The Effect of Operational Disturbances on Reliability and Operation Time Distribution of NCmachine Tools in FMS

This thesis concentrates on studying the operational disturbance behavior of machine tools integrated into FMS. Operational disturbances are short term failures of machine tools which are especially disruptive to unattended or unmanned operation of FMS. The main objective was to examine the effect of operational disturbances on reliability and operation time distribution for machine tools. The theoretical part of the thesis covers the fimdamentals of FMS relating to the subject of this study. The concept of FMS, its benefits and operator's role in FMS operation are reviewed. The importance of reliability is presented. The terms describing the operation time of machine tools are formed by adopting standards and references. The concept of failure and indicators describing reliability and operational performance for machine tools in FMSs are presented. The empirical part of the thesis describes the research methodology which is a combination of automated (ADC) and manual data collection. By using this methodology it is possible to have a complete view of the operation time distribution for studied machine tools. Data collection was carried out in four FMSs consisting of a total of 17 machine tools. Each FMS's basic features and the signals of ADC are described. The indicators describing the reliability and operation time distribution of machine tools were calculated according to collected data. The results showed that operational disturbances have a significant influence on machine tool reliability and operational performance. On average, an operational disturbance occurs every 8,6 hours of operation time and has a down time of 0,53 hours. Operational disturbances cause a 9,4% loss in operation time which is twice the amount of losses caused by technical failures (4,3%). Operational disturbances have a decreasing influence on the utilization rate. A poor operational disturbance behavior decreases the utilization rate. It was found that the features of a part family to be machined and the method technology related to it are defining the operational disturbance behavior of the machine tool. Main causes for operational disturbances were related to material quality variations, tool maintenance, NC program errors, ATC and machine tool control. Operator's role was emphasized. It was found that failure recording activity of the operators correlates with the utilization rate. The more precisely the operators record the failure, the higher is the utilization rate. Also the FMS organizations which record failures more precisely have fewer operational disturbances.

Field Weakening, Parameters and Operation Range of the Permanent Magnet Traction Motors

The main focus of this thesis is to define the field weakening point of permanent magnet synchronous machine with embedded magnets in traction applications. Along with the thesis a modelling program is made to help the designer to define the field weakening point in practical applications. The thesis utilizes the equations based on the current angle. These equations can be derived from the vector diagram of permanent magnet synchronous machine. The design parameters of the machine are: The maximum rotational speed, saliency ratio, maximum induced voltage and characteristic current. The main result of the thesis is finding out the rated rotational speed, from which the field weakening starts. The action of the machine is estimated at a wide speed range and the changes of machine parameters are examined.

The influence of high cable penetration in distribution networks on earth fault currents and the operation of relay protection.

Recent Storms in Nordic countries were a reason of long power outages in huge territories. After these disasters distribution networks' operators faced with a problem how to provide adequate quality of supply in such situation. The decision of utilization cable lines rather than overhead lines were made, which brings new features to distribution networks. The main idea of this work is a complex analysis of medium voltage distribution networks with long cable lines. High value of cable’s specific capacitance and length of lines determine such problems as: high values of earth fault currents, excessive amount of reactive power flow from distribution to transmission network, possibility of a high voltage level at the receiving end of cable feeders. However the core tasks was to estimate functional ability of the earth fault protection and the possibility to utilize simplified formulas for operating setting calculations in this network. In order to provide justify solution or evaluation of mentioned above problems corresponding calculations were made and in order to analyze behavior of relay protection principles PSCAD model of the examined network have been created. Evaluation of the voltage rise in the end of a cable line have educed absence of a dangerous increase in a voltage level, while excessive value of reactive power can be a reason of final penalty according to the Finish regulations. It was proved and calculated that for this networks compensation of earth fault currents should be implemented. In PSCAD models of the electrical grid with isolated neutral, central compensation and hybrid compensation were created. For the network with hybrid compensation methodology which allows to select number and rated power of distributed arc suppression coils have been offered. Based on the obtained results from experiments it was determined that in order to guarantee selective and reliable operation of the relay protection should be utilized hybrid compensation with connection of high-ohmic resistor. Directional and admittance based relay protection were tested under these conditions and advantageous of the novel protection were revealed. However, for electrical grids with extensive cabling necessity of a complex approach to the relay protection were explained and illustrated. Thus, in order to organize reliable earth fault protection is recommended to utilize both intermittent and conventional relay protection with operational settings calculated by the use of simplified formulas.

