Análise de desempenho experimental de redes IEEE 802.3.

The Ethernet technology dominates the market of computer local networks. However, it was not been established as technology for industrial automation set, where the requirements demand determinism and real-time performance. Many solutions have been proposed to solve the problem of non-determinism, which are based mainly on TDMA (Time Division Multiple Access), Token Passing and Master-Slave. This work of research carries through measured of performance that allows to compare the behavior of the Ethernet nets when submitted with the transmissions of data on protocols UDP and RAW Ethernet, as well as, on three different types of Ethernet technologies. The objective is to identify to the alternative amongst the protocols and analyzed Ethernet technologies that offer to a more satisfactory support the nets of the industrial automation and distributed real-time application

Especificação de uma rede MPLS fim-a-fim com diferenciação de serviços

New multimedia applications that use the Internet as a communication media are pressing for the development of new technologies, such as: MPLS (Multiprotocol Label Switching) and DiffServ. These technologies introduce new and powerful features to the Internet backbone, as the provision of QoS (Quality of Service) capabilities. However, to obtain a true end-to-end QoS, it is not enough to implement such technologies in the network core, it becomes indispensable to extend such improvements to the access networks, what is the aim of the several works presently under development. To contribute to this process, this Thesis presents the RSVP-SVC (Resource Reservation Protocol Switched Virtual Connection) that consists in an extension of RSVP-TE. The RSVP-SVC is presented herein as a mean to support a true end-to-end QoS, through the extension of MPLS scope. Thus, it is specified a Switched Virtual Connection (SVC) service to be used in the context of a MPLS User-to-Network Interface (MPLS UNI), that is able to efficiently establish and activate Label Switched Paths (LSP), starting from the access routers that satisfy the QoS requirements demanded by the applications. The RSVP-SVC was specified in Estelle, a Formal Description Technique (FDT) standardized by ISO. The edition, compilation, verification and simulation of RSVP-SVC were made by the EDT (Estelle Development Toolset) software. The benefits and most important issues to be considered when using the proposed protocol are also included

A produção tardia da profissionalização docente e seu impacto na redefinição identitária do professorado do ensino fundamental

El objetivo de este estudio consistió en capturar y reconstituir el modo por el cual profesoras y profesores vinculados a la educación infantil y a la fase inicial de la enseñanza fundamental producen su identidad docente, en el contexto de una tardía profesionalización. El campo de esa pesquisa envolvió tres instituciones públicas de enseñanza superior, dos en Natal (RN) y una en João Pessoa (PB), que desenvulven programas especiales de formación de docentes vinculados a las respectivas redes locales de enseñanza. Para el atendimiento del objetivo arriba propuesto, fue utilizada la teoría de las representaciones sociales para la captura de los elementos constitutivos de las representaciones sociales del profesorado conforme la formulación de Serge Moscovici y colaboradores, considerándose, aqui, especialmente, la contribución de Abric en su complementar teoría de nucleo central de las representaciones. Teniendo en vista la necesidad de identificación de los elementos estructuradores de las representaciones, y definidores de las identidades en cuestión, se privilegió en la pesquisa la producción discursiva docente y sus condiciones de producción. La utilización de sus evocaciones, bien como de las fuentes escritas por los propios sujetos envolvidos, oportunizó el afloramiento de las diferentes faces constitutivas del ser profesor/a . El corpus decorriente de ese estudio fue entonces somentido a una serie de diferentes métodos / técnicas condensadas en programas informatizados y otros manuales en um esfuerzo para conferir un mayor rigor al análisis de los resultados apuntados. Se utilizó, aún, un referencial de análisis del discurso para viabilizar la emergencia de diferentes ângulos de la configuracion de la identidad en foco. Los resultados apuntam para un significativo deslocamiento de las representaciones docentes, bien como permitem afirmar la hipótesis, inicialmente puesta, de que la profesionalización docente ocurre no apenas de manera tardía, como también viene provocando una resignificación de los referentes de identidad de esos profesionales

Utilização de sismos regionais para a determinação de um modelo 1D de velocidades da onda P na Província Borborema - NE do Brasil

