Construção, caracterização e aplicação de eletrodos para descarga por arco de cátodo oco

The system built to characterize electrodes and, consequently, deposited fine films are constituted by a hollow cathode that works to discharges and low pressures (approximately 10-3 to 5 mbar), a source DC (0 to 1200 V), a cylindrical camera of closed borossilicato for flanges of stainless steel with an association of vacuum bombs mechanical and spread. In the upper flange it is connected the system of hollow cathode, which possesses an entrance of gas and two entrances for its refrigeration, the same is electrically isolated of the rest of the equipment and it is polarized negatively. In front of the system of hollow cathode there is a movable sample in stainless steel with possibility of moving in the horizontal and vertical. In the vertical, the sample can vary its distance between 0 and 70 mm and, in the horizontal, can leave completely from the front of the hollow cathode. The sample and also the cathode hollow are equipped with cromel-alumel termopares with simultaneous reading of the temperatures during the time of treatment. In this work copper electrodes, bronze, titanium, iron, stainless steel, powder of titanium, powder of titanium and silício, glass and ceramic were used. The electrodes were investigated relating their geometry change and behavior of the plasma of the cavity of hollow cathode and channel of the gas. As the cavity of hollow cathode, the analyzed aspects were the diameter and depth. With the channel of the gas, we verified the diameter. In the two situations, we investigated parameters as flow of the gas, pressure, current and applied tension in the electrode, temperature, loss of mass of the electrode with relationship at the time of use. The flow of gas investigated in the electrodes it was fastened in a work strip from 15 to 6 sccm, the constant pressure of work was among 2.7 to 8 x 10-2 mbar. The applied current was among a strip of work from 0,8 to 0,4 A, and their respective tensions were in a strip from 400 to 220 V. Fixing the value of the current, it was possible to lift the curve of the behavior of the tension with the time of use. That curves esteem in that time of use of the electrode to its efficiency is maximum. The temperatures of the electrodes were in the dependence of that curves showing a maximum temperature when the tension was maximum, yet the measured temperatures in the samples showed to be sensitive the variation of the temperature in the electrodes. An accompaniment of the loss of mass of the electrode relating to its time of use showed that the electrodes that appeared the spherical cavities lost more mass in comparison with the electrodes in that didn't appear. That phenomenon is only seen for pressures of 10-2 mbar, in these conditions a plasma column is formed inside of the channel of the gas and in certain points it is concentrated in form of spheres. Those spherical cavities develop inside of the channel of the gas spreading during the whole extension of the channel of the gas. The used electrodes were cut after they could not be more used, however among those electrodes, films that were deposited in alternate times and the electrodes that were used to deposit films in same times, those films were deposited in the glass substrata, alumina, stainless steel 420, stainless steel 316, silício and steel M2. As the eletros used to deposit films in alternate time as the ones that they were used to deposit in same times, the behavior of the thickness of the film obeyed the curve of the tension with relationship the time of use of the electrode, that is, when the tension was maximum, the thickness of the film was also maximum and when the tension was minimum, the thickness was minimum and in the case where the value of the tension was constant, the thickness of the film tends to be constant. The fine films that were produced they had applications with nano stick, bio-compatibility, cellular growth, inhibition of bacterias, cut tool, metallic leagues, brasagem, pineapple fiber and ornamental. In those films it was investigated the thickness, the adherence and the uniformity characterized by sweeping electronic microscopy. Another technique developed to assist the production and characterization of the films produced in that work was the caloteste. It uses a sphere and abrasive to mark the sample with a cap impression, with that cap form it is possible to calculate the thickness of the film. Through the time of life of the cathode, it was possible to evaluate the rate of waste of its material for the different work conditions. Values of waste rate up to 3,2 x 10-6 g/s were verified. For a distance of the substratum of 11 mm, the deposited film was limited to a circular area of 22 mm diameter mm for high pressures and a circular area of 75 mm for pressure strip. The obtained films presented thickness around 2,1 µm, showing that the discharge of arch of hollow cathode in argon obeys a curve characteristic of the tension with the time of life of the eletrodo. The deposition rate obtained in this system it is of approximately 0,18 µm/min

Significados e percepções de puérperas sobre as síndromes hipertensivas da gravidez e parto prematuro

