and their interactions showed statistical significance. A Box Behnken experimental planning was used taking in consideration 3 factors: H2O2 volume, time (min) and Potency (W), Nitric Acid kept at 4mL for a mass of 0,1g of petroleum. The results were extremely satisfying showing higher efficiency in the digestion process and taking in a responsibility between the answers for each analyte and the carbon monitoring was achieved in the following conditions: 7mL of H2O2, 700 Watts of potency and a reaction time of 7 minutes with 4mL de HNO3 for a mass of 0,1g of petroleum. The optimized digestion process was applied to four different petroleum samples and the analytes determined by ICP-OES

Os impactos tecnológicos da implantação da nota fiscal eletrônica: um estudo de casos múltiplos

Increasingly, the Information Technology is used in the society, including the private, public and third sector organizational context. Technological tools are created in order to speed, automate, control and monitor processes. These technologies generate impacts on areas that permeate their use and the objective of this study is to investigate the implementation process of the Eletronic Invoice and the impacts arising from this technological tool in companies. For that, case studies have been conducted in three companies that emit and receive Eletronic Invoice, in a Information System consultancy, that provides softwares of Eletronic Invoice, and in a State Tax Department. Data collection was performed with organizations representatives through electronic questionnaires. The study concludes that it is expected, by the investigated organizations, that the tool reaches the benefits offered by the Tax Administration. However, these benefits have not been identified yet and neither have the use of methodologies in order to identify them. Moreover, the main impact found was the need for better training and participant´s technical qualification, followed by reducing printing costs and paper purchase

A experiência no Tai Chi: possibilidades para pensar o corpo sem órgãos e a preparação do ator

Although research in the field of performing arts has substantially advanced over the last century, the actor, in general, still needs a repertoire of specific references to guide or support his practice. But how the actor must work the material foundation of his art that is his own body? Starting from a prerogative of a idiosyncrasy that is part of theater, this study intend, from the description and reflection about one physical experience with the Tai Chi, to weave relations between this experience and the possible developments of acting preparation. This research is also aimed to highlight the elements of connection between the principles that rules Tai Chi and the body without organs, idealized by Artaud, with the perspective of pointing possible contributions for actors work. The work presented here refers to a qualitative study that considers the body experience in practice of Tai Chi as a reference to dialogue and reflect about the acting preparation. The process of acting preparation presupposes a constant redoing of the body by certain practices. My experience with Tai Chi within this research allowed me verify that the work from established body techniques could be a way of technical preparation for the actor. As the body conscience expands, Tai Chi promotes a greater freedom of creation and expression, giving the actor the possibility of experience the body without organs, the artistic equivalent of the daily body, present, conscious, the organic foundation of emotions, in wich it is possible the materiality of ideas

Síntese e impregnação de peneiras moleculares Fe MCM-41 derivada de sílica da casca do arroz

The mesoporous molecular sieves of the MCM-41 and FeMCM-41 type are considered promissory as support for metals used as catalysts in oil-based materials refine processes and as adsorbents for environmental protection proposes. In this work MCM-41 and FeMCM41 were synthesized using rice husk ash - RHA as alternative to the conventional silica source. Hydrothermal synthesis was the method chosen to prepare the materials. Pre-defined synthesis parameters were 100°C for 168 hours, later the precursor was calcinated at 550°C for 2 hours under nitrogen and air flow. The sieves containing different proportions of iron were produced by two routes: introduction of iron salt direct synthesis; and a modification post synthesis consisting in iron salt 1 % and 5% impregnation in the material followed by thermal decomposition. The molecular sieves were characterized by X ray diffraction XRD, Fourier transform infrared spectroscopy FT-IR, X ray fluorescence spectroscopy XFR, scanning electronic microscopy SEM, specific surface area using the BET method, Termogravimetry TG. The kinetic model of Flynn Wall was used with the aim of determining the apparent activation energy of the surfactant remove (CTMABr) in the MCM- 41 porous. The analysis made possible the morphology characterization, identifying the presence of hexagonal structure typical for mesoporous materials, as well as observation of the MCM41 and iron of characteristic bands.

