100 resultados para Efeitos Ionosféricos de Ordem Superior
em Universidade Federal do Rio Grande do Norte(UFRN)
Resumo:
This work presents a theoretical and numerical analysis using the transverse resonance technique (TRT) and a proposed MTRT applied in the analysis of the dispersive characteristics of microstrip lines built on truncated isotropic and anisotropic dielectric substrates. The TRT uses the transmission lines model in the transversal section of the structure, allowing to analyze its dispersive behavior. The difference between TRT and MTRT consists basically of the resonance direction. While in the TRT the resonance is calculated in the same direction of the metallic strip normal axis, the MTRT considers the resonance in the metallic strip parallel plane. Although the application of the MTRT results in a more complex equivalent circuit, its use allows some added characterization, like longitudinal section electric mode (LSE) and longitudinal section magnetic mode (LSM), microstrips with truncated substrate, or structures with different dielectric regions. A computer program using TRT and MTRT proposed in this work is implemented for the characterization of microstrips on truncated isotropic and anisotropic substrates. In this analysis, propagating and evanescent modes are considered. Thus, it is possible to characterize both the dominant and higher order modes of the structure. Numerical results are presented for the effective permittivity, characteristic impedance and relative phase velocity for microstrip lines with different parameters and dimensions of the dielectric substrate. Agreement with the results obtained in the literature are shown, as well as experimental results. In some cases, the convergence analysis is also performed by considering the limiting conditions, like particular cases of isotropic materials or structures with dielectric of infinite size found in the literature. The numerical convergence of the formulation is also analyzed. Finally, conclusions and suggestions for the continuity of this work are presented
Resumo:
This work consists of the conception, developing and implementation of a Computational Routine CAE which has algorithms suitable for the tension and deformation analysis. The system was integrated to an academic software named as OrtoCAD. The expansion algorithms for the interface CAE genereated by this work were developed in FORTRAN with the objective of increase the applications of two former works of PPGEM-UFRN: project and fabrication of a Electromechanincal reader and Software OrtoCAD. The software OrtoCAD is an interface that, orinally, includes the visualization of prothetic cartridges from the data obtained from a electromechanical reader (LEM). The LEM is basically a tridimensional scanner based on reverse engineering. First, the geometry of a residual limb (i.e., the remaining part of an amputee leg wherein the prothesis is fixed) is obtained from the data generated by LEM by the use of Reverse Engineering concepts. The proposed core FEA uses the Shell's Theory where a 2D surface is generated from a 3D piece form OrtoCAD. The shell's analysis program uses the well-known Finite Elements Method to describe the geometry and the behavior of the material. The program is based square-based Lagragean elements of nine nodes and displacement field of higher order to a better description of the tension field in the thickness. As a result, the new FEA routine provide excellent advantages by providing new features to OrtoCAD: independency of high cost commercial softwares; new routines were added to the OrtoCAD library for more realistic problems by using criteria of fault engineering of composites materials; enhanced the performance of the FEA analysis by using a specific grid element for a higher number of nodes; and finally, it has the advantage of open-source project and offering customized intrinsic versatility and wide possibilities of editing and/or optimization that may be necessary in the future
Resumo:
The great interest in nonlinear system identification is mainly due to the fact that a large amount of real systems are complex and need to have their nonlinearities considered so that their models can be successfully used in applications of control, prediction, inference, among others. This work evaluates the application of Fuzzy Wavelet Neural Networks (FWNN) to identify nonlinear dynamical systems subjected to noise and outliers. Generally, these elements cause negative effects on the identification procedure, resulting in erroneous interpretations regarding the dynamical behavior of the system. The FWNN combines in a single structure the ability to deal with uncertainties of fuzzy logic, the multiresolution characteristics of wavelet theory and learning and generalization abilities of the artificial neural networks. Usually, the learning procedure of these neural networks is realized by a gradient based method, which uses the mean squared error as its cost function. This work proposes the replacement of this traditional function by an Information Theoretic Learning similarity measure, called correntropy. With the use of this similarity measure, higher order statistics can be considered during the FWNN training process. For this reason, this measure is more suitable for non-Gaussian error distributions and makes the training less sensitive to the presence of outliers. In order to evaluate this replacement, FWNN models are obtained in two identification case studies: a real nonlinear system, consisting of a multisection tank, and a simulated system based on a model of the human knee joint. The results demonstrate that the application of correntropy as the error backpropagation algorithm cost function makes the identification procedure using FWNN models more robust to outliers. However, this is only achieved if the gaussian kernel width of correntropy is properly adjusted.