In this work it was performed a study to obtain parameters for an 1D regional velocity model for the Borborema Province, NE Brazil. It was used earthquakes occurred between 2001 and 2013 with magnitude greater than 2.9 mb either from epicentres determined from local seismic networks or by back azimuth determination, when possible. We chose seven events which occurred in the main seismic areas in the Borborema Province. The selected events were recorded in up to 74 seismic stations from the following networks: RSISNE, INCT-ET, João Câmara – RN, São Rafael – RN, Caruaru - PE, São Caetano - PE, Castanhão - CE, Santana do Acarau - CE, Taipu – RN e Sobral – CE, and the RCBR (IRIS/USGS—GSN). For the determination of the model parameters were inverted via a travel-time table and its fit. These model parameters were compared with other known model (global and regional) and have improved the epicentral determination. This final set of parameters model, we called MBB is laterally homogeneous with an upper crust at 11,45 km depth and total crustal thickness of 33,9 km. The P-wave velocity in the upper crust was estimated at 6.0 km/s and 6.64 km/s for it lower part. The P-wave velocity in the upper mantle we estimated at 8.21 km/s with an VP/VS ratio of approximately 1.74.

Utilização de sismos regionais para a determinação de um modelo 1D de velocidades da onda P na Província Borborema - NE do Brasil

In this work it was performed a study to obtain parameters for an 1D regional velocity model for the Borborema Province, NE Brazil. It was used earthquakes occurred between 2001 and 2013 with magnitude greater than 2.9 mb either from epicentres determined from local seismic networks or by back azimuth determination, when possible. We chose seven events which occurred in the main seismic areas in the Borborema Province. The selected events were recorded in up to 74 seismic stations from the following networks: RSISNE, INCT-ET, João Câmara – RN, São Rafael – RN, Caruaru - PE, São Caetano - PE, Castanhão - CE, Santana do Acarau - CE, Taipu – RN e Sobral – CE, and the RCBR (IRIS/USGS—GSN). For the determination of the model parameters were inverted via a travel-time table and its fit. These model parameters were compared with other known model (global and regional) and have improved the epicentral determination. This final set of parameters model, we called MBB is laterally homogeneous with an upper crust at 11,45 km depth and total crustal thickness of 33,9 km. The P-wave velocity in the upper crust was estimated at 6.0 km/s and 6.64 km/s for it lower part. The P-wave velocity in the upper mantle we estimated at 8.21 km/s with an VP/VS ratio of approximately 1.74.

Algoritmos genéticos e processamento paralelo aplicados à definição e treinamento de redes neurais perceptron de múltiplas camadas

ln this work, it was deveIoped a parallel cooperative genetic algorithm with different evolution behaviors to train and to define architectures for MuItiIayer Perceptron neural networks. MuItiIayer Perceptron neural networks are very powerful tools and had their use extended vastIy due to their abiIity of providing great resuIts to a broad range of appIications. The combination of genetic algorithms and parallel processing can be very powerful when applied to the Iearning process of the neural network, as well as to the definition of its architecture since this procedure can be very slow, usually requiring a lot of computational time. AIso, research work combining and appIying evolutionary computation into the design of neural networks is very useful since most of the Iearning algorithms deveIoped to train neural networks only adjust their synaptic weights, not considering the design of the networks architecture. Furthermore, the use of cooperation in the genetic algorithm allows the interaction of different populations, avoiding local minima and helping in the search of a promising solution, acceIerating the evolutionary process. Finally, individuaIs and evolution behavior can be exclusive on each copy of the genetic algorithm running in each task enhancing the diversity of populations

Predição de séries temporais de parâmetros de redes HSPA - WCDMA

With the growing demand of data traffic in the networks of third generation (3G), the mobile operators have attempted to focus resources on infrastructure in places where it identifies a greater need. The channeling investments aim to maintain the quality of service especially in dense urban areas. WCDMA - HSPA parameters Rx Power, RSCP (Received Signal Code Power), Ec/Io (Energy per chip/Interference) and transmission rate (throughput) at the physical layer are analyzed. In this work the prediction of time series on HSPA network is performed. The collection of values of the parameters was performed on a fully operational network through a drive test in Natal - RN, a capital city of Brazil northeastern. The models used for prediction of time series were the Simple Exponential Smoothing, Holt, Holt Winters Additive and Holt Winters Multiplicative. The objective of the predictions of the series is to check which model will generate the best predictions of network parameters WCDMA - HSPA.