Value added logistics in supply and demand chains. Smile. Part 1. eBusiness between global company and itslocal sme supplier network

VALOSADE (Value Added Logistics in Supply and Demand Chains) is the research project of Anita Lukka's VALORE (Value Added Logistics Research) research team inLappeenranta University of Technology. VALOSADE is included in ELO (Ebusiness logistics) technology program of Tekes (Finnish Technology Agency). SMILE (SME-sector, Internet applications and Logistical Efficiency) is one of four subprojects of VALOSADE. SMILE research focuses on case network that is composed of small and medium sized mechanical maintenance service providers and global wood processing customers. Basic principle of SMILE study is communication and ebusiness insupply and demand network. This first phase of research concentrates on creating backgrounds for SMILE study and for ebusiness solutions of maintenance case network. The focus is on general trends of ebusiness in supply chains and networksof different industries; total ebusiness system architecture of company networks; ebusiness strategy of company network; information value chain; different factors, which influence on ebusiness solution of company network; and the correlation between ebusiness and competitive advantage. Literature, interviews and benchmarking were used as research methods in this qualitative case study. Networks and end-to-end supply chains are the organizational structures, which can add value for end customer. Information is one of the key factors in these decentralized structures. Because of decentralization of business, information is produced and used in different companies and in different information systems. Information refinement services are needed to manage information flows in company networksbetween different systems. Furthermore, some new solutions like network information systems are utilised in optimising network performance and in standardizingnetwork common processes. Some cases have however indicated, that utilization of ebusiness in decentralized business model is not always a necessity, but value-add of ICT must be defined case-specifically. In the theory part of report, different ebusiness and architecture models are introduced. These models are compared to empirical case data in research results. The biggest difference between theory and empirical data is that models are mainly developed for large-scale companies - not for SMEs. This is due to that implemented network ebusiness solutions are mainly large company centered. Genuine SME network centred ebusiness models are quite rare, and the study in that area has been few in number. Business relationships between customer and their SME suppliers are nowadays concentrated more on collaborative tactical and strategic initiatives besides transaction based operational initiatives. However, ebusiness systems are further mainly based on exchange of operational transactional data. Collaborative ebusiness solutions are in planning or pilot phase in most case companies. Furthermore, many ebusiness solutions are nowadays between two participants, but network and end-to-end supply chain transparency and information systems are quite rare. Transaction volumes, data formats, the types of exchanged information, information criticality,type and duration of business relationship, internal information systems of partners, processes and operation models (e.g. different ordering models) differ among network companies, and furthermore companies are at different stages on networking and ebusiness readiness. Because of former factors, different customer-supplier combinations in network must utilise totally different ebusiness architectures, technologies, systems and standards.

Entry Strategy Issues in the Ophthalmic Industry: Entry Mode, Pricing and Distribution

