Dual light barrier method for six degrees of freedom tool center point calibration of an industrial robot

Tool center point calibration is a known problem in industrial robotics. The major focus of academic research is to enhance the accuracy and repeatability of next generation robots. However, operators of currently available robots are working within the limits of the robot´s repeatability and require calibration methods suitable for these basic applications. This study was conducted in association with Stresstech Oy, which provides solutions for manufacturing quality control. Their sensor, based on the Barkhausen noise effect, requires accurate positioning. The accuracy requirement admits a tool center point calibration problem if measurements are executed with an industrial robot. Multiple possibilities are available in the market for automatic tool center point calibration. Manufacturers provide customized calibrators to most robot types and tools. With the handmade sensors and multiple robot types that Stresstech uses, this would require great deal of labor. This thesis introduces a calibration method that is suitable for all robots which have two digital input ports free. It functions with the traditional method of using a light barrier to detect the tool in the robot coordinate system. However, this method utilizes two parallel light barriers to simultaneously measure and detect the center axis of the tool. Rotations about two axes are defined with the center axis. The last rotation about the Z-axis is calculated for tools that have different width of X- and Y-axes. The results indicate that this method is suitable for calibrating the geometric tool center point of a Barkhausen noise sensor. In the repeatability tests, a standard deviation inside robot repeatability was acquired. The Barkhausen noise signal was also evaluated after recalibration and the results indicate correct calibration. However, future studies should be conducted using a more accurate manipulator, since the method employs the robot itself as a measuring device.

The Cycle Times of Working Capital: Financial Value Chain Analysis Method

Interest towards working capital management increased among practitioners and researchers because the financial crisis of 2008 caused the deterioration of the general financial situation. The importance of managing working capital effectively increased dramatically during the financial crisis. On one hand, companies highlighted the importance of working capital management as part of short-term financial management to overcome funding difficulties. On the other hand, in academia, it has been highlighted the need to analyze working capital management from a wider perspective namely from the value chain perspective. Previously, academic articles mostly discussed working capital management from a company-centered perspective. The objective of this thesis was to put working capital management in a wider and more academic perspective and present case studies of the value chains of industries as instrumental in theoretical contributions and practical contributions as complementary to theoretical contributions and conclusions. The principal assumption of this thesis is that selffinancing of value chains can be established through effective working capital management. Thus, the thesis introduces the financial value chain analysis method which is employed in the empirical studies. The effectiveness of working capital management of the value chains is studied through the cycle time of working capital. The financial value chain analysis method employed in this study is designed for considering value chain level phenomena. This method provides a holistic picture of the value chain through financial figures. It extends the value chain analysis to the industry level. Working capital management is studied by the cash conversion cycle that measures the length (days) of time a company has funds tied up in working capital, starting from the payment of purchases to the supplier and ending when remittance of sales is received from the customers. The working capital management practices employed in the automotive, pulp and paper and information and communication technology industries have been studied in this research project. Additionally, the Finnish pharmaceutical industry is studied to obtain a deeper understanding of the working capital management of the value chain. The results indicate that the cycle time of working capital is constant in the value chain context over time. The cash conversion cycle of automotive, pulp and paper, and ICT industries are on average 70, 60 and 40 days, respectively. The difference is mainly a consequence of the different cycle time of inventories. The financial crisis of 2008 affected the working capital management of the industries similarly. Both the cycle time of accounts receivable and accounts payable increased between 2008 and 2009. The results suggest that the companies of the automotive, pulp and paper and ICT value chains were not able to self-finance. Results do not indicate the improvement of value chains position in regard to working capital management either. The findings suggest that companies operating in the Finnish pharmaceutical industry are interested in developing their own working capital management, but collaboration with the value chain partners is not considered interesting. Competition no longer occurs between individual companies, but between value chains. Therefore the financial value chain analysis method introduced in this thesis has the potential to support value chains in improving their competitiveness.