FTE-LEACH: um protocolo energeticamente eficiente e tolerante a falhas aplicado às redes industriais de sensores sem fio

A Wireless Sensor Network (WSN) consists of distributed devices in an area in order to monitor physical variables such as temperature, pressure, vibration, motion and environmental conditions in places where wired networks would be difficult or impractical to implement, for example, industrial applications of difficult access, monitoring and control of oil wells on-shore or off-shore, monitoring of large areas of agricultural and animal farming, among others. To be viable, a WSN should have important requirements such as low cost, low latency, and especially low power consumption. However, to ensure these requirements, these networks suffer from limited resources, and eventually being used in hostile environments, leading to high failure rates, such as segmented routing, mes sage loss, reducing efficiency, and compromising the entire network, inclusive. This work aims to present the FTE-LEACH, a fault tolerant and energy efficient routing protocol that maintains efficiency in communication and dissemination of data.This protocol was developed based on the IEEE 802.15.4 standard and suitable for industrial networks with limited energy resources

Classificação de distúrbios na rede elétrica usando redes neurais e wavelets

Post dispatch analysis of signals obtained from digital disturbances registers provide important information to identify and classify disturbances in systems, looking for a more efficient management of the supply. In order to enhance the task of identifying and classifying the disturbances - providing an automatic assessment - techniques of digital signal processing can be helpful. The Wavelet Transform has become a very efficient tool for the analysis of voltage or current signals, obtained immediately after disturbance s occurrences in the network. This work presents a methodology based on the Discrete Wavelet Transform to implement this process. It uses a comparison between distribution curves of signals energy, with and without disturbance. This is done for different resolution levels of its decomposition in order to obtain descriptors that permit its classification, using artificial neural networks

Uso de técnicas de otimização baseadas em derivadas como suporte do planejamento operacional de redes de distribuição de energia elétrica

The usual programs for load flow calculation were in general developped aiming the simulation of electric energy transmission, subtransmission and distribution systems. However, the mathematical methods and algorithms used by the formulations were based, in majority, just on the characteristics of the transmittion systems, which were the main concern focus of engineers and researchers. Though, the physical characteristics of these systems are quite different from the distribution ones. In the transmission systems, the voltage levels are high and the lines are generally very long. These aspects contribute the capacitive and inductive effects that appear in the system to have a considerable influence in the values of the interest quantities, reason why they should be taken into consideration. Still in the transmission systems, the loads have a macro nature, as for example, cities, neiborhoods, or big industries. These loads are, generally, practically balanced, what reduces the necessity of utilization of three-phase methodology for the load flow calculation. Distribution systems, on the other hand, present different characteristics: the voltage levels are small in comparison to the transmission ones. This almost annul the capacitive effects of the lines. The loads are, in this case, transformers, in whose secondaries are connected small consumers, in a sort of times, mono-phase ones, so that the probability of finding an unbalanced circuit is high. This way, the utilization of three-phase methodologies assumes an important dimension. Besides, equipments like voltage regulators, that use simultaneously the concepts of phase and line voltage in their functioning, need a three-phase methodology, in order to allow the simulation of their real behavior. For the exposed reasons, initially was developped, in the scope of this work, a method for three-phase load flow calculation in order to simulate the steady-state behaviour of distribution systems. Aiming to achieve this goal, the Power Summation Algorithm was used, as a base for developing the three phase method. This algorithm was already widely tested and approved by researchers and engineers in the simulation of radial electric energy distribution systems, mainly for single-phase representation. By our formulation, lines are modeled in three-phase circuits, considering the magnetic coupling between the phases; but the earth effect is considered through the Carson reduction. It s important to point out that, in spite of the loads being normally connected to the transformer s secondaries, was considered the hypothesis of existence of star or delta loads connected to the primary circuit. To perform the simulation of voltage regulators, a new model was utilized, allowing the simulation of various types of configurations, according to their real functioning. Finally, was considered the possibility of representation of switches with current measuring in various points of the feeder. The loads are adjusted during the iteractive process, in order to match the current in each switch, converging to the measured value specified by the input data. In a second stage of the work, sensibility parameters were derived taking as base the described load flow, with the objective of suporting further optimization processes. This parameters are found by calculating of the partial derivatives of a variable in respect to another, in general, voltages, losses and reactive powers. After describing the calculation of the sensibility parameters, the Gradient Method was presented, using these parameters to optimize an objective function, that will be defined for each type of study. The first one refers to the reduction of technical losses in a medium voltage feeder, through the installation of capacitor banks; the second one refers to the problem of correction of voltage profile, through the instalation of capacitor banks or voltage regulators. In case of the losses reduction will be considered, as objective function, the sum of the losses in all the parts of the system. To the correction of the voltage profile, the objective function will be the sum of the square voltage deviations in each node, in respect to the rated voltage. In the end of the work, results of application of the described methods in some feeders are presented, aiming to give insight about their performance and acuity

Análise e otimização de superfícies seletivas de Frequência utilizando redes neurais artificiais e algoritmos de otimização natural

