Modeling and Control of the Power Conversion Unit in a Solid Oxide Fuel Cell Environment

In this doctoral thesis, a power conversion unit for a 10 kWsolid oxide fuel cell is modeled, and a suitable control system is designed. The need for research was identified based on an observation that there was no information available about the characteristics of the solid oxide fuel cell from the perspective of power electronics and the control system, and suitable control methods had not previously been studied in the literature. In addition, because of the digital implementation of the control system, the inherent characteristics of the digital system had to be taken into account in the characteristics of the solid oxide fuel cell (SOFC). The characteristics of the solid oxide fuel cell as well the methods for the modeling and control of the DC/DC converter and the grid converter are studied by a literature survey. Based on the survey, the characteristics of the SOFC as an electrical power source are identified, and a solution to the interfacing of the SOFC in distributed generation is proposed. A mathematical model of the power conversion unit is provided, and the control design for the DC/DC converter and the grid converter is made based on the proposed interfacing solution. The limit cycling phenomenon is identified as a source of low-frequency current ripple, which is found to be insignificant when connected to a grid-tied converter. A method to mitigate a second harmonic originating from the grid interface is proposed, and practical considerations of the operation with the solid oxide fuel cell plant are presented. At the theoretical level, the thesis discusses and summarizes the methods to successfully derive a model for a DC/DC converter, a grid converter, and a power conversion unit. The results of this doctoral thesis can also be used in other applications, and the models and methods can be adopted to similar applications such as photovoltaic systems. When comparing the results with the objectives of the doctoral thesis, we may conclude that the objectives set for the work are met. In this doctoral thesis, theoretical and practical guidelines are presented for the successful control design to connect a SOFC-based distributed generation plant to the utility grid.

Understanding Online Game Players' Post-adoption Behavior: an Investigation of Social Network Games in China

Retaining players and re-attracting switching players has long been a central topic for SNG providers with regard to the post-adoption stage of playing an online game. However, there has not been much research which has explored players’ post-adoption behavior by incorporating the continuance intention and the switching intention. In addition, traditional IS continuance theories were mainly developed to investigate users’ continued use of utilitarian IS, and thus they may fall short when trying to explain the continued use of hedonic IS. Furthermore, compared to the richer literature on IS continuance, far too little attention has been paid to IS switching, leading to a dearth of knowledge on the subject, despite the increased incidence of the switching phenomenon in the IS field. By addressing the limitations of prior literature, this study seeks to examine the determinants of SNG players’ two different post-adoption behaviors, including the continuance intention and the switching intention. This study takes a positivist approach and uses survey research method to test five proposed research models based on Unified Theory of Acceptance and Use of Technology 2; Use and Gratification Theory; Push-Pull-Mooring model; Cognitive Dissonance Theory; and a self-developed model respectively with empirical data collected from the SNG players of one of the biggest SNG providers in China. A total of 3919 valid responses and 541 valid responses were used to examine the continuance intention and the switching intention, respectively. SEM is utilized as the data analysis method. The proposed research models are supported by the empirical data. The continuance intention is determined by enjoyment, fantasy, escapism, social interaction, social presence, social influence, achievement and habit. The switching intention is determined by enjoyment, satisfaction, subjective norms, descriptive norms, alternative attractiveness, the need for variety, change experience, and adaptation cost. This study contributes to IS theories in three important ways. Firstly, it shows IS switching should be included in IS post-adoption research together with IS continuance. Secondly, a modern IS is usually multi-functional and SNG players have multiple reasons for using a SNG, thus a player’s beliefs about the hedonic, social and utilitarian perceptions of their continued use of the SNG exert significant effects on the continuance intention. Thirdly, the determinants of the switch ing intention mainly exert push, pull, and mooring effects. Players’ beliefs about their current SNG and the available alternatives, as well as their individual characteristics are all significant determinants of the switching intention. SNG players combine these effects in order to formulate the switching intention. Finally, this study presents limitations and suggestions for future research.

Offering planning with support of roadmapping in project business

Tämän tutkielman tavoitteena on tutkia kuinka roadmapping-tekniikkaa voidaan käyttää tarjonnan suunnittelun tukena uusien tuotteiden valmistamisen yhteydessä. Työ koostuu teoreettisesta ja käytännönläheisestä osasta. Teoreettinen runko on luotu selventämään kuinka tämän hetkisen tutkimus- ja kehitys projektit lopulta muodostavat tulevaisuuden tarjoaman. Menestyksekkään tuotetarjoaman luominen vaatii, sekä uusien teknologioiden kehittämistä, että markkinoilla olevien asiakkaiden tarpeiden ymmärtämistä. Asiakassuuntaisten tuotteiden kehittäminen vaatii toimintaympäristöstä ja asiakasrajapinnasta tulevien signaalien tunnistamista ja niiden ohjaamista tuote- ja teknologia platformeille. Strategia luodaan tukemaan päätöksentekoa prosessin eri vaiheissa. Yrityskohtainen osio koostuu analyysistä, joka on tehty teetetyn kyselyn ja haas-tattelujen pohjalta. Osana analyysia ovat Major project-yksikön tämänhetkinen tarjonnansuunnitteluprosessi, strategian soveltaminen, informaation kerääminen ja priorisointi, portfolionhallinta ja roadmap-tekniikan käyttö. Ratkaisussa on esitet-ty tarjonnan suunnitteluprosessi ja siihen liittyvät kriittiset komponentit. Roadmapping-tekniikkaaon luotu yhdistämään toimintaympäristö, tuotteet ja teknologia toisiinsa. Toimintaympäristö ja tuotteet on yhdistetty myös linked-grids-tekniikan avulla.

