Síntese e caracterização de óxidos de zinco e de magnésio suportados em A1SBA-15 para produção de biodiesel

To overcome the challenge of meeting growing energy demand in a sustainable way, biodiesel has shown very promising as alternative energy can replace fossil fuels, even partially. Industrially, the biodiesel is produced by homogeneous transesterification reaction of vegetable oils in the presence of basic species used as catalysts. However, this process is the need for purification of the esters obtained and the removal of glycerin formed after the reaction. This context, the alternative catalysts have that can improve the process of biodiesel production, aiming to reduce costs and facilitate its production. In this study, the AlSBA-15 support with Si / Al ratio = 50 was synthesized, as like as the heterogeneous catalysts of zinc oxide and magnesium supported on mesoporous AlSBA-15 silica, in the concentrations of 5, 10, 15 and 30 %, relative to the support. The textural properties and structural characterization of catalysts and supports were determined by techniques: X-ray diffraction (XRD), scanning electron microscopy (SEM), transmission electron microscopy (TEM) coupled to the chemical analyzer, adsorption / desorption of N2, thermal analysis (TG / DTG), absorption spectroscopy in the infrared (FTIR) and X-ray photoelectron spectroscopy (XPS). Characterization results indicated that the support AlSBA-15 retained the hexagonal ordered after the incorporation of zinc oxide and magnesium oxide in the holder. For heterogeneous catalysts, ZnO-AlSBA-15, that was observed the presence of zinc oxide nanoparticles dispersed in the surface and interior channels of the mesoporous and microporous support. The catalytic activity was evaluated by the transesterification reaction of sunflower oil via methylic route, and some reaction parameters were optimized with the most active catalyst in biodiesel production by sunflower oil. For the series of heterogeneous catalysts, the sample with 30 % ZnO supported on AlSBA-15 showed a better conversion of triglyceride to methyl esters, about 95.41 % of reaction conditions: temperature 175 °C, with molar ratio of 42:1, stirring at 200 rpm and under a pressure of 14 bar for 6 h. The catalyst MgO-AlSBA-15 showed no catalytic activity in the studied reactions

Conversão catalítica de clorometano em hidrocarbonetos

Amorphous silica-alumina and modified by incipient impregnation of iron, nickel, zinc and chromium were synthetized in oxide and metal state and evaluated as catalysts for the chloromethane conversion reaction. With known techniques their textural properties were determined and dynamics techniques in programmed temperature were used to find the acid properties of the materials. A thermodynamic model was used to determine the adsorption and desorption capacity of chloromethane. Two types of reactions were studied. Firstly the chloromethane was catalytically converted to hydrocarbons (T = 300 450 oC e m = 300 mg) in a fixed bed reactor with controlled pressure and flow. Secondly the deactivation of the unmodified support was studied (at 300 °C and m=250 g) in a micro-adsorver provided of gravimetric monitoring. The metal content (2,5%) and the chloromethane percent of the reagent mixture (10% chloromethane in nitrogen) were fixed for all the tests. From the results the chloromethane conversion and selectivity of the gaseous products (H2, CH4, C3 and C4) were determined as well as the energy of desorption (75,2 KJ/mol for Ni/Al2O3-SiO2 to 684 KJ/mol for the Zn/Al2O3-SiO2 catalyst) considering the desorption rate as a temperature function. The presence of a metal on the support showed to have an important significance in the chloromethane condensation. The oxide class catalyst presented a better performance toward the production of hydrocarbons. Especial mention to the ZnO/Al2O3-SiO2 that, in a gas phase basis, produced C3 83 % max. and C4 63% max., respectively, in the temperature of 450 oC and 20 hours on stream. Hydrogen was produced exclusively in the FeO/Al2O3-SiO2 catalysts (15 % max., T = 550 oC and 5,6 h on stream) and Ni/SiO2-Al2O3 (75 % max., T = 400 oC and 21,6 h on stream). All the catalysts produced methane (10 à 92 %), except for Ni/Al2O3-SiO2 and CrO/Al2O3-SiO2. In the deactivation study two models were proposed: The parallel model, where the product production competes with coke formation; and the sequential model, where the coke formation competes with the product desorption dessorption step. With the mass balance equations and the mechanism proposed six parameters were determined. Two kinetic parameters: the hydrocarbon formation constant, 8,46 10-4 min-1, the coke formation, 1,46 10-1 min-1; three thermodynamic constants (the global, 0,003, the chloromethane adsorption 0,417 bar-1, the hydrocarbon adsorption 2,266 bar-1), and the activity exponent of the coke formation (1,516). The model was reasonable well fitted and presented a satisfactory behavior in relation with the proposed mechanism