The bidimensional periodic structures called frequency selective surfaces have been well investigated because of their filtering properties. Similar to the filters that work at the traditional radiofrequency band, such structures can behave as band-stop or pass-band filters, depending on the elements of the array (patch or aperture, respectively) and can be used for a variety of applications, such as: radomes, dichroic reflectors, waveguide filters, artificial magnetic conductors, microwave absorbers etc. To provide high-performance filtering properties at microwave bands, electromagnetic engineers have investigated various types of periodic structures: reconfigurable frequency selective screens, multilayered selective filters, as well as periodic arrays printed on anisotropic dielectric substrates and composed by fractal elements. In general, there is no closed form solution directly from a given desired frequency response to a corresponding device; thus, the analysis of its scattering characteristics requires the application of rigorous full-wave techniques. Besides that, due to the computational complexity of using a full-wave simulator to evaluate the frequency selective surface scattering variables, many electromagnetic engineers still use trial-and-error process until to achieve a given design criterion. As this procedure is very laborious and human dependent, optimization techniques are required to design practical periodic structures with desired filter specifications. Some authors have been employed neural networks and natural optimization algorithms, such as the genetic algorithms and the particle swarm optimization for the frequency selective surface design and optimization. This work has as objective the accomplishment of a rigorous study about the electromagnetic behavior of the periodic structures, enabling the design of efficient devices applied to microwave band. For this, artificial neural networks are used together with natural optimization techniques, allowing the accurate and efficient investigation of various types of frequency selective surfaces, in a simple and fast manner, becoming a powerful tool for the design and optimization of such structures

Um protocolo de comunicação multicast na camada de aplicação com Consciência de Localização

Internet applications such as media streaming, collaborative computing and massive multiplayer are on the rise,. This leads to the need for multicast communication, but unfortunately group communications support based on IP multicast has not been widely adopted due to a combination of technical and non-technical problems. Therefore, a number of different application-layer multicast schemes have been proposed in recent literature to overcome the drawbacks. In addition, these applications often behave as both providers and clients of services, being called peer-topeer applications, and where participants come and go very dynamically. Thus, servercentric architectures for membership management have well-known problems related to scalability and fault-tolerance, and even peer-to-peer traditional solutions need to have some mechanism that takes into account member's volatility. The idea of location awareness distributes the participants in the overlay network according to their proximity in the underlying network allowing a better performance. Given this context, this thesis proposes an application layer multicast protocol, called LAALM, which takes into account the actual network topology in the assembly process of the overlay network. The membership algorithm uses a new metric, IPXY, to provide location awareness through the processing of local information, and it was implemented using a distributed shared and bi-directional tree. The algorithm also has a sub-optimal heuristic to minimize the cost of membership process. The protocol has been evaluated in two ways. First, through an own simulator developed in this work, where we evaluated the quality of distribution tree by metrics such as outdegree and path length. Second, reallife scenarios were built in the ns-3 network simulator where we evaluated the network protocol performance by metrics such as stress, stretch, time to first packet and reconfiguration group time

Técnicas de simplificação de redes e otimização multiobjetivo para análise de variações de tensão em regime permanente provocadas por parques eólicos integrados ao sistema elétrico

This study presents a description of the development model of a representation of simplified grid applied in hybrid load flow for calculation of the voltage variations in a steady-state caused by the wind farm on power system. Also, it proposes an optimal load-flow able to control power factor on connection bar and to minimize the loss. The analysis process on system, led by the wind producer, it has as base given technician supplied by the grid. So, the propose model to the simplification of the grid that allows the necessity of some knowledge only about the data referring the internal network, that is, the part of the network that interests in the analysis. In this way, it is intended to supply forms for the auxiliary in the systematization of the relations between the sector agents. The model for simplified network proposed identifies the internal network, external network and the buses of boulders from a study of vulnerability of the network, attributing them floating liquid powers attributing slack models. It was opted to apply the presented model in Newton-Raphson and a hybrid load flow, composed by The Gauss-Seidel method Zbarra and Summation Power. Finally, presents the results obtained to a developed computational environment of SCILAB and FORTRAN, with their respective analysis and conclusion, comparing them with the ANAREDE