Maahantulostrategia asettaa yrityksen kansainvälisiä liiketoimintoja ohjaavat tavoitteet, päämäärät, resurssit ja toiminnan suuntaviivat. Tämä diplomityö käsittelee yrityksen maahantulostrategian elementeistä operaatiomuodon valintaa, hinnoittelua ja jakelua. Työssä rakennetaan teoriakehys elementteihin liittyvien päätösten tutkimiseksi lääketeollisuuden ominaispiirteet huomioiden. Lääketeollisuudella on muihin teollisuudenaloihin verrattuna useita erityispiirteitä, joihin työ perehdyttää. Lisäksi työn olennainen osa on selvittää lääketeollisuuden maakohtaisia säädöksiä ja toimintamalleja. Diplomityö on tehty silmäläkkeitä valmistavalle, kehittävälle ja markkinoivalle Santen Oy:lle, joka suunnittelee toimintansa laajentamista Keski- ja Etelä-Euroopan markkinoille. Tässä laajentumisprosessissa ensimmäisenä kohdemaana on Saksa, jonka markkinoille suuntautuvia toimenpiteitä työ tutkii. Teoriakehyksen, markkinoiden ominaispiirteiden sekä useiden erilaisten analyysien pohjalta työn tavoitteena on antaa operaatiomuotoa, tuotteiden hinnoittelua ja jakelua koskevia suosituksia.

The purpose and use of passenger ships in 2058 - Future scenarios generated by the Delphi method

The purpose of the thesis is to generate scenarios of future purposes and of use of ships, suitable for STX Finland Cruise Oy to design and build, over a 50 year time span by applying the Delphi method and an open innovation approach in a future workshop. The scenarios were mapped out with help of two Delphi survey rounds and one future workshop. The number of participants in both surveys and the workshop was some twenty experts in each, representing various fields. On the basis of the first survey round, four different subject areas were selected for analysis: purposes for the use of ships; energy efficiency of cruises and ships; cost efficiency of sea transportation and vacation; and the views and expectations of the customers in the future. As a result of the future workshop, four different themes were established, which were studied further during the second Delphi round. The themes are future service and operation concepts; versatile uses of the space in ships; communication of environmental benefits of ships, future energy solutions and social interaction between passengers onboard. In addition to generating the scenarios, further aim of the thesis is to implement the Delphi method and workshop activity as foresight tools for STX Europe and to produce a chart of a future shipbuilding foresight community to can serve the open innovation processes in the maritime cluster as a whole.

Strike hard, strike sure - Operation Musketeer : British military planning during the Suez Crisis, 1956

Operation Musketeer, a combined joint Anglo-French operation aimed at regaining control of the Suez Canal in 1956, has received much attention from scholars. The most common approach to the crisis has been to examine the political dimension. The political events that led Prime Minister Anthony Eden’s cabinet to decide to use military force against the wishes of their superior American ally and in the face of American economic pressure and a Soviet threat to attack Paris and London with rockets have been analysed thoroughly. This is particularly the case because the ceasefire and eventual withdrawal were an indisputable defeat of British policy in the Middle East. The military operation not only ruined Prime Minister Eden’s career, but it also diminished the prestige of Britain. It was the beginning of the end, some claim. The British Empire would never be the same. As the consequences of using force are generally considered more important than the military operations themselves, very little attention has been paid to the military planning of Operation Musketeer. The difference between the number of publications on Operation Corporate of the Falklands War and Operation Musketeer is striking. Not only has there been little previous research on the military aspects of Musketeer, the conclusions drawn in the existing works have not reached a consensus. Some historians, such as Correlli Barnett, compare Musketeer to the utter failures of the Tudor landings and Gallipoli. Among significant politicians, Winston Churchill, who had retired from the prime ministership only a year before the Suez Crisis, described the operation as “the most ill-conceived and ill-executed imaginable”. Colin McInnes, a well-known author on British defence policy, represents the middle view when he describes the execution as “far from failure”. Finally, some, like Julian Thompson, the Commander of 3 Commando Brigade during the Falklands War, rate the military action itself as being successful. The interpretation of how successful the handling of the Suez Crisis was from the military point of view depends very much on the approach taken and the areas emphasised in the subject. Frequently, military operations are analysed in isolation from other events. The action of a country’s armed forces is separated from the wider context and evaluated without a solid point of comparison. Political consequences are often used as validated criteria, and complicated factors contributing to military performance are ignored. The lack of comprehensive research on the military action has left room for an analysis concentrating on the military side of the crisis.

