Estudo da secagem do feijão verde (Vigna unguiculata L. Walp) - análise experimental do processo combinado leito fixo/leito de jorro

Green bean is considered as one of most traditional Brazilian Northeast dishes. Green beans drying preliminary experiments show that combine processes, fixed-bed/spouted bed, resulted in dehydrated beans with uniform humidity and the recovery of the beans properties after their rehydration. From this assays was defined an initial humidity suited for the spouted bed process. A fixed-bed pre-drying process until a level of 40% humidity gave the best results. The spouted bed characteristic hydrodynamic curves were presented for different beans loads, where changes in the respective beans physical properties were evidenced during the fluidynamic assay, due simultaneous drying process. One 22 factorial experimental design was carried out with three repetition in the central point, considering as entry variables: drying air velocity and temperature. The response variables were the beans brakeage, water fraction evaporated during 20 and 50 minutes of drying and the humidity ratio. They are presented still the modeling of the drying of the green beans in fine layer in the drier of tray and the modeling of the shrinking of the beans of the drying processes fixed-bed and spouted bed

Extração supercrítica do óleo de linhaça: construção do extrator, estudo de parâmetros de processo, avaliação química e antioxidante do produto

The aim of the present study was to extract vegetable oil from brown linseed (Linum usitatissimum L.), determine fatty acid levels, the antioxidant capacity of the extracted oil and perform a rapid economic assessment of the SFE process in the manufacture of oil. The experiments were conducted in a test bench extractor capable of operating with carbon dioxide and co-solvents, obeying 23 factorial planning with central point in triplicate, and having process yield as response variable and pressure, temperature and percentage of cosolvent as independent variables. The yield (mass of extracted oil/mass of raw material used) ranged from 2.2% to 28.8%, with the best results obtained at 250 bar and 50ºC, using 5% (v/v) ethanol co-solvent. The influence of the variables on extraction kinetics and on the composition of the linseed oil obtained was investigated. The extraction kinetic curves obtained were based on different mathematical models available in the literature. The Martínez et al. (2003) model and the Simple Single Plate (SSP) model discussed by Gaspar et al. (2003) represented the experimental data with the lowest mean square errors (MSE). A manufacturing cost of US$17.85/kgoil was estimated for the production of linseed oil using TECANALYSIS software and the Rosa and Meireles method (2005). To establish comparisons with SFE, conventional extraction tests were conducted with a Soxhlet device using petroleum ether. These tests obtained mean yields of 35.2% for an extraction time of 5h. All the oil samples were sterilized and characterized in terms of their composition in fatty acids (FA) using gas chromatography. The main fatty acids detected were: palmitic (C16:0), stearic (C18:0), oleic (C18:1), linoleic (C18:2n-6) and α-linolenic (C18:3n-3). The FA contents obtained with Soxhlet dif ered from those obtained with SFE, with higher percentages of saturated and monounsaturated FA with the Soxhlet technique using petroleum ether. With respect to α-linolenic content (main component of linseed oil) in the samples, SFE performed better than Soxhlet extraction, obtaining percentages between 51.18% and 52.71%, whereas with Soxhlet extraction it was 47.84%. The antioxidant activity of the oil was assessed in the β-carotene/linoleic acid system. The percentages of inhibition of the oxidative process reached 22.11% for the SFE oil, but only 6.09% for commercial oil (cold pressing), suggesting that the SFE technique better preserves the phenolic compounds present in the seed, which are likely responsible for the antioxidant nature of the oil. In vitro tests with the sample displaying the best antioxidant response were conducted in rat liver homogenate to investigate the inhibition of spontaneous lipid peroxidation or autooxidation of biological tissue. Linseed oil proved to be more efficient than fish oil (used as standard) in decreasing lipid peroxidation in the liver tissue of Wistar rats, yielding similar results to those obtained with the use of BHT (synthetic antioxidant). Inhibitory capacity may be explained by the presence of phenolic compounds with antioxidant activity in the linseed oil. The results obtained indicate the need for more detailed studies, given the importance of linseed oil as one of the greatest sources of ω3 among vegetable oils