Opportunities, constraints and constrained opportunities – A study on mothers’ working time patterns in 22 European countries

The aim of this study was to analyse mothers’ working time patterns across 22 European countries. The focus was on three questions: how much mothers prefer to work, how much they actually work, and to what degree their preferred and actual working times are (in)consistent with each other. The focus was on cross-national differences in mothers’ working time patterns, comparison of mothers’ working times to that of childless women and fathers, as well as on individual- and country-level factors that explain the variation between them. In the theoretical background, the departure point was an integrative theoretical approach where the assumption is that there are various kinds of explanations for the differences in mothers’ working time patterns – namely structural, cultural and institutional – , and that these factors are laid in two levels: individual- and country-levels. Data were extracted from the European Social Survey (ESS) 2010 / 2011. The results showed that mothers’ working time patterns, both preferred and actual working times, varied across European countries. Four clusters were formed to illustrate the differences. In the full-time pattern, full-time work was the most important form of work, leaving all other working time forms marginal. The full-time pattern was perceived in terms of preferred working times in Bulgaria and Portugal. In polarised pattern countries, fulltime work was also important, but it was accompanied by a large share of mothers not working at all. In the case of preferred working times, many Eastern and Southern European countries followed it whereas in terms of actual working times it included all Eastern and Southern European countries as well as Finland. The combination pattern was characterised by the importance of long part-time hours and full-time work. It was the preferred working time pattern in the Nordic countries, France, Slovenia, and Spain, but Belgium, Denmark, France, Norway, and Sweden followed it in terms of actual working times. The fourth cluster that described mothers’ working times was called the part-time pattern, and it was illustrated by the prevalence of short and long part-time work. In the case of preferred working times, it was followed in Belgium, Germany, Ireland, the Netherlands and Switzerland. Besides Belgium, the part-time pattern was followed in the same countries in terms of actual working times. The consistency between preferred and actual working times was rather strong in a majority of countries. However, six countries fell under different working time patterns when preferred and actual working times were compared. Comparison of working mothers’, childless women’s, and fathers’ working times showed that differences between these groups were surprisingly small. It was only in part-time pattern countries that working mothers worked significantly shorter hours than working childless women and fathers. Results therefore revealed that when mothers’ working times are under study, an important question regarding the population examined is whether it consists of all mothers or only working mothers. Results moreover supported the use of the integrative theoretical approach when studying mothers’ working time patterns. Results indicate that mothers’ working time patterns in all countries are shaped by various opportunities and constraints, which are comprised of structural, cultural, institutional, and individual-level factors.

Working capital management in the value chain of automotive industry

The objective of this Master’s thesis is to examine working capital management in the automotive industry in years 2006-2008. The study is conducted by the analysis of financial statements. The sample consists of 65 companies that represent different stages in the value chain of automotive industry beginning from raw material suppliers and ending to car dealers. Working capital management is studied by the cash conversion cycle (CCC). The results show that the average CCC of the value chain is 67 days. Car manufacturers had the longest CCC, 106 days, whereas the CCC of oil companies was the shortest, 22 days. The findings suggest that the cycle time of working capital usually follows the cycle time of inventories, since the changes in cycle times of accounts receivable and payable compensate each other. Improvements in working capital management could be achieved by sharing more accurate information in the chain for example about inventory levels and order points of customer. It could also be discussed within the automotive industry, if the long credit periods, which tie up working capital, are really needed. New technologies enable faster payments, which would reduce the cash conversion cycles, improve the profitability of companies, and increase the competitiveness of the value chain. Working capital should not be reduced at the expense of value chain partners, because nowadays the competition is rather between the value chains than between the companies. Similar research design is applied earlier to study working capital management in the value chain of pulp and paper industry. Even if the industries and the structures of the chains differ from each other, results were surprisingly similar. In future research, working capital management in other industries’ value chains could still be studied and compared to previous studies. ICT industry, for example, could be an interesting object.

The effectiveness of short-term literacy skills intervention on children at risk of reading and writing difficulties in Tanzania : a study of grade one children with dynamic assessment approach

The aim of the study was to create and evaluate an intervention programme for Tanzanian children from a low-income area who are at risk of reading and writing difficulties. The learning difficulties, including reading and writing difficulties, are likely to be behind many of the common school problems in Tanzania, but they are not well understood, and research is needed. The design of the study included an identification and intervention phase with follow-up. A group based dynamic assessment approach was used in identifying children at risk of difficulties in reading and writing. The same approach was used in the intervention. The study was a randomized experiment with one experimental and two control groups. For the experimental and the control groups, a total of 96 (46 girls and 50 boys) children from grade one were screened out of 301 children from two schools in a low income urban area of Dar-es-Salaam. One third of the children, the experimental group, participated in an intensive training programme in literacy skills for five weeks, six hours per week, aimed at promoting reading and writing ability, while the children in the control groups had a mathematics and art programme. Follow-up was performed five months after the intervention. The intervention programme and the tests were based on the Zambian BASAT (Basic Skill Assessment Tool, Ketonen & Mulenga, 2003), but the content was drawn from the Kiswahili school curriculum in Tanzania. The main components of the training and testing programme were the same, only differing in content. The training process was different from traditional training in Tanzanian schools in that principles of teaching and training in dynamic assessment were followed. Feedback was the cornerstone of the training and the focus was on supporting the children in exploring knowledge and strategies in performing the tasks. The experimental group improved significantly more (p = .000) than the control groups during the intervention from pre-test to follow-up (repeated measures ANOVA). No differences between the control groups were noticed. The effect was significant on all the measures: phonological awareness, reading skills, writing skills and overall literacy skills. A transfer effect on school marks in Kiswahili and English was found. Following a discussion of the results, suggestions for further research and adaptation of the programme are presented.

The role of advance payments in working capital management and profitability

The objective of this thesis is to study the role of received advance payments in working capital management by creating a new measurement and to study the relationship between advance payments and profitability. The study has been conducted using narrative literature review and quantitative research methods. The research was made analyzing 108 companies listed in Helsinki Stock Exchange. The results indicate that 68 % of the studied companies are receiving advance payments and the average cycle time for received advance payments is 13 days. A new key figure is created to include received advance payments into the calculation of working capital. Received advance payments shorten the working capital cycle, by 13 days, when they are used in the calculation. The role of advance payments is not as significant as the role of receivables and inventories but advance payments may have a larger role than payables if the company is receiving noticeable amounts of advance payments. There are three branches where companies are receiving more advance payments than average companies. The branches are project business and ICT and publishing sectors. There is a negative correlation between profitability and advance payments based on the results of this study.

Impact of reliability of supply on long-term development approaches to electricity distribution networks

The Finnish electricity distribution sector, rural areas in particular, is facing major challenges because of the economic regulation, tightening supply security requirements and the ageing network asset. Therefore, the target in the distribution network planning and asset management is to develop and renovate the networks to meet these challenges in compliance with the regulations in an economically feasible way. Concerning supply security, the new Finnish Electricity Market Act limits the maximum duration of electricity supply interruptions to six hours in urban areas and 36 hours in rural areas. This has a significant impact on distribution network planning, especially in rural areas where the distribution networks typically require extensive modifications and renovations to meet the supply security requirements. This doctoral thesis introduces a methodology to analyse electricity distribution system development. The methodology is based on and combines elements of reliability analysis, asset management and economic regulation. The analysis results can be applied, for instance, to evaluate the development of distribution reliability and to consider actions to meet the tightening regulatory requirements. Thus, the methodology produces information for strategic decision-making so that DSOs can respond to challenges arising in the electricity distribution sector. The key contributions of the thesis are a network renovation concept for rural areas, an analysis to assess supply security, and an evaluation of the effects of economic regulation on the strategic network planning. In addition, the thesis demonstrates how the reliability aspect affects the placement of automation devices and how the reserve power can be arranged in a rural area network.