Desenvolvimento de membranas porosas de alumina para fins de tratamento de efluente industrial têxtil

Textile production has been considered as an activity of high environmental impact due to the generation of large volumes of waste water with high load of organic compounds and strongly colored effluents, toxic and difficult biodegradability. This thesis deals with obtaining porous alumina ceramic membranes for filtration of textile effluent in the removal of contaminants, mainly color and turbidity. Two types of alumina with different particle sizes as a basis for the preparation of formulation for mass production of ceramic samples and membranes. The technological properties of the samples were evaluated after using sintering conditions: 1,350ºC-2H, 1,450ºC-30M, 1,450ºC-2H, 1,475ºC-30M and 1,475ºC-2H. The sintered samples were characterized by XRD, XRF, AG, TG, DSC, DL, AA, MEA, RL, MRF-3P, SEM and Intrusion Porosimetry by Mercury. After the characterization, a standard membrane was selected with their respective sintering condition for the filterability tests. The effluent was provided by a local Textile Industry and characterized at the entry and exit of the treatment plant. A statistical analysis was used to study the effluent using the following parameters: pH, temperature, EC, SS, SD, oil and grease, turbidity, COD, DO, total phosphorus, chlorides, phenols, metals and fecal coliform. The filtered effluent was evaluated by using the same parameters. These results demonstrate that the feasibility of the use of porous alumina ceramic membranes for removing contaminants from textile effluent with improved average pore size of 0.4 micrometre (distribution range varying from 0,025 to 2.0 micrometre), with total porosity of 29.66%, and average percentages of color removal efficiency of 89.02%, 92.49% of SS, turbidity of 94.55%, metals 2.70% (manganese) to 71.52% (iron) according to each metal and COD removal of 72.80%

Estudo da viabilidade do processo de reciclagem do material descartado do sistema Zirkonzanh® de produção de próteses dentárias

At present, the material of choice for performing aesthetic dental prosthetic work is in the ceramic. Among them, the ceramic base of stabilized zirconia with 3% yttria (3Y - TZP) stand out for having excellent physical and mechanical properties. During the machining of blocks of zirconia in the laboratory to prepare the various types of prostheses, much of the material is given off in the form of powder, which is subsequently discarded. The waste of this material results in financial loss, reflecting higher final cost treatment for patients, as well as damage to the environment, thanks to the processes involved in the manufacture and disposal of the ceramic. This research, pioneered the recycling of zirconium oxide powder obtained during milling of dental crowns and bridges, we highlight the social and environmental aspects and aims to establish a protocol for the reuse of waste (powder of zirconia Zirkonzahn® system) discarded to obtain a new block of compacted zirconia to maintain the same mechanical and microstructural properties of commercial high-cost imported material. To compare with the commercial material, samples were uniaxially (20 MPa) and isostatically (100 MPa), and its mechanical and microstructural characterization was performed through tests of density, porosity, dilatometry, X-ray diffraction (XRD), hardness, fracture toughness, resistance to fracture electron microscopy (SEM) and analysis of grain size. The results observed in the samples were isostatically pressed similiares those obtained with samples from the commercial material demonstrating the viability of the process

Avaliação do desenvolvimento neuropsicomotor em crianças na rede básica de saúde utilizando o teste de Denver II: identificação de fatores de risco materno

