Análise do custo-benefício de sistemas de cobertas em edificações comerciais para o clima de Natal/RN visando eficiência energética

This research consists in studying the influence of the various type of construction systems of roofs with their energy efficiency as well as on the cost benefit for the commercial buildings on the temperatures condition of the city of Natal/RN. The main goal of this research is to analyze the cost benefit of the construction systems of roofs available on the market, taking into consideration the energy efficiency of the commercial buildings artificially air conditioned in order to be used by the projectors and to be adequated to the temperatures condition of the city of Natal/RN. The method of valuation of the cost benefit of roof systems consists in six steps: Features and simulation of the reference building; Analyze of sensitivity; Analyzes, features and simulation of alternatives of roof construction systems; Analyze of the cost of implementation; Analyze of the benefits of the alternatives comparing to the base case; And finally the analyze of the cost benefit. The model type chosen as reference was stores with pre molded buildings and system of roof with fiber ciment and ceiling . The thermal results showed the influence of the roof system on the energy efficiency of the building. The Final results of the simulations of the alternatives comes to a conclusion that the absortance is the variable that presents the best cost benefit relation and the reduction on the thermal transmittance still has limitations because of the high cost

A Fruticultura Irrigada de pequenos produtores no Baixo-Açu: Uma análise da eficiência de custo

This work has as an objective analyze the efficiency of producers costs of the irrigation Project Baixo-Açu , and identify the determining factors of this efficiency. To achieve these targets it was estimated, in a first stage, a frontier of costs by the method, non parametric of Data Envelopment Analysis-DEA, and measured the stakes of efficiency producers. On the second stage, it was utilized the Tobit regression pattern, estimating an inefficiency function of costs, and were indentified the associated factors of resources waste. Among the results found it was noticed the existence of a high waste of resources, that represent more than 54% of effective cost. Among the factors with the highest wastes are: energy, herbicides, defensives and chemical fertilizers. In a general way, the producers presented low efficiency level and, only, two, of seventy-five researched, achieved the frontier of costs minimization. These results reveal, in a certain way, that the producers in irrigated fruit growing in the project Baixo-Açu don t seek to minimize the production costs. It was still noticed, that the reduction of resources waste, and this way the inefficiency of costs, is associated with the agriculturalist education, his experience in agriculture, his access to the technical assistance and credit

Custo social de oportunidade na trajetória de acesso ao ensino superior: o caso dos ingressantes na UFRN nos vestibulares de 2006 a 2010

Access is a problem of higher education in Brazil that has existed since the formalization of this has occurred since the installation of the Portuguese court in Brazil in 1808. Only 10% of young people between 18 and 24 years of age attending this level of education in 2000, arriving in 2010 just 15%, far from that determined the National Education Plan in 2001, triple that percentage by the year 2010. In addition, a majority of seats of public HEIs is populated by students from the private network, especially in high-demand courses. In this context, this study aims to identify the costs related to the trajectories of students who were successful in the vestibular UFRN editions from 2006 to 2010. Presents an overview of higher education in Brazil, a brief history of vestibular, as well as new forms of access, and some of the policies to expand such access, highlighting the argument Inclusion UFRN. Focusing on the theme of the paper presents the concepts of opportunity costs and social. After collecting data through a questionnaire and consultation of databases COMPERVE was developed to search for a descriptive and analytical, with the participation of 3,995 students, of whom 1642 (41.1%) had completed secondary education in schools public, and 2,078 (52%) in private schools. The profile indicates that 90% are single, about 50% are 21 years of age, are white and female. In the course of preparation for college entrance exams, 80% chose the course during or after completion of the last year of high school, and almost 70% said they had started preparing at that time. Findings related to the costs involved with this preparation indicate that, in most cases there were school fees and disbursements and workshops, and the purchase of books and other materials, with parents primarily responsible for this cost, the amount disbursed each month was up $ 300 for 64% of respondents and only 7% of them exceeded $ 1,000, the major non-financial costs were characterized by the following resignations: job opportunities (24%) or temporary work (20%) courses of languages (26%), leisure activities (48%), leisure travel (43%), and parties and / or shows (54%). Of social investments by the government, stand out in the tax waiver scholarships for study in private institutions, grant exemption from the registration fee of vestibular, the preparatory courses UFRN, and seminars by COMPERVE / UFRN with networks of high school. From the junction of the opportunity costs (private costs) and social costs (public costs), a new concept: the social opportunity cost, which measures the combined efforts of families and government to finance the opportunity to access higher education of an individual. This concept can and should be incorporated as a strategic vector for the sake of democratic university, which reflects the social model that is sought