Stability of Natural Colorants of Plant Origin

In recent years, there have been studies that show a correlation between the hyperactivity of children and use of artificial food additives, including colorants. This has, in part, led to preference of natural products over products with artificial additives. Consumers have also become more aware of health issues. Natural food colorants have many bioactive functions, mainly vitamin A activity of carotenoids and antioxidativity, and therefore they could be more easily accepted by the consumers. However, natural colorant compounds are usually unstable, which restricts their usage. Microencapsulation could be one way to enhance the stability of natural colorant compounds and thus enable better usage for them as food colorants. Microencapsulation is a term used for processes in which the active material is totally enveloped in a coating or capsule, and thus it is separated and protected from the surrounding environment. In addition to protection by the capsule, microencapsulation can also be used to modify solubility and other properties of the encapsulated material, for example, to incorporate fat-soluble compounds into aqueous matrices. The aim of this thesis work was to study the stability of two natural pigments, lutein (carotenoid) and betanin (betalain), and to determine possible ways to enhance their stability with different microencapsulation techniques. Another aim was the extraction of pigments without the use of organic solvents and the development of previously used extraction methods. Stability of pigments in microencapsulated pigment preparations and model foods containing these were studied by measuring the pigment content after storage in different conditions. Preliminary studies on the bioavailability of microencapsulated pigments and sensory evaluation for consumer acceptance of model foods containing microencapsulated pigments were also carried out. Enzyme-assisted oil extraction was used to extract lutein from marigold (Tagetes erecta) flower without organic solvents, and the yield was comparable to solvent extraction of lutein from the same flowers. The effects of temperature, extraction time, and beet:water ratio on extraction efficiency of betanin from red beet (Beta vulgaris) were studied and the optimal conditions for maximum yield and maximum betanin concentration were determined. In both cases, extraction at 40 °C was better than extraction at 80 °C and the extraction for five minutes was as efficient as 15 or 30 minutes. For maximum betanin yield, the beet:water ratio of 1:2 was better, with possibly repeated extraction, but for maximum betanin concentration, a ratio of 1:1 was better. Lutein was incorporated into oil-in-water (o/w) emulsions with a polar oil fraction from oat (Avena sativa) as an emulsifier and mixtures of guar gum and xanthan gum or locust bean gum and xanthan gum as stabilizers to retard creaming. The stability of lutein in these emulsions was quite good, with 77 to 91 percent of lutein being left after storage in the dark at 20 to 22°C for 10 weeks whereas in spray dried emulsions the retention of lutein was 67 to 75 percent. The retention of lutein in oil was also good at 85 percent. Betanin was incorporated into the inner w1 water phase of a water1-in-oil-inwater2 (w1/o/w2) double emulsion with primary w1/o emulsion droplet size of 0.34 μm and secondary w1/o/w2 emulsion droplet size of 5.5 μm and encapsulation efficiency of betanin of 89 percent. In vitro intestinal lipid digestion was performed on the double emulsion, and during the first two hours, coalescence of the inner water phase droplets was observed, and the sizes of the double emulsion droplets increased quickly because of aggregation. This period also corresponded to gradual release of betanin, with a final release of 35 percent. The double emulsion structure was retained throughout the three-hour experiment. Betanin was also spray dried and incorporated into model juices with different pH and dry matter content. Model juices were stored in the dark at -20, 4, 20–24 or 60 °C (accelerated test) for several months. Betanin degraded quite rapidly in all of the samples and higher temperature and a lower pH accelerated degradation. Stability of betanin was much better in the spray dried powder, with practically no degradation during six months of storage in the dark at 20 to 24 °C and good stability also for six months in the dark at 60 °C with 60 percent retention. Consumer acceptance of model juices colored with spray dried betanin was compared with similar model juices colored with anthocyanins or beet extract. Consumers preferred beet extract and anthocyanin colored model juices over juices colored with spray dried betanin. However, spray dried betanin did not impart any off-odors or off-flavors into the model juices contrary to the beet extract. In conclusion, this thesis describes novel solvent-free extraction and encapsulation processes for lutein and betanin from plant sources. Lutein showed good stability in oil and in o/w emulsions, but slightly inferior in spray dried emulsions. In vitro intestinal lipid digestion showed a good stability of w1/o/w2 double emulsion and quite high retention of betanin during digestion. Consumer acceptance of model juices colored with spray dried betanin was not as good as model juices colored with anthocyanins, but addition of betanin to real berry juice could produce better results with mixture of added betanin and natural berry anthocyanins could produce a more acceptable color. Overall, further studies are needed to obtain natural colorants with good stability for the use in food products.