Tuotannon kehittäminen aihiotehtaassa

Työn tavoitteena oli kuvata Artowood Oy:ssä toteutettu tuotannon kehittämishanke sekä arvioida sen nykyistä tuotantoa. Lisäksi käsiteltiin yrityksen asemaa alihankintayrityksenä. Teoriaosuudessa verrattiin eri tuotannonohjausteorioita, käsiteltiin tuotannon ajoitukseen liittyviä kysymyksiä sekä paneuduttiin tuotannon kehittämiseen ja laatuun. Johtopäätöksenä, kehitetty tuotannonohjausjärjestelmä on toimiva nykyisissä olosuhteissa, mutta yrityksen kasvaessaon kiinnitettävä enemmän huomiota tuotannon ajoitusongelmien hallintaan. Lisäksi tuotannon laatua on joka tapauksessa kehitettävä. Artowood Oy on käynnistänyt toimenpiteet oman suoran viennin aloittamiseksi, sillä kotimaan markkinat ovat epävakaat kausivaihteluiden ja kiristyneen kilpailun seurauksena. Vientiprojektinonnistuminen on tärkeää, sillä kotimaassa on liian vähän sellaisia asiakkaita, joilla on tarve Artowood Oy:n tuotantoteknologian kannalta riittävän suurille valmistuserille.

Fibre-reinforced composites as root canal posts

Fibre-reinforced composite (FRC) root canal posts are suggested to have biomechanical benefits over traditional metallic posts, but they lack good adhesion to resin composites. The aim of this series of studies was to evaluate the adhesion of individually formed fibre-reinforced composite material to composite resin and dentin, as well as some mechanical properties. Flexural properties were evaluated and compared between individually formed FRC post material and different prefabricated posts. The depth of polymerization of the individually formed FRC post material was evaluated with IR spectrophotometry and microhardness measurements, and compared to that of resin without fibres. Bonding properties of the individually formed FRC post to resin cements and dentin were tested using Pull-out- and Push-out-force tests, evaluated with scanning electron microscopy, and compared to those of prefabricated FRC and metal posts. Load-bearing capacity and microstrain were evaluated and failure mode assessment was made on incisors restored with individually formed FRC posts of different structures and prefabricated posts. The results of these studies show that the individually polymerized and formed FRC post material had higher flexural properties compared to the commercial prefabricated FRC posts. The individually polymerized FRC material showed almost the same degree of conversion after light polymerization as monomer resin without fibres. Moreover, it was found that the individually formed FRC post material with a semiinterpenetrating polymer network (IPN) polymer matrix bonded better to composite resin luting cement, than did the prefabricated posts with a cross-linked polymer matrix. Furthermore, it was found that, contrary to the other posts, there were no adhesive failures between the individually formed FRC posts and composite resin luting cement. This suggests better interfacial adhesion of cements to these posts. Although no differences in load-bearing capacity or microstrain could be seen, the incisors restored with individually formed FRC posts with a hollow structure showed more favourable failures compared to other prefabricated posts. These studies suggest that it is possible to use individually formed FRC material with semi-IPN polymer matrix as root canal post material. They also indicate that there are benefits especially regarding the bonding properties to composite resin and dentin with this material compared to prefabricated FRC post material with a cross-linked matrix. Furthermore, clinically more repairable failures were found with this material compared to those of prefabricated posts.

The design and implementation of a standards-based mobile messaging platform - case WAP Push Proxy Gateway

Tässä diplomityössä perehdytään WAP:in Push -viitekehykseen. WAP-standardit määrittelevät kuinka Internet-tyyppisiä palveluita, joita voidaan käyttää erilaisia mobiileja päätelaiteitteita käyttäen, toteutetaan tehokkaalla ja verkkoteknologiasta riippumattomalla tavalla. WAP pohjautuu Internet:iin, mutta huomioi pienten päätelaitteiden ja mobiiliverkkojen rajoitukset ja erikoisominaisuudet. WAP Push viitekehys määrittelee verkon aloittaman palvelusisällön toimittamisen. Työn teoriaosassa käydään läpi yleinen WAP-arkkitehtuuri ja WAP-protokollapino käyttäen vertailukohtina lanka-Internetin arkkitehtuuria ja protokollapinoa. Edellistä perustana käyttäen tutustaan WAP Push -viitekehykseen. Käytännönosassa kuvataan WAP Push -välityspalvelimen suunnittelu ja kehitystyö. WAP Push -välityspalvelin on keskeinen verkkoelementti WAP Push -viitekehyksessä. WAP Push -välityspalvelin yhdistää Internetin ja mobiiliverkon tavalla, joka piilottaa teknologiaeroavaisuudet Internetissä olevalta palveluntuottajalta.