Variação da qualidade da água do escoamento superficial de duas bacias de drenagem de Natal/RN - Brasil

The urban drainage is one of the powers of environmental sanitation and its scope is the quantitative and qualitative aspects. In decision making of managers and the engineering aspects of design are almost always taken into account only the quantitative aspects. However, the waters of the runoff have the highest concentrations of pollutants at the beginning of precipitation. Thus, if the plot pollution removed, the remaining portion can be used for other purposes. This work has aimed to present the variation of water quality of two drainage basins in the city of Natal / RN-Brazil to support the implementation of drainage to consider the qualitative aspect, and identify potential for the use of water. The basins (M and C) are analyzed closed-type, are in the urban area, are predominantly residential occupation and its waters are used for detention ponds and infiltration. The samples were divided into three phases, the first two direct to final points in a basin and the third in traps distributed over the surface drainage. The parameters had been analyzed were pH, conductivity, dissolved oxygen, Color, Turbidity, COD, Ammonia, nitrite, nitrate, total phosphorus, orthophosphate, Sediments solids, total solids, chloride, sulfate, alkalinity, calcium, magnesium, sodium, potassium, Heavy Metals (Chromium, Cadmium, Lead, Zinc and Copper), Eschichia coli and total coliforms. The parameters studied showed high initial pollution load, events and located in different proportions, except nitrite, heavy metals and biological indicators. The size of the surface drainage and topographic its features influence the quality of water. However, the form of sampling is crucial in the qualitative study in the basin. The samplers developed at work, were generated economic and representative results. The urban rainwater presents organic faecal indicators. The runoff of water from both basins shows no risk of salinity and sodicity for use in irrigation, should be noted the content of chloride in the choice of method of irrigation

Determinação da composição química do molusco Anadara notabilis encontrado em Galinhos no Rio Grande do Norte

Given the large existing biodiversity in the Brazilian coast, where many species are still little known, even under the nutritional aspect, and considering that bivalve molluscs are constituted by a natural resource of well accepted by the population, chose the bivalve Anadara notabilis, it was not found in the literature any nutritional or toxicological information about it and because its size is much larger than other species of mollusks commonly found in this region. Were studied moisture, ash, protein, macro and micro minerals, and metal ions of toxicological significance. All analytical determinations followed the standards of the Institute Adolfo Lutz. The protein determination was performed by the Kjeldahl method. All metal ions were determined by optical emission spectroscopy with inductively coupled plasma (ICP-OES) method described by USEPA 6010C. The results showed that Anadara notabilis can be introduced into food for human beings, in view of its mineral wealth. Noteworthy among the macronutrients phosphorus and magnesium showed that their values in mg / kg 918.7 and 586.7. With regard to micronutrients stand out with this iron 586.7 mg / kg and zinc with 12.31 mg / kg. Was not found high content of metal contaminants to this mollusc, which would prevent their use, only this chromium 0.7 mg / kg above the value established by Brazilian legislation. The results will certainly be very useful in future studies of nutrition and to build a table of chemical composition of Brazilian foods

Análise bromatológica de carnes antes e após o processamento para obtenção de charque