Resumo:
Information extraction is a frequent and relevant problem in digital signal processing. In the past few years, different methods have been utilized for the parameterization of signals and the achievement of efficient descriptors. When the signals possess statistical cyclostationary properties, the Cyclic Autocorrelation Function (CAF) and the Spectral Cyclic Density (SCD) can be used to extract second-order cyclostationary information. However, second-order cyclostationary information is poor in nongaussian signals, as the cyclostationary analysis in this case should comprise higher-order statistical information. This paper proposes a new mathematical tool for the higher-order cyclostationary analysis based on the correntropy function. Specifically, the cyclostationary analysis is revisited focusing on the information theory, while the Cyclic Correntropy Function (CCF) and Cyclic Correntropy Spectral Density (CCSD) are also defined. Besides, it is analytically proven that the CCF contains information regarding second- and higher-order cyclostationary moments, being a generalization of the CAF. The performance of the aforementioned new functions in the extraction of higher-order cyclostationary characteristics is analyzed in a wireless communication system where nongaussian noise exists.
Resumo:
The study aims to investigate the limits of state intervention via induction on Economic Order, especially in cases regarding tax equality, through the analysis of their effects on economic development and on free competition from the perspective of economic efficiency and the Constitution. Thus, the work seeks to demonstrate that the achievement of equality in taxation is important in that it strengthens the economic relations in terms of efficiency, protects competition and fosters economic development to reduce regional and social inequalities and other constitutional desiderata. A dissertation is characterized by interdisciplinarity and was divided into two parts. The first is to discuss the legal meaning of equality from the doctrinal analysis of the principle and the relationship between equality and justice in the economic sense without rejecting its philosophical content. It is noteworthy that hermeneutics and the philosophy of language are useful tools for achieving equality in presenting the pragmatic methodologies applicable to the subject in terms of corrective justice. Based on these general assumptions, is going to study the tax equality and their characteristics, the corollary of the ability to pay and its relation to the economic capacity and the issue of progressivity in taxation as an ideal of distributive justice. The second part concerns the legal foundations of Economic Order and its relation to extrafiscality as a means of economic regulation in order to investigate the efficiency of this induction in order to promote economic development, free competition and tax equality itself to reduce inequalities and distributing wealth. Within this context, we investigated the scope of the constitutional principles of economic order, free enterprise and free competition, and favored differential treatment for small and medium enterprises, the issue of regional development for the reduction of regional and social inequalities, the problem the "fiscal war" and finally the efficiency from the perspective of Economic Analysis of Law
Resumo:
Coordenação de Aperfeiçoamento de Pessoal de Nível Superior
Resumo:
The major aim of this study was to test the hypothesis that the introduction of the Nile tilapia (Oreochromis niloticus) and the enrichment with nutrients (N and P) interact synergistically to change the structure of plankton communities, increase phytoplankton biomass and decrease water transparency of a semi-arid tropical reservoir. One field experiment was performed during five weeks in twenty enclosures (8m3) to where four treatments were randomly allocated: with tilapia addition (T), with nutrients addition (NP), with tilapia and nutrients addition (T+NP) and a control treatment with no tilapia or nutrients addition (C). A two-way repeated measures ANOVA was done to test for time (t), tilapia (T) and nutrient (NP) effects and their interaction on water transparency, total phosphorus, total nitrogen, phytoplankton and zooplankton. The results show that there was no effect of nutrient addition on these variables but significant fish effects on the biomass of total zooplankton, nauplii, rotifers, cladocerans and calanoid copepods, on the biovolume of Bacillariophyta, Zygnemaphyceae and large algae (GALD ≥ 50 μm) and on Secchi depth. In addition, we found significant interaction effects between tilapia and nutrients on Secchi depth and rotifers. Overall, tilapia decreased the biomass of most zooplankton taxa and large algae (diatoms) and decreased the water transparency while nutrient enrichment increased the biomass of zooplankton (rotifers) but only in the absence of tilapia. In conclusion, the influence of fish on the reservoir plankton community and water transparency was greater than that of nutrient loading. This finding suggests that biomanipulation should be a greater priority in the restoration of eutrophic reservoirs in tropical semi-arid regions
Resumo:
Top-down (grazing) and bottom-up (nutrient, light) controls are important in freshwater ecosystems regulation. Relative importance of these factors could change in space and time, but in tropical lakes bottom-up regulation has to been appointed as more influent. Present study aimed to test the hypothesis that phytoplankton growths rate in Armando Ribeiro reservoir, a huge eutrophic reservoir in semi-arid region of Rio Grande do Norte state, is more limited by nutrient available then zooplankton grazing pressure. Bioassay was conduced monthly from September (2008) to August (2009) manipulating two levels of nutrients (with/without addition) and two level of grazers (with/without removal). Experimental design was factorial 2X2 with four treatments (X5), (i) control with water and zooplankton from natural spot ( C ), (ii) with nutrient addition ( +NP ), (iii) with zooplankton remove ( -Z ) and (iv) with zooplankton remove and nutrient addition ( -Z+NP ). For bioassay confection transparent plastic bottles (500ml) was incubate for 4 or 5 days in two different depths, Secchi`s depth (high luminosity) and 3 times Secchi`s depth (low luminosity). Water samples were collected from each bottle in begins and after incubates period for chlorophyll a concentration analysis and zoopalnktonic organisms density. Phytoplankton growths rates were calculated. Bifactorial ANOVA was performance to test if had a significant effect (p<0,005) of nutrient addition and grazers remove as well a significant interaction between factors on phytoplankton growths rates. Effect magnitude was calculated the relative importance of each process. Results show that phytoplankton growth was in generally stimulated by nutrient addition, as while zooplankton remove rarely stimulated phytoplankton growth. Some significant interactions happening between nutrient additions and grazers remove on phytoplankton growth. In conclusion this study suggests that in studied reservoir phytoplankton growth is more controlled by ascendent factors than descendent
Resumo:
A 140,0 kDa lectin was purified and characterized from the mushroom Clavaria cristata. The purification procedures from the crude extract of the mushroom comprised gel filtration chromatography on Sephacryl s200 and ion exchange on Resource Q column. The purified lectin agglutinated all types of human erythrocytes with preference for trypsinized type O erythrocytes. The haemagglutinating activity is dependent of Ca 2+ ions and was strongly inhibited by the glycoprotein bovine submaxillary mucin (BSM) up to the concentration of 0, 125 mg/mL. The C. cristata lectin (CcL) was stable in the pH range of 2,5-11,5 and termostable up to 80 °C. CcL molecular mass determined by gel filtration on a Superose 6 10 300 column was approximately 140,3 kDa. SDS polyacrilamide gel electrophoresis revealed a single band with a molecular mass of approximately 14,5 kDa, when the lectin was heated at 100 ⁰C in the presence or absence of β-mercaptoethanol. CcL induced activation of murine peritoneal macrophages in vitro resulting in the release of nitric oxide (NO), reaching the maximum production at 24 h. In experimental paw oedema model in mice, CcL showed proinflammatory activity being able to induce oedema formation. Cell viability of HepG2, MDA 435 e 3T3 cell lines was examined after 72 h of incubation with CcL in different concentrations (0,5-50 μg/mL). CcL inhibited HepG2 cells growth with an IC50 value of 50 μg/mL. In the present work, the observed immunomodulatory and antiproliferative effects indicate CcL as a possible immunomodulator compound, interfering in the macrophages immune response, taking possible anti-parasitic, anti-tumoral effects or diagnostic and/or therapeutic
Resumo:
In the present study, extracts rich-sulfated polysaccharides were obtained from three different species of Dictyotales (a class of brown macroalgae): Canistrocarpus cervicornis, Dictyota mertensii and Dictyopteris delicatula and their anticoagulant and antioxidant activities were evaluated. All extracts showed anticoagulant activity on aPTT assay, but not on PT assay. Extracts also exhibited total antioxidant activity, superoxide radical scavenging capacity and ferric chelating property. The extract from C. cervicornis showed the best results and was choose to have their sulfated polysaccharides fractioned and subsequently analysed. Thus, six fractions (CC-0.3, CC-0.5, CC-0.7, CC-1.0, CC-1.2 and CC-2.0) were obtained by proteolysis followed by sequential acetone precipitation. Agarose gel eletrophoresis stained with blue toluidine, confirmed the presence of sulfated polysaccharides in all fractions. Chemical analyses showed that all fractions presented heterofucans mainly constitued by fucose, galactose, glucuronic acid and sulfate. Any fraction changed the PT. However, all fractions were able to double the aPTT on a dose-dependent manner. CC- 0.3, CC-0.5, CC-0.7 and CC-1.0 needed only 0.100 mg/mL to double the aPTT, result only 1.25 times higher than the Clexane® (0.080 mg/mL), a commercial low molecular heparin. The heterofucans presented appreciable total antioxidant capacity, low capacity on scavenging hydroxyl radical and good efficiency on scavenging superoxide radicals (except CC-1.0). CC-1.2 showed 43.1 % on superoxide radical scavenging. This result was higher than that showed by the same concentration of gallic acid (41.8 %), a known antioxidant. Furthermore, the heterofucans showed excelent activity on ferrous chelating activity (except CC-0.3). CC-0.5, CC-0.7 and CC-1.0 showed the highest activities with 47.0 % of ferrous chelating activity, a result 2.0 times lesser than that exhibited by the same concentration of EDTA. These results clearly indicated the beneficial effects of heterofucans extracted from C. cervicornis as potential anticoagulant and antioxidant agents. However additional steps of purification, structural studies, besides in vivo experiments are needed for these fucans may be used as therapeutic agents
Resumo:
Protein and caloric malnutrition has been considered one of the most concerned endemic diseases in Brazil and in the world. It has been known that depletion or reduction of proteins as far as meals are concerned can steer irreversible damages upon several organic systems. This study had as aim evaluate the effects the low-protein diet had over the formation and composition of the teeth components. 18 females and 6 males were used for the experiment. 12 from the 18 females had undertaken the low-protein diet (DH) for 03 weeks and the other 6, which remained, and those males had undertaken a controlled diet (DC) for the same period. All animals had the diets during their mating, pregnancy and lactation cycle. As soon as the offsprings had been born, 10 young males and females of each group faced a disease hood analysis to check the teeth germs of their lower fore teeth. The rest of the group had their lactation cycle normally 60 days. Then they were put to death and had their lower fore teeth removed both to be analyzed through a scanning electronic microscopy (SEM) of the structure alterations and to have their calcium checked by an atomic absorption of the phosphorus vanadate-molibdate method and by other minerals EDX method. The animals livers were removed to have their hepatic proteins analyzed as well. The histopatologic study showed that at first day of birth, all animals had their lower fore teeth come out. It was verified that 90% of the animals teeth were in an apposition and calcification period and it was possible to observe the dentin formation from 60% of the 90% already mentioned. Through the SEM method it could be realized that 90% of the animals of the DH group had their lower fore teeth easily broken and no definite shape. In this same group itself, it was also observed long micro fissures 369,66 nm ± 3,45 while the DC group had fissures of 174 nm ± 5,72. Now regarding the calcium and phosphorus concentration, it could be noticed that there was a great reduction of these components and other minerals in the DH group. Almost all minerals, except for the Cl and K, presented higher levels in the DC group enamel.The reduction of the protein input greatly influenced the offsprings´ weight and height. However the hepatic proteins had no important difference between the groups what can make one believe that those animals suffered from protein malnutrition of marasmic kind
Resumo:
The gradual replacement of conventional materials by the ones called composite materials is becoming a concern about the response of these composites against adverse environmental conditions, such as ultraviolet radiation, high temperature and moist. Also the search for new composite using natural fibers or a blend of it with synthetic fibers as reinforcement has been studied. In this sense, this research begins with a thorough study of microstructural characterization of licuri fiber, as a proposal of alternative reinforcement to polymeric composites. Thus, a study about the development of two composite laminates was done. The first one, involving only the fiber of licuri and the second comprising a hybrid composite based of fiber glass E and the fiber of licuri, in order to know the performance of the fiber when of fiber across the hybridization process. The laminates were made in the form of plates using the tereftálica ortho-polyester resin as matrix. The composite laminate made only by licuri fiber had two reinforcing fabric layers of unidirectional licuri and the hybrid composite had two reinforcing layers of unidirectional licuri fabric and three layers of fiber short glass-E mat. Finally, both laminates was exposed to aging acceleration in order to study the influence of environmental degradation involving the mechanical properties and fracture characteristics thereof. Regarding the mechanical properties of composites, these were determined through uniaxial tensile tests, uniaxial compression and three bending points for both laminates in original state, and uniaxial tensile tests and three bending points after accelerated aging. As regards the study of structural degradation due to aging of the laminates, it was carried out based on microscopic analysis and microstructure, as well as measuring weight loss. The characteristics of the fracture was performed by macroscopic and microscopic (optical and SEM) analysis. In general, the laminated composites based on fiber licuri showed some advantages in their responses to environmental aging. These advantages are observed in the behavior related to stiffness as well as the microstructural degradation and photo-oxidation processes. However, the structural integrity of this laminate was more affected in case the action of uniaxial tensile loads, where it was noted a lower rate of withholding his last resistance property
Resumo:
The addition of active silica potentially improves the quality of concrete due to its high reactivity and pore refinement effect. The reactivity of silica is likely related to its charge density. Variations in surface charge alter the reactivity of the material consequently affecting the properties of concrete. The present study aimed at investigating variations in the charge density of silica as a function of acid treatments using nitric or phosphoric acid and different pH values (2.0, 4.0 and 6.0). Effects on concrete properties including slump, mechanical strength, permeability and chloride corrosion were evaluated. To that end, a statistical analysis was carried out and empirical models that correlate studied parameters (pH, acid and cement) with concrete properties were established. The quality of the models was tested by variance analysis. The results revealed that the addition of silica was efficiency in improving the properties of concrete, especially the electrochemical parameters. The addition of silica treated using nitric acid at pH = 4.0 displayed the best cement performance including highest strength, reduced permeability and lowest corrosion current
Resumo:
As most current studies, reinforced plastics have been, in recent years, a viable alternative in building structural elements of medium and large, since the lightness accompanied by high performance possible. The design of hybrid polymer composites (combination of different types of reinforcements) may enable structural applications thereof, facing the most severe service conditions. Within this class of composite materials, reinforced the underlying tissues hybrid high performance are taking space when your application requires high load bearing and high rigidity. The objective of this research work is to study the challenges in designing these fabrics bring these materials as to its mechanical characterization and fracture mechanisms involved. Some parameters associated with the process and / or form of hybridization stand out as influential factors in the final performance of the material such as the presence of anisotropy, so the fabric weave, the process of making the same, normative geometry of the specimens, among others. This sense, four laminates were developed based hybrid reinforcement fabrics involving AS4 carbon fiber, kevlar and glass 49-E as the matrix epoxy vinyl ester resin (DERAKANE 411-350). All laminates were formed each with four layers of reinforcements. Depending on the hybrid fabric, all the influencing factors mentioned above have been studied for laminates. All laminates were manufactured industrially used being the lamination process manual (hand-lay-up). All mechanical characterization and study of the mechanism of fracture (fracture mechanics) was developed for laminates subjected to uniaxial tensile test, bending in three and uniaxial compression. The analysis of fracture mechanisms were held involving the macroscopic, optical microscopy and scanning electron microscopy
Resumo:
Currently, computational methods have been increasingly used to aid in the characterization of molecular biological systems, especially when they relevant to human health. Ibuprofen is a nonsteroidal antiinflammatory or broadband use in the clinic. Once in the bloodstream, most of ibuprofen is linked to human serum albumin, the major protein of blood plasma, decreasing its bioavailability and requiring larger doses to produce its antiinflamatory action. This study aimes to characterize, through the interaction energy, how is the binding of ibuprofen to albumin and to establish what are the main amino acids and molecular interactions involved in the process. For this purpouse, it was conducted an in silico study, by using quantum mechanical calculations based on Density Functional Theory (DFT), with Generalized Gradient approximation (GGA) to describe the effects of exchange and correlation. The interaction energy of each amino acid belonging to the binding site to the ligand was calculated the using the method of molecular fragmentation with conjugated caps (MFCC). Besides energy, we calculated the distances, types of molecular interactions and atomic groups involved. The theoretical models used were satisfactory and show a more accurate description when the dielectric constant ε = 40 was used. The findings corroborate the literature in which the Sudlow site I (I-FA3) is the primary binding site and the site I-FA6 as secondary site. However, it differs in identifying the most important amino acids, which by interaction energy, in order of decreasing energy, are: Arg410, Lys414, Ser 489, Leu453 and Tyr411 to the I-Site FA3 and Leu481, Ser480, Lys351, Val482 and Arg209 to the site I-FA6. The quantification of interaction energy and description of the most important amino acids opens new avenues for studies aiming at manipulating the structure of ibuprofen, in order to decrease its interaction with albumin, and consequently increase its distribution