The effects of real time control of welding parameters on weld quality in plasma arc keyhole welding

Joints intended for welding frequently show variations in geometry and position, for which it is unfortunately not possible to apply a single set of operating parameters to ensure constant quality. The cause of this difficulty lies in a number of factors, including inaccurate joint preparation and joint fit up, tack welds, as well as thermal distortion of the workpiece. In plasma arc keyhole welding of butt joints, deviations in the gap width may cause weld defects such as an incomplete weld bead, excessive penetration and burn through. Manual adjustment of welding parameters to compensate for variations in the gap width is very difficult, and unsatisfactory weld quality is often obtained. In this study a control system for plasma arc keyhole welding has been developed and used to study the effects of the real time control of welding parameters on gap tolerance during welding of austenitic stainless steel AISI 304L. The welding tests demonstrated the beneficial effect of real time control on weld quality. Compared with welding using constant parameters, the maximum tolerable gap width with an acceptable weld quality was 47% higher when using the real time controlled parameters for a plate thickness of 5 mm. In addition, burn through occurred with significantly larger gap widths when parameters were controlled in real time. Increased gap tolerance enables joints to be prepared and fit up less accurately, saving time and preparation costs for welding. In addition to the control system, a novel technique for back face monitoring is described in this study. The test results showed that the technique could be successfully applied for penetration monitoring when welding non magnetic materials. The results also imply that it is possible to measure the dimensions of the plasma efflux or weld root, and use this information in a feedback control system and, thus, maintain the required weld quality.

On the effects of welding parameters on weld quality of plasma arc keyhole welding of structural steels

The possibility and the usefulness of applying plasma keyhole welding to structural steels with different compositions and material thicknesses, and in various welding positions has been examinated. Single pass butt welding with I groove in flat, horizontal vertical and vertical positions and root welding with V , Y and U grooves of thick plate material in flat position have been studied and the welds with high quality has been obtained. The technological conditions for successful welding are presented. The single and interactive effects of welding parameters on weld quality, especially on surface weld defects, geometrical form errors, internal defects and mechanical properties (strength, ductility, impact toughness, hardness and bendability) of weld joint, are presented. Welding parameter combinations providing the best quality welds are also presented.

Accelerating food safety and quality control: The use of antibody engineering techniques in the detec-tion of low-molecular weight food contaminants

The increased awareness and evolved consumer habits have set more demanding standards for the quality and safety control of food products. The production of foodstuffs which fulfill these standards can be hampered by different low-molecular weight contaminants. Such compounds can consist of, for example residues of antibiotics in animal use or mycotoxins. The extremely small size of the compounds has hindered the development of analytical methods suitable for routine use, and the methods currently in use require expensive instrumentation and qualified personnel to operate them. There is a need for new, cost-efficient and simple assay concepts which can be used for field testing and are capable of processing large sample quantities rapidly. Immunoassays have been considered as the golden standard for such rapid on-site screening methods. The introduction of directed antibody engineering and in vitro display technologies has facilitated the development of novel antibody based methods for the detection of low-molecular weight food contaminants. The primary aim of this study was to generate and engineer antibodies against low-molecular weight compounds found in various foodstuffs. The three antigen groups selected as targets of antibody development cause food safety and quality defects in wide range of products: 1) fluoroquinolones: a family of synthetic broad-spectrum antibacterial drugs used to treat wide range of human and animal infections, 2) deoxynivalenol: type B trichothecene mycotoxin, a widely recognized problem for crops and animal feeds globally, and 3) skatole, or 3-methyindole is one of the two compounds responsible for boar taint, found in the meat of monogastric animals. This study describes the generation and engineering of antibodies with versatile binding properties against low-molecular weight food contaminants, and the consecutive development of immunoassays for the detection of the respective compounds.

