Pirólise de borras oleosas de petroleo utilizando nanomateriais

The oily sludge is a complex mix of hydrocarbons, organic impurities, inorganic and water. One of the major problems currently found in petroleum industry is management (packaging, storage, transport and fate) of waste. The nanomaterials (catalysts) mesoporous and microporous are considered promising for refining and adsorbents process for environment protection. The aim of this work was to study the oily sludge from primary processing (raw and treated) and vacuum residue, with application of thermal analyses technique (pyrolysis), thermal and catalytic pyrolysis with nanomaterials, aiming at production petroleum derived. The sludge and vacuum residue were analyzed using a soxhlet extraction system, elemental analysis, thin layer chromatography, thermogravimetry and pyrolysis coupled in gas chromatography/mass spectrometry (Py GC MS). The catalysts AlMCM-41, AlSBA-15.1 e AlSBA-15.2 were synthesized with molar ratio silicon aluminum of 50 (Si/Al = 50), using tetraethylorthosilicante as source of silicon and pseudobuhemita (AlOOH) as source of aluminum. The analyzes of the catalysts indicate that materials showed hexagonal structure and surface area (783,6 m2/g for AlMCM-41, 600 m2/g for AlSBA-15.1, 377 m2/g for AlSBA-15.2). The extracted oily sludge showed a range 65 to 95% for organic components (oil), 5 to 35% for inorganic components (salts and oxides) and compositions different of derivatives. The AlSBA-15 catalysts showed better performance in analyzes for production petroleum derived, 20% increase in production of kerosene and light gas oil. The energy potential of sludge was high and it can be used as fuel in other cargo processed in refinery

Direito fundamental à saúde: parâmetros e alternativas para sua concretização no Brasil

If, on one hand, only with the 1988 Federal Constitution the right to health began to receive the treatment of authentic fundamental social right; on the other, it is certain since then, the level of concretization reached as to such right depicts a mismatch between the constitutional will and the will of the rulers. That is because, despite the inherent gradualness of the process of concretization of the fundamental social rights, the Brazilian reality, marked by a picture of true chaos on public health routinely reported on the evening news, denatures the priority status constitutionally drew for the right to health, demonstrating, thus, that there is a clear deficit in this process, which must be corrected. This concern regarding the problem of the concretization of the social rights, in turn, is underlined when one speaks of the right to health, since such right, due to its intimate connection with the right to life and human dignity, ends up assuming a position of primacy among the social rights, presenting itself as an imperative right, since its perfect fruition becomes an essential condition for the potential enjoyment of the remaining social rights. From such premises, this paper aims to provide a proposal for the correction of this problem based upon the defense of an active role of the Judiciary in the concretization of the right to health as long as grounded to objective and solid parameters that come to correct, with legal certainty, the named deficit and to avoid the side effects and distortions that are currently beheld when the Judiciary intends to intervene in the matter. For that effect, emerges as flagship of this measure a proposition of an existential minimum specific to the right to health that, taking into account both the constitutionally priority points relating to this relevant right, as well as the very logic of the structuring of the Sistema Único de Saúde - SUS inserted within the core of the public health policies developed in the country, comes to contribute to a judicialization of the subject more in alignment with the ideals outlined in the 1988 Constitution. Furthermore, in the same intent to seek a concretization of the right to health in harmony with the constitutional priority inherent to this material right, the research alerts to the need to undertake a restructuring in the form of organization of the Boards of Health in order to enforce the constitutional guideline of SUS community participation, as well as the importance of establishing a new culture budget in the country, with the Constitution as a compass, pass accurately portray a special prioritization directed constitutional social rights, especially the right to health

Desenvolvimento de metodologia para avaliação de desempenho ambiental em edifícios adaptada à realidade do Nordeste brasileiro