Structural and operational optimisation : applications in energy systems

In this work mathematical programming models for structural and operational optimisation of energy systems are developed and applied to a selection of energy technology problems. The studied cases are taken from industrial processes and from large regional energy distribution systems. The models are based on Mixed Integer Linear Programming (MILP), Mixed Integer Non-Linear Programming (MINLP) and on a hybrid approach of a combination of Non-Linear Programming (NLP) and Genetic Algorithms (GA). The optimisation of the structure and operation of energy systems in urban regions is treated in the work. Firstly, distributed energy systems (DES) with different energy conversion units and annual variations of consumer heating and electricity demands are considered. Secondly, district cooling systems (DCS) with cooling demands for a large number of consumers are studied, with respect to a long term planning perspective regarding to given predictions of the consumer cooling demand development in a region. The work comprises also the development of applications for heat recovery systems (HRS), where paper machine dryer section HRS is taken as an illustrative example. The heat sources in these systems are moist air streams. Models are developed for different types of equipment price functions. The approach is based on partitioning of the overall temperature range of the system into a number of temperature intervals in order to take into account the strong nonlinearities due to condensation in the heat recovery exchangers. The influence of parameter variations on the solutions of heat recovery systems is analysed firstly by varying cost factors and secondly by varying process parameters. Point-optimal solutions by a fixed parameter approach are compared to robust solutions with given parameter variation ranges. In the work enhanced utilisation of excess heat in heat recovery systems with impingement drying, electricity generation with low grade excess heat and the use of absorption heat transformers to elevate a stream temperature above the excess heat temperature are also studied.

Modular continuous crystallizer: operation, experimental arrangement and identification of process parameters

Crystallization is employed in different industrial processes. The method and operation can differ depending on the nature of the substances involved. The aim of this study is to examine the effect of various operating conditions on the crystal properties in a chemical engineering design window with a focus on ultrasound assisted cooling crystallization. Batch to batch variations, minimal manufacturing steps and faster production times are factors which continuous crystallization seeks to resolve. Continuous processes scale-up is considered straightforward compared to batch processes owing to increase of processing time in the specific reactor. In cooling crystallization process, ultrasound can be used to control the crystal properties. Different model compounds were used to define the suitable process parameters for the modular crystallizer using equal operating conditions in each module. A final temperature of 20oC was employed in all experiments while the operating conditions differed. The studied process parameters and configuration of the crystallizer were manipulated to achieve a continuous operation without crystal clogging along the crystallization path. The results from the continuous experiment were compared with the batch crystallization results and analysed using the Malvern Morphologi G3 instrument to determine the crystal morphology and CSD. The modular crystallizer was operated successfully with three different residence times. At optimal process conditions, a longer residence time gives smaller crystals and narrower CSD. Based on the findings, at a constant initial solution concentration, the residence time had clear influence on crystal properties. The equal supersaturation criterion in each module offered better results compared to other cooling profiles. The combination of continuous crystallization and ultrasound has large potential to overcome clogging, obtain reproducible and narrow CSD, specific crystal morphologies and uniform particle sizes, and exclusion of milling stages in comparison to batch processes.

Computational and Experimental Analysis of Flow Field in the Diffusers of Centrifugal Compressors