Development of a New Welding Product Quality Control and Management System Model for China

The Chinese welding industry is growing every year due to rapid development of the Chinese economy. Increasingly, companies around the world are looking to use Chinese enterprises as their cooperation partners. However, the Chinese welding industry also has its weaknesses, such as relatively low quality and weak management. A modern, advanced welding management system appropriate for local socio-economic conditions is required to enable Chinese enterprises to enhance further their business development. The thesis researches the design and implementation of a new welding quality management system for China. This new system is called ‗welding production quality control management model in China‘ (WQMC). Constructed on the basis of analysis of a survey and in-company interviews, the welding management system comprises the following different elements and perspectives: a ‗Localized congenital existing problem resolution strategies‘ (LCEPRS) database, a ‗human factor designed training system‘ (HFDT) training strategy, the theory of modular design, ISO 3834 requirements, total welding management (TWM), and lean manufacturing (LEAN) theory. The methods used in the research are literature review, questionnaires, interviews, and the author‘s model design experiences and observations, i.e. the approach is primarily qualitative and phenomenological. The thesis describes the design and implementation of a HFDT strategy in Chinese welding companies. Such training is an effective way to increase employees‘ awareness of quality and issues associated with quality assurance. The study identified widely existing problems in the Chinese welding industry and constructed a LCEPRS database that can be used in efforts to mitigate and avoid common problems. The work uses the theory of modular design, TWM and LEAN as tools for the implementation of the WQMC system.

Leimuhitsauksen kokonaisvaltainen laadunhallinta päättymättömässä valssauksessa

Leimuhitsauksen laadunhallinnassa tärkeää on prosessimainen toiminta ja toimintojen kokonaisvaltaisuuden hahmottaminen. Leimuhitsauksen ollessa osana päättymätöntä valssausta hitsauksen laadunhallinta voidaan jakaa kolmeen päävaiheeseen: ennen hitsausta, hitsauksen aikana ja hitsauksen jälkeen vaikuttaviin laaduntuottotekijöihin. Leimuhitsauksen laaduntuottotekijöiden määritys ja jaottelu kaavioiksi on toteutettu tässä työssä. Leimuhitsin tekniseen laatuun vaikuttavat monet ilmiöt ja parametrit hitsauksen aikana. Tärkeimpiä hitsausparametreista ovat hitsausjännite, alustan liikenopeus, tyssäysmatka sekä leimutusaika. Väärät hitsausolosuhteet tai hitsausparametrit aiheuttavat erilaisia mekaanisia ja metallurgisia vikoja leimuhitsiin. Eräs metallurginen vikatyyppi ovat oksidisulkeumat hitsialueella. Nämä hapettuneet alueet voivat johtaa juurensa erilaisista syistä ja esimerkiksi leimutusajan ja epätasaisen liitospinnan yhteyttä sulkeumien syntyyn on epäilty. Pidennetyillä leimutusajoilla tehtyjen hitsauskokeiden ja hitsien rikkovien aineenkoetuskokeiden tuloksena todettiin tässä tutkittujen koehitsien oksidisulkeumien syntyvän hapettumalla leimutuksen aikana tai juuri hetkellä ennen tyssäystä, minkä lisäksi kosteat olosuhteet hitsausatmosfäärin ympärillä heikentävät lopputuloksen laatua. Leimutusajalla on tärkein osa leimutettavia pintoja tasaavana tekijänä ja mitä epätasaisempi liitettävä pinta on, sitä pidemmän leimutusajan se tarvitsee.

Statistical variation of weld profiles and their expected influence on fatigue strength

The general objective of this study was to conduct astatistical analysis on the variation of the weld profiles and their influence on the fatigue strength of the joint. Weld quality with respect to its fatigue strength is of importance which is the main concept behind this thesis. The intention of this study was to establish the influence of weld geometric parameters on the weld quality and fatigue strength. The effect of local geometrical variations of non-load carrying cruciform fillet welded joint under tensile loading wasstudied in this thesis work. Linear Elastic Fracture Mechanics was used to calculate fatigue strength of the cruciform fillet welded joints in as-welded condition and under cyclic tensile loading, for a range of weld geometries. With extreme value statistical analysis and LEFM, an attempt was made to relate the variation of the cruciform weld profiles such as weld angle and weld toe radius to respective FAT classes.

