46 resultados para Função de correntropia cíclica
em Universidade Federal do Rio Grande do Norte(UFRN)
Resumo:
Information extraction is a frequent and relevant problem in digital signal processing. In the past few years, different methods have been utilized for the parameterization of signals and the achievement of efficient descriptors. When the signals possess statistical cyclostationary properties, the Cyclic Autocorrelation Function (CAF) and the Spectral Cyclic Density (SCD) can be used to extract second-order cyclostationary information. However, second-order cyclostationary information is poor in nongaussian signals, as the cyclostationary analysis in this case should comprise higher-order statistical information. This paper proposes a new mathematical tool for the higher-order cyclostationary analysis based on the correntropy function. Specifically, the cyclostationary analysis is revisited focusing on the information theory, while the Cyclic Correntropy Function (CCF) and Cyclic Correntropy Spectral Density (CCSD) are also defined. Besides, it is analytically proven that the CCF contains information regarding second- and higher-order cyclostationary moments, being a generalization of the CAF. The performance of the aforementioned new functions in the extraction of higher-order cyclostationary characteristics is analyzed in a wireless communication system where nongaussian noise exists.
Resumo:
To enhance the maintenance practices, Oil and Gas Pipelines are inspected from the inside by automated systems called PIG (Pipeline Inspection Gauge). The inspection and mapping of defects, as dents and holes, in the internal wall of these pipelines are increasingly put into service toward an overall Structural Integrity Policy. The residual life of these structures must be determined such that minimize its probability of failure. For this reason, the investigation on the detection limits of some basic topological features constituted by peaks or valleys disposed along a smooth surface is of great value for determining the sensitivity of the measurements of defects from some combinations of circumferential, axial and radial extent. In this investigation, it was analyzed an inductive profilometric sensor to scan three races, radius r1, r2, r3, in a circular surface of low carbon steel, equipped with eight consecutive defects simulated by bulges and holes by orbit, equally spaced at p/4 rad. A test rig and a methodology for testing in laboratory were developed to evaluate the sensor response and identify their dead zones and jumps due to fluctuations as a function of topological features and scanning velocity, four speeds different. The results are presented, analyzed and suggestions are made toward a new conception of sensor topologies, more sensible to detect these type of damage morphologies
Resumo:
This present work uses a generalized similarity measure called correntropy to develop a new method to estimate a linear relation between variables given their samples. Towards this goal, the concept of correntropy is extended from two variables to any two vectors (even with different dimensions) using a statistical framework. With this multidimensionals extensions of Correntropy the regression problem can be formulated in a different manner by seeking the hyperplane that has maximum probability density with the target data. Experiments show that the new algorithm has a nice fixed point update for the parameters and robust performs in the presence of outlier noise.
Resumo:
The great interest in nonlinear system identification is mainly due to the fact that a large amount of real systems are complex and need to have their nonlinearities considered so that their models can be successfully used in applications of control, prediction, inference, among others. This work evaluates the application of Fuzzy Wavelet Neural Networks (FWNN) to identify nonlinear dynamical systems subjected to noise and outliers. Generally, these elements cause negative effects on the identification procedure, resulting in erroneous interpretations regarding the dynamical behavior of the system. The FWNN combines in a single structure the ability to deal with uncertainties of fuzzy logic, the multiresolution characteristics of wavelet theory and learning and generalization abilities of the artificial neural networks. Usually, the learning procedure of these neural networks is realized by a gradient based method, which uses the mean squared error as its cost function. This work proposes the replacement of this traditional function by an Information Theoretic Learning similarity measure, called correntropy. With the use of this similarity measure, higher order statistics can be considered during the FWNN training process. For this reason, this measure is more suitable for non-Gaussian error distributions and makes the training less sensitive to the presence of outliers. In order to evaluate this replacement, FWNN models are obtained in two identification case studies: a real nonlinear system, consisting of a multisection tank, and a simulated system based on a model of the human knee joint. The results demonstrate that the application of correntropy as the error backpropagation algorithm cost function makes the identification procedure using FWNN models more robust to outliers. However, this is only achieved if the gaussian kernel width of correntropy is properly adjusted.
