Does firefighting foam affect the growth of some Australian native plants?

Firefighting foams (Class A foams) are an effective and widespread firefighting tool, and are frequently used in environmentally sensitive areas. They are known to be ecologically damaging in aquatic environments; however, their impacts at the plant species or ecosystem level are relatively unknown. Reports of shoot damage to plants, suppressed flowering and changes in plant community composition suggest that the environmental damage caused by their use may be unacceptable. Applications of four levels of foam to seedlings of seven Australian plant species, from five representative and widespread families, showed no detectable impacts on a range of vegetative growth characteristics. The results are encouraging for continued use of firefighting foam in sensitive natural habitats.

Compressibility of porous magnesium foam: dependency on porosity and pore size

Mechanical properties of porous magnesium with the porosity of 35–55% and the pore size of about 70–400 μm are investigated by compressive tests focusing on the effects of the porosity and pore size on the Young's modulus and strength. Results indicated that the Young's modulus and peak stress increase with decreasing porosity and pore size. The mechanical properties of the porous magnesium were in a range of those of cancellous bone. Therefore, it is suggested that the porous magnesium is one of promising scaffold materials for hard tissue regeneration.

Does application of firefighting foam affect soil invertebrates?

Firefighting foam (Class A foam) is an effective and widespread frrefighting tool often used in environmentally sensitive areas. Although, firefighting foam is known to be ecologically damaging to aquatic invertebrates, application of 1.0% foam to heathland soils showed no detectable impacts on soil invertebrate orders sampled over several months. The results are encouraging for the continued use of Class A foam as a fire suppression technique in areas with high conservation value.

Novel titanium foam for bone tissue engineering

Titanium foams fabricated by a new powder metallurgical process have bimodal pore distribution architecture (i.e., macropores and micropores), mimicking natural bone. The mechanical properties of the titanium foam with low relative densities of approximately 0.20-0.30 are close to those of human cancellous bone. Also, mechanical properties of the titanium foams with high relative densities of approximately 0.50-0.65 are close to those of human cortical bone. Furthermore, titanium foams exhibit good ability to form a bonelike apatite layer throughout the foams after pretreatment with a simple thermochemical process and then immersion in a simulated body fluid. The present study illustrates the feasibility of using the titanium foams as implant materials in bone tissue engineering applications, highlighting their excellent biomechanical properties and bioactivity.

Crushing simulation of foam-filled aluminium tubes

A numerical study is presented in this paper to investigate the energy absorption of foam-filled aluminium tubes during crushing. The post-buckling mode of the foam-tube structures has been successfully simulated. The predicted compressive load-displacement is in a good agreement with experimental results. The energy absorption ability of the composite structure due to plastic deformation in a crushing process is evaluated by comparison with the tube structure without foam. The results indicate that the energy absorption of a foam-filled tube structure is superior to the tube without foam. The influences of the friction and the geometric parameters of the structure on the energy absorption have also been investigated. Results from this study will assist automotive industry to design crashworthy components based on foam-filled tubes.

Improving the color yield of ink-jet printing on cationized cotton

This study examines the performance of digital ink-jet printing on cationized cotton treated with polyepichlorohydrin-dimethylamine (PECH-amine). The results show that the color yield of ink-jet printing with reactive inks on cationic modified cotton is much greater than that on untreated cotton. The effect on the increase of color yield by cationic modification is greater than that by preparation with alkali, urea, and thickener. The reason for this is that introducing positively charged sites increases dye uptake and dye fixation on cationized cotton. The results also show that cationic modification with PECH-amine decreases the rub fastness but increases the wash fastness of the treated cotton.

Energy absorption and crushing behaviour of foam-filled aluminium tubes

The crushing behaviour and energy absorption of foam filled aluminium tubular structures were investigated using the quasi-static compressive tests. The crushing behaviour of the tubular structures changed due to foam filling. The energy absorption of the foam filled tubular structures was improved significantly. Foam filling caused an interaction effect between the tube and the foam during progressive crushing, leading to an increase in the mean crushing load compared to that of the foam or tube itself. This interaction effect might be affected by several parameters such as the density of the foam, the properties of both the foam material and tube material, and the thickness and outer diameter of the tube. In particular, the interaction effect essentially depended on the ratio of the mean crushing force of the foam to that of the tube.

Surviving suppression : no detectable impacts of Class A foam on soil invertebrates and some Australian native plants

Firefighting foams (Class A foams) are an effective and widespread firefighting tool which are frequently used in environmentally sensitive areas. Firefighting foams are known to be ecologically damaging in aquatic environments, however their impacts at the plant species or ecosystem level are relatively unknown. Reports of shoot damage to plants, suppressed flowering, and changes in plant community composition suggested that the ecological damage caused by their use may be unacceptable. However, applications of foam to seedlings of some Australian plant species from representative and widespread families, showed no detectable impacts on a range of vegetative growth characteristics. Application of 1.0% foam to heathland soils showed no detectable impacts on soil invertebrate Orders sampled over several months. The results are encouraging for the continued use of Class A foam as a fire suppression technique.

Simulation of three-point bending test of titanium foam for biomedical applications

Using Titanium (Ti) foam as an implant material is a new approach for biomedical applications and it is important to understand the mechanical behaviors of this new foam material. In the present study, the bending of the Ti foam has been simulated and compared against recently published data [1]. FE Analysis has been performed by Abaqus software. Stiffness and Yield strength of foams between 50% (cortical bone) to 80% (cancellous bone) porosity range were considered. This study showed that crushable foam material model in Abaqus, which has developed primarily for Aluminum (Al) foam alloys, is also valid for Ti Foam before any crack or damage occurs in the sample.

Mechanical properties of titanium foam for biomedical applications

Understanding the mechanical behaviour of pure titanium (Ti) foam is crucial for the design and development of Ti foam-based load-bearing implants. In this work, pure titanium foam is fabricated by a powder metallurgical process using the space-holder technique with a spacer size of 500 to 800 µm. Experimental data from static compression testing on the Ti foam are presented. The application of theoretical formulae to predict Young's modulus and yield strength of titanium foams is also discussed. A foam with 63% porosity, 87 ± 5 MPa yield strength, and 6.5 ± 1.3 GPa Young's modulus is found to be appropriate for a number of dental and orthopaedic applications.

Yarn setting and hairiness reduction with a steam jet during winding

This paper examines the use of pressurized steam for wrapping and setting the yarn hairs concurrently via a new steam-jet process during winding. Yarn torque can also be stabilized as an added advantage. The results obtained with two batches of pure wool yarns suggest that there is potential to achieve yarn hairiness reduction of up to 60 % with minimum deterioration in hairiness even after subsequent rewinding.

Fabrication of ultrafine powder from eri silk through attritor and jet milling

Fibroin protein derived from silk fibres has been extensively studied with exciting outcomes for a number of potential advanced biomaterial applications. However, one of the major challenges in applications lies in engineering fibroin into a  desired form using a convenient production technology. In this paper, fabrication of ultrafine powder from eri silk is reported. The silk cocoons were degummed and the extracted silk fibres were then chopped into snippets prior to attritor and air jet milling. Effects of process control agents, material load and material to water ratio during attritor milling were studied. Compared to dry and dry–wet attritor milling, wet process emerged as the preferred option as it caused less colour change and facilitated easy handling. Ultrafine silk powder with a volume based particle size d(0.5) of around 700 nm could be prepared following the sequence of chopping ➔ wet attritor milling ➔ spray drying ➔ air jet milling. Unlike most reported powder production methods, this method could fabricate silk particles in a short time without any pre-treatment on degummed fibre. Moreover, the size range obtained is much smaller than that previously produced using standard milling devices. Reduction in fibre tenacity either shortened the milling time even further or helped bypassing media milling to produce fine powder directly through jet milling. However, such reduction in fibre strength did not help in increasing the ultimate particle fineness. The study also revealed that particle density and particle morphology could be manipulated through appropriate changes in the degumming process.

Graphical Abstract:  Fabrication of eri silk powder using attritor and jet milling is reported. Volume based particle size d(0.5) of around 700 nm could be prepared following the sequence chopping ➔ wet attritor milling ➔ spray drying ➔ air jet milling. No pre-treatments were used and the particle size range obtained is much smaller than that previously produced using standard milling devices. Particle density morphology could be manipulated through appropriate changes of cocoon degumming conditions.