Laivan hitsattujen runkorakenteiden ainettarikkomattoman tarkastuksen ohjauksen ja valvonnan kehittäminen

Laivan rungonvalmistuksen laadunvarmistuksessa käytetään viranomaisten valvomia NDT-tarkastuksia vaatimustenmukaisuuden varmistamiseksi. Yleisimmin käytettävät NDT-tarkastusmenetelmät laivanrakennuksessa ovat visuaali-, röntgen-, ultraääni-, magneettijauhe- ja tunkeumanestetarkastukset. Diplomityön tavoitteena oli kehittää laivan hitsattujen runkorakenteiden ainettarikkomattoman tarkastuksen ohjausta ja valvontaa Aker Finnyards:n Turun telakalla. Työn alussa selvitettiin NDT-tarkastuksen ohjauksen ja valvonnannykytila ja tunnistettiin kehityskohteita. Tutkimusmenetelminä käytettiin työnmittausta ja havainnointitutkimusta. Merkittävimmiksi kehityskohteiksi havaittiinyleinen epätietoisuus NDT-tarkastuksista laivan runkoprosessissa, selkeän NDT-tarkastusten ohjausjärjestelmän puuttuminen sekä puutteellinen valvonta. Kehityskohteiden tunnistamisen perusteella luotiin toimintamalli NDT-tarkastusten ohjauksen ja valvonnan kehittämiseksi. Toimintamallissa on kuvattuna NDT-tarkastusprosessin tekijät ja informaatiovirrat. Toimintamalli on tarvittaessa päivitettävissä.

Kalman Filtering in Online Paper Quality Assessment

Controlling the quality variables (such as basis weight, moisture etc.) is a vital part of making top quality paper or board. In this thesis, an advanced data assimilation tool is applied to the quality control system (QCS) of a paper or board machine. The functionality of the QCS is based on quality observations that are measured with a traversing scanner making a zigzag path. The basic idea is the following: The measured quality variable has to be separated into its machine direction (MD) and cross direction (CD) variations due to the fact that the QCS works separately in MD and CD. Traditionally this is done simply by assuming one scan of the zigzag path to be the CD profile and its mean value to be one point of the MD trend. In this thesis, a more advanced method is introduced. The fundamental idea is to use the signals’ frequency components to represent the variation in both CD and MD. To be able to get to the frequency domain, the Fourier transform is utilized. The frequency domain, that is, the Fourier components are then used as a state vector in a Kalman filter. The Kalman filter is a widely used data assimilation tool to combine noisy observations with a model. The observations here refer to the quality measurements and the model to the Fourier frequency components. By implementing the two dimensional Fourier transform into the Kalman filter, we get an advanced tool for the separation of CD and MD components in total variation or, to be more general, for data assimilation. A piece of a paper roll is analyzed and this tool is applied to model the dataset. As a result, it is clear that the Kalman filter algorithm is able to reconstruct the main features of the dataset from a zigzag path. Although the results are made with a very short sample of paper roll, it seems that this method has great potential to be used later on as a part of the quality control system.

Optimizing of intelligence level in welding

The productivity, quality and cost efficiency of welding work are critical for metal industry today. Welding processes must get more effective and this can be done by mechanization and automation. Those systems are always expensive and they have to pay the investment back. In this case it is really important to optimize the needed intelligence and this way needed automation level, so that a company will get the best profit. This intelligence and automation level was earlier classified in several different ways which are not useful for optimizing the process of automation or mechanization of welding. In this study the intelligence of a welding system is defined in a new way to enable the welding system to produce a weld good enough. In this study a new way is developed to classify and select the internal intelligence level of a welding system needed to produce the weld efficiently. This classification contains the possible need of human work and its effect to the weld and its quality but does not exclude any different welding processes or methods. In this study a totally new way is developed to calculate the best optimization for the needed intelligence level in welding. The target of this optimization is the best possible productivity and quality and still an economically optimized solution for several different cases. This new optimizing method is based on grounds of product type, economical productivity, the batch size of products, quality and criteria of usage. Intelligence classification and optimization were never earlier made by grounds of a made product. Now it is possible to find the best type of welding system needed to welddifferent types of products. This calculation process is a universal way for optimizing needed automation or mechanization level when improving productivity of welding. This study helps the industry to improve productivity, quality and cost efficiency of welding workshops.

Simulating the performance of paper machine control

The topic of this thesis is the simulation of a combination of several control and data assimilation methods, meant to be used for controlling the quality of paper in a paper machine. Paper making is a very complex process and the information obtained from the web is sparse. A paper web scanner can only measure a zig zag path on the web. An assimilation method is needed to process estimates for Machine Direction (MD) and Cross Direction (CD) profiles of the web. Quality control is based on these measurements. There is an increasing need for intelligent methods to assist in data assimilation. The target of this thesis is to study how such intelligent assimilation methods are affecting paper web quality. This work is based on a paper web simulator, which has been developed in the TEKES funded MASI NoTes project. The simulator is a valuable tool in comparing different assimilation methods. The thesis contains the comparison of four different assimilation methods. These data assimilation methods are a first order Bayesian model estimator, an ARMA model based on a higher order Bayesian estimator, a Fourier transform based Kalman filter estimator and a simple block estimator. The last one can be considered to be close to current operational methods. From these methods Bayesian, ARMA and Kalman all seem to have advantages over the commercial one. The Kalman and ARMA estimators seems to be best in overall performance.

The Productivity, Economy and Quality of Welding in the Different Geographical Areas of China - Today and in the Future

This master’s thesis gives out the real situation of the China welding industry and factories nowadays in different geographical areas, in order to inform the Finnish companies who have the willing to find a Chinese welding subcontractor a proper and correct selection concept by analyzing and supplying the information of different scale and form welding factories in different Chinese areas. The first section of this thesis gives out the general situation about the co-operation between China and Finland in the welding industry, also includes the general introduction of the Chinese welding industry. The second section gives out the geographical compartmentalization result of Chinese welding industry, which is where and how many areas will be studied in this thesis. The main body of this thesis is the real information of welding productivity, welding cost, and welding quality in China. All the information was collected from real factories in China by the author. The last section of this thesis is the improvements to the Chinese welding factories that have the willing to become a subcontractor, and the suggestions to the Finnish companies who may find a Chinese welding factory as their subcontractor in future.

Orthogonal function method in modelling paper web quality variation

This work is devoted to the analysis of signal variation of the Cross-Direction and Machine-Direction measurements from paper web. The data that we possess comes from the real paper machine. Goal of the work is to reconstruct the basis weight structure of the paper and to predict its behaviour to the future. The resulting synthetic data is needed for simulation of paper web. The main idea that we used for describing the basis weight variation in the Cross-Direction is Empirical Orthogonal Functions (EOF) algorithm, which is closely related to Principal Component Analysis (PCA) method. Signal forecasting in time is based on Time-Series analysis. Two principal mathematical procedures that we used in the work are Autoregressive-Moving Average (ARMA) modelling and Ornstein–Uhlenbeck (OU) process.