The process of salting and drying in the sun is used to preserve meat since the beginning of civilization. There is evidence that this preservation technique has arisen in Egypt, between 4,000 and 5,000 years ago. In our country, according to literature, was the first industrial product that gave the appearance of beef jerky, beef being produced, where about 70% to 75% of the muscle is composed of water, where it will be around 45% as a final product, according to the law in his article RIISPOA No. 432 provides that the jerky should contain no more than this amount of moisture in the muscular portion, or more than 15% of total ash with tolerance of up to 5% variation . Besides this parameter, proteins, lipids, ash, and minerals were analyzed in samples before and after the manufacturing process to know the content of these nutrients. Since these are considered important in product quality, thus the concentration in these samples, respectively, in the flesh Front (CD and CHD) before and after the manufacturing process for humidity were respectively 75.28% and 47.38% , the protein was 14.17 and 22.20 g / 100 g sample, 6.360 and 4.251 of lipids g/100g of the sample, and the ashes 0.974 9.144 g/100g sample, minerals like calcium and 4.074 30 , 06 ppm, sódio0, 055 and 5.401 g / L, sodium chloride, 0.139 and 13.74 g / L, potassium 237.5 and 166.8 ppm, 1.721 and 3.295 ppm iron, 0.143 and 0.135 ppm phosphorus, zinc and 4.690 6.905 ppm; magnésio14, 63 e13, 75 ppm manganese .017 e0, 007ppm, copper 0.057 and 0.039 ppm in the case of needle-type meat (CPA and CHPA), 68.04% and 44.17%, protein 13 , 72, and 24.42 g/100g of sample, 1.137 in the ash and 12.68 g / 100g of sample, and the minerals calcium 17.11 and 12.89 ppm; sódio0, 123 and 4.871 g / L, sodium chloride 0.312 and 12.39 g / L, potassium 305.3 and 182.1 ppm; ferro1, 817 and 1.513 ppm, 0.273 and 0.139 ppm phosphorus, zinc 6.305 and 4.783 ppm, 27.95 and 15.85 ppm magnesium, manganese and 0.025 0.011 ppm, 0.057 and 0.143 ppm copper and chromium 0.014 and 0.068 ppm

Avaliação da dolomita funcionalizada para remoção de H2S em gás natural

The natural gas is an alternative source of energy which is found underground in porous and permeable rocks and being associated or not to the oil. Its basic composition includes methane, other hydrocarbon and compounds such as carbon dioxide, nitrogen, sulphidric gas, mercaptans, water and solid particles. In this work, the dolomite mineral, a double carbonate of calcium and magnesium whose the chemical formula is CaMg(CO3)2, was evaluated as adsorbent material. The material was characterized by granulometric analysis, X-ray fluorescence, X-ray diffraction, thermogravimetric analysis, differential thermal analysis, specific surface area, porosity, scanning electronic microscopy and infrared spectroscopy. Then the material was functionalized with diethanolamine (dolomite+diethanolamine) and diisopropylamine (dolomite+diisopropylamine). The results indicated that the adsorbents presented appropriate physiochemical characteristics for H2S adsorption. The adsorption tests were accomplished in a system coupled to a gas chromatograph and the H2S monitoring in the output of the system was accomplished by a pulsed flame photometric detector (PFPD). The adsorbents presented a significant adsorption capacity. Among the analyzed adsorbents, the dolomite+diethanolamine presented the best capacity of adsorption. The breakthrough curves obtained proved the efficiency of this process

Remoção de metais pesados em efluentes sintéticos utilizando vermiculita como adsorvente