Hypertensive syndromes in pregnancy (HSP) are configured as one of the major complications in the pregnancy and postpartum period and can lead premature newborn and subsequent hospitalization of the newborn to the Neonatal Intensive Care Unit (NICU). This study aimed to analyze the perceptions, meanings and feelings of mothers on the hypertensive syndromes in pregnancy and premature obstetric labor. The research was qualitative and has a theoretical methodological the Social Representations Theory(SRT) in the approach to the Central Nucleus Theory. The study included 70 women, mean age 29 years, predominantly school to high school, most of them married or in consensual union, primiparous and prevalence of cesarean delivery occurred between 32 and 37 weeks of pregnancy.The data were collected from may to december 2008 in the Maternity School Januário Cicco in Natal , and obtained through the following instruments for data collection: questionnaire including questions about socio-demographic status; the Free Words Association Test (FWAT) and and verbalized mental image construction used three stimuli: such as pregnancy with high blood pressure, preterm birth and NICU, and interview with the following guiding question: what it meant for you to have a pregnancy with high blood pressure and consequently the birth of a premature baby? Data analysis was performed using multi-method obtained from the data processing by EVOC (Ensemble Programmes Permettant L 'Analyze des Évocations) and ALCESTE (Analyse Lexicale par Contexte d'un Ensemble de Segment de Texte) and thematic analysis in categories. The results will be presented in four thematic units under the following representative universes: HSP, prematurity as a result of HSP, NICU and the social representations of mothers on the hypertensive disorder of pregnancy sequenced premature birth and hospitalization of the child in the NICU. The results obtained by multimethod analyses showed similar constructions and point to death as the central nucleus and negative aspects, coping strategies, need of care, knowledge about the disease, fragility and meanings of the NICU as peripheral elements. It is considered that the perceptions, meanings and feelings of puerperal women in relation to HSPs and to premature delivery are a negative social representation, with representational elements that may have influenced the adverse effects on the disease and its consequences. We suggest action on the peripheral elements of this representation, with adequate orientation, early diagnosis, effective conduct, receptive attitude on the part of the team, health promotion measures and effective public policies, in order to improve the care provided to puerperal women, making them feel welcome and minimizing their suffering

Desmame em recém-nascidos de muito baixo peso ao nascer no primeiro retorno ambulatorial após a alta hospitalar

Investigate intrahospital and neonatal determinants associated to the weaning of very low birth weight (VLBW) infants. Methods: 119 VLBW (<1500g) infants 81 were monitored from July 2005 through August 2006, from birth to the first ambulatory visit after maternity discharge. This maternity unit uses the Kangaroo Method and the Baby Friendly Hospital Initiative. Results: Out of 119 VLBW infants monitored until discharge, 88 (75%) returned to the facility, 22 (25%) were on exclusive breastfeeding (EB) and 66 (75%) were weaned (partial breastfeeding or formula feeding). Univariate analysis found an association between weaning and lower birth weight, longer stays in the NICU and longer hospitalization times, in addition to more prolonged enteral feeding and birth weight recovery period. Logistic regression showed length of NICU stay as being the main determinant of weaning. Conclusion: The negative repercussion on EB of an extended stay in the NICU is a significant challenge for health professionals to provide more adequate nutrition to VLBW infants

Intencionalidades e práticas na construção de metodologias o CEFET-SE

Successive curricular changes that occurred in professional education altered pedagogical practices, and these practices being developed by means of integrating projects, at Centro Federal de Educação Tecnológica de Sergipe (CEFET-SE), between 2001 and 2003, originated some questions which became the study object of this thesis. We search for theoretical support mainly in GEPEM research (GEPEM/UFRN) works and practices in order to analyze elements that emerged from this pedagogical practice. To do so, we take as main reference the research of qualitative approach. We developed documents analysis, interviews, considering three aspects: the scenery where these changes took place, the conception and implementation of the Integrating Projects for what, we ask support in pedagogy of projects studies and principles of interdisciplinary, and contextualization as curriculum structuring elements. This research brought out some difficulties, conflicts and possible consensus in developing the methodological strategies for the Projects. In this process of coexistence of the traditional and the new, of an unavoidable distance between what was thought and what was effectively done, elements for a new pedagogical practice emerged. This could be noticed in terms of participative work, formative moments, teacher s autonomy related to the pedagogical work. A new door could be open to the possibilities of taking conscience of accepting the differences and oneself autoexperimentation. These are the possibilities that make men, not being mere information deposit, can dialog and transform, producing his existence by this means. In the present case, the existence of being teacher, the build himself in the time of possibilities