Identificação fuzzy-multimodelos para sistemas não lineares

This paper presents a new multi-model technique of dentification in ANFIS for nonlinear systems. In this technique, the structure used is of the fuzzy Takagi-Sugeno of which the consequences are local linear models that represent the system of different points of operation and the precursors are membership functions whose adjustments are realized by the learning phase of the neuro-fuzzy ANFIS technique. The models that represent the system at different points of the operation can be found with linearization techniques like, for example, the Least Squares method that is robust against sounds and of simple application. The fuzzy system is responsible for informing the proportion of each model that should be utilized, using the membership functions. The membership functions can be adjusted by ANFIS with the use of neural network algorithms, like the back propagation error type, in such a way that the models found for each area are correctly interpolated and define an action of each model for possible entries into the system. In multi-models, the definition of action of models is known as metrics and, since this paper is based on ANFIS, it shall be denominated in ANFIS metrics. This way, ANFIS metrics is utilized to interpolate various models, composing a system to be identified. Differing from the traditional ANFIS, the created technique necessarily represents the system in various well defined regions by unaltered models whose pondered activation as per the membership functions. The selection of regions for the application of the Least Squares method is realized manually from the graphic analysis of the system behavior or from the physical characteristics of the plant. This selection serves as a base to initiate the linear model defining technique and generating the initial configuration of the membership functions. The experiments are conducted in a teaching tank, with multiple sections, designed and created to show the characteristics of the technique. The results from this tank illustrate the performance reached by the technique in task of identifying, utilizing configurations of ANFIS, comparing the developed technique with various models of simple metrics and comparing with the NNARX technique, also adapted to identification

Uso de técnicas de otimização baseadas em derivadas como suporte do planejamento operacional de redes de distribuição de energia elétrica

The usual programs for load flow calculation were in general developped aiming the simulation of electric energy transmission, subtransmission and distribution systems. However, the mathematical methods and algorithms used by the formulations were based, in majority, just on the characteristics of the transmittion systems, which were the main concern focus of engineers and researchers. Though, the physical characteristics of these systems are quite different from the distribution ones. In the transmission systems, the voltage levels are high and the lines are generally very long. These aspects contribute the capacitive and inductive effects that appear in the system to have a considerable influence in the values of the interest quantities, reason why they should be taken into consideration. Still in the transmission systems, the loads have a macro nature, as for example, cities, neiborhoods, or big industries. These loads are, generally, practically balanced, what reduces the necessity of utilization of three-phase methodology for the load flow calculation. Distribution systems, on the other hand, present different characteristics: the voltage levels are small in comparison to the transmission ones. This almost annul the capacitive effects of the lines. The loads are, in this case, transformers, in whose secondaries are connected small consumers, in a sort of times, mono-phase ones, so that the probability of finding an unbalanced circuit is high. This way, the utilization of three-phase methodologies assumes an important dimension. Besides, equipments like voltage regulators, that use simultaneously the concepts of phase and line voltage in their functioning, need a three-phase methodology, in order to allow the simulation of their real behavior. For the exposed reasons, initially was developped, in the scope of this work, a method for three-phase load flow calculation in order to simulate the steady-state behaviour of distribution systems. Aiming to achieve this goal, the Power Summation Algorithm was used, as a base for developping the three phase method. This algorithm was already widely tested and approved by researchers and engineers in the simulation of radial electric energy distribution systems, mainly for single-phase representation. By our formulation, lines are modeled in three-phase circuits, considering the magnetic coupling between the phases; but the earth effect is considered through the Carson reduction. Its important to point out that, in spite of the loads being normally connected to the transformers secondaries, was considered the hypothesis of existence of star or delta loads connected to the primary circuit. To perform the simulation of voltage regulators, a new model was utilized, allowing the simulation of various types of configurations, according to their real functioning. Finally, was considered the possibility of representation of switches with current measuring in various points of the feeder. The loads are adjusted during the iteractive process, in order to match the current in each switch, converging to the measured value specified by the input data. In a second stage of the work, sensibility parameters were derived taking as base the described load flow, with the objective of suporting further optimization processes. This parameters are found by calculating of the partial derivatives of a variable in respect to another, in general, voltages, losses and reactive powers. After describing the calculation of the sensibility parameters, the Gradient Method was presented, using these parameters to optimize an objective function, that will be defined for each type of study. The first one refers to the reduction of technical losses in a medium voltage feeder, through the installation of capacitor banks; the second one refers to the problem of correction of voltage profile, through the instalation of capacitor banks or voltage regulators. In case of the losses reduction will be considered, as objective function, the sum of the losses in all the parts of the system. To the correction of the voltage profile, the objective function will be the sum of the square voltage deviations in each node, in respect to the rated voltage. In the end of the work, results of application of the described methods in some feeders are presented, aiming to give insight about their performance and acuity