Heavy metals are used in many industrial processestheirs discard can harm fel effects to the environment, becoming a serious problem. Many methods used for wastewater treatment have been reported in the literature, but many of them have high cost and low efficiency. The adsorption process has been used as effective for the metal remoal ions. This paper presents studies to evaluate the adsorption capacity of vermiculite as adsorbent for the heavy metals removal in a synthetic solution. The mineral vermiculite was characterized by differents techniques: specific surface area analysis by BET method, X-ray diffraction, raiosX fluorescence, spectroscopy in the infraredd region of, laser particle size analysis and specific gravity. The physical characteristics of the material presented was appropriate for the study of adsorption. The adsorption experiments weredriveal finite bath metod in synthetic solutions of copper, nickel, cadmium, lead and zinc. The results showed that the vermiculite has a high potential for adsorption, removing about 100% of ions and with removal capacity values about 85 ppm of metal in solution, 8.09 mg / g for cadmium, 8.39 mg/g for copper, 8.40 mg/g for lead, 8.26 mg/g for zinc and 8.38 mg/g of nickel. The experimental data fit in the Langmuir and Freundlich models. The kinetic datas showed a good correlation with the pseudo-second order model. It was conducteas a competition study among the metals using vermiculiti a adsorbent. Results showed that the presence of various metals in solution does not influence their removal at low concentrations, removing approximat wasely 100 % of all metals present in solutions

Adição de subprodutos da cinza da casca de café (coffea canephora) em massa cerâmica para porcelanato

To produce porcelain tiles fluxing agents are used in order to obtain a liquid phase during firing. This liquid phase fills the pores decreasing porosity, water absorption and contributes to material densification. In the porcelain tiles industry, feldspar is the main flux material used, with quantities ranging between 35 and 50%. Studies focus on the discovery of materials with flux characteristics that can reduce the consumption of feldspar by porcelain tiles industry. In this context, the coffee husk ashes, a residue obtained when coffee husks are burned to produce heat for the dryers during the processing of the green fruit, have as main chemical constituents potassium, calcium and magnesium, giving them characteristics of fluxing material. Brazil is the largest coffee producer in the world and is responsible for over 30% of the world s production. In this work a physical treatment of coffee husk ash was carried out in order to eliminate the organic matter and, after this, two by-products were obtained: residual wastes R1 and R2. Both residues were added separately as single fluxes and also in association with feldspar in mixtures with raw materials collected in a porcelain industry located in Dias d Ávila-Ba. The addition of these residues aimed to contribute to the reduction of the consumption of feldspar in the production of porcelain tiles. Specimens were produced with dimensions of 60 mm x 20 mm x 6 mm in an uniaxial die with compacting pressure of 45 MPa. The samples were heated to a temperature of 1200 °C, for 8 minutes. Tests were performed to characterize the raw materials by XRF, XRD, particle size analysis, DTA and TGA and, additionally, the results of the physical properties of water absorption, apparent porosity, linear shrinkage, density, dilatometry, flexural strength and SEM of sintered body were analyzed. Additions of less than 8% of the residue R1 contributed to the decrease of porosity, but the mechanical strength of the samples was not satisfactory. Additions of 5% the R2 residue contributed significantly to decrease the water absorption and apparent porosity, and also to increase the mechanical strength. Samples with addition of feldspar associated with the R2 residue, in proportions of 6.7% of R2 and 6.7% of feldspar, led to results of water absorption of 0.12% and mechanical strength of 46 MPa, having parameters normalized to the manufacture of porcelain stoneware tiles

Extração de metais (K, Mg, Ba, Ca, Cr, Mn, Li, Fe) de água produzida utilizando sistema microemulsionado