Custo-efetividade da terapia compressiva no processo de cicatrização de úlceras venosas

Analytical study of therapeutic nonrandomized intervention type, intra-group controlled, with the aim of analyzing the cost-effectiveness of compression therapy with manipulated Unna boot in relation to conventional therapy in the healing of venous ulcers (VU) of patients treated in ambulatory clinic. The study population was composed by patients with VU treated by angiologists in Surgical Clinic Ambulatory of the Onofre Lopes University Hospital (HUOL) with a sample of 18 patients. It obtained the assent of the HUOL Ethics in Research Committee (Protocol 276/09). Data collection was performed over a period of four months by the own master's student and 34 nursing students, through the application of the research instrument in the admission of patients to the study and in the ten subsequent evaluations, performed at the time of changing Unna boot, weekly, for a maximum period of 10 weeks. The data were analyzed with SPSS 15.0 software, using descriptive and inferential statistics, and presented as tables, charts and graphs. Among those surveyed, prevailed: females, mean age 57.6 years, low education and income levels, most retired, unemployed or off work, with the standing position more than six hours per day and up to eight hours daily of domestic or occupational activities. In health status profile of respondents there were predominantly sleep, rest and inadequate elevation of the lower limbs, no smoking and/or alcohol use, presence of hypertension and no use of drugs. Most presented the first VU for over 10 years, recurrences, present VU for more than five years, involvement of left leg, in malleolar and / or distal leg region, mild edema, hyperpigmentation, lipodermatosclerosis, telangiectasies, reticular and varicose veins, mild pain, serous exudate in moderate quantity, small lesions (up to 50cm2), with predominance of granulation tissue and / or epithelialization and demarcated, elevated and irregular borders, with crusts and macerated. Most patients reported that in the 10 weeks prior to admission, made bandages at home and / or Basic Health Unit and / or ambulatory, with nursing aides or technicians, daily, and on weekends or holidays, performed by patients themselves, using healing ointment on the lesion, being observed granulation / epithelialization and increase in VU prevalent in the 10 weeks of traditional treatment. After follow up with manipulated Unna boot, was observed a decrease of lesions in all study patients, with complete healing in 27.8% of those between 1 and 5 weeks of treatment, with satisfactory evolution of the lesions, pain and ankle and calf circumferences, and unsatisfactory development of the borders of ulcers, edema, sleep, rest and elevation of the lower limbs, especially in more chronic patients. Furthermore, patients who achieved total healing and exhibited the greatest percentage reduction of lesions had a higher number of wound healing factors (ρ = 0.01 and ρ = 0.027, respectively). The manipulated Unna boot showed better results in those patients with shorter duration of injury, leading them to a satisfactory outcome within a short period of treatment. After the cost-effectiveness analysis, we conclude that the manipulated Unna boot is more effective than conventional therapy in the healing process of VU and is more cost-effective in patients with shorter lesions (ρ = 0.001), shorter treatment (ρ = 0.000) and greater number of wound healing factors (ρ = 0.005).

Heurísticas usando construção de vocabuilário aplicadas ao problema da atribuição de localidades a anéis em redes SONET/SDH

The SONET/SDH Ring Assignment Problem (PALAS) treats to group localities in form of some rings, being respected the traffic's limitations of the equipment. Each ring uses a DXC (Digital Cross Connect) to make the communication with the others, being the DXC the equipment most expensive of the net, minimizing the number total of rings, will minimize the total net cost, problem's objective . This topology in rings provides a bigger capacity of regeneration. The PALAS is a problem in Combinatorial Optimization of NP-hard Class. It can be solved through Heuristics and Metaheuristics. In this text, we use Taboo Search while we keep a set of elite solutions to be used in the formation of a part of the collection of vocabulary's parts that in turn will be used in the Vocabulary Building. The Vocabulary Building will be started case Taboo Search does not reach the best solution for the instance. Three approaches had been implemented: one that only uses vocabulary's parts deriving of Taboo Search, one that it only uses vocabulary's parts randomly generated and a last one that it uses half come of the elite and half randomly generated

Algoritmo evolutivo paralelo para o problema de atribuição de localidades a anéis em redes sonet/sdh

The telecommunications play a fundamental role in the contemporary society, having as one of its main roles to give people the possibility to connect them and integrate them into society in which they operate and, therewith, accelerate development through knowledge. But as new technologies are introduced on the market, increases the demand for new products and services that depend on the infrastructure offered, making the problems of planning of telecommunication networks become increasingly large and complex. Many of these problems, however, can be formulated as combinatorial optimization models, and the use of heuristic algorithms can help solve these issues in the planning phase. This paper proposes the development of a Parallel Evolutionary Algorithm to be applied to telecommunications problem known in the literature as SONET Ring Assignment Problem SRAP. This problem is the class NP-hard and arises during the physical planning of a telecommunication network and consists of determining the connections between locations (customers), satisfying a series of constrains of the lowest possible cost. Experimental results illustrate the effectiveness of the Evolutionary Algorithm parallel, over other methods, to obtain solutions that are either optimal or very close to it

Uso de técnicas de otimização baseadas em derivadas como suporte do planejamento operacional de redes de distribuição de energia elétrica

The usual programs for load flow calculation were in general developped aiming the simulation of electric energy transmission, subtransmission and distribution systems. However, the mathematical methods and algorithms used by the formulations were based, in majority, just on the characteristics of the transmittion systems, which were the main concern focus of engineers and researchers. Though, the physical characteristics of these systems are quite different from the distribution ones. In the transmission systems, the voltage levels are high and the lines are generally very long. These aspects contribute the capacitive and inductive effects that appear in the system to have a considerable influence in the values of the interest quantities, reason why they should be taken into consideration. Still in the transmission systems, the loads have a macro nature, as for example, cities, neiborhoods, or big industries. These loads are, generally, practically balanced, what reduces the necessity of utilization of three-phase methodology for the load flow calculation. Distribution systems, on the other hand, present different characteristics: the voltage levels are small in comparison to the transmission ones. This almost annul the capacitive effects of the lines. The loads are, in this case, transformers, in whose secondaries are connected small consumers, in a sort of times, mono-phase ones, so that the probability of finding an unbalanced circuit is high. This way, the utilization of three-phase methodologies assumes an important dimension. Besides, equipments like voltage regulators, that use simultaneously the concepts of phase and line voltage in their functioning, need a three-phase methodology, in order to allow the simulation of their real behavior. For the exposed reasons, initially was developped, in the scope of this work, a method for three-phase load flow calculation in order to simulate the steady-state behaviour of distribution systems. Aiming to achieve this goal, the Power Summation Algorithm was used, as a base for developping the three phase method. This algorithm was already widely tested and approved by researchers and engineers in the simulation of radial electric energy distribution systems, mainly for single-phase representation. By our formulation, lines are modeled in three-phase circuits, considering the magnetic coupling between the phases; but the earth effect is considered through the Carson reduction. Its important to point out that, in spite of the loads being normally connected to the transformers secondaries, was considered the hypothesis of existence of star or delta loads connected to the primary circuit. To perform the simulation of voltage regulators, a new model was utilized, allowing the simulation of various types of configurations, according to their real functioning. Finally, was considered the possibility of representation of switches with current measuring in various points of the feeder. The loads are adjusted during the iteractive process, in order to match the current in each switch, converging to the measured value specified by the input data. In a second stage of the work, sensibility parameters were derived taking as base the described load flow, with the objective of suporting further optimization processes. This parameters are found by calculating of the partial derivatives of a variable in respect to another, in general, voltages, losses and reactive powers. After describing the calculation of the sensibility parameters, the Gradient Method was presented, using these parameters to optimize an objective function, that will be defined for each type of study. The first one refers to the reduction of technical losses in a medium voltage feeder, through the installation of capacitor banks; the second one refers to the problem of correction of voltage profile, through the instalation of capacitor banks or voltage regulators. In case of the losses reduction will be considered, as objective function, the sum of the losses in all the parts of the system. To the correction of the voltage profile, the objective function will be the sum of the square voltage deviations in each node, in respect to the rated voltage. In the end of the work, results of application of the described methods in some feeders are presented, aiming to give insight about their performance and acuity

Plataforma Robótica de Baixíssimo Custo para Robótica Educacional

Robots are present each time more on several areas of our society, however they are still considered expensive equipments that are restricted to few people. This work con- sists on the development of control techniques and architectures that make possible the construction and programming of low cost robots with low programming and building complexity. One key aspect of the proposed architecture is the use of audio interfaces to control actuators and read sensors, thus allowing the usage of any device that can produce sounds as a control unit of a robot. The work also includes the development of web ba- sed programming environments that allow the usage of computers or mobile phones as control units of the robot, which can be remotely programmed and controlled. The work also includes possible applications of such low cost robotic platform, including mainly its educational usage, which was experimentally validated by teachers and students of seve- ral graduation courses. We also present an analysis of data obtained from interviews done with the students before and after the use of our platform, which confirms its acceptance as a teaching support tool

Otimização de superfícies seletivas de frequência com elementos pré-fractais utilizando rede neural MLP e algoritmos de busca populacional

This thesis describes design methodologies for frequency selective surfaces (FSSs) composed of periodic arrays of pre-fractals metallic patches on single-layer dielectrics (FR4, RT/duroid). Shapes presented by Sierpinski island and T fractal geometries are exploited to the simple design of efficient band-stop spatial filters with applications in the range of microwaves. Initial results are discussed in terms of the electromagnetic effect resulting from the variation of parameters such as, fractal iteration number (or fractal level), fractal iteration factor, and periodicity of FSS, depending on the used pre-fractal element (Sierpinski island or T fractal). The transmission properties of these proposed periodic arrays are investigated through simulations performed by Ansoft DesignerTM and Ansoft HFSSTM commercial softwares that run full-wave methods. To validate the employed methodology, FSS prototypes are selected for fabrication and measurement. The obtained results point to interesting features for FSS spatial filters: compactness, with high values of frequency compression factor; as well as stable frequency responses at oblique incidence of plane waves. This thesis also approaches, as it main focus, the application of an alternative electromagnetic (EM) optimization technique for analysis and synthesis of FSSs with fractal motifs. In application examples of this technique, Vicsek and Sierpinski pre-fractal elements are used in the optimal design of FSS structures. Based on computational intelligence tools, the proposed technique overcomes the high computational cost associated to the full-wave parametric analyzes. To this end, fast and accurate multilayer perceptron (MLP) neural network models are developed using different parameters as design input variables. These neural network models aim to calculate the cost function in the iterations of population-based search algorithms. Continuous genetic algorithm (GA), particle swarm optimization (PSO), and bees algorithm (BA) are used for FSSs optimization with specific resonant frequency and bandwidth. The performance of these algorithms is compared in terms of computational cost and numerical convergence. Consistent results can be verified by the excellent agreement obtained between simulations and measurements related to FSS prototypes built with a given fractal iteration

Uma proposta de metodologia para o ensino de Física usando robótica de baixíssimo custo

This paper presents methodology based on Lev Vigotsky`s social interactionist theory through investigative activities, which integrates the teaching of physics to robotics, directed to students of the Physics degree course, seeking to provide further training for future teachers. The method is organized through educational robotics workshops that addresses concepts of physics through the use of low-cost educational robots along with several activities. The methodology has been presented and discussed and put into practice afterwards in workshops so that these future teachers may be able to take robotics to their classroom. Students from the last and penultimate semester of the Physics degree course of the Federal Institute of Education, Science and Technology of Rio Grande do Norte, Caicó campus participated in this project

Viabilidades térmica, econômica e de materiais de um sistema solar de aquecimento de água a baixo custo para fins residenciais

An solar alternative system for water heating is presented. Is composed for one low cost alternative collector and alternative thermal reservoir for hot water storing. The collector of the system has box confectioned in composite material and use absorption coils formed for PVC tubes. The box of hot water storage was confectioned from a plastic polyethylene drum used for storage of water and garbage, coated for a cylinder confectioned in fiber glass. The principle of functioning of the system is the same of the conventionally. Its regimen of work is the thermosiphon for a volume of 250 liters water. The main characteristic of the system in considered study is its low cost, allowing a bigger socialization of the use of solar energy. It will be demonstrated the viabilities thermal, economic and of materials of the system of considered heating, and its competitiveness in relation to the available collectors commercially. Relative aspects will be boarded also the susceptibility the thermal degradation and for UV for the PVC tubes. It will be shown that such system of alternative heating, that has as main characteristic its low cost, presents viabilities thermal, economic and of materials

Otimização Topológica com Termo-elasticidade Utilizando Elementos Tri3

This work proposes a formulation for optimization of 2D-structure layouts submitted to mechanic and thermal shipments and applied an h-adaptive filter process which conduced to computational low spend and high definition structural layouts. The main goal of the formulation is to minimize the structure mass submitted to an effective state of stress of von Mises, with stability and lateral restriction variants. A criterion of global measurement was used for intents a parametric condition of stress fields. To avoid singularity problems was considerate a release on the stress restriction. On the optimization was used a material approach where the homogenized constructive equation was function of the material relative density. The intermediary density effective properties were represented for a SIMP-type artificial model. The problem was simplified by use of the method of finite elements of Galerkin using triangles with linear Lagrangian basis. On the solution of the optimization problem, was applied the augmented Lagrangian Method, that consists on minimum problem sequence solution with box-type restrictions, resolved by a 2nd orderprojection method which uses the method of the quasi-Newton without memory, during the problem process solution. This process reduces computational expends showing be more effective and solid. The results materialize more refined layouts with accurate topologic and shape of structure definitions. On the other hand formulation of mass minimization with global stress criterion provides to modeling ready structural layouts, with violation of the criterion of homogeneous distributed stress

Estudo da Potencialidade da produção de tijolos de adobe misturado com outros materiais: uma alternativa de baixo custo para a construção civil

The production of the red pottery brick, made traditionally with clay, is a technique that is already stabled. However, in spite of the little complexity that involves the conventional process of these bricks production, it are exposed to many problems that begin in the fase of exploration of the mines, the problems get worse because of the lack of the clay's characterization, and they continue through the steps of the dough preparation, conformation of the products, the drying and the burning process. The wastefulness is shown and so is the low quality of the material produced. Among other factors, the high use of energy in the burning makes the cost of this material inaccessible to the low income consumer. Besides this, the destruction of the environment around the mines and the use of native vegetation to produce wood - the most used fuel in the pottery industry - make serious environmental damage. The production technique of a new type of simple brick (adobe), that has low cost and no environmental damage, can be the viable altemative to lower the cost of this part of the civil construction, and, consequently, in the building of cheaper houses. In this paper, the results of the mechanical resistance of the adobe brick are shown, using in its composition, clay, natural vegetable fibers, cement and plaster in a process that is completely handcrafted and manual. It is intented to make clear that are possible alternatives to be put in practice, with the simple process, using "raw earth" that has been used in the construction of houses in thousands of years, trying to solve these severe problems. Analysis and tests were performed to find results that could prove the possibility of the utilization of this kind of material. Other studies are in progress, and the new researches are necessary to enrich this work, but it stays the certainty that there is potential to produce bricks from adobe, as an alternative that has low cost to civil construction

Construção, calibração e análise de desempenho de um piranômetro de baixo custo, baseado no modelo Kimball-Hobbs

In this work a pyrometer using the classic model of Kimball-Hobbs was developed, tested and calibrated. The solar radiation is verified through the temperature difference between the sensible elements covered by absorbing (black) and reflecting (white) pigmentations of the incoming radiation. The photoacoustic technique was used to optimize the choice of the pigments. Methodologies associated with linearity, thermo-variation, sensibility, response time and distance are also presented. To correctly classify the results, the international standard ISO 9060 as well as indicative parameters of World Meteorological Organization (WMO) are used. In addition a system of data acquisition of two channels with 12 bits, constructed during the this time, was used to measure the global solar radiation on the ground by the pyrometer and also by another pyrometer certified in the case of Keep & zonen. The results statistically show, through the hypothesis test presented here, that both equipments find population average with 95% of correctness

Projeto, construção e análise de desempenho de um forno solar alternativo tipo caixa a baixo custo

An alternative box-type solar oven constructed from the scrap iron of a gas conventional cook is presented, which functions principles are the effect greenhouse and the concentration. The oven of the conventional cook is the baking enclosure where the absorber (pot) of the solar oven is located, being re-covered for a glass blade for the generation of the greenhouse effect isolated lateral and having deep its and for a composite the plaster base and EPS. Segments of plain mirrors had been placed in the laterals of the oven for the concentration of the radiation and a reflecting parabola was introduced in the baking enclosure for the exploitation of the incident reflected radiation in the interior of the oven. The oven is mobile to allow one better aiming of exactly in relation to the apparent movement of the sun. The thermal economic and of materials viabilities of the stove in study will be demonstrate The average internal temperature of the absorber was around 150°C and the internal temperature around 120°C. Will demonstrate that its low cost and good thermal performance represents basic characteristics for the viability of large use of such archetype, mainly for cooking the decreases and averages temperatures. One will reveal that the archetype in study is competitive with the box-type solar cooker conceived in the whole world