Centrifugal compressors are widely used for example in process industry, oil and gas industry, in small gas turbines and turbochargers. In order to achieve lower consumption of energy and operation costs the efficiency of the compressor needs to be improve. In the present work different pinches and low solidity vaned diffusers were utilized in order to improve the efficiency of a medium size centrifugal compressor. In this study, pinch means the decrement of the diffuser flow passage height. First different geometries were analyzed using computational fluid dynamics. The flow solver Finflo was used to solve the flow field. Finflo is a Navier-Stokes solver. The solver is capable to solve compressible, incompressible, steady and unsteady flow fields. Chien's k-e turbulence model was used. One of the numerically investigated pinched diffuser and one low solidity vaned diffuser were studied experimentally. The overall performance of the compressor and the static pressure distribution before and after the diffuser were measured. The flow entering and leaving the diffuser was measured using a three-hole Cobra-probe and Kiel-probes. The pinch and the low solidity vaned diffuser increased the efficiency of the compressor. Highest isentropic efficiency increment obtained was 3\% of the design isentropic efficiency of the original geometry. It was noticed in the numerical results that the pinch made to the hub and the shroud wall was most beneficial to the operation of the compressor. Also the pinch made to the hub was better than the pinchmade to the shroud. The pinch did not affect the operation range of the compressor, but the low solidity vaned diffuser slightly decreased the operation range.The unsteady phenomena in the vaneless diffuser were studied experimentally andnumerically. The unsteady static pressure was measured at the diffuser inlet and outlet, and time-accurate numerical simulation was conducted. The unsteady static pressure showed that most of the pressure variations lay at the passing frequency of every second blade. The pressure variations did not vanish in the diffuser and were visible at the diffuser outlet. However, the amplitude of the pressure variations decreased in the diffuser. The time-accurate calculations showed quite a good agreement with the measured data. Agreement was very good at the design operation point, even though the computational grid was not dense enough inthe volute and in the exit cone. The time-accurate calculation over-predicted the amplitude of the pressure variations at high flow.

Permanent magnet synchronous motor for industrial inverter applications - analysis and design

During the latest few years the need for new motor types has grown, since both high efficiency and an accurate dynamic performance are demanded in industrial applications. For this reason, new effective control systems such as direct torque control (DTC) have been developed. Permanent magnet synchronous motors (PMSM) are well suitable for new adjustable speed AC inverter drives, because their efficiency and power factor are not depending on the pole pair number and speed to the same extent as it is the case in induction motors. Therefore, an induction motor (IM) with a mechanical gearbox can often be replaced with a direct PM motor drive. Space as well as costs will be saved, because the efficiency increases and the cost of maintenance decreases as well. This thesis deals with design criterion, analytical calculation and analysis of the permanent magnet synchronous motor for both sinusoidal air-gap flux density and rectangular air-gapflux density. It is examined how the air-gap flux, flux densities, inductances and torque can be estimated analytically for salient pole and non-salient pole motors. It has been sought by means of analytical calculations for the ultimate construction for machines rotating at relative low 300 rpm to 600 rpm speeds, which are suitable speeds e.g. in Pulp&Paper industry. The calculations are verified by using Finite Element calculations and by measuring of prototype motor. The prototype motor is a 45 kW, 600 rpm PMSM with buried V-magnets, which is a very appropriate construction for high torque motors with a high performance. With the purposebuilt prototype machine it is possible not only to verify the analytical calculations but also to show whether the 600 rpm PMSM can replace the 1500 rpm IM with a gear. It can also be tested if the outer dimensions of the PMSM may be the same as for the IM and if the PMSM in this case can produce a 2.5 fold torque, in consequence of which it may be possible to achieve the same power. The thesis also considers the question how to design a permanent magnet synchronous motor for relatively low speed applications that require a high motor torqueand efficiency as well as bearable costs of permanent magnet materials. It is shown how a selection of different parameters affects the motor properties. Key words: Permanent magnet synchronous motor, PMSM, surface magnets, buried magnets

Gas-liquid mass transfer in bubbly flow: Estimation of mass transfer, bubble size and reactor performance in various applications