The produced water is a byproduct formed due to production of petroleum and carries with it a high amount of contaminants such as oil particles in suspension, organic compounds and metals. Thus, these latter pollutants are very difficult to treat because of its high solubility in water. The objective of this work is to use and evaluate a microemulsioned system to remove metals ( K , Mg , Ba , Ca , Cr , Mn , Li , Fe ) of synthetic produced water. For the extraction of metals, it was used a pseudoternary diagram containing the following phases: synthetic produced water as the aqueous phase (AP), hexane as organic phase (OP), and a cosurfactant/surfactant ratio equal to four (C/S = 4) as the third phase, where the OCS (saponified coconut oil) was used as surfactant and n-butanol as cosurfactant. The synthetic produced water was prepared in a bench scale and the region of interest in the diagram for the removal of metals was determined by experimental design called. Ten points located in the phase Winsor II were selected in an area with a large amount of water and small amounts of reagents. The samples were analyzed in atomic absorption spectrometer, and the results were evaluated through a statistical assesment, allowing the efficiency analysis of the effects and their interactions. The results showed percentages of extraction above 90% for the metals manganese, iron, chromium, calcium, barium and magnesium, and around 45% for metals lithium and potassium. The optimal point for the simultaneous removal of metals was calculated using statistical artifact multiple response function (MR). This calculation showed that the point of greatest extraction of metals occurs was the J point, with the composition [72% AP, 9% OP, 19% C/S], obtaining a global extraction percentage about 80%. Considering the aspects analyzed, the microemulsioned system has shown itself to be an effective alternative in the extraction of metals on synthetic produced water remediation

Sensibilidade da cinética do zinco e avaliação nutricional em crianças submetidas ao teste venoso de tolerância ao zinco

Objective: The purpose of this study was to investigate the kinetics of this micronutrient in schoolchildren between the ages of 6 and 9 years, of both sexes, and to verify its sensitivity in detecting alterations in body zinc status. Methods: Nutritional assessment was performed by body mass index. Food intake, venous zinc tolerance test and zinc kinetics were carried out before and after 3-month oral zinc supplementation. Results: Of the 42 children studied, 76.2% had healthy weight. Only energy, calcium and fiber intake were suboptimal before and after oral zinc supplementation. Serum zinc and total-body zinc clearance, although at normal levels, increased significantly after zinc supplementation. Conclusion: We concluded, therefore, that kinetics is a sensitive tool for detecting changes in body zinc status, even in children without a deficiency of this mineral. Furthermore, kinetics showed a positive response to supplementation and may be a sensitive parameter to evaluate the efficacy of this therapy

Fatores litogênicos em pacientes com litíase urinária de Fortaleza, Ceará

Lithiasis is considered a public health issue due to its high prevalence and rates of recurrence. Objective: To identify risk factors for lithiasis in kidney stone patients from Fortaleza, Brazil. In the first stage of the study, the medical records of 197 patients with urinary lithiasis covering the period 1996 2006 were analyzed with regard to clinical and metabolic data. In the second stage, 340 kidney stones were submitted to morphological examination under 10x magnification. According to the external morphology and the cut surface, the stones were classified as pure or mixed, and major and minor components were identified. In addition, the stone fragments of 25 patients treated with lithotripsy were submitted to morphological analysis. In the third stage, a subsample of 50 stones was used in a double-blind comparison of morphological and chemical findings. Results were expressed as concordant, partly concordant (discordant for minor components) or discordant (discordant for major components). The average age of first symptoms was 35.8±13.3 years, with no significant difference between the genders. The male/female ratio was 1:1.7. Recurrence was reported in 53.3% of cases. The main metabolic changes observed were hypernatriuria (80.7%), hypercalciuria (48.7%), low urine volume (43.7%), hyperoxaluria (30.5%) and hyperuricosuria (17.3%). Pure stones represented 34.7% of the total sample of 340 stones. The most common route of elimination was spontaneous for pure stones (49.1%) and surgical for mixed stones (50.5%). Pure stones consisted most frequently of calcium oxalate (OxCa) (59.3%) and uric acid (UA) (23.7%), the former prevalent in women, the latter prevalent in men. The most frequently observed component in mixed stones was OxCa (67.1%), followed by carbapatite (11.2%) and struvite (7.9%). The main components were OxCa and UA for men, and carbapatite and struvite for women. Nearly half (48%) the 25 analyzed fragments were pure, consisting of calcium oxalate dihydrate (COD) (56%), calcium oxalate monohydrate (COM) (48%), phosphate (32%) and UA (20%). Four patients (16%) had infectious stones. In the chemical analysis of the subsample of 50 stones, the most 64 frequently observed major components were calcium (70%), oxalate (66%), ammonium (56%), urate (28%) and carbonate (24%). In the morphological analysis, the main components were calcium and magnesium phosphate (32%), COM (24%), UA (20%), COD (18%) and cystine (6%). Morphological and chemical findings were totally concordant for 38% of the stones, partly concordant in 52% and discordant in 10%. Conclusion: The risk factors for lithiasis in kidney stone patients from Fortaleza (Brazil) were hyperoxaluria, hypercalciuria with or without hypernatriuria, hyperuricosuria and low urine volume

Alterações no metabolismo de zinco relacionadas ao envelhecimento

Although many studies point to alterations in the organic concentrations of zinc in elderly patients, the mechanisms by which aging might cause changes in the metabolism of this nutrient remain unclear. Thus, we assessed the changes in plasma zinc, Zinc Binding Capacity to Plasma Protein (ZnBCPP) and Saturation Index (SI), comparing elderly individuals and young adults. The zinc analyses were performed by atomic absorption spectrophotometry. A statistically significant difference (p < 0.001) was found between the two groups, in relation to plasma zinc and SI, but the ZnBCPP did not differ between the younger and older subjects. In agreement with this result, it was shown in the young group that 76% (R2 = 0.760) of the ZnBCPP variations are explained by the variations in plasma zinc and SI. In the elderly group this measure decreased to 30.5% (R2 = 0.305). We conclude, therefore, that aging may be a factor associated to changes in control mechanisms and in zinc homeostasis, and could even alter ZnBCPP response patterns and other zinc-related indicators of nutritional status.

Influência do tratamento com ácido lipoico sobre o metabolismo ósseo e perfil antioxidante de mulheres na perimenopausa

Bone is a dynamic tissue that is in constant process of remodeling in response to mechanical stress and hormonal changes. This study aimed to understand the relationship between the biochemical changes, which women in the menopausal transition are subject to, and how the use of an alternative therapy with lipoic acid (LA) could influence these changes. The study of double-blind, was carried out in perimenopausal women that underwent a three month treatment with 600 mg of AL compared with another group that received placebo during the same period. This study showed that women had a waist circunference and body mass index above the values recommended by WHO (WC ≥ 80 cm; BMI > 25kg/m2). Associated with this, these women had increased concentrations of total cholesterol and triglycerides, and borderline LDL (Total Cholesterol > 200mg/dL; Triglycerides > 150mg/dL; LDL >130mg/dL). These changes were not affected by treatment with AL. There were no shifts in liver profile (ALT, AST and GGT), kidney profile (urea, creatinine, total protein and albumin), mineral profile (Total Calcium, Ionized Calcium, Phosphorus and Magnesium) as well in bone markers (osteocalcin, Total Alkaline Phosphatase and Tartrate Resistant Acid Phosphatase) after treatment with LA. The results of the oxidative profile showed that treatment with LA decreased GPx activity (p < 0,01), while for the TBARS, GSH and SOD activity there were no differences. With regard to SOD, this enzyme will submit to be high in the placebo group after 3 months of study (p<0,05). The expression of RANKL mRNA was reduced (p < 0,05) and of RANK increased (p <0.001), after treatment with LA, while the expression of IL-6 and TNF-ɑ genes were no changed. We conclude that women already in the perimenopause stage have changes in lipid profile and body composition that could induce shifts in oxidative and bone metabolism. However, LA treatment has provided an effective effect in the oxidative and bone profile since the earliest markers such as GPx activity and mRNA expression of RANKL, respectively, were reduced associated with no change in SOD activity. These results suggest a beneficial and protective effect of LA, indicating it potential as an alternative treatment to help the to prevent the complications associated with estrogen deficiency

Avaliação da presença de osteopatia decorremte do diabetes tipo 1 em criança e adolecentes do Rio Grande do Norte

Diabetes Mellitus (DM) and osteoposes are chronic diseases with great socioeconomic consequences, mainly due to the late complications and consequent disabilities. The potential effects of DM on bone metabolism remain a very conroversial issue, and disagreement exists with regard to the clinical implications of diabetic osteopenia and the mechanism of its ocurrence. The issue is further complicated by the contribuicion of the especific factors, such as duration of disease an dthe degree of metabolic control. The objective of this study is to identify the osteopathy in children and adolescents with DM 1 assisted in the hospital of pediatrics, UFRN, through biochemical markers of bone and mineral metabolism and the extent of bone mineral density. The study was composed by 74 diabetics type 1 patients (DM1) of both gender and aged 6 to 20 yars. Normoglicêmic group was composed by 97 healthy subjects of both genders, which showed the same age range of DM1, in addition to same socioeconomic class. These individuals qere students from the networks of public education in the city of Natal-RN, randomly invited to paticipate in our study. Both groups DM1 and NG were divided intofour subgroups, according to the classification of tanner , T1, T2, T3, T4 for achieving a benchmark. Diabetic individuals showed up with a poor glycemic control. the group DN1 T4 showed an incresead value for total protein, albumin, urea and microalbumiuria are predictors of grumelura injury in DM1 patients . The total alkaline phosphatase activitywas kept on high levels for both groups because they are in a stature development age. For osteocalcin there were decreased levels for groups Dm1 T1, T2, and T3 when compared to their NG (s), suggesting that this decrease could be associated with reduction in the number and/or differentiation os osteoblasts thereby contributing to reducing bone formation. There were no changes in the activity of TRAP. The serum concentrations of total and ionized calcium, phosphorus and magnesium were included within the RV. It was observed that the BMD (Z- SCORE ) has always been within the RV for both groups, despite to DM1 T4. Taking all together, our results support the hypothesis that children and adolescents with type 1 DM present the risk in the long run to suffer a reduction in the bone mass, associated to poor glicemic control and disease duration. It could limit the bone growth and increase the probality of development of osteopenia, as well as other complications surch as retinopathy and renal failure

Avaliação da argila atapulgita para potencial uso como excipiente farmacêutico em formas sólidas

Clays are natural materials that have great potential for use as excipients for solid dosage forms. Palygorskite is a type of clay that has hydrophilic properties as well as a large surface area, which could contribute to the dissolution of drugs. Thus, the present study aims to evaluate the use of palygorskite clay, from Piaui (Northeast region of Brazil), as a pharmaceutical excipient for solid dosage forms, using rifampicin and isoniazid as the model drugs. The former is a poorly soluble drug often associated with isoniazid for tuberculosis treatment. Palygorskite was characterized by X-ray diffraction (XRD), X-ray fluorescence (XRF), particle size, transmission electron microscopy (TEM), scanning electron microscopy (SEM) and specific surface area (BET). The rheological and technological properties of palygorskite were determined and compared to those of talc, magnesium stearate and Aersosil 200. Mixtures between drugs and palygorskite were analyzed by differential scanning calorimetry (DSC), thermogravimetric analysis (TG) combined with thermal analysis (DTA) and Fourier Transform Infrared Spectroscopy (FT-IR), where the results were compared with those of the individual compounds. In addition, dissolution studies of solid dispersions and capsules containing the drugs, mixed with either palygorskite or a mixture of talc and magnesium stearate, were performed. The results showed that palygorskite has small particles with a high surface area. Its rheological characteristics were better than those of others commonly used glidants and lubricants. There was no interaction between palygorskite and the drugs (rifampicin and isoniazid). Among the dispersions studied, the mixture with palygorskite (5%) showed the highest drug dissolution when compared to other excipients. The dissolution of the rifampicin capsules containing palygosrkite was faster in higher concentrations. However, these differences were statistically different only in the first minutes of the dissolution experiment. The dissolution profile of isoniazid was also statistically different on the initial part of the experiment. The formulations prepared with isoniazid and palygorskite showed higher drug dissolution, but it was in descending order of concentration. According to these results, the palygorskite clay used in this study has great potential for application as an excipient for solid dosage forms