Alterations in the neuropsychomotor development of children are not rare and can manifest themselves with varying intensity at different stages of their development. In this context, maternal risk factors may contribute to the appearance of these alterations. A number of studies have reported that neuropsychomotor development diagnosis is not an easy task, especially in the basic public health network. Diagnosis requires effective, low-cost, and easy - to-apply procedures. The Denver Developmental Screening Test, first published in 1967, is currently used in several countries. It has been revised and renamed as the Denver II Test and meets the aforementioned criteria. Accordingly, the aim of this study was to apply the Denver II Test in order to verify the prevalence of suspected neuropsychomotor development delay in children between the ages of 0 and 12 months and correlate it with the following maternal risk factors: family income, schooling, age at pregnancy, drug use during pregnancy, gestational age, gestational problems, type of delivery and the desire to have children. For data collection, performed during the first 6 months of 2004, a clinical assessment was made of 398 children selected by pediatricians and the nursing team of each public health unit. Later, the parents or guardians were asked to complete a structured questionnaire to determine possible risk indicators of neuropsychomotor development delay. Finally the Denver II Developmental Screening Test (DDST) was applied. The data were analyzed together, using Statistical Package for Social Science (SPSS) software, version 6.1. The confidence interval was set at 95%. The Denver II Test yielded normal and questionable results. This suggests compromised neuropsychomotor development in the children examined and deserves further investigation. The correlation of the results with preestablished maternal risk variables (family income, mother s schooling, age at pregnancy, drug use during the pregnancy and gestational age) was strongly significant. The other maternal risk variables (gestational problems, type of delivery and desire to have children) were not significant. Using an adjusted logistic regression model, we obtained the estimate of the greater likelihood of a child having suspected neuropsychomotor development delay: a mother with _75 4 years of schooling, chronological age less than 20 years and a drug user during pregnancy. This study produced two manuscripts, one published in Acta Cirúrgica Brasileira , in which an analysis was performed of children with suspected neuropsychomotor development delay in the city of Natal, Brazil. The other paper (to be published) analyzed the magnitude of the independent variable maternal schooling associated to neuropsychomotor development delay, every 3 months during the first twelve months of life of the children selected.. The results of the present study reinforce the multifactorial characteristic of development and the cumulative effect of maternal risk factors, and show the need for a regional policy that promotes low-cost programs for the community, involving children at risk of neuropsychomotor development delay. Moreover, they suggest the need for better qualified health professionals in terms of monitoring child development. This was an inter- and multidisciplinary study with the integrated participation of doctors, nurses, nursing assistants and professionals from other areas, such as statisticians and information technology professionals, who met all the requirements of the Postgraduate Program in Health Sciences of the Federal University of Rio Grande do Norte

Avaliação das condições higiênico-sanitárias da produção de refeições à base de carne da alimentação escolar no município de Natal-RN

The National School Nutrition Program is the oldest program in the country directed at food and nutrition safety. Its aims are to offer nutritional food as a supplement to students of public and philanthropic schools. Studying school nutrition transcends the investigation as a purely social program, given that it reaches the fields of public health, nutrition and food, using a wide variety of approaches. Thus, it is characterized by a multidisciplinary study, where the disciplines work side by side in distinct aspects of a single problem. Aim: This study aims to assess hygiene practices during the preparation of meat-based meals in public schools in the city of Natal, Brazil. Methods: A list was applied at 27 schools to identify the procedures of good food preparation practices. In addition, cooking and meal distribution temperature were measured and a microbiological analysis of the final preparation and of the water used in preparing it was performed. For microbiological analyses of the food, we analyzed coliforms at 45°C, coliforms at 35°C and Enterococcus, and for the water, we analyzed thermotolerant coliforms and total coliforms, using the methods recommended by APHA, 1995. Results: Most of the schools did not meet the required standards in all the variables related to good food preparation practices, except for the time spent preparing the meat, in which 89% were within the norm. Cooking temperature of the meals was within the standard; however, the temperature at distribution and the time spent dispensing the meals were inadequate. Of the 27 schools, 22 (81.5%) showed the presence of coliforms at 35° C in at least one meal sample and 18 (66.7%) had values above the recommended limit for coliforms at 45°C. The presence of E. coli was identified in 6.1% of the samples analyzed. The presence of Enterococcus was not found at any of the schools. With respect to the water, the North district of the city was the only one that did not meet the standards for the two indicators evaluated. The contamination found was not associated with the hygiene or food storage problems observed. Conclusions: The results show that the hygiene-sanitary conditions of meat-based public school meals were unsatisfactory, demonstrating the need for improvements in the production process to preserve the health of the student population. Multidisciplinarity: Researchers from the areas of food microbiology, nutrition, public health and statistics took part in this study, a decisive factor for characterizing the research as multidisciplinary

Efeitos de um extrato aquoso de porangaba (Cordia salicifolia) na marcação de constituintes sanguíneos com tecnécio-99m e na morfologia de hemácias

Effects of a Cordia salicifolia (porangaba) extract on the labeling of blood cells (BCs) with technetium-99m ((99m)Tc) and on the morphology of red BCs were evaluated. Labeling of cellular and molecular structures with (99m)Tc depends on a reducing agent. Some physical characteristics, as visible absorbance spectrum, electric conductivity, and refractive index of this porangaba extract, were also determined. Blood samples from Wistar rats were incubated with porangaba extract or with 0.9% NaCl (control). Labeling of blood constituents with (99m)Tc was performed. Plasma (P) and BCs, both soluble (SF-P and SF-BC) and insoluble (IF-P and IF-BC) fractions, were separated. The radioactivity in each fraction was counted, and the percentage of radioactivity incorporated (%ATI) was calculated. Blood smears were prepared, fixed, and stained, and the morphology of the red BCs was evaluated. Data showed an absorbance peak at 480 nm and electric conductibility and refractive index concentration-dependent. Porangaba extract decreased significantly (P < .05) the BC, IF-P, and IF-BC %ATI, and no modifications were verified on the shape of red BCs. Analysis of the results reveals that some physical parameters could be useful to aid in characterizing the extract studied. Moreover, it is possible that chemical compounds of this extract could have chelating/redox actions or be capable of binding to plasma and/or cellular proteins

Um modelo analítico da qualidade da dieta de adolescentes estudantes da rede publica de ensino de Natal, Brasil

Conselho Nacional de Desenvolvimento Científico e Tecnológico

Determinação de parâmetros de qualidade para formas farmacêuticas homeopáticas

All medicine, whether allopathic or homeopathic, must go through strict quality control, which must ratify their characteristics throughout the period of validity. During the time of preparation and storage, solutions of the drugs are in permanent contact with packaging materials that can release undesirable substances to the solution. Several factors may influence the release of packing materials, and factorial design (FD) is a useful tool for analyzing the phenomenon. The aim of this study was the determination of quality parameters for Homeopathic solid (globules) and liquid (drops) dosage forms. It was carried out analysis in homeopathic globules for weight variation, mechanical strength, and moisture content uniformity. For liquid preparations, standard solutions were prepared from natural rubber bulbs, which were subjected to exhaustive extraction with two ethanol solutions (30 and 70%) in the ultrasonic bath for 20 minutes at 25°C and 50°C in three successive cycles. Studies of transfer have been made within five days, by spectrophotometric analysis in the UV region at 312 nm with λmáx and 323 nm for samples in 70% ethanol and 30% respectively. PH values were analyzed. We also conducted two FD studies, where the first, the three-level variables were solvent (chloroform, ethanol and nhexane), sample mass (30, 60 and 90mg), particle size (large disk, small disk and powder sample). In the second study, the solvent level variables were different ethanolic degrees (EtOH 30%, 70% and pure). The percentage of lending in the solutions was 5.5%, 12.4%, 24.2% and 41% of the total estimated in the reference solution. The values of rate constants of transfer were determined in the order of 0.0134 days-1 and 0.0232 days-1 in absorbance values, the solutions in ethanol at 30% and 70% respectively. These results suggest that the speed of transfer of materials from rubber is affected both by the nature of the vehicle as by the temperature