Resumo:
Os primatas não humanos, como Callithrix jacchus vêm sendo utilizados com maior frequência em pesquisa biomédica e, recentemente, nosso laboratório propôs uma nova classificação para monitorar com mais detalhes as modificações comportamentais e hormonais relacionadas ao desenvolvimento. O presente trabalho monitorou os níveis de hormônios gonadais de 4 machos e 6 fêmeas de C. jacchus durante as fases juvenil I e II e subadulta (dos 5 aos 15 meses). Os resultados apontaram que os níveis de progesterona nas fêmeas e andrógenas nos machos foram estatisticamente mais elevados nos estágios juvenil II e subadulto, respectivamente, em relação ao estágio juvenil I. Estes achados indicam que, de acordo com a nova classificação, foi possível observar que o funcionamento gonadal se instala mais cedo nas fêmeas
Resumo:
This work has as its theme the social function of terrenos de marinha. Theresearch universe is the terrenos de marinha of Natal coastline, focusing on thefulfillment of its social function. Prescribed by law since the colonial period with thepurpose of protecting the coast and free movement of people and goods, theywere swathes of land not available to private use by individuals. With the transitionfrom the allotments system to the purchase and sale, regard to land access,crystallized with the creation of the Land Law in the nineteenth century, the land isheld as merchandise and terrenos de marinha, following this logic, also acquireexchange value and become capable of enjoyment by private individuals, with thecondition of tax payments to the state. This is seen until the twentieth century,when in 1988, primarily because of the Federal Constitution promulgation, begins anew cycle when is possible to use on terrenos de marinha the principle of thesocial function of property. From this perspective this study aims to identify thesocial function of terrenos de marinha in Natal, focusing on the public destinationand the use value of the city coastline. To this end, it was made a data collection inthe on-line information system of the Federal Heritage Department of Rio Grandedo Norte (SPU / RN) and in the terrenos de marinha areas, in order to find out ifthey had public or private use, or if they were empty lots, as well as if thepopulation access to the shore exist. Interviews with managers of the SPU weremade. The empirical study showed that the social function of terrenos de marinhain the city of Natal still didn´t happen, considering the constant existence of vacantlots in their areas, the lack of access in significant portions of the coastline and thereduced areas directed to common use along the coastline, minimizing its potentialof enjoyment by the population. It concludes by pointing to the existence of a newtransition phase on the terrenos de marinha, in witch, gradually, come up lawprovisions in the legal system and public policies to expand the purely taxcollection function attributed to this land for two centuries. In this direction, thesocial function of terrenos de marinha is embodied in concomitant adjustment ofthe tax collection function and the rescue of coastline use value, national heritageand a place for sociability and social relations development
Resumo:
Oil wells subjected to cyclic steam injection present important challenges for the development of well cementing systems, mainly due to tensile stresses caused by thermal gradients during its useful life. Cement sheath failures in wells using conventional high compressive strength systems lead to the use of cement systems that are more flexible and/or ductile, with emphasis on Portland cement systems with latex addition. Recent research efforts have presented geopolymeric systems as alternatives. These cementing systems are based on alkaline activation of amorphous aluminosilicates such as metakaolin or fly ash and display advantageous properties such as high compressive strength, fast setting and thermal stability. Basic geopolymeric formulations can be found in the literature, which meet basic oil industry specifications such as rheology, compressive strength and thickening time. In this work, new geopolymeric formulations were developed, based on metakaolin, potassium silicate, potassium hydroxide, silica fume and mineral fiber, using the state of the art in chemical composition, mixture modeling and additivation to optimize the most relevant properties for oil well cementing. Starting from molar ratios considered ideal in the literature (SiO2/Al2O3 = 3.8 e K2O/Al2O3 = 1.0), a study of dry mixtures was performed,based on the compressive packing model, resulting in an optimal volume of 