Ações de profissionais relativas ao banco de leite humano : uma perspectiva de mudança

This is an exploratory and descriptive study that aimed to investigate the actions of professionals in the context of breastfeeding, on the assumption that the actions taken by employees working together to postpartum and newborn are not competing to effect the distribution of pasteurized human milk so that it meets the needs of infants who depend on it. Thus, the study aimed to analyze the actions of medical and nursing staff of the distribution of pasteurized human milk to the newly born. The investigation was developed by action research in a federal hospital, located in the capital the state of Rio Grande do Norte, Brazil, reference assistance to women during pregnancy, childbirth and postpartum high risk in 2010. Study participants were fifty-five professionals chosen from the following inclusion criteria: to act in the NICU or rooming, being a pediatrician and / or neonatologists, nurses and technical nursing. According to the methodology of action research a questionnaire was applied, techniques in focus groups and courses were developed, and, finally, action evaluation. The project was submitted to the Ethics Committee at the Federal University of Rio Grande do Norte and approved with no protocol 448/2009. The problems identified in the responses issued by the social research were grouped into categories according to the similarity between them. The answer to the question of the survey - How is the need for pasteurized human milk for the newborns in neonatal intensive care unit and rooming identified? - Brought subsidies for action planning and implementation of strategies for change in the practice of professionals working in rooming and ICU. Thus, the study has relevance in social care and, when at the local level, will compete for the distribution pasteurized human milk to take effect as best as possible, as recommended by the Ministry of Health. It is also conceived that, in a macro view of society, it could contribute to minimizing the health problem that involves the child population

Clima e cultura de segurança do paciente em uma maternidade escola: percepção dos profissionais de enfermagem em terapia intensiva

Since the publication of the report "To Err is Human" by the Institute of Medicine (IOM) , which estimated that between 44.000 to 98.000 Americans die annually as a result of errors in health care, patient safety spent gaining prominence, emerging studies assess the safety culture by measuring the safety climate. In this context, the aim of this study was to identify safety culture perceived by nursing professionals working in the intensive care unit of a maternity school in Natal/RN through the Security Attitudes Questionnaire (SAQ). This was a descriptive study, cross-sectional and quantitative approach undertaken in the Intensive Care Unit Maternal and Neonatal a maternity school in Natal/RN. The project was submitted to and approved by Brazil Platform Zip/UFRN under number 309 540 and CAAE 16489713.7.0000.5537. It was used to collect data two instruments: a questionnaire in order to collect socio-demographic data of the subjects and the Questionário Atitudes de Segurança , a cultural adaptation to Portuguese of the instrument of the World Health Organization titled Safety Attitudes Questionnaire - (SAQ ) Short Form 2006. The collected data were analyzed quantitatively by the organization in electronic databases in Microsoft Excel 2010 spreadsheet and exported to statistical software for free access to be coded, tabulated and analyzed using descriptive statistics. The study included a total of 50 nurses, 31 and 19 of the NICU Maternal ICU, predominantly female, mean age 35 years, median time of 10 years training and working in maternity, mostly, less than 05 anos. As a result, two articles were produced. The first refers to the first two domains of the instrument entitled "climate of teamwork" and "climate security" . The scores of the two areas were slightly higher in Maternal ICU compared to the NICU, but no sector has reached the ideal minimum score of 75: in the first domain Maternal ICU had an average of 74.77, with medians of 75 and 100, while Neonatal ICU reached an average of 69.61 with median also 75 and 100, while the second field means were 69.35 and 66.01 for Maternal and Neonatal ICUs respectively, with a median of 100 in the two sectors. The second article relates to the field "Perception Management Unit and Hospital", which 9 assessed the perception of management units and motherhood by professionals. In general, the items of the domain in question also obtained scores below the ideal minimum: 63.68 to 51.02 and maternal ICU for neonatal, featuring a clear separation between the management and the professionals who work in direct care. These findings indicate a warning sign for the institution and point to the need to implement actions aimed at patient safety

Estudo de formulação de massa para aplicação em placas cerâmicas

The sector of civil construction is strongly related to the red ceramic industry. This sector uses clay as raw material for manufacturing of various products such as ceramic plates. In this study, two types of clay called clay 1 and clay 2 were collected on deposit in Ielmo Marinho city (RN) and then characterized by thermogravimetric analysis (TG/DTG), differential thermal analysis (DTA), X-ray diffraction (XRD), X-ray fluorescence (XRF), rational analysis and particle size distribution and dilatometric analyses. Ceramic plates were manufactured by uniaxial pressing and by extrusion. The plates obtained by pressing were produced from the four formulations called 1, 2, 3 and 4, which presented, respectively, the following proportions by mass: 66.5% clay 1 and 33.5% clay 2, 50% clay 1 and 50% clay 2, 33.5% clay 1 and 66.5% clay 2, 25% clay 1 and 75% clay 2. After firing at 850, 950 and 1050 °C with heating rate of 10 °C/min and soaking time of 30 minutes, the following technological properties were determined: linear firing shrinkage, water absorption, apparent porosity, apparent specific mass and tensile strength (3 points). The formulation containing 25% clay 1 produced plates with most satisfactory results of water absorption and mechanical resistance, because of that it was chosen for manufacturing plates by extrusion. A single firing cycle was established for these plates, which took place as follow: heating rate of 2 °C/min up to 600 ºC with soaking time of 60 minutes, followed by heating using the same rate up to 1050 ºC with soaking time of 30 minutes. After this cycle, the same technological properties investigated in the plates obtained by pressing were determined. The results indicate (according to NRB 13818/1997) that the plates obtained by pressing from the mixture containing 25 wt% clay 1, after firing at 1050 °C, reach the specifications for semi-porous coating (BIIb). On the other hand, the plates obtained by extrusion were classified as semi-stoneware (group AIIa)

Modelagem e simulação da deposição de parafinas em escoamento turbulento

The flow assurance has become one of the topics of greatest interest in the oil industry, mainly due to production and transportation of oil in regions with extreme temperature and pressure. In these operations the wax deposition is a commonly problem in flow of paraffinic oils, causing the rising costs of the process, due to increased energy cost of pumping, decreased production, increased pressure on the line and risk of blockage of the pipeline. In order to describe the behavior of the wax deposition phenomena in turbulent flow of paraffinic oils, under different operations conditions, in this work we developed a simulator with easy interface. For that we divided de work in four steps: (i) properties estimation (physical, thermals, of transport and thermodynamics) of n-alkanes and paraffinic mixtures by using correlations; (ii) obtainment of the solubility curve and determination the wax appearance temperature, by calculating the solid-liquid equilibrium of parafinnic systems; (iii) modelling wax deposition process, comprising momentum, mass and heat transfer; (iv) development of graphic interface in MATLAB® environment for to allow the understanding of simulation in different flow conditions as well as understand the matter of the variables (inlet temperature, external temperature, wax appearance temperature, oil composition, and time) on the behavior of the deposition process. The results showed that the simulator developed, called DepoSim, is able to calculate the profile of temperature, thickness of the deposit, and the amount of wax deposited in a simple and fast way, and also with consistent results and applicable to the operation

Monitoramento por dgps e análise dos processos erosivos da linha de costa na praia de Pirangi do Norte - Parnamirim / RN

Through out the course of a steady increase in search and recovery of space in the coastal zone, there is also an expanding concern about the erosion processes of this area. The main problem in coastal areas is that urbanization occurs in a disorderly fashion and unsustainable, further aggravating the problems of coastal dynamics. The study area of this work is located on the southern coast of Pirangi do Norte beach to about 20km south of Natal, capital of Rio Grande do Norte in the Parnamirim City. This area has the length of approximately 1km, divided into three sections (Western, Central and Eastern) with a morphology consisting of a tableland at the top, sea cliffs in the West and Central parts and sand dunes in the Eastern section, both vegetated, and a coastal plain on the inferior part associated with the presence of beach rocks. This study aimed to analyze the erosion processes operating in the excerpt of Pirangi do Norte beach and assess the feasibility of their monitoring making use of DGPS (Global Positioning System Differential mode). During the work it was carried out a physical description of the area through photo-interpretation and site survey after measurement of the shoreline in the period between November 2004 and November 2009 and beach profiles between August 2005 and July 2006. The analysis of the results of the annual surveys showed the occurrence of variations of the shoreline along the stretch traveled. Sites are identified in advancement coast from the sea and it was verified in loco the presence of erosion with deposition of materials on the lower part of the coastal bluff, the former position of the shoreline, showing a false notion of advancing it. This leads to the conclusion that the data collected in a survey of the shoreline should always be accompanied by photographic records of the local area and with the highest rate of erosion, thus avoiding the mistake of treating the deposit materials as evidence of progress coast. At the end of the study, after a review of various works to mitigate the erosion in the coastal zone, it is recommended to the area of study the adoption of an artificial feeding of the beach, aiming the minimization of the erosive effects of the tides. Moreover, it is suggested that even the continuity of monitoring, maintenance of existing vegetation and control of the occupation on the edge of sea cliffs

Impacto do abastecimento irregular de água nos altos índices de dengue

Dengue fever is an infectious disease that causes thousands of deaths each year in Brazil and other tropical countries. This work demonstrates that the irregularity in the supply of water by public water supply systems is a major factor that contributes to the proliferation of breeding sites of the mosquito that transmits dengue, due to the impossibility of removing water storage tanks. 31 points in the water supply network in thirteen districts of Natal, Brazil, were monitored by the installation of pressure gauges type Datalogger. The data about pressure showed deficiency in water supplies in many neighborhoods, forcing residents to accumulate water in tanks at ground level. In addition, It was observed that in neighborhoods with regular water supply, Infestation Index per type of container (ITR) of type A2 (Deposit ground level) was 0.00% and where there were failures in the supply of water , the ITR was high (above 50%). We believe that policies to combat dengue in Brazil should be reassessed so that more resources can be directed to the improvement of water supply systems and supply companies should be blamed for the problem too

Deposição de A/N por sputtering não reativo

In this work we deposit via non-reactive magnetron sputtering of radio-frequency nanofilmes of nitreto of aluminum(AlN). The nanofilms aluminum nitride are semiconductors materials with high thermal conductivity, high melting point, piezoelectricity and wide band gap (6, 2 eV) with hexagonal wurtzite crystal structure, belonging to the group of new materials called III-V nitrides in which together with the gallium nitride and indium nitride have attracted much interest because they have physical and chemical properties relevant to new technological applications, mainly in microelectronic and optoelectronic devices. Three groups were deposited with thicknesses nanofilms time dependent on two substrates (glass and silicon) at a temperature of 25 ° C. The nanofilms AlN were characterized using three techniques, X-ray diffraction, Raman spectroscopy and atomic force microscopy (AFM), examined the morphology of these. Through the analysis of X-rays get the thickness of each sample with its corresponding deposition rate. The analysis of X-rays also revealed that nanofilms are not crystalline, showing the amorphous character of the samples. The results obtained by the technique, atomic force microscopy (AFM) agree with those obtained using the technique of X-rays. Characterization by Raman spectroscopy revealed the existence of active modes characteristic of AlN in the samples

Desenvolvimento e caracterização de dispositivos para reposição de filmes finos por descarga em cátodo oco

In the present work we use a plasma jet system with a hollow cathode to deposit thin TiO2 films on silicon substrates as alternative at sol-gel, PECVD, dip-coating e magnetron sputtering techniques. The cylindrical cathode, made from pure titanium, can be negatively polarized between 0 e 1200 V and supports an electrical current of up to 1 A. An Ar/O2 mixture, with a total flux of 20 sccm and an O2 percentage ranging between 0 and 30%, is passed through a cylindrical hole machined in the cathode. The plasma parameters and your influence on the properties of deposited TiO2 films and their deposition rate was studied. When discharge occurs, titanium atoms are sputtered/evaporated. They are transported by the jet and deposited on the Si substrates located on the substrate holder facing the plasma jet system at a distance ranging between10 and 50 mm from the cathode. The working pressure was 10-3 mbar and the deposition time was 10 -60 min. Deposited films were characterized by scanning electron microscopy and atomic force microscopy to check the film uniformity and morphology and by X-ray diffraction to analyze qualitatively the phases present. Also it is presented the new dispositive denominate ionizing cage, derived from the active screen plasma nitriding (ASPN), but based in hollow cathode effect, recently developed. In this process, the sample was involved in a cage, in which the cathodic potential was applied. The samples were placed on an insulator substrate holder, remaining in a floating potential, and then it was treated in reactive plasma in hollow cathode regime. Moreover, the edge effect was completely eliminated, since the plasma was formed on the cage and not directly onto the samples and uniformity layer was getting in all sampl

Caracterização magnética e estrutural de filmes depositados por gaiola catódica

Iron nitrite films, with hundred of nanometers thick, were deposited using the Cathodic cage plasma nitriding method, with a N2/H2 plasma, over a common glass substract. The structure, surface morphology and magnetic properties were investigated using X-ray diffractometry (XRD), atomic force microscopy (AFM) and vibrating sample magnetometer (VSM). XRD shows the formation of γ FeN phase and a combination of ζFe2N + ɛFe3N phases. The film s saturation magnetization and coercivity depends on morphology, composition, grain size and treatment temperature. Temperature raising from 250 ºC to 350 ºC were followed by an increase in saturation magnetization and film s surface coercivity on the parallel direction in relative proportion. This fact can be attributed to the grain sizes and to the different phases formed, since iron rich fases, like the ɛFe3N phase, emerges more frequently on more elevated treatment s temperature. Using this new and reasonably low cost method, it was possible to deposit films with both good adhesion and good magnetic properties, with wide application in magnetic devices

Caracterização de resíduo sólido formado em biodiesel de sebo bovino

Biodiesel production has increased over the last decade because of the benefits associated with this fuel, including renewability, domestic feedstock, lower toxicity, and biodegradability. From 2008, the use of beef tallow as a feedstock for biodiesel production in Brazil has increased in significance, representing the second largest source of biodiesel, after soybeans. However, the performance of biodiesel in cold weather conditions is worse than diesel because of deposition of insoluble at low temperatures, accelerating the plugging of fuel filters and injectors of the vehicle engine. Studies have been conducted on beef tallow biodiesel, mostly related to the properties of thermal and oxidative stability. However, few studies have described the nature of the precipitate formed and its influence on product quality. Research suggests that the cause of deposition is related to the nature of saturated esters and monoacylglycerols as inducing agents. This study monitored the levels of mono-, diand triacylglycerols, the oxidation stability and the cold filter plugging point (CFPP) in beef tallow biodiesel samples from two commercial producers in Brazil for a period of twelve months. Filtered precipitates were analyzed by comparative techniques of GCFID, HPLC-UV/VIS, HPLC-MS-IT-TOF and TG to verify the nature, using monopalmitin and monostearin as reference standards. The formation of precipitate reduced the levels of monoacylglycerols in the beef tallow biodiesel. GC-FID and LCMS- IT-TOF results confirmed the nature of the deposit as saturated monoacylglycerols, predominantly monostearin and monopalmitin as the second major component. Moreover the TG analysis of the residue indicated similar thermal decomposition of the reference standards. The precipitate did not affect the oxidation stability of beef tallow biodiesel and the CFPP characteristic of blends up B60. However, the presence of iron reduced significantly the oxidation stability of biodiesel

Caracterização de resíduo sólido formado em biodiesel de sebo bovino

Biodiesel production has increased over the last decade because of the benefits associated with this fuel, including renewability, domestic feedstock, lower toxicity, and biodegradability. From 2008, the use of beef tallow as a feedstock for biodiesel production in Brazil has increased in significance, representing the second largest source of biodiesel, after soybeans. However, the performance of biodiesel in cold weather conditions is worse than diesel because of deposition of insoluble at low temperatures, accelerating the plugging of fuel filters and injectors of the vehicle engine. Studies have been conducted on beef tallow biodiesel, mostly related to the properties of thermal and oxidative stability. However, few studies have described the nature of the precipitate formed and its influence on product quality. Research suggests that the cause of deposition is related to the nature of saturated esters and monoacylglycerols as inducing agents. This study monitored the levels of mono-, diand triacylglycerols, the oxidation stability and the cold filter plugging point (CFPP) in beef tallow biodiesel samples from two commercial producers in Brazil for a period of twelve months. Filtered precipitates were analyzed by comparative techniques of GCFID, HPLC-UV/VIS, HPLC-MS-IT-TOF and TG to verify the nature, using monopalmitin and monostearin as reference standards. The formation of precipitate reduced the levels of monoacylglycerols in the beef tallow biodiesel. GC-FID and LCMS- IT-TOF results confirmed the nature of the deposit as saturated monoacylglycerols, predominantly monostearin and monopalmitin as the second major component. Moreover the TG analysis of the residue indicated similar thermal decomposition of the reference standards. The precipitate did not affect the oxidation stability of beef tallow biodiesel and the CFPP characteristic of blends up B60. However, the presence of iron reduced significantly the oxidation stability of biodiesel