Gas-liquid mass transfer is an important issue in the design and operation of many chemical unit operations. Despite its importance, the evaluation of gas-liquid mass transfer is not straightforward due to the complex nature of the phenomena involved. In this thesis gas-liquid mass transfer was evaluated in three different gas-liquid reactors in a traditional way by measuring the volumetric mass transfer coefficient (kLa). The studied reactors were a bubble column with a T-junction two-phase nozzle for gas dispersion, an industrial scale bubble column reactor for the oxidation of tetrahydroanthrahydroquinone and a concurrent downflow structured bed.The main drawback of this approach is that the obtained correlations give only the average volumetric mass transfer coefficient, which is dependent on average conditions. Moreover, the obtained correlations are valid only for the studied geometry and for the chemical system used in the measurements. In principle, a more fundamental approach is to estimate the interfacial area available for mass transfer from bubble size distributions obtained by solution of population balance equations. This approach has been used in this thesis by developing a population balance model for a bubble column together with phenomenological models for bubble breakage and coalescence. The parameters of the bubble breakage rate and coalescence rate models were estimated by comparing the measured and calculated bubble sizes. The coalescence models always have at least one experimental parameter. This is because the bubble coalescence depends on liquid composition in a way which is difficult to evaluate using known physical properties. The coalescence properties of some model solutions were evaluated by measuring the time that a bubble rests at the free liquid-gas interface before coalescing (the so-calledpersistence time or rest time). The measured persistence times range from 10 msup to 15 s depending on the solution. The coalescence was never found to be instantaneous. The bubble oscillates up and down at the interface at least a coupleof times before coalescence takes place. The measured persistence times were compared to coalescence times obtained by parameter fitting using measured bubble size distributions in a bubble column and a bubble column population balance model. For short persistence times, the persistence and coalescence times are in good agreement. For longer persistence times, however, the persistence times are at least an order of magnitude longer than the corresponding coalescence times from parameter fitting. This discrepancy may be attributed to the uncertainties concerning the estimation of energy dissipation rates, collision rates and mechanisms and contact times of the bubbles.

Lajitteluparametrit korkeakappaisessa sellulinjassa

Tutkimustyön tarkoituksena oli selvittää Tainionkosken sellutehtaan vuonna 2001 uudistetun kuitulinjan prosessin vaikutusta kuumajauhatukseen, kuumalajitteluun, pesutulokseen ja hienolajitteluun. Työn tavoitteena oli löytää ja todentaa optimaalinen ajotapa lopputuotteen eli Tainionkosken kartonkitehtaan kartongin kannalta pesussa, kuidutuksessa, kuumalajittelussa ja hienolajittelussa. Ennen kuitulinjan uudistusta kartoitettiin tilanne kuumajauhatuksessa ja kuumalajittelussa ennen prosessimuutoksia. Kartoituksessa havaittiin, että kuumalajittelu ja kuumakuidutus toimivat parhaiten puhtaan jauhatusenergian ollessa n. 18 kWh/ADT, sekä tilavuusmääräisen ja massavirtamääräisen rejektisuhteen ollessa n. 30 %.Uuden pesemön valmistumisen jälkeen tutkittiin kappatason ja energiatason vaikutusta kuumalajitteluun, kuumakuidutukseen ja pesutulokseen. Tutkimuksessa todettiin tikkupitoisuuksien kasvavan kappatason kohoamisen seurauksena. Kuumajauhimen syöttösakeus kasvoi kappatason noustua, koska prosessimittaus ei huomioinut sakeuden kasvua ja tällöin jauhimen laimennusveden määrä jäi liian vähäiseksi. Korkean kapan seurauksena keitosta tulevien suurien partikkelien määrä lisääntyi. Kuumajauhatuksessa korkeampi kappaluku merkitsi hienoaineen lisääntymistä jauhetussa massassa. Tämän seurauksena kuidutetun massan suotautumisvastus kasvoi kappatason kohottua. Uuden prosessin kuumajauhatukseen tuleva massa on jo pesty 4-vaiheisella DD-pesurilla. Puhtaampi massa kuumajauhatuksessa ja kuumalajittelussa on merkinnyt jauhimen tikkureduktion paranemista, mutta samalla kuumalajittimen tikkujen puhdistustehokkuus on heikentynyt. Laboratoriomittausten mukaan kappatason kasvu huonontaa pesutulosta uudessa pