Chaotic Behaviour of Active Magnetic Bearing System by Time Series Analysis

Chaotic behaviour is one of the hardest problems that can happen in nonlinear dynamical systems with severe nonlinearities. It makes the system's responses unpredictable. It makes the system's responses to behave similar to noise. In some applications it should be avoided. One of the approaches to detect the chaotic behaviour is nding the Lyapunov exponent through examining the dynamical equation of the system. It needs a model of the system. The goal of this study is the diagnosis of chaotic behaviour by just exploring the data (signal) without using any dynamical model of the system. In this work two methods are tested on the time series data collected from AMB (Active Magnetic Bearing) system sensors. The rst method is used to nd the largest Lyapunov exponent by Rosenstein method. The second method is a 0-1 test for identifying chaotic behaviour. These two methods are used to detect if the data is chaotic. By using Rosenstein method it is needed to nd the minimum embedding dimension. To nd the minimum embedding dimension Cao method is used. Cao method does not give just the minimum embedding dimension, it also gives the order of the nonlinear dynamical equation of the system and also it shows how the system's signals are corrupted with noise. At the end of this research a test called runs test is introduced to show that the data is not excessively noisy.

Genesis and Evolution of Brittle Structures In Southwestern Finland and Western South Africa. Insights into Fault Reactivation, Fluid Flow and Structural Maturity in Precambrian Cratons

The bedrock of old crystalline cratons is characteristically saturated with brittle structures formed during successive superimposed episodes of deformation and under varying stress regimes. As a result, the crust effectively deforms through the reactivation of pre-existing structures rather than by through the activation, or generation, of new ones, and is said to be in a state of 'structural maturity'. By combining data from Olkiluoto Island, southwestern Finland, which has been investigated as the potential site of a deep geological repository for high-level nuclear waste, with observations from southern Sweden, it can be concluded that the southern part of the Svecofennian shield had already attained structural maturity during the Mesoproterozoic era. This indicates that the phase of activation of the crust, i.e. the time interval during which new fractures were generated, was brief in comparison to the subsequent reactivation phase. Structural maturity of the bedrock was also attained relatively rapidly in Namaqualand, western South Africa, after the formation of first brittle structures during Neoproterozoic time. Subsequent brittle deformation in Namaqualand was controlled by the reactivation of pre-existing strike-slip faults.In such settings, seismic events are likely to occur through reactivation of pre-existing zones that are favourably oriented with respect to prevailing stresses. In Namaqualand, this is shown for present day seismicity by slip tendency analysis, and at Olkiluoto, for a Neoproterozoic earthquake reactivating a Mesoproterozoic fault. By combining detailed field observations with the results of paleostress inversions and relative and absolute time constraints, seven distinctm superimposed paleostress regimes have been recognized in the Olkiluoto region. From oldest to youngest these are: (1) NW-SE to NNW-SSE transpression, which prevailed soon after 1.75 Ga, when the crust had sufficiently cooled down to allow brittle deformation to occur. During this phase conjugate NNW-SSE and NE-SW striking strike-slip faults were active simultaneous with reactivation of SE-dipping low-angle shear zones and foliation planes. This was followed by (2) N-S to NE-SW transpression, which caused partial reactivation of structures formed in the first event; (3) NW-SE extension during the Gothian orogeny and at the time of rapakivi magmatism and intrusion of diabase dikes; (4) NE-SW transtension that occurred between 1.60 and 1.30 Ga and which also formed the NW-SE-trending Satakunta graben located some 20 km north of Olkiluoto. Greisen-type veins also formed during this phase. (5) NE-SW compression that postdates both the formation of the 1.56 Ga rapakivi granites and 1.27 Ga olivine diabases of the region; (6) E-W transpression during the early stages of the Mesoproterozoic Sveconorwegian orogeny and which also predated (7) almost coaxial E-W extension attributed to the collapse of the Sveconorwegian orogeny. The kinematic analysis of fracture systems in crystalline bedrock also provides a robust framework for evaluating fluid-rock interaction in the brittle regime; this is essential in assessment of bedrock integrity for numerous geo-engineering applications, including groundwater management, transient or permanent CO2 storage and site investigations for permanent waste disposal. Investigations at Olkiluoto revealed that fluid flow along fractures is coupled with low normal tractions due to in-situ stresses and thus deviates from the generally accepted critically stressed fracture concept, where fluid flow is concentrated on fractures on the verge of failure. The difference is linked to the shallow conditions of Olkiluoto - due to the low differential stresses inherent at shallow depths, fracture activation and fluid flow is controlled by dilation due to low normal tractions. At deeper settings, however, fluid flow is controlled by fracture criticality caused by large differential stress, which drives shear deformation instead of dilation.

Effects of algal turbidity on foraging and antipredator behaviour of the three-spined stickleback (Gasterosteus aculeatus)

The aim of this thesis was to examine how aquatic organisms, such as fish, behave in an altered environmental condition. Many species of fish use vision as their primary tool to gain information about their surrounding environment. The visual conditions of aquatic habitats are often altered as a result of anthropogenic disturbance, such as eutrophication that initiates algal turbidity. In general, turbidity reduces the visibility and can be hypothesized to have an influence on the behaviour of fish. I used the three-spined stickleback (Gasterosteus aculeatus) as a model species and conducted four studies in the laboratory to test how algal turbidity affects its behaviour. In this thesis, two major behavioural aspects are discussed. The first is antipredator behaviour. In study I, the combined effects of turbidity and shoot density on habitat choice (shelter vs open) behaviour was tested on a group of sticklebacks (20 fish) in the presence and absence of piscivorous perch (Perca fluviatilis). In study II, I examined the behavioural responses of feeding sticklebacks when they were exposed to the sudden appearance of an avian predator (the silhouette of a common tern, Sterna hirundo). The study was done in turbid and clear water using three different groups sizes (1, 3 and 6 fish). The second aspect is foraging behaviour. Study III & IV focused on the effects of algal turbidity on the foraging performance of sticklebacks. In study III, I conducted two separate experiments to examine the effects of turbidity on prey consumption and prey choice of sticklebacks. In this experiment turbidity levels and the proportion of large and small prey (Daphnia spp.) were manipulated. In study IV, I studied whether a group of six sticklebacks can distribute themselves according to food input at two feeding stations in a way that provided each fish with the same amount of food in clear and turbid water. I also observed whether the fish can follow changes in resource distribution between the foraging patches. My results indicate an overall influence of algal turbidity on the antipredator and foraging behaviour of sticklebacks. In the presence of a potential predator, the use of the sheltered habitat was more pronounced at higher turbidity. Besides this, sticklebacks reduced their activity levels with predator presence at higher turbidity and shoot density levels, suggesting a possible antipredator adaptation to avoid a predator. When exposed to a sudden appearance of an avian predator, sticklebacks showed a weaker antipredator response in turbid water, which suggests that turbidity degrades the risk assessment capabilities of sticklebacks. I found an effect of group size but not turbidity in the proportion of sticklebacks that fled to the shelter area, which indicates that sticklebacks are able to communicate among group members at the experimental turbidity levels. I found an overall negative effect of turbidity on food intake. Both turbidity and changes in the proportion of prey sizes played a significant role in a stickleback’s prey selection. At lower turbidity levels (clear <1 and 5 NTU) sticklebacks showed preferences for large prey, whereas in more turbid conditions and when the proportion of large to small prey increased sticklebacks became increasingly random in their prey selection. Finally, my results showed that groups of sticklebacks disperse themselves between feeding stations according to the reward ratios following the predictions of the ideal free distribution theory. However, they took a significantly longer time to reach the equilibrium distribution in turbid water than in clear water. In addition, they showed a slower response to changes in resource distribution in a turbid environment. These findings suggest that turbidity interferes with the information transfer among group foragers. It is important to understand that aquatic animals are often exposed to a degraded environment. The findings of this thesis suggest that algal turbidity negatively affects their behavioural performance. The results also shed light on the underlying behavioural strategies of sticklebacks in turbid conditions that might help them adapt to an altered environmental situation and increase their survival. In conclusion, I hold that although algal turbidity has detrimental effects on the antipredator and foraging behaviour of sticklebacks, their behavioural adjustment might help them adapt to a changing environment.

Elongation behaviour of elastic stitch types in household sewing machines: stretch-stitches versus serger overlock stitces

Lectio praecursoria

Time consumption analysis of the mechanized cut-to-length harvesting system

[Abstract]

Time-Varying Benefits of International Diversification for Finnish Investor: Country-Specific Strategy Concentrating on Emerging Markets

The main objective of this study is to investigate whether the Finnish investors’ country-specific strategy concentrating on emerging markets provides diversification benefits. We also analyze whether the benefits of international diversification has been diminished after periods of high volatility caused by different market crisis. The objective is investigated with three methods: Correlation coefficients, rolling correlations added with OLS trend-lines and Box’s M statistic. All the empirical tests are analyzed and calculated with logarithmic returns of weekly time series data from Friday closing values between January 1995 and December 2007. The number of weekly observations is 678. The data type is total return indices of different countries. Data is collected from DataStream and provided by Datastream Financial. Countries investigated are Finland, Argentina, Brazil, Chile, China, India, Mexico, Poland, Russia, South Africa, South Korea, Thailand and Turkey. The current data is quoted both in U.S. Dollars and local currencies. The empirical results of this thesis show that the correlation coefficients are time-varying across Finland and 12 emerging market countries. Although the correlations have risen from 1995 to 2007, there can be found sub-periods where the correlation has declined from earlier period. The results also indicate that a Finnish investor constructing a portfolio of emerging market countries cannot rely on the correlation coefficients estimated from historical data because of the instability of correlation matrices.

Determination of compression behaviour of coating layer

The strength properties of paper coating layer are very important in converting and printing operations. Too great or low strength of the coating can affect several problems in printing. One of the problems caused by the strength of coating is the cracking at the fold. After printing the paper is folded to final form and the pages are stapled together. In folding the paper coating can crack causing aesthetic damage over printed image or in the worst case the centre sheet can fall off in stapling. When folding the paper other side undergoes tensile stresses and the other side compressive stresses. If the difference between these stresses is too high, the coating can crack on the folding. To better predict and prevent cracking at the fold it is good to know the strength properties of coating layer. It has measured earlier the tensile strength of coating layer but not the compressive strength. In this study it was tried to find some way to measure the compressive strength of the coating layer and investigate how different coatings behave in compression. It was used the short span crush test, which is used to measure the in-plane compressive strength of paperboards, to measure the compressive strength of the coating layer. In this method the free span of the specimen is very small which prevent buckling. It was measured the compressive strength of free coating films as well as coated paper. It was also measured the tensile strength and the Bendtsen air permeance of the coating film. The results showed that the shape of pigment has a great effect to the strength of coating. Platy pigment gave much better strength than round or needle-like pigment. On the other hand calcined kaolin, which is also platy but the particles are aggregated, decreased the strength substantially. The difference in the strength can be explained with packing of the particles which is affecting to the porosity and thus to the strength. The platy kaolin packs up much better than others and creates less porous structure. The results also showed that the binder properties have a great effect to the compressive strength of coating layer. The amount of latex and the glass transition temperature, Tg, affect to the strength. As the amount of latex is increasing, the strength of coating is increasing also. Larger amount of latex is binding the pigment particles better together and decreasing the porosity. Compressive strength was increasing when the Tg was increasing because the hard latex gives a stiffer and less elastic film than soft latex.

Reactive dissolution of sedimentary rocks in flue gas desulfurization : modeling and experimental investigation

Svavel förekommer i kol och olja och oxideras vid förbränning till svaveldioxid (SO2). Årligen utsläpps stora mängder svaveldioxid som åstadkommer sura regn, minskning av stratosfäriskt ozon och sjukdomar. Av dessa orsaker är det nödvändigt att minska utsläppen av svaveldioxid. Den teknologi som rör planering av reaktorer och processer för rökgasavsvavling (FGD) har utvecklats kraftigt och idag använder man olika typer av lösningar. De vanligaste alternativen för FGD är våtskrubber- och semitorra skrubbersystem (Spray Dry Scrubbers, SDS) och injektionsprocesser för absorbenter. SDS-processer har studerats bland annat av Ahlbeck [4] och Klingspor [5] och injektionsprocesser av Alvfors [6]. Kalksten, som i huvusak består av kalciumkarbonat, används i rökgasavsvavling på grund av sin förmåga att binda svavel i form av sulfatsalter. Den vanligaste rökgasavsvavlingsmetoden är våtskrubbning, där det sedimentära stenmaterialets upplösningshastighet är en av de faktorer som påverkar resultatet mest. Utvärdering av kalkstensreaktivitet är därför speciellt viktig vid planering och drift av anläggningar för rökgasavsvavling. Målsättningen med detta arbete var att modellera upplösningen av olika typers kalksten för att få en kvantitativ utvärdering av kvaliteten på de analyserade proverna. Därtill testades även karbonatbiprodukter från stålindustrin för att utvärdera möjligheter att använda andra råmaterial. Det transienta förloppet har analyserats, varvid upplösningshastigheten modellerades bl.a. i avseende på tid och pH. Under arbetets gång har antalet empiriska korrelationer minskats till fördel för fysikaliska modeller av diffusiva och konvektiva masstransportfenomen. En målsättning var att skapa en effektiv och snabb metod för att testa olika absorbenter för rökgasavsvavling under transienta förlopp. I arbetet användes PSD-analys, gjordes pH-mätningar och andra utvärderingar av de fysikaliska parametrar som ingår i beräkningarna. On-line mätningar för de icke-stationära variablerna tid och pH ger möjlighet att eliminera osäkerheter. Vissa modeller kan vara komplicerade. En modell för upplösningshastigheten med mer detaljerad utvärdering av parametrar och färre approximationer är därför nödvändig då man vill utvärdera reaktionshastigheten för fasta partiklar i sur miljö. Arbetet utfördes under fyra år och fem peer review-artiklar ingår i avhandlingen.

Social capital, coping and information behaviour of long-term unemployed people in Finland

Avhandlingen studerar hur långtidsarbetslösa klarar av sin situation, hurdant socialt kapital och informationsbeteende de har, samt granskar hur de ovannämnda faktorerna är relaterade till varandra. Därtill undersöks om det finns skillnader mellan finsk- och svenskspråkiga långtidsarbetslösa på de här tre livsområdena. I undersökningen består socialt kapital av sociala relationer, deltagande i organisatoriska aktiviteter samt känslan av tillhörighet med olika grupper och samfund. Gällande informationsbeteende är fokus på vardaglig informationssökning, vilka källor som används, och hurdana problem man stöter på när man söker information. Som mest påfrestande upplevdes arbetslösheten av män, som var i början eller mitten av sin arbetskarriär. De äldre (över 55 år) verkade på många sätt klara av arbetslöshetssituationen bättre än de yngre, som drabbades hårdare av ekonomiska problem och stress. Kvinnor kunde bättre än män bibehålla en positiv inställning, de hade t.ex. starkare sociala nätverk som stöd, medan mäns sociala relationer i högre grad verkade vila på en arbetsgemenskap, som blev allt svagare i och med utdragen arbetslöshet. Yngre män upplevde också ofta att deras hälsa hade försämrats, när den för kvinnor och äldre arbetslösa i genomsnitt blev bättre. När arbetslösas bemästring av arbetslöshetssituationen, sociala relationer och informationssökning granskades, framgick att människor som var aktiva på ett livsområde också var aktiva på andra livsområden. I de flesta fall framkom inte några större skillnader mellan finsk- och svenskspråkiga arbetslösa. Beträffande informationssökning var de upplevda problemen ändå av diametralt motsatt karaktär – för svenskspråkiga åsamkade för lite tillgänglig information ofta problem, medan problemet för de finskspråkiga var att hitta det väsentliga i informationsflödet. Finskspråkiga kände sig också mera fast anknutna till sin boendemiljö och det finska samhället i stort, svenskspråkiga hade däremot i genomsnitt bredare och tätare sociala nätverk.

Frequency-Domain and Wide-Pulse Time-Domain Measurements of Lanthanide Luminescence and Lanthanide-Based Resonance Energy Transfer

Resonance energy transfer (RET) is a non-radiative transfer of the excitation energy from the initially excited luminescent donor to an acceptor. The requirements for the resonance energy transfer are: i) the spectral overlap between the donor emission spectrum and the acceptor absorption spectrum, ii) the close proximity of the donor and the acceptor, and iii) the suitable relative orientations of the donor emission and the acceptor absorption transition dipoles. As a result of the RET process the donor luminescence intensity and the donor lifetime are decreased. If the acceptor is luminescent, a sensitized acceptor emission appears. The rate of RET depends strongly on the donor–acceptor distance (r) and is inversely proportional to r6. The distance dependence of RET is utilized in binding assays. The proximity requirement and the selective detection of the RET-modified emission signal allow homogeneous separation free assays. The term lanthanide-based RET is used when luminescent lanthanide compounds are used as donors. The long luminescence lifetimes, the large Stokes’ shifts and the intense, sharply-spiked emission spectra of the lanthanide donors offer advantages over the conventional organic donor molecules. Both the organic lanthanide chelates and the inorganic up-converting phosphor (UCP) particles have been used as donor labels in the RET based binding assays. In the present work lanthanide luminescence and lanthanide-based resonance energy transfer phenomena were studied. Luminescence lifetime measurements had an essential role in the research. Modular frequency-domain and time-domain luminometers were assembled and used successfully in the lifetime measurements. The frequency-domain luminometer operated in the low frequency domain ( 100 kHz) and utilized a novel dual-phase lock-in detection of the luminescence. One of the studied phenomena was the recently discovered non-overlapping fluorescence resonance energy transfer (nFRET). The studied properties were the distance and temperature dependences of nFRET. The distance dependence was found to deviate from the Förster theory and a clear temperature dependence was observed whereas conventional RET was completely independent of the temperature. Based on the experimental results two thermally activated mechanisms were proposed for the nFRET process. The work with the UCP particles involved the measurement of the luminescence properties of the UCP particles synthesized in our laboratory. The goal of the UCP particle research is to develop UCP donor labels for binding assays. In the present work the effect of the dopant concentrations and the core–shell structure on the total up-conversion luminescence intensity, the red–green emission ratio, and the luminescence lifetime was studied. Also the non-radiative nature of the energy transfer from the UCP particle donors to organic acceptors was demonstrated for the first time in aqueous environment and with a controlled donor–acceptor distance.

Corrosion behaviour of boiler tube materials during combustion of fuels containing Zn and Pb

Många förbränningsanläggningar som bränner utmanande bränslen såsom restfraktioner och avfall råkar ut för problem med ökad korrosion på överhettare och/eller vattenväggar pga. komponenter i bränslena som är korrosiva. För att minimera problemen i avfallseldade pannor hålls ångparametrarna på en relativt låg nivå, vilket drastiskt minskar energiproduktionen. Beläggningarna i avfallseldade pannor består till största delen av element som är förknippade med högtemperaturkorrosion: Cl, S, alkalimetaller, främst K och Na, och tungmetaller som Pb och Zn, och det finns också indikationer av Br-förekomst. Det låga ångtrycket i avfallseldade pannor påverkar också stålrörens temperatur i pannväggarna i eldstaden. I dagens läge hålls temperaturen normalt vid 300-400 °C. Alkalikloridorsakad (KCl, NaCl) högtemperaturkorrosion har inte rapporterats vara relevant vid såpass låga temperaturer, men närvaro av Zn- och Pb-komponenter i beläggningarna har påvisats förorsaka ökad korrosion redan vid 300-400 °C. Vid förbränning kan Zn och Pb reagera med S och Cl och bilda klorider och sulfater i rökgaserna. Dessa tungmetallföreningar är speciellt problematiska pga. de bildar lågsmältande saltblandningar. Dessa lågsmältande gasformiga eller fasta föreningar följer rökgasen och kan sedan fastna eller kondensera på kallare ytor på pannväggar eller överhettare för att sedan bilda aggressiva beläggningar. Tungmetallrika (Pb, Zn) klorider och sulfater ökar risken för korrosion, och effekten förstärks ytterligare vid närvaro av smälta. Motivet med den här studien var att få en bättre insikt i högtemperaturkorrosion förorsakad av Zn och Pb, samt att undersöka och prediktera beteendet och motståndskraften hos några stålkvaliteter som används i överhettare och pannväggar i tungmetallrika förhållanden och höga materialtemperaturer. Omfattande laboratorie-, småskale- och fullskaletest utfördes. Resultaten kan direkt utnyttjas i praktiska applikationer, t.ex. vid materialval, eller vid utveckling av korrosionsmotverkande verktyg för att hitta initierande faktorer och förstå deras effekt på högtemperaturkorrosion.

The bifurcational behaviour of the spatially distributed Rayleigh equation

At the present work the bifurcational behaviour of the solutions of Rayleigh equation and corresponding spatially distributed system is being analysed. The conditions of oscillatory and monotonic loss of stability are obtained. In the case of oscillatory loss of stability, the analysis of linear spectral problem is being performed. For nonlinear problem, recurrent formulas for the general term of the asymptotic approximation of the self-oscillations are found, the stability of the periodic mode is analysed. Lyapunov-Schmidt method is being used for asymptotic approximation. The correlation between periodic solutions of ODE and PDE is being investigated. The influence of the diffusion on the frequency of self-oscillations is being analysed. Several numerical experiments are being performed in order to support theoretical findings.

Modeling of fireside deposit formation in two industrial furnaces

Fireside deposits can be found in many types of utility and industrial furnaces. The deposits in furnaces are problematic because they can reduce heat transfer, block gas paths and cause corrosion. To tackle these problems, it is vital to estimate the influence of deposits on heat transfer, to minimize deposit formation and to optimize deposit removal. It is beneficial to have a good understanding of the mechanisms of fireside deposit formation. Numerical modeling is a powerful tool for investigating the heat transfer in furnaces, and it can provide valuable information for understanding the mechanisms of deposit formation. In addition, a sub-model of deposit formation is generally an essential part of a comprehensive furnace model. This work investigates two specific processes of fireside deposit formation in two industrial furnaces. The first process is the slagging wall found in furnaces with molten deposits running on the wall. A slagging wall model is developed to take into account the two-layer structure of the deposits. With the slagging wall model, the thickness and the surface temperature of the molten deposit layer can be calculated. The slagging wall model is used to predict the surface temperature and the heat transfer to a specific section of a super-heater tube panel with the boundary condition obtained from a Kraft recovery furnace model. The slagging wall model is also incorporated into the computational fluid dynamics (CFD)-based Kraft recovery furnace model and applied on the lower furnace walls. The implementation of the slagging wall model includes a grid simplification scheme. The wall surface temperature calculated with the slagging wall model is used as the heat transfer boundary condition. Simulation of a Kraft recovery furnace is performed, and it is compared with two other cases and measurements. In the two other cases, a uniform wall surface temperature and a wall surface temperature calculated with a char bed burning model are used as the heat transfer boundary conditions. In this particular furnace, the wall surface temperatures from the three cases are similar and are in the correct range of the measurements. Nevertheless, the wall surface temperature profiles with the slagging wall model and the char bed burning model are different because the deposits are represented differently in the two models. In addition, the slagging wall model is proven to be computationally efficient. The second process is deposit formation due to thermophoresis of fine particles to the heat transfer surface. This process is considered in the simulation of a heat recovery boiler of the flash smelting process. In order to determine if the small dust particles stay on the wall, a criterion based on the analysis of forces acting on the particle is applied. Time-dependent simulation of deposit formation in the heat recovery boiler is carried out and the influence of deposits on heat transfer is investigated. The locations prone to deposit formation are also identified in the heat recovery boiler. Modeling of the two processes in the two industrial furnaces enhances the overall understanding of the processes. The sub-models developed in this work can be applied in other similar deposit formation processes with carefully-defined boundary conditions.