6% for the added solid material. This material (silica fume and mineral fiber) works both as an additional silica source (in the case of silica fume) and as mechanical reinforcement, especially in the case of mineral fiber, which incremented the tensile strength. The first triaxial mechanical study of this class of materials was performed. For comparison, a mechanical study of conventional latex-based cementing systems was also carried out. Regardless of differences in the failure mode (brittle for geopolymers, ductile for latex-based systems), the superior uniaxial compressive strength (37 MPa for the geopolymeric slurry P5 versus 18 MPa for the conventional slurry P2), similar triaxial behavior (friction angle 21° for P5 and P2) and lower stifness (in the elastic region 5.1 GPa for P5 versus 6.8 GPa for P2) of the geopolymeric systems allowed them to withstand a similar amount of mechanical energy (155 kJ/m3 for P5 versus 208 kJ/m3 for P2), noting that geopolymers work in the elastic regime, without the microcracking present in the case of latex-based systems. Therefore, the geopolymers studied on this work must be designed for application in the elastic region to avoid brittle failure. Finally, the tensile strength of geopolymers is originally poor (1.3 MPa for the geopolymeric slurry P3) due to its brittle structure. However, after additivation with mineral fiber, the tensile strength became equivalent to that of latex-based systems (2.3 MPa for P5 and 2.1 MPa for P2). The technical viability of conventional and proposed formulations was evaluated for the whole well life, including stresses due to cyclic steam injection. This analysis was performed using finite element-based simulation software. It was verified that conventional slurries are viable up to 204ºF (400ºC) and geopolymeric slurries are viable above 500ºF (260ºC)
Resumo:
This work reports the influence of the poly (ethylene terephthalate) textile surface modification by plasmas of O2 and mixtures (N2 + O2), on their physical and chemical properties. The treatment was carried out in a vacuum chamber. Some parameters remained constant during all treatment, such as: Voltage 470 V; Pressure 1,250 Mbar; Current: 0, 10 A and gas flow: 10 cm3/min. Other parameters, such as working gas composition and treatment time, were modified as the following: to the O2 plasma modified samples only the treatment time was changed (10, 20, 30, 40, 50 and 60 minutes). To the plasma with O2 and N2 only the chemical concentrations were changed. Through Capillary tests (vertical) an increase in textile wettability was observed as well as its influence on aging time and its consequence on wettability. The surface functional groups created after plasma treatments were investigated using X-ray Photoelectron Spectroscopy (XPS). The surface topography was examined by scanning electron microscope (SEM)
Resumo:
In Brazilian Northeast there are reservoirs with heavy oil, which use steam flooding as a recovery method. This process allows to reduce oil viscosity, increasing its mobility and consequently its oil recovery. Steam injection is a thermal method and can occurs in continues or cyclic form. Cyclic steam stimulation (CSS) can be repeated several times. Each cycle consisting of three stages: steam injection, soaking time and production phase. CSS becomes less efficient with an increase of number of cycles. Thus, this work aims to study the influence of compositional models in cyclic steam injection and the effects of some parameters, such like: flow injection, steam quality and temperature of steam injected, analyzing the influence of pseudocomponents numbers on oil rate, cumulative oil, oil recovery and simulation time. In the situations analyzed was compared the model of fluid of three phases and three components known as Blackoil . Simulations were done using commercial software (CMG), it was analyzed a homogeneous reservoir with characteristics similar to those found in Brazilian Northeast. It was observed that an increase of components number, increase the time spent in simulation. As for analyzed parameters, it appears that the steam rate, and steam quality has influence on cumulative oil and oil recovery. The number of components did not a lot influenced on oil recovery, however it has influenced on gas production
Resumo:
In this work, spoke about the importance of image compression for the industry, it is known that processing and image storage is always a challenge in petrobrás to optimize the storage time and store a maximum number of images and data. We present an interactive system for processing and storing images in the wavelet domain and an interface for digital image processing. The proposal is based on the Peano function and wavelet transform in 1D. The storage system aims to optimize the computational space, both for storage and for transmission of images. Being necessary to the application of the Peano function to linearize the images and the 1D wavelet transform to decompose it. These applications allow you to extract relevant information for the storage of an image with a lower computational cost and with a very small margin of error when comparing the images, original and processed, ie, there is little loss of quality when applying the processing system presented . The results obtained from the information extracted from the images are displayed in a graphical interface. It is through the graphical user interface that the user uses the files to view and analyze the results of the programs directly on the computer screen without the worry of dealing with the source code. The graphical user interface, programs for image processing via Peano Function and Wavelet Transform 1D, were developed in Java language, allowing a direct exchange of information between them and the user
Resumo:
Steam injection is a method usually applied to very viscous oils and consists of injecting heat to reduce the viscosity and, therefore, increase the oil mobility, improving the oil production. For designing a steam injection project it is necessary to have a reservoir simulation in order to define the various parameters necessary for an efficient heat reservoir management, and with this, improve the recovery factor of the reservoir. The purpose of this work is to show the influence of the coupled wellbore/reservoir on the thermal simulation of reservoirs under cyclic steam stimulation. In this study, the methodology used in the solution of the problem involved the development of a wellbore model for the integration of steam flow model in injection wellbores, VapMec, and a blackoil reservoir model for the injection of cyclic steam in oil reservoirs. Thus, case studies were developed for shallow and deep reservoirs, whereas the usual configurations of injector well existing in the oil industry, i.e., conventional tubing without packer, conventional tubing with packer and insulated tubing with packer. A comparative study of the injection and production parameters was performed, always considering the same operational conditions, for the two simulation models, non-coupled and a coupled model. It was observed that the results are very similar for the specified well injection rate, whereas significant differences for the specified well pressure. Finally, on the basis of computational experiments, it was concluded that the influence of the coupled wellbore/reservoir in thermal simulations using cyclic steam injection as an enhanced oil recovery method is greater for the specified well pressure, while for the specified well injection rate, the steam flow model for the injector well and the reservoir may be simulated in a non- coupled way
Resumo:
A Síndrome de Berardinelli-Seip ou Lipodistrofia Generalizada Congênita (LGC) é uma doença rara, com transmissão autossômica recessiva, caracterizada principalmente pela ausência quase total de tecido adiposo. Os pacientes afetados apresentam resistência a insulina, dislipidemia e hipertensão arterial. Estudos têm evidenciado que estas alterações metabólicas interferem na modulação autonômica para o nó sinusal. O principal objetivo deste estudo foi investigar a modulação autonômica em pacientes portadores de LGC, através da variabilidade de freqüência cardíaca (VFC), pelo método linear de domínio de tempo na Eletrocardiografia Dinâmica de 24 horas e estabelecer um critério relativamente simples, não invasivo, para diagnóstico de disfunção autonômica nestes pacientes. Participou voluntariamente deste estudo transversal, um grupo de pacientes portadores de LGC (n=18) na faixa etária de 9,3 a 39,8 anos (21,3 ± 8,3) cuja variabilidade de freqüência cardíaca foi comparada com um grupo de pacientes controles (n=19) com idade de 9,3 a 39,1 anos (21,4 ± 7,8). Todos os voluntários foram submetidos à avaliação clínica, laboratorial, antropométrica e análise de VFC no domínio de tempo através de eletrocardiografia dinâmica de 24 horas. Para análise dos dados relativos aos índices temporais de VFC foram utilizados o MeanRR, SSDN e rMSSD. Pacientes com LGC apresentavam aumento da pressão arterial comparados com indivíduos do grupo controle (sistólica, 131,1 vs 106,3 mmHg, p<0,05); diastólica, 85,0 vs 68,2 mmHg, p<0,05) e 10 tinham critérios para diagnóstico de Hipertensão