Produção de forragem verde em sistema hidropônico usando esgoto tratado

In the urban areas of the cities a larger problem of destiny of effluents of the treatment stations is verified due to the junction of the sewages in great volumes. This way the hidroponic cultive becomes important, for your intensive characteristic, as alternative of reuse. This work presents as objective the improvement of the relation hidric-nutritious of the hidroponic cultive of green forage (FVH) using treaty sewage. The production of forage was with corn (Zea mays L.), using double hybrid AG1051, in the experimental field of the Federal University of Rio Grande do Norte (UFRN), in the city of Natal-RN-Brazil. The treated effluent essentially domestic had origin of anaerobic reactor, type decant-digester of two cameras in series followed by anaerobic filters drowned. The hidroponic experimental system was composed of 08 stonemasons, with limited contours for masonry of drained ceramic brick, measuring each one 2,5 meters in length for 1,0 meter of width, with inclination of 4% (m/m) in the longitudinal sense, leveled carefully, in way to not to allow preferential roads in the flow. These dimensions, the useful area of Isow was of 2 square meters. The stonemasons of cultive were waterproof (found and lateral) with plastic canvas of 200 micres of thickness, in the white color. Controlled the entrance and exit of the effluente in the stonemasons, with cycles of 12,68 minutes, it being water of 1,18 minutes. The treatments were constituted of: T1 - 24 hours/day under it waters with flow of 2 L/min; T2 - 12 hours/day under waters with flow of 4 L/min; T3 - 12 hours/day under waters with flow of 2 L/min; and T4 - 16 hours/day under waters with flow of 3 L/min. There were evaluations of the evapotranspirometric demand, of hidroponic system affluent and effluent seeking to characterize and to monitor physical-chemical parameters as: pH, temperature, Electric Conductivity and Fecal Coliforms. This last one was analyzed to the 11 days after isow (DAS) and to the 14 DAS. The others were analyzed daily. I sow it was accomplished in the dates of February 21, 2007, first experiment, and April 10, 2007, second experiment. The density of Isow was of 2 kg of seeds, germinated before 48 hours, for square meter of stonemason. The statistic delineament was it casual entirely with two repetitions, in two experiments. It was applied Tukey test of average to five percent of probability. The cultivation cycle was of 14 DAS with evapotranspirometric demand maximum, reached by T1, of 67,44 mm/day. The analyzed parameters, as mass of green matter - Kg, productivity-Kg/m2 and reason of production of seed FVH/Kg used in Isow, the best result was presented by T1, obtaining value of up to 19,01 Kg/m2 of cultive. Without significant difference, the T4 presented greats values with 16 hours under cycle of water. The Treatments 2 and 3 with 12 hours under cycle of water, they obtained inferior results to the other Treatments. As treatment system, came efficient in the reduction of the salinity. T1 obtained reduction medium maxim of 62,5%, to the 7 DAS, in the amount of salts that enter in the system in they are absorbed in the cultivation. The cultivation FVH acted reducing the microbiologic load. Significant percentile of reduction they were reached, with up to 90,23% of reduction of Units of Colonies (UFC), constituting, like this, the Hidroponic System as good alternative of treatment of effluents of Reactors of high Efficiency

Obtenção de diesel verde por craqueamento termocatalítico de óleo de buriti (Mauritia flexuosa L.) sobre materiais nanoestruturados do tipo LaSBA-15

In order to obtain a biofuel similar to mineral diesel, lanthanum-incorporated SBA- 15 nanostructured materials, LaSBA-15(pH), with different Si/La molar ratios (75, 50, 25), were synthesized in a two-steps hydrothermal procedure, with pH-adjusting of the synthesis gel at 6, and were used like catalytic solids in the buriti oil thermal catalytic cracking. These solids were characterized by X-ray fluorescence (XRF), powder X-ray diffraction (XRD), thermogravimetric analysis (TG/DTG), infrared spectroscopy (FTIR), nitrogen porosimetry and ethanol dehydration, aiming to active sites identify. Taken together, the analyses indicated that the synthesis method has employed to obtain materials highly ordered mesostructures with large average pore sizes and high surface area, besides suggested that the lanthanum was incorporated in the SBA-15 both into the framework as well as within the mesopores. Catalytic dehydration of ethanol over the LaSBA-15(pH) products has shown that they have weak Lewis acid and basic functionalities, indicative of the presence of lanthanum oxide in these samples, especially on the La75SBA-15(pH) sample, which has presented the highest selectivity to ethylene. The buriti oil thermal and thermal catalytic cracking, realized from the room temperature to 450 ºC in a simple distillation system, has allowed obtaining two liquid fractions, each consisting of two phases, one aqueous and another organic, organic liquid (OL). The OL obtained from first fractions has shown high acid index, even in the thermal catalytic process. One the other hand, OL coming from second ones, called green diesel (GD), have presented low acid index, particularly that one obtained from the thermal catalytic process realized over LaSBA-15(pH) samples. The acid sites presence in these samples, associated to their large average pore sizes and high surface areas, have allowed them, especially the La75SBA-15(pH), to present deoxygenating activity in the buriti oil thermal catalytic cracking, providing an oxygenates content reduction, particularly carboxylic acids, in the GD. Furthermore, the GD comes from the second liquid fraction obtained in the buriti oil thermal catalytic cracking over this latest solid sample has shown hydrocarbons composition and physic-chemical properties similar to that mineral diesel, beyond sulfur content low

Análise de impacto baseada em rastreabilidade de artefatos para linhas de produto de software

Software Product Line (SPL) consists of a software development paradigm, whose main focus is to identify features common and variability among applications in a specific domain. An LPS is designed to attend all products requirements from its product family. These requirements and LPS may have changes over time due to several factors, such as evolution of product requirements, evolution of the market, evolution of SLP process, evolution of the technologies used to develop the products. To handle these changes, LPS should be modified and evolve in order to not become obsolete, and adapt itself to new requirements. The Changes Impact Analysis is an activity that understand and identify what consequences these changes are cause on LPS. Impact Analysis on LPS may be supported by traceability relationships, which identify relationships between artefacts created during all phases of software development. Despite the solutions of change impact analysis based on traceability for software, there is a lack of solutions for assessing the change impact analysis based on traceability for LPS, since existing solutions do not include estimates specific to the artefacts of LPS. Thus, this paper proposes a process of change impact analysis and an tool for assessing the change impact through traceability of artefacts in LPS. For this purpose, we specified a process of change impact analysis that considers artifacts produced during the development of LPS. We have also implemented a tool which allows estimating and identifying artefacts and products of LPS affected from changes in other products, changes in class, changes in features, changes between releases of LPS and artefacts related to changes in core assets and variability. Finally, the results were evaluated through metrics

Avaliação sistemática de abordagens de derivação de produto

Product derivation tools are responsible for automating the development process of software product lines. The configuration knowledge, which is responsible for mapping the problem space to the solution space, plays a fundamental role on product derivation approaches. Each product derivation approach adopts different strategies and techniques to manage the existing variabilities in code assets. There is a lack of empirical studies to analyze these different approaches. This dissertation has the aim of comparing systematically automatic product derivation approaches through of the development of two different empirical studies. The studies are analyzed under two perspectives: (i) qualitative that analyzes the characteristics of approaches using specific criteria; and (ii) quantitative that quantifies specific properties of product derivation artifacts produced for the different approaches. A set of criteria and metrics are also being proposed with the aim of providing support to the qualitative and quantitative analysis. Two software product lines from the web and mobile application domains are targets of our study

Uma abordagem sistemática para implementação, gerenciamento e customização de testes de linhas de produto de software

Through the adoption of the software product line (SPL) approach, several benefits are achieved when compared to the conventional development processes that are based on creating a single software system at a time. The process of developing a SPL differs from traditional software construction, since it has two essential phases: the domain engineering - when common and variables elements of the SPL are defined and implemented; and the application engineering - when one or more applications (specific products) are derived from the reuse of artifacts created in the domain engineering. The test activity is also fundamental and aims to detect defects in the artifacts produced in SPL development. However, the characteristics of an SPL bring new challenges to this activity that must be considered. Several approaches have been recently proposed for the testing process of product lines, but they have been shown limited and have only provided general guidelines. In addition, there is also a lack of tools to support the variability management and customization of automated case tests for SPLs. In this context, this dissertation has the goal of proposing a systematic approach to software product line testing. The approach offers: (i) automated SPL test strategies to be applied in the domain and application engineering, (ii) explicit guidelines to support the implementation and reuse of automated test cases at the unit, integration and system levels in domain and application engineering; and (iii) tooling support for automating the variability management and customization of test cases. The approach is evaluated through its application in a software product line for web systems. The results of this work have shown that the proposed approach can help the developers to deal with the challenges imposed by the characteristics of SPLs during the testing process

Reqsys-MDD: uma ferramenta para mapeamento entre modelos de features e requisitos em linhas de produto de software

The approach Software Product Line (SPL) has become very promising these days, since it allows the production of customized systems on large scale through product families. For the modeling of these families the Features Model is being widely used, however, it is a model that has low level of detail and not may be sufficient to guide the development team of LPS. Thus, it is recommended add the Features Model to other models representing the system from other perspectives. The goals model PL-AOVgraph can assume this role complementary to the Features Model, since it has a to context oriented language of LPS's, which allows the requirements modeling in detail and identification of crosscutting concerns that may arise as result of variability. In order to insert PL-AOVgraph in development of LPS's, this paper proposes a bi-directional mapping between PL-AOVgraph and Features Model, which will be automated by tool ReqSys-MDD. This tool uses the approach of Model-Driven Development (MDD), which allows the construction of systems from high level models through successive transformations. This enables the integration of ReqSys-MDD with other tools MDD that use their output models as input to other transformations. So it is possible keep consistency among the models involved, avoiding loss of informations on transitions between stages of development

Caracterizando os fluxos excepcionais em linhas de produto de software: um estudo exploratório

The Exception Handling (EH) is a widely used mechanism for building robust systems. In Software Product Line (SPL) context it is not different. As EH mechanisms are embedded in most of mainstream programming languages (like Java, C# and C++), we can find exception signalers and handlers spread over code assets associated to common and variable SPL features. When exception signalers and handlers are added to an SPL in an unplanned way, one of the possible consequences is the generation of faulty family instances (i.e., instances on which common or variable features signal exceptions that are mistakenly caught inside the system). In this context, some questions arise: How exceptions flow between the optional and alternative features an LPS? Aiming at providing answers to these questions, this master thesis conducted an exploratory study, based on code inspection and static analysis code, whose goal was to categorize the main ways which exceptions flow in LPSs. To support the study, we developed an static analysis tool called PLEA (Product Line Exception Analyzer) that calculates the exceptional flows of LPSs, and categorize these flows according to the features associated with handlers and signalers. Preliminary results showed that some types of exceptional flows have more potential to yield failures in exceptional behavior of SLPs

Squid impact analyser: uma ferramenta para análise de impacto de mudança em linhas de produto de software

Software Products Lines (SPL) is a software engineering approach to developing software system families that share common features and differ in other features according to the requested software systems. The adoption of the SPL approach can promote several benefits such as cost reduction, product quality, productivity, and time to market. On the other hand, the SPL approach brings new challenges to the software evolution that must be considered. Recent research work has explored and proposed automated approaches based on code analysis and traceability techniques for change impact analysis in the context of SPL development. There are existing limitations concerning these approaches such as the customization of the analysis functionalities to address different strategies for change impact analysis, and the change impact analysis of fine-grained variability. This dissertation proposes a change impact analysis tool for SPL development, called Squid Impact Analyzer. The tool allows the implementation of change impact analysis based on information from variability modeling, mapping of variability to code assets, and existing dependency relationships between code assets. An assessment of the tool is conducted through an experiment that compare the change impact analysis results provided by the tool with real changes applied to several evolution releases from a SPL for media management in mobile devices

Purificação e caracterização estrutural de homogalactanas sulfatadas anticoagulantes da alga verde Codium isthmocladum

Conselho Nacional de Desenvolvimento Científico e Tecnológico

Petrologia do plúton granitico serra verde, porção lestre do domínio seridó

The study area is located at the eastern-central portion of the Seridó Belt, on the interface between the Seridó Group Metasediments and the crystalline basement rocks of the Caicó Complex (RN). Petrographic and geochemical data allow us to define aspects related to the genesis and evolution of the Serra Verde Pluton magmas, which composes the goal of this dissertation The Serra Verde Pluton is a stock with outcropping area of about 25 km², which is intrusive into metasedimentary sequence and the basement gneisses. The pluton intrusion is sintectonic to the Brasiliano event, elongated along the NE direction, developing a cornue geometry. The rock is a monzogranite mainly composed by K-feldspar, plagioclase and quartz, which usually compose more than 85% of the modal analisys. The main mafic mineral is the biotite, while amphibole, sphene, epidote, opaque minerals, allanite, zircon and apatite occur as accessory minerals. It features still a latemagmatic paragenesis composed by chlorite, granular epidote, carbonates and muscovite, developed through the percolation of late CO2 and H2O rich fluids. Chemically, the Serra Verde Pluton rocks may be classified as metaluminous, of calc-alkaline affiliation, sometimes showing trondhjemític characteristics, with high Na2O (>4,5%), Sr (>400ppm) and Ba (>800ppm) and low K2O (≤3,0%), MgO (<1,0%), TiO2 (<0,5%), Rb (<90ppm), Y (≤16ppm) and Zr (≤13ppm). Micropetrographic evidences (mineral assembly and microtextures) indicate that the magma evolution occurred in moderated to high fO2 conditions, above the FMQ buffer. Thermo-barometric data obtained by minor elements geochemistry and the CIPW data, suggest a final/minimal pressure crystallization for the Serra Verde Pluton samples of about 3 to 5 kbar, liquidus temperature around 800o C, solidus temperature between 680o and 660o C. This data is compatible with those observed by many authors for the Neoproterozoic granites of the Seridó Belt. The group of analyzed data (Petrographic, microtextural and geochemical), suggests that the dominant process of the generation and evolution of the Serra Verde Granite magma was the fractional crystallization, probably from basement quartz-dioritic and tonalitic orthogneisses source

Expressão em superfície do sistema de falhas Poço Verde-caraúbas, Bacia Potiguar

The structural knowledge of the western portion of the Potiguar Basin is still in its infancy, especially these related to NW-trending fault systems. This paper analyzes the Poço Verde-Caraúbas Fault System, which was initially recognized in subsurface. The activities involved in this study correspond to remote-sensing analysis and, in particular, to the geometric and kinematic analysis of post-rift sequences of the basin. In addition, the study aimed to determine the stress fields operating in the area. The studies were carried out in an area of 1,000 km², located in the western portion of Potiguar Basin along the Poço Verde-Caraúbas Fault System, Rio Grande do Norte State. The remote sensing imagery indicates a predominance of NW-SE-trending lineaments, consistent with the fault system under study, followed by the NE-SW, N-S and E-W directions. The tectonic structures mapped were analyzed only in outcrops of the Jandaíra Formantion. They are joints (filled or not) in all directions, but with predominance of the NW-trending joints. Faults are usually N-S-trending normal faults and NW-SE and NE-SW-trending strike-slip faults. Geodynamic analysis identified two tectonic stress fields: the first field, "Field 1" is represented by an N-S-trending horizontal compression and E-W-trending horizontal extension. This field affected the Potiguar Basin at least until the Miocene. The second field, "Field 2", is represented by an E-W-trending horizontal compression and N-S-trending horizontal extension. This is the present-day stress field and has affected the Potiguar basin since the Pliocene