This research refers to the production of green buildings, defined, mainly, based on the use of sources of alternative energies, smaller emission of pollutant, use of recyclable materials, systems of recycling of the waters, maximization of the natural illumination, preservation of green areas or native, and appropriate quality of the internal air. From the conception of those buildings, it appears the needs of evaluating them, creating the methodologies for the evaluation of environmental performance of buildings. In that way, this work can be divided in two moments: the first one when it identifies the methodologies for the evaluation of environmental performance for buildings existents in the literature, defining their categories, criteria and sub-criteria to be appropriate to the reality of the Brazilian Northeast; and the second one when starting from the analysis of the systems of existent evaluation. It defines a methodological base and it generates a new evaluation system, denominated MEDACNE (Methodology of Evaluation of Environmental Acting for Construction in the Northeast). In that moment, the process of framing of the section of the building site is verified under the maintainable optics, stimulated mainly by the pressures of the society - conferences, protocols and agreements. Finally, the proposed methodology was applied in a case study, a residential building, called Maria José Gurgel , located in Natal-RN, Brazil, for its validation. This methodological proposition should increase the patterns environmental places for the production of new buildings, and it will be a reference guide for architects, engineers and planners to develop their constructions considering the criteria of the sustainability. This study made use of bibliographical research in books and specialized magazines and the analysis of the data was realized in an interpretative way

Estudo da Potencialidade da produção de tijolos de adobe misturado com outros materiais: uma alternativa de baixo custo para a construção civil

The production of the red pottery brick, made traditionally with clay, is a technique that is already stabled. However, in spite of the little complexity that involves the conventional process of these bricks production, it are exposed to many problems that begin in the fase of exploration of the mines, the problems get worse because of the lack of the clay's characterization, and they continue through the steps of the dough preparation, conformation of the products, the drying and the burning process. The wastefulness is shown and so is the low quality of the material produced. Among other factors, the high use of energy in the burning makes the cost of this material inaccessible to the low income consumer. Besides this, the destruction of the environment around the mines and the use of native vegetation to produce wood - the most used fuel in the pottery industry - make serious environmental damage. The production technique of a new type of simple brick (adobe), that has low cost and no environmental damage, can be the viable altemative to lower the cost of this part of the civil construction, and, consequently, in the building of cheaper houses. In this paper, the results of the mechanical resistance of the adobe brick are shown, using in its composition, clay, natural vegetable fibers, cement and plaster in a process that is completely handcrafted and manual. It is intented to make clear that are possible alternatives to be put in practice, with the simple process, using "raw earth" that has been used in the construction of houses in thousands of years, trying to solve these severe problems. Analysis and tests were performed to find results that could prove the possibility of the utilization of this kind of material. Other studies are in progress, and the new researches are necessary to enrich this work, but it stays the certainty that there is potential to produce bricks from adobe, as an alternative that has low cost to civil construction

Fibras de sisal (Agave sisalana) como isolante térmico de tubulações

In the last decades there was a significant increasing of the numbers of researchers that joint efforts to find alternatives to improve the development of low environmental impact technology. Materials based on renewable resources have enormous potentials of applications and are seen as alternatives for the sustainable development. Within other parameters, the sustainability depends on the energetic efficiency, which depends on the thermal insulation. Alternative materials, including vegetal fibers, can be applied to thermal insulation, where its first goal is to minimize the loss of energy. In the present research, it was experimentally analyzed the thermal behavior of fiber blankets of sisal (Agave sisalana) with and without surface treatment with oxide hidroxide (NaOH). Blankets with two densities (1100/1200 and 1300/1400 g/m2) were submitted to three rates of heat transfer (22.5 W, 40 W and 62.5 W). The analysis of the results allowed comparing the blankets treated and untreated in each situation. Others experiments were carried out to obtain the thermal conductivity (k), heat capacity (C) and the thermal diffusivity (α) of the blankets. Thermo gravimetric analyses were made to the verification of the thermal stability. Based on the results it was possible to relate qualitatively the effect of the heat transfer through the sisal blankets subjected to three heat transfer rates, corresponding to three temperature values (77 °C, 112 °C e 155 °C). To the first and second values of temperature it was verified a considerable reduction on the rate of heat transfer; nevertheless, to the third value of temperature, the surface of the blankets (treated and untreated) in contact with the heated surface of the tube were carbonized. It was also verified, through the analyses of the results of the measurements of k, C e α, that the blankets treated and untreated have values near to the conventional isolating materials, as glass wool and rock wool. It could be concluded that is technically possible the use of sisal blankets as constitutive material of thermal isolation systems in applications where the temperature do not reach values greater than 112 ºC

Desenvolvimento de um compósito de espuma rígida de poliuretana de mamona e fibras de sisal para isolação térmica

The search for sustainable technologies that can contribute to reduce energy consumption is a great challenge in the field of insulation materials. In this context, composites manufactured from vegetal sources are an alternative technology. The principal objectives of this work are the development and characterization of a composite composed by the rigid polyurethane foam derived from castor oil (commercially available as RESPAN D40) and sisal fibers. The manufacture of the composite was done with expansion controlled inside a closed mold. The sisal fibers where used in the form of needlepunched nonwoven with a mean density of 1150 g/m2 and 1350 g/m2. The composite characterization was performed through the following tests: thermal conductivity, thermal behavior, thermo gravimetric analysis (TG/DTG), mechanical strength in compression and flexural, apparent density, water absorption in percentile, and the samples morphology was analyzed in a MEV. The density and humidity percentage of the sisal fiber were also determined. The thermal conductivity of the composites was higher than the pure polyurethane foam, the addition of nonwoven sisal fibers will become in a higher level of compact foam, reducing empty spaces (cells) of polyurethane, inducing an increase in k value. The apparent density of the composites was higher than pure polyurethane foam. In the results of water absorption tests, was seen a higher absorption percent of the composites, what is related to the presence of sisal fibers which are hygroscopic. From TG/DTG results, with the addition of sisal fibers reduced the strength to thermal degradation of the composites, a higher loss of mass was observed in the temperature band between 200 and 340 °C, related to urethane bonds decomposition and cellulose degradation and its derivatives. About mechanical behavior in compression and flexural, composites presented a better mechanical behavior than the rigid polyurethane foam. An increase in the amount of sisal fibers induces a higher rigidity of the composites. At the thermal behavior tests, the composites were more mechanically and thermally resistant than some materials commonly used for thermal insulation, they present the same or better results. The density of nonwoven sisal fiber had influence over the insulation grade; this means that, an increaser in sisal fiber density helped to retain the heat

Análise de desempenho de um refrigerador de pequeno porte com drop in de refrigerantes hidrocarbonetos

From what was stated in the Montreal Protocol, the researchers and refrigeration industry seek substitutes for synthetic refrigerants -chlorofluorocarbons (CFCs) and HCFCs (HCFC) - that contribute to the depletion of the ozone layer. The phase-out of these substances was started using as one of the replacement alternatives the synthetic fluids based on hydro fluorocarbons (HFCs) that have zero potential depletion of the ozone layer. However, contribute to the process of global warming. HFC refrigerants are greenhouse gases and are part of the group of gases whose emissions must be reduced as the Kyoto Protocol says. The hydrocarbons (HC's), for not contribute to the depletion of the ozone layer, because they have very low global warming potential, and are found abundantly in nature, has been presented as an alternative, and therefore, are being used in new home refrigeration equipment in several countries. In Brazil, due to incipient production of domestic refrigerators using HC's, the transition refrigerants remain on the scene for some years. This dissertation deals with an experimental evaluation of the conduct of a drinking fountain designed to work with HFC (R-134a), operating with a mixture of HC's or isobutane (R-600a) without any modification to the system or the lubricating oil. In the refrigeration laboratory of Federal University of Rio Grande do Norte were installed, in a drinking fountain, temperature and pressure sensors at strategic points in the refrigeration cycle, connected to an acquisition system of computerized data, to enable the mapping and thermodynamics analysis of the device operating with R-134a or with a mixture of HC's or with R-600a. The refrigerator-test operating with the natural fluids (mixture of HC's or R-600a) had a coefficient of performance (COP) lower than the R-134a

Degradação catalítica de polietileno de alta densidade sobre a zeólita HZSM

In last years it has talked a lot about the environment and the plastic waste produced and discarded. In last decades, the increasing development of research to obtain fuel from plastic material, by catalytic degradation, it has become a very attractive looking, as these tailings are discarded to millions worldwide. These materials take a long time to degrade themselves by ways said natural and burning it has not demonstrated a viable alternative due to the toxic products produced during combustion. Such products could bring serious consequences to public health and environment. Therefore, the technique of chemical recycling is presented as a suitable alternative, especially since could be obtain fractions of liquid fuels that can be intended to the petrochemical industry. This work aims to propose alternatives to the use of plastic waste in the production of light petrochemical. Zeolites has been widely used in the study of this process due to its peculiar structural properties and its high acidity. In this work was studied the reaction of catalytic degradation of high-density polyethylene (HDPE) in the presence HZSM-12 zeolites with different acid sites concentrations by thermogravimetry and pyrolysis coupled with GC-MS. The samples of the catalysts were mixed with HDPE in the proportion of 50% in mass and submitted to thermogravimetric analyses in several heating rates. The addition of solids with different acid sites concentrations to HDPE, produced a decrease in the temperature of degradation of the polymer proportional the acidity of the catalyst. These qualitative results were complemented by the data of activation energy obtained through the non-isothermal kinetics model proposed by Vyazovkin. The values of Ea when correlated to the data of surface acidity of the catalysts indicated that there is a exponential decrease of the energy of activation in the reaction of catalytic degradation of HDPE, in function of the concentration of acid sites of the materials. These results indicate that the acidity of the catalyst added to the system is one of the most important properties in the reaction of catalytic degradation of polyethylene

Avaliação da estabilidade térmica e oxidativa dos biodieseis de algodão, girassol, dendê e sebo bovino

The search for new sources of environmentally friendly energy is growing every day. Among these alternative energies, biodiesel is a biofuel that has had prominence in world production. In Brazil, law 11.097, determine that all diesel sold in the country must be made by mixing diesel/biodiesel. The latter called BX, , where X represents the percent volume of biodiesel in the diesel oil, as specified by the ANP. In order to guarantee the quality of biodiesel and its mixtures, the main properties which should be controlled are the thermal and oxidative stability. These properties depend mainly of the chemical composition on the raw materials used to prepare the biodiesel. This dissertation aims to study the overall thermal and oxidative stability of biodiesel derived from cotton seed oil, sunflower oil, palm oil and beef tallow, as well as analyze the properties of the blends made from mineral oil and biodiesel in proportion B10. The main physical-chemical properties of oils and animal fat, their respective B100 and blends were determined. The samples were characterized by infrared and gas chromatography (GC). The study of thermal and oxidative stability were performed by thermogravimetry (TG), pressure differential scanning calorimeter (PDSC) and Rancimat. The obtained biodiesel samples are within the specifications established by ANP Resolution number 7/2008. In addition, all the blends and mineral diesel analyzed presented in conformed withthe ANP Regularion specifications number 15/2006. The obtained results from TG curves data indicated that the cotton biodiesel is the more stable combustible. In the kinetic study, we obtained the following order of apparent activation energy for the samples: biodiesel from palm oil > sunflower biodiesel > tallow biodiesel > cotton biodiesel. In terms of the oxidative stability, the two methods studied showed that biodiesel from palm oil is more stable then the tallow. Within the B100 samples studied only the latter were tound to be within the standard required by ANP resolution N° 7. Testing was carried out according to the EN14112. This higher stability its chemical composition

O desenvolvimento da indústria da reciclagem dos materiais no Brasil: motivação econômica ou benefício ambiental conseguido com a atividade?

A indústria de reciclagem vem se desenvolvendo no Brasil desde o começo dos anos noventa, o que resulta em elevados índices de reciclagem e tecnologia de ponta na reciclagem de alguns materiais. Requisitada como estratégia para a gestão dos resíduos no destino final, a reciclagem possui a particularidade de ser uma atividade econômica bastante rentável. Este artigo analisa os índices da indústria de reciclagem dos materiais no Brasil. Com base nos resultados obtidos através da consulta bibliográfica e dados estatísticos oriundos de fontes primárias e secundárias, conclui-se que a atividade da reciclagem dos materiais no Brasil se presta a satisfazer exclusivamente às demandas econômicas do setor. Neste sentido, a contribuição ambiental da reciclagem perde relevância visto que o crescimento da atividade está condicionado às demandas da cadeia produtiva industrial

Evolução morfodinâmica da região de influência estuarina do Rio Curimataú/RN, com ênfase nas alternativas do ambiente deposicional de manguezal e a integração de geodados em Sig

The estuaries are important investigation zones of the actual morphodynamic and of depositional facies of recent geological history. They are constituted in important receptor means of the coastal area sediments, where the evolutionary processes occur quickly. They are also attractive means for the development of anthropic activities, which in a disordered way interfere in the active processes in the sedimentary balance of the coastal areas. Among the human interventions, the alterations of the depositional environment of mangroves in areas of tropical estuary is deserving relevance, whose implications for the environment estuarine and the coastal adjacent, they are still far to be known. Due to the interest of the sedimentologic component in the comprehension of the processes linked to the evolution of the environments estuarine and coastal adjacent, this work, aimed at the understanding of the morphodynamic coastal phenomena that comprise the region of estuarine influence of the River Curimataú / RN. It was also evaluated in the morphodynamic context the implications due to alterations of the depositional environment of mangrove by anthropic activity. The Curimataú Estuary, located in the south portion of the oriental coast of Rio Grande do Norte, in the last decades has been objective of the overwhelming occupation of the shrimp farm in areas of mangroves, which were implanted with perspectives of development in a short to medium period. On the other hand, the estuary and its region of coastal influence lacks enough information to subsidize the planning and reorganization more effective of the surrounding activities. Thus, it was intended with this work to give a contribution target tothe maintainable use of the coastal resources of this region. A series of studies using data of orbital and acoustic remote sensing, as of sediments sampling, were executed in the gutter of the estuary. The obtained results starting from the interpretation of bathymetric maps, echo sounder graphics and of distribution of sediments made possible the location of the estuary based in morpho-sedimentar criteria. The estuarine tidal flat was dissected in environments of intertidal mangroves, supratidal mangroves and apicuns with base in the integration of data of sensor optic and of radar following by the field control. The adjacent coast that is influenced by the Curimataú estuary, was segmented according to their geomorphologic characteristics, where each segment had a point of observation of the beach morphodynamic, during the period from january/2001 to february/2002. Once every month, beaches profiles, collections of sediments in the beach zones, as measurement of hydrodynamic parameters were executed. The results of the observations of the tidal environment showed that the area of estuarine influence of the Curimataú begins to suffer negative sedimentary taxes, where in some beaches, the erosive processes are already observed. The granulometric characteristics of the beach sediments start to tend for the increase of thin sand in the erosive periods. The destruction of the depositional environments of mangroves of the Curimataú estuary, to the construction of shrimp farms, can be providing the diminution of the tidal prism of the estuary, enlarging the effects of the local increasing of the sea level, through the smaller supplying of sediments to the adjacent coast. Besides this, it was verified the possibility of the sanding of the tidal channel in the margins of the destroyed areas of mangroves, where very high taxes of sedimentation of thin materials were estimated in case of these areas were preserve

Materiais zeolíticos de estrutura MWW: síntese e caracterização

In this paper a synthesis parameters study was conducted in order to optimize the obteinment of MCM-22 (MWW structure) and increase its accessibility, getting higher external surface and generating mesopores. Syntheses with Si / Al = 15 and Si / Al = 50 ratios were performed under static conditions at different temperatures and with seeds induction, which resulted in MCM-22 pure and crystalline (Si / Al ratio = 15) after 3 days and Si / Al = 50 after 11 days. The reduction of hexamethyleneimine content (HMI) was studied in the stirring synthesis and a HMI reduction of 47% was possible through the mother liquor reuse, in addition, a specific area of 481 m² / g has been obtained in the fourth synthesis day. Regarding the increase of accessibility of the MCM-22 zeolite skeins of MCM-22 plates with about 2 μm were obtained, through the use of dissolved silica, addition of seeds, increased temperature and synthesis time of 2 days. A significant value of specific area was found for this material, around 500 m² / g. Also with respect to the increase of MCM-22 accessibility, treatment with oxalic acid concentration of 0.5 mol / L and silanization of proto-zeolitic units resulted in the mesopores formation . Furthermore, silanization still favored reduction of 70 % in crystal size and a specific area of 566 m² / g.

Obtenção, caracterização e utilização de um compósito com matriz de resina poliéster e carga de fibras de sisal

The constant search for sustainable alternatives has earned great effort of researchers in research and obtaining new materials, encouraging the rise of eco-friendly productive development and providing simple and practical solutions to economic profitability. In this sense, the use of materials derived from natural renewable sources, vegetables, has great potential applicability to sustainable development. As alternative materials plant fibers can be applied to production of a range of composite materials easing the use of materials derived from non-renewable this thesis were sisal mats used for achieving a composite matrix having as one orthophthalic polyester resin. The webs were subjected to surface treatment in boiling water for 15 minutes. The webs of sisal fibers used were, respectively, 5%, 10% and 15% of the composite weight. The composite was obtained and characterized mechanically and thermally to the chosen formulations. several plates of the composite to obtain the body of evidence for the characterization tests complying with the relevant rules were made. The obtained composites showed strength tensile and bending lower than the array, so it can be used where are required low load requests. The most significant result of the composite studied given to the impact energy absorption, far superior to the matrix used. Other properties were highlighted in oil absorption, and density. It proved the feasibility of obtaining the composite for the three formulations studied C5, C10 and C15 being the most feasible to C10. To demonstrate the feasibility of using composite were made a wall clock, a bench, a chair and a shelf, low mechanical stress structures. It was concluded that the sisal rugs exercised the load function in the composite.

Obtenção, caracterização e utilização de um compósito com matriz de resina poliéster e carga de fibras de sisal

The constant search for sustainable alternatives has earned great effort of researchers in research and obtaining new materials, encouraging the rise of eco-friendly productive development and providing simple and practical solutions to economic profitability. In this sense, the use of materials derived from natural renewable sources, vegetables, has great potential applicability to sustainable development. As alternative materials plant fibers can be applied to production of a range of composite materials easing the use of materials derived from non-renewable this thesis were sisal mats used for achieving a composite matrix having as one orthophthalic polyester resin. The webs were subjected to surface treatment in boiling water for 15 minutes. The webs of sisal fibers used were, respectively, 5%, 10% and 15% of the composite weight. The composite was obtained and characterized mechanically and thermally to the chosen formulations. several plates of the composite to obtain the body of evidence for the characterization tests complying with the relevant rules were made. The obtained composites showed strength tensile and bending lower than the array, so it can be used where are required low load requests. The most significant result of the composite studied given to the impact energy absorption, far superior to the matrix used. Other properties were highlighted in oil absorption, and density. It proved the feasibility of obtaining the composite for the three formulations studied C5, C10 and C15 being the most feasible to C10. To demonstrate the feasibility of using composite were made a wall clock, a bench, a chair and a shelf, low mechanical stress structures. It was concluded that the sisal rugs exercised the load function in the composite.

Adição de cascalho de perfuração da bacia potiguar em argilas para uso em materiais cerâmicos: influência da concentração e temperatura de queima.

One of waste produced on large scale during the well drilling is the gravel drilling. There are techniques for the treatment of the same, but there isn t consensus on what are the best in terms of economic and environmental. One alternative for disposal of this waste and objective of this paper is the incorporation and immobilization of gravel clay matrix to assess their technological properties. The Raw Materials used were characterized by the following techniques: Chemical Analysis by X-ray fluorescence (XRF), mineralogical analysis by X-ray Diffraction (XRD), Grain Size Analysis (FA) and Thermal Analysis by Thermogravimetry (TG) and thermodiferential (DTA). After characterizing, samples were formulated in the following percentages: 0, 5, 10, 15, 25, 50, 75, 100% (weight) of gravel drilling, then the pieces were pressed, dried (110 ° C) and sintered at temperatures of 850, 950 and 1050 ° C. After sintering, samples were tested for water absorption, linear shrinkage, flexural strength, porosity, density, XRD and test color. The results concluded that the incorporation of gravel drilling is a viable possibility for solid masonry bricks and ceramic blocks manufacture at concentrations and firing temperature described here. Residue incorporation reduces an environmental problem, the cost of raw materials for manufacture of ceramic products