Arterial e Hipertrofia do Ventrículo Esquerdo. Os níveis de glicose, triglicerídeos, colesterol e HOMA-R eram elevados e 12 pacientes tinham critérios para diabetes mellitus tipo 2. Comparado com os controles, pacientes com LGC tinham diminuição dos índices MeanRR (639,8 vs 780,5 ms, p<0,001), SDNN (79,2 vs 168,5 ms, p<0,001), e rMSSD (15,8 vs 59,6 ms, p<0,001). Em pacientes com LGC, a redução da VFC foi independente de distúrbios metabólicos e hemodinâmicos. Os resultados de nosso experimento indicam que pacientes com LGC apresentavam modulação autonômica anormal caracterizada pelo aumento da freqüência cardíaca e pronunciada redução da VFC, independente de distúrbios metabólicos e hemodinâmicos observados nesta síndrome. O caráter multidisciplinar desse estudo fica contemplado pela interação de profissionais de diversas áreas como: cardiologia, endocrinologia, metabolismo, neurologia, nutrição, etc
Resumo:
Este estudo teve por objetivo avaliar os fatores associados à disfunção sexual em mulheres de meia idade. Realizou-se um estudo descritivo transversal, que compreendeu 370 mulheres, entre 40 a 65 anos, atendidas nas Unidades Básicas de Saúde de cada distrito sanitário (Norte, Sul, Leste e Oeste) da cidade de Natal, no estado do Rio Grande do Norte, Brasil. Para avaliar a função sexual utilizou-se o Female Sexual Function Index (FSFI). A sintomatologia climatérica foi avaliada por meio do Menopause Rating Scale (MRS). O Índice de Blatt-Kupperman (IMBK) foi utilizado para avaliação quantitativa global da ocorrência de sintomas/queixas. A atividade física foi avaliada pelo questionário International Physical Activity Questionnaire - IPAQ (versão curta). A avaliação da qualidade de vida geral se deu pelo WHOQOL-Bref. A análise estatística foi realizada utilizando o programa estatístico MINITAB version16. Além de análises descritivas das variáveis categorizadas, utilizou-se o teste qui-quadrado de Person com o intuito de verificar possíveis associações entre as variáveis sociodemográficas, comportamentais, clínicas, níveis de atividade física, sintomatologia climatérica, qualidade de vida e a função sexual das mulheres estudadas. Desenvolveu-se a regressão logística para verificar a influência dessas variáveis sobre a disfunção sexual. Considerou-se o nível de significância de 5% para todos os testes. Os resultados mostraram que a média de idade das mulheres estudadas foi de 49,8 (±8,1) anos. Do total dessas mulheres, 67% apresentaram disfunção sexual. Observou-se que 54,5% delas se encontravam na pré-menopausa. Avaliando a influência das variáveis sobre a função sexual; faixa etária (56-65) (p<0,001), estado civil (divorciada/separada) (p < 0,001), escolaridade (baixa) (p=0,017), menopausa (p < 0,001), histerectomia (p = 0,016), nível de atividade física (sedentária) (p=0,002), sintomas do climatério (forte) (p<0,001) e qualidade de vida (baixa) (p<0,001), estiveram associados à disfunção sexual em mulheres de meia idade. Concluiu-se neste estudo que fatores sociodemográficos, clínicos, comportamentais, níveis de atividade física, sintomatologia climatérica e qualidade de vida influenciam significativamente a função sexual na mulher de meia idade
Efeitos da deficiência de vitamina A na função pulmonar de crianças após infecção respiratória viral
Resumo:
Conselho Nacional de Desenvolvimento Científico e Tecnológico
Resumo:
This study investigated the influence of partial colectomy associated with hepatectomy on the biodistribution of the 99mTc-phytate, on metabolic parameters, as well as labeling and morphology of red blood cells. Wistar rats were distributed into three groups (each with 6), nominated as colectomy, colectomy+hepatectomy and sham. In the 30th postoperative day all rats were injected with 99mTc-phytate 0.1mL i.v. (radioactivity 0.66 MBq). After 15 minutes, liver sample was harvested and weighed. Percentage radioactivity per gram of tissue (%ATI/g) was determined using an automatic gamma-counter. Serum AST, ALT, alkaline phosphatase and red blood cells labeling were determined. The liver %ATI/g and red blood cells labeling were lower in colectomy and colectomy+hepatectomy rats than in sham rats (p <0.05), and no difference was detected comparing the colectomy and colectomy+hepatectomy groups. Red blood cells morphology did not differ among groups. Serum levels of AST, ALT and alkaline fosfatase were significantly higher in colectomy+hepatectomy than in colectomy rats (p<0.001). Hepatectomy associated with colectomy lowered the uptake of radiopharmaceutical in liver and in red blood cells in rats, coinciding with changes in liver enzymatic activity