On the impact of rigorous approaches on the quality of development

Software systems are expanding and becoming increasingly present in everyday activities. The constantly evolving society demands that they deliver more functionality, are easy to use and work as expected. All these challenges increase the size and complexity of a system. People may not be aware of a presence of a software system, until it malfunctions or even fails to perform. The concept of being able to depend on the software is particularly significant when it comes to the critical systems. At this point quality of a system is regarded as an essential issue, since any deficiencies may lead to considerable money loss or life endangerment. Traditional development methods may not ensure a sufficiently high level of quality. Formal methods, on the other hand, allow us to achieve a high level of rigour and can be applied to develop a complete system or only a critical part of it. Such techniques, applied during system development starting at early design stages, increase the likelihood of obtaining a system that works as required. However, formal methods are sometimes considered difficult to utilise in traditional developments. Therefore, it is important to make them more accessible and reduce the gap between the formal and traditional development methods. This thesis explores the usability of rigorous approaches by giving an insight into formal designs with the use of graphical notation. The understandability of formal modelling is increased due to a compact representation of the development and related design decisions. The central objective of the thesis is to investigate the impact that rigorous approaches have on quality of developments. This means that it is necessary to establish certain techniques for evaluation of rigorous developments. Since we are studying various development settings and methods, specific measurement plans and a set of metrics need to be created for each setting. Our goal is to provide methods for collecting data and record evidence of the applicability of rigorous approaches. This would support the organisations in making decisions about integration of formal methods into their development processes. It is important to control the software development, especially in its initial stages. Therefore, we focus on the specification and modelling phases, as well as related artefacts, e.g. models. These have significant influence on the quality of a final system. Since application of formal methods may increase the complexity of a system, it may impact its maintainability, and thus quality. Our goal is to leverage quality of a system via metrics and measurements, as well as generic refinement patterns, which are applied to a model and a specification. We argue that they can facilitate the process of creating software systems, by e.g. controlling complexity and providing the modelling guidelines. Moreover, we find them as additional mechanisms for quality control and improvement, also for rigorous approaches. The main contribution of this thesis is to provide the metrics and measurements that help in assessing the impact of rigorous approaches on developments. We establish the techniques for the evaluation of certain aspects of quality, which are based on structural, syntactical and process related characteristics of an early-stage development artefacts, i.e. specifications and models. The presented approaches are applied to various case studies. The results of the investigation are juxtaposed with the perception of domain experts. It is our aspiration to promote measurements as an indispensable part of quality control process and a strategy towards the quality improvement.

Silloitushitsauksen robotisointi

Tämän diplomityön tavoitteena oli tutkia ja selvittää kuormakoneen takarunkorakenteen silloitushitsauksen robotisointia. Työ päätettiin rajata koskemaan vain tiettyä moduulia takarungosta. Työssä kartoitettiin tarvittava laitteisto, selvitettiin runkomoduulin silloitusajat sekä arvioitiin investoinnin kannattavuutta. Silloituksen suorittavan järjestelmän vaatimuksena oli, että sen tulee asettaa osat paikoilleen hitsauskiinnittimeen ja tehdä tarvittavat silloitushitsaukset automaattisesti. Sopivaksi laitteistoksi osoittautui taloudellisuuden ja toiminnallisuuden näkökulmasta yhdestä kappaleenkäsittely- sekä hitsausrobotista muodostuva järjestelmä. Kappaleenkäsittelijän ohjauksessa käytetään konenäköä sekä osien paikannuksessa että laadunvarmistuksessa. Robotit liikkuvat yhteisellä lineaariradalla, jonka rinnalla on kappaleenkäsittelylaitteistoja hitsauskiinnittimineen. Robotisoinnin käyttöönotolla yhden takarungon moduulien kokoonpanoon ja silloitukseen käytettävä aika pienenee alle puoleen manuaaliseen työhön verrattuna. Näin saavutetaan merkittäviä kustannussäästöjä. Lisäksi hitsauskiinnittimet voivat olla verrattain yksinkertaisia manuaalityöhön verrattuna, jolloin myös säästetään työkaluinvestoinneissa. Robotisointiprojektin jatkotoimenpiteitä ovat laajamittaiset tuotantosimulaatiot layoutin, laitteiston sekä työkiertojen tarkaksi määrittämiseksi. Lisäksi itse tuotetta on muokattava paremmin robottisilloitukseen sopivaksi.

Quality assurance of refuse derived fuel with machine vision

This thesis studies the use of machine vision in RDF quality assurance and manufacturing. Currently machine vision is used in recycling and material detection and some commer- cial products are available in the market. In this thesis an on-line machine vision system is proposed for characterizing particle size. The proposed machine vision system is based on the mapping between image segmenta- tion and the ground truth of the particle size. The results shows that the implementation of such machine vision system is feasible.