Kokoonpanon ohjauksen kehittäminen maa- ja metsätalouskoneteollisuudessa

Kehitetään maa- ja metsätalouskoneita valmistavan yrityksen kokoonpanoohjausta imu- ja työntöohjausmenetelmin. Luodaan sopiva järjestelmä toimintaympäristöön.

The Usage of Microsoft Push Notification Service on Mobile Devices

Along with the increasing in demand of mobile computing, Push Notification (PN) is widely used in mobile phones and other devices. PN allows the developer to send messages to the end users even when the client application is not running at the moment. This solves the problem produced by non-supported multi-tasking feature as well as saving battery life. Microsoft Push Notification Service (MPNS) is one solution to use PNs in Windows Phones. The thesis gives the developers an idea of how to use PNs by introducing MPNS, comparing MPNS with other Push Notification Services, usage of different PN types analysis, and PN simulation system implementation.

A Study of African American Vernacular English in Three Novels and Colloquial Finnish in their Translations – The Dark Tower II: The Drawing of the Three, A Time to Kill and Push

Pro gradu -tutkielma käsittelee afroamerikkalaisen puhekielen (African American Vernacular English, AAVE) käyttöä kolmen englanninkielisen romaanin dialogissa ja suomen yleispuhekielen käyttöä romaanien käännöksissä. Tutkimus on pääasiassa kvantitatiivinen ja deskriptiivinen. Romaanit ovat Stephen Kingin The Dark Tower II: The Drawing of the Three (1987) (Musta torni 2, Kolme korttia pakasta 2005, suom. Kari Salminen), John Grishamin A Time to Kill (1989) (On aika tappaa 1994, suom. Kimmo Linkama) ja Sapphiren Push (1996) (Precious – harlemilaistytön tarina 2010, suom. Kristiina Drews). Alkukielisten romaanien osalta Grisham ja Sapphire suosivat lauseopillisia kielenpiirteitä, kun taas King on suosinut äänteellisiä. Sen sijaan käännöksissä piirteistä yleisimpiä ovat äänteelliset ja harvinaisimpia lauseopilliset. Vaikka käännöksissä sanastolliset piirteet ovat taajaan esiintyviä, äänteellisiä piirteitä esiintyy niitä enemmän. Poikkeuksena on On aika tappaa, jossa sanastollisia piirteitä esiintyy enemmän kuin äänteellisiä. Tulos eroaa Sampo Nevalaisen vuonna 2003 tekemästä tutkimuksesta, jossa hän sai selville, että käännöksissä käytetyt piirteet olivat enimmäkseen sanastollisia, kun taas alun perin suomeksi kirjoitetussa kaunokirjallisuudessa puhekielisyyden vaikutelma saatiin aikaan pääasiassa äänteellisin keinoin. Mahdollinen selitys tässä tutkimuksessa havaitulle erolle on se, että kahdessa romaanissa esiintyvä leimallinen AAVEn käyttö on saanut kääntäjät käyttämään samanlaisia strategioita kuin suomalaiset kirjailijat murretta kirjoittaessaan.

Modulation of Signaling Molecules by Human Leucocyte Antigen B27; Special Reference to STAT1

Reactive arthritis (ReA) is an inflammatory joint disease, which belongs to the group of Spondyloarthritis (SpA). It may occur after infections with certain gram-negative bacteria such as Salmonella and Yersinia. SpAs are strongly associated with the human leucocyte antigen (HLA)-B27. Despite active research, the mechanism by which HLA-B27 causes disease susceptibility is still unknown. However, HLA-B27 has a tendency to misfold during assembly. It is possible that the misfolding of HLA-B27 could alter signaling pathways and/or molecules involved in inflammatory response in cells. We have earlier discovered that in HLA-B27-positive cells the interaction between the host and causative bacteria is disturbed. Our recent studies indicate that the expression of HLA-B27 may alter certain signaling molecules by disturbing their activation. The aim of this study was to investigate whether the expression of HLA-B27 disturbs the signaling molecules, especially the phosphorylation of transcription factor STAT1. STAT1 is an important mediator of inflammatory responses. Our results show that the phosphorylation of the STAT1 is significantly altered in HLA-B27-expressing U937 monocytic cells compared with control cells. STAT1 tyrosine 701 is more strongly phosphorylated in HLAB27- expressing cells; whereas the phosphorylation of STAT1 serine 727 is prolonged. Phosphorylation of STAT1 was discovered to be dependent on protein kinase PKR. Furthermore, we found out that the expression of posttranscriptional gene regulator HuR was altered in HLA-B27-expressing cells. We also detected that HLA-B27-positive cells secrete more interleukin 6, which is an important mediator of inflammation. These results help to understand how HLA-B27 may confer susceptibility to SpAs.