Construção de um aparato experimental para monitoramento in situ da deposição de filmes finos de titânio por magnetron sputtering

The technique of surface coating using magnetron sputtering is one of the most widely used in the surface engineering, for its versatility in obtaining different films as well as in the micro / nanometric thickness control. Among the various process parameters, those related to the active species of the plasma are of the most fundamental importance in the mechanism and kinetics of deposition. In order to identify the active species of the plasma, parameters such as gas flow, pressure and density of electric power were varied during titanium coating on glass substrate. By flowing argon gas of 10, 20, 30, 40 and 50 sccm (cubic centimeters per minute) for each gas flow a sequential scan of the electric current of 0.10, 0.20, 0.30, 0.40 , 0.50 A. The maximum value of 0.50 A was chosen based both on literature data and on limitations of the equipment. The monitoring of plasma species present during the deposition was carried out in situ by the technique of optical emission spectroscopy (OES) through the spectrometer Ocean Optics USB2000 Series. For this purpose, an apparatus was developed to adapt the OES inside the plasma reactor to stay positioned closest to the target. The radiations emitted by the species were detected by an optical fiber placed behind the glass substrate and their intensities as a function of wavelength were, displayed on a monitor screen. The acquisition time for each condition of the plain parameters was related to the minima of spectral lines intensities due to the film formed on the substrate. The intensities of different emission lines of argon and titanium were then analyzed as a function of time, to determine the active species and estimate the thickness of the deposited films. After the deposition, the coated glasses thin films were characterized by optical transmittance through an infrared laser. It was found that the thickness and deposition rate determined by in situ analysis were consistent with the results obtained by laser transmittance

Estudo do processo de combustão in-situ usando poços horizontais como produtores de óleo (Toe-to-Hell Air Injection)

The method "toe-to-heel air injection" (THAITM) is a process of enhanced oil recovery, which is the integration of in-situ combustion with technological advances in drilling horizontal wells. This method uses horizontal wells as producers of oil, keeping vertical injection wells to inject air. This process has not yet been applied in Brazil, making it necessary, evaluation of these new technologies applied to local realities, therefore, this study aimed to perform a parametric study of the combustion process with in-situ oil production in horizontal wells, using a semi synthetic reservoir, with characteristics of the Brazilian Northeast basin. The simulations were performed in a commercial software "STARS" (Steam, Thermal, and Advanced Processes Reservoir Simulator), from CMG (Computer Modelling Group). The following operating parameters were analyzed: air rate, configuration of producer wells and oxygen concentration. A sensitivity study on cumulative oil (Np) was performed with the technique of experimental design, with a mixed model of two and three levels (32x22), a total of 36 runs. Also, it was done a technical economic estimative for each model of fluid. The results showed that injection rate was the most influence parameter on oil recovery, for both studied models, well arrangement depends on fluid model, and oxygen concentration favors recovery oil. The process can be profitable depends on air rate

Estudo do processo de combustão in-situ em reservatórios maduros de óleos médios e leves (high pressure air injection)

Nearly 3 x 1011 m3 of medium and light oils will remain in reservoirs worldwide after conventional recovery methods have been exhausted and much of this volume would be recovered by Enhanced Oil Recovery (EOR) methods. The in-situ combustion (ISC) is an EOR method in which an oxygen-containing gas is injected into a reservoir where it reacts with the crude oil to create a high-temperature combustion front that is propagated through the reservoir. The High Pressure Air Injection (HPAI) method is a particular denomination of the air injection process applied in light oil reservoirs, for which the combustion reactions are dominant between 150 and 300°C and the generation of flue gas is the main factor to the oil displacement. A simulation model of a homogeneous reservoir was built to study, which was initially undergone to primary production, for 3 years, next by a waterflooding process for 21 more years. At this point, with the mature condition established into the reservoir, three variations of this model were selected, according to the recovery factors (RF) reached, for study the in-situ combustion (HPAI) technique. Next to this, a sensitivity analysis on the RF of characteristic operational parameters of the method was carried out: air injection rate per well, oxygen concentration into the injected gas, patterns of air injection and wells perforations configuration. This analysis, for 10 more years of production time, was performed with assistance of the central composite design. The reservoir behavior and the impacts of chemical reactions parameters and of reservoir particularities on the RF were also evaluated. An economic analysis and a study to maximize the RF of the process were also carried out. The simulation runs were performed in the simulator of thermal processes in reservoirs STARS (Steam, Thermal, and Advanced Processes Reservoir Simulator) from CMG (Computer Modelling Group). The results showed the incremental RF were small and the net present value (NPV) is affected by high initial investments to compress the air. It was noticed that the adoption of high oxygen concentration into the injected gas and of the five spot pattern tends to improve the RF, and the wells perforations configuration has more influence with the increase of the oil thickness. Simulated cases relating to the reservoir particularities showed that smaller residual oil saturations to gas lead to greater RF and the presence of heterogeneities results in important variations on the RF and on the production curves

Estudo dos parâmetros operacionais do processo de combustão in situ em reservatório de petróleo pesado

The occurrence of heavy oil reservoirs have increased substantially and, due to the high viscosity characteristic of this type of oil, conventional recovery methods can not be applied. Thermal methods have been studied for the recovery of this type of oil, with a main objective to reduce its viscosity, by increasing the reservoir temperature, favoring the mobility of the oil and allowing an increasing in the productivity rate of the fields. In situ combustion (ISC) is a thermal recovery method in which heat is produced inside the reservoir by the combustion of part of the oil with injected oxygen, contrasting with the injection of fluid that is heated in the surface for subsequent injection, which leads to loss heat during the trajectory to the reservoir. The ISC is a favorable method for recovery of heavy oil, but it is still difficult to be field implemented. This work had as an objective the parametric analysis of ISC process applied to a semi-synthetic reservoir with characteristics of the Brazilian Northeast reservoirs using vertical production and vertical injection wells, as the air flow injection and the wells completions. For the analysis, was used a commercial program for simulation of oil reservoirs using thermal processes, called Steam, Thermal and Advanced Processes Reservoir Simulator (STARS) from Computer Modelling Group (CMG). From the results it was possible to analyze the efficiency of the ISC process in heavy oil reservoirs by increasing the reservoir temperature, providing a large decrease in oil viscosity, increasing its mobility inside the reservoir, as well as the improvement in the quality of this oil and therefore increasing significantly its recovered fraction. Among the analyzed parameters, the flow rate of air injection was the one which had greater influence in ISC, obtaining higher recovery factor the higher is the flow rate of injection, due to the greater amount of oxygen while ensuring the maintenance of the combustion front

Avaliação de diferentes formas de preservação e desenvolvimento in situ de folículos ovarianos pré-antrais caprinos

This study evaluated the effect of indole-3-acetic acid (IAA) in the activation of goats preantral follicles (FOPA). Were used four pairs of ovaries of adult mixed breed goats. Each ovarian pair was divided into 23 fragments. One fragment was fixed for histology and other fragment was using to follicular isolation procedure. The remaining fragments were cultured in 1.0 ml of Minimum Essential Medium (MEM) or MEM supplemented with IAA at concentrations of 10, 40, 100, 500 or 1000 ng/mL. The in vitro culture was performed at 39°C in incubator with 5% CO2 for 1, 3 and 5 days. After in vitro culture was evaluated histological integrity and viability of FOPA. The addition of 100 ng/ml of IAA to MEM showed a significant increase in follicles transition in the third day of in vitro culture, characterizing follicular activation. Moreover, this concentration was obtained maintaining the histological integrity of PAF by the fifth day of in vitro culture. The viability test confirmed the results of histology. Thus, we conclude that IAA can promote the activation of goats FOPA

Extração enzimática de óleo e produção in situ de biodiesel a partir da Moringa oleífera Lam

With the growth and development of modern society, arises the need to search for new raw materials and new technologies which present the "clean" characteristic, and do not harm the environment, but can join the energy needs of industry and transportation. The Moringa oleifera Lam, plant originating from India, and currently present in the Brazilian Northeast, presents itself as a multi-purpose plant, can be used as a coagulant in water treatment, as a natural remedy and as a feedstock for biodiesel production. In this work, Moringa has been used as a raw material for studies on the extraction and subsequently in the synthesis of biodiesel. Studies have been conducted on various techniques of Moringa oil extraction (solvents, mechanical pressing and enzymatic), being specially developed an experimental design for the aqueous extraction with the aid of the enzyme Neutrase© 0.8 L, with the aim of analyzing the influence variable pH (5.5-7.5), temperature (45-55°C), time (16-24 hours) and amount of catalyst (2-5%) on the extraction yield. In relation to study of the synthesis of biodiesel was initially carried out a conventional transesterification (50°C, KOH as a catalyst, methanol and 60 minutes reaction). Next, a study was conducted using the technique of in situ transesterification by using an experimental design variables as temperature (30-60°C), catalyst amount (2-5%), and molar ratio oil / ethanol (1:420-1:600). The extraction technique that achieved the highest extraction yield (35%) was the one that used hexane as a solvent. The extraction using 32% ethanol obtained by mechanical pressing and extraction reached 25% yield. For the enzymatic extraction, the experimental design indicated that the extraction yield was most affected by the effect of the combination of temperature and time. The maximum yield obtained in this extraction was 16%. After the step of obtaining the oil was accomplished the synthesis of biodiesel by the conventional method and the in situ technique. The method of conventional transesterification was obtained a content of 100% and esters by in situ technique was also obtained in 100% in the experimental point 7, with a molar ratio oil / alcohol 1:420, Temperature 60°C in 5% weight KOH with the reaction time of 1.5 h. By the experimental design, it was found that the variable that most influenced the ester content was late the percentage of catalyst. By physico-chemical analysis it was observed that the biodiesel produced by the in situ method fell within the rules of the ANP, therefore this technique feasible, because does not require the preliminary stage of oil extraction and achieves high levels of esters

Avaliação da produção de biodiesel de microalga Isochrysis galbana via transesterificação in situ

Microalgae are microscopic photosynthetic organisms that grow rapidly and in different environmental conditions due to their simple cellular structure. The cultivation of microalgae is a biological system capable of storing solar energy through the production of organic compounds via photosynthesis, and these species presents growth faster than land plants, enabling higher biomass yield. Thus, it is understood that the cultivation of these photosynthetic mechanisms is part of a relevant proposal, since, when compared to other oil producing raw materials, they have a significantly higher productivity, thus being a raw material able to complete the current demand by biodiesel . The overall aim of the thesis was to obtain biofuel via transesterification process of bio oil from the microalgae Isochrysis galbana. The specific objective was to estimate the use of a photobioreactor at the laboratory level, for the experiments of microalgae growth; evaluating the characteristics of biodiesel from microalgae produced by in situ transesterification process; studying a new route for disinfection of microalgae cultivation, through the use of the chemical agent sodium hypochlorite. The introduction of this new method allowed obtaining the kinetics of the photobioreactor for cultivation, besides getting the biomass needed for processing and analysis of experiments in obtaining biodiesel. The research showed acceptable results for the characteristics observed in the bio oil obtained, which fell within the standards of ANP Resolution No. 14, dated 11.5.2012 - 18.5.2012. Furthermore, it was demonstrated that the photobioreactor designed meet expectations about study culture growth and has contributed largely to the development of the chosen species of microalgae. Thus, it can be seen that the microalgae Isochrysis galbana showed a species with potential for biodiesel production

Caracterização in situ e diversidade genética de algodoeiros mocós (Gossypium hissutum raça marie galante) da Região Nordeste do Brasil

Brazil is one of the major centers of diversity for polyploid cotton plants; these plants belong to the genus Gossypium, which has three known species: G. hirsutum, G. barbadense and G. mustelinum. The Northeast is the only region where the three species occur, the last group being endemic. Northeast s cotton plants can be important sources of variability for genetic breeding. It is believed that great part of local diversity is being lost, due to economic, political, cultural and agricultural problems. In an attempt to mitigate this loss and delineate conservation strategies it is necessary to know how the species are found where they occur. The objective was to characterize and determine how plants are maintained in situ in the states of Maranhão, Piauí, Ceará, Rio Grande do Norte and Paraíba at the beginning of the XXI century. The in situ characterization of G. hirsutum and G. barbadense was conducted through structured interviews with the cotton plants owners and through the analysis of the environment. The data were collected during expeditions undertaken between the years 2004 to 2005. Twenty-two plants were collected in the state of Paraíba, forty-four in the state of Rio Grande do Norte, one hundred and forty-six in the state of Ceará, forty in the state of Maranhão and ninety-one plants in the state of Piauí. All plants collected in the states of Paraíba and Rio Grande do Norte belonged to moco type. Moco cotton plants also predominated in the other states, representing 92%, 62% and 78% of plants collected in Ceará, Piauí and Maranhão, respectively. The other cotton plants collected belong to the species G. barbadense. The cotton plants were found in situ as dooryard plants, roads side, feral populations, cultivation or local varieties. Great part were dooryard plants (45.2%), being major in Piauí and Maranhão. Cultivation predominated in Ceará; in Rio Grande do Norte feral populations were the most frequent and, in Paraíba, local varieties. The maintenance of moco plants is related, mainly, to the phytotherapic domestic use (20.9%) and to confection of lamp wicks (29.7%). Few inhabitants in Paraíba, Rio Grande do Norte, Piauí and none in Maranhão used harvest the plants, storage the seeds or gin; however, in Ceará, 40.5% of owners affirmed that they harvested and commercialized the fiber. It was found that the maintenance of species is dependent of the fragile cultural habits of local inhabitants, therefore the maintenance in situ is not a suitable way to conservation of genetic resources. The efforts must be directed to the continuity of collections, maintenance and characterization ex situ

caracterização in situ e estrutura genética de populações de Gossypium mustelinum

Gossypium mustelinum Miers ex Watt is the only cotton species native from Brazil. It is endemic of the semi-arid region from North-east of the country, where it occur near from resilient water sources. The threats to the in situ conservation of the populations are caused by human interference in its habitat, mainly by excessive cattle graze and deforestation. Establish efficient strategies of in situ conservation depend on the accomplishment of a diagnosis of how the specie is found in its natural environment, and the knowledge about the genetic structure of the populations. The objectives of this work were i) to determine the in situ conditions of two populations present in rivers from basin of Rio Paraguaçu at the Bahia State, ii) to evaluate the structure and genetic variability presented in both populations, iii) to establish in situ and ex situ conservation strategies. It were realized collection in november 2007, when was realized in situ characterization of G. mustelinum. SSR markers were used for analyze 218 genotypes deriving from two populations of the G. mustelinum, localized at Tocó river and the Capivara river. The allelic frequencies, the heterozigosity and the F statics were estimated. All the plants were classified as wild and natives, and there was no evidence of the use the plants or its parts. The populations showed different conservation conditions in situ. Few plantlets were found in sites with excessive cattle feed, an indication that the damages in young plants should be high enough to compromise the renovation of the populations. On the other hand, populations were well preserved when the anthropic damages was low or inexistent. The 14 SSR primer pairs amplified 17 loci with a medium number of 5 alleles per locus (a total of 85 alleles). The high level of endogamy estimated (FIS=0,808) and the low observed heterozygosity (H0=0,093) were indicatives that the populations reproduce mainly by selfing, geitonogamy and crosses between related individuals. The genetic diversity was high (HE=0,482) and the differentiation between the populations was very high (FST=0,328). At least two sites from both populations of G. mustelinum must be preserved to achieve suitable in situ conservation. Actions that preserve the gallery forest and keep the cattle away should implemented, and could be as simple as erecting a fence. It is not possible anticipated if the in situ preservation will be possible. Therefore collections and ex situ preservation of representative specimens are essential to conserve the genetic diversity of native G. mustelinum

Caracterização genética e in situ de Gossypium barbadense na região norte do Brasil

Brazil has been considered one of the diversity centers of Gossypium barbadense species. It is believed that a relatively big erosion genetic process occurs with the species, due to economic, cultural and agricultural problems. A local diagnostic about species situation is the first step for reducing the diversity loss and establishing conservation strategies in situ. This research aimed the identification of the presence of Gossypium populations, characterization, determination of the main risks and collection of the accesses to store in germoplam banks, in Para and Amapa States. Expeditions were conducted in November 2004. An interview was carried out with the plant proprietor for characterizing in situ of G. barbadense species and of the environment where the plants were inserted. On hundred seventy nine plants in 22 municipal districts were collected in Para State and 117 plants in nine municipal districts in Amapa State. The majority of plants belong to G. barbadense species (98% in Amapa and 94% in Para). Plants occur in back yards, beside roads and spontaneously. That ones from back yards were more abundant (97% in Amapa and 95% in Para) and maintained as medicinal plants as the principal reason. Plants in natural environments in both states evaluated were not found, therefore, the creation of reserves and the application of others conventional methods of maintenance in situ are not applicable. The plant proprietors do not use to store or process seeds. Seed storage was reported as a practice by only 1% of the plant proprietors from Para and 11% from Amapa. The most plants collected were from two to three years of age (58% in Amapa and 93% in Para). As conclusions G. barbadense is the species most spread in the two studied states and are found in back yards. In Amapa State the botanical variety barbadense or Quebradinho is predominant, whereas in Para State the predominant variety is brasiliense or Rim-de-boi. Adequate conservation of thestudied species must be carried out in germoplasm collections maintained ex situ

Reforma a vapor catalítica do metano: Otimização da produção e seletividade em hidrogênio por absorção in situ do CO2 produzido

Topics of research related to energy and environment have significantly grown in recent years, with the need of its own energy as hydrogen. More particularly, numerous researches have been focused on hydrogen as energy vector. The main portion of hydrogen is presently obtained by reforming of methane or light hydrocarbons (steam, oxy, dry or auto reforming). During the methane steam reforming process the formation of CO2 undesirable (the main contributor to the greenhouse effect) is observed. Thus, an oxide material (sorbent) can be used to capture the CO2 generated during the process and simultaneously shifting the equilibrium of water gas shift towards thermodynamically more favorable production of pure hydrogen. The aim of this study is to develop a material with dual function (catalyst/sorbent) in the reaction of steam reforming of methane. CaO is well known as CO2 sorbent due to its high efficiency in reactions of carbonation and easy regeneration through calcination. However the kinetic of carbonation decreases quickly with time and carbonation/calcination cycles. A calcium aluminate (Ca12Al14O33) should be used to avoid sintering and increase the stability of CaO sorbents for several cycles. Nickel, the industrial catalyst choice for steam reforming has been added to the support from different manners. These bi-functional materials (sorbent/catalyst) in different molar ratios CaO.Ca12Al14O33 (48:52, 65:35, 75:25, 90:10) were prepared by different synthesis methodologies, among them, especially the method of microwave assisted self-combustion. Synthesis, structure and catalytic performances of Ni- CaO.Ca12Al14O33 synthesized by the novel method (microwave assisted selfcombustion) proposed in this work has not being reported yet in literature. The results indicate that CO2 capture time depends both on the CaO excess and on operating conditions (eg., temperature and H2O/CH4 ratio). To be efficient for CO2 sorption, temperature of steam reforming needs to be lower than 700 °C. An optimized percentage corresponding to 75% of CaO and a ratio H2O/CH4 = 1 provides the most promising results since a smaller amount of water avoids competition between water and CO2 to form carbonate and hydroxide. If this competition is most effective (H2O/CH4 = 3) and would have a smaller amount of CaO available for absorption possibly due to the formation of Ca(OH)2. Therefore, the capture time was higher (16h) for the ratio H2O/CH4 = 1 than H2O/CH4 = 3 (7h) using as catalyst one prepared by impregnating the support obtained by microwave assisted self-combustion. Therefore, it was demonstrated that, with these catalysts, the CO2 sorption on CaO modifies the balance of the water gas-shift reaction. Consequently, steam reforming of CH4 is optimized, producing pure H2, complete conversion of methane and negligible concentration of CO2 and CO during the time of capture even at low temperature (650 °C). This validates the concept of the sorption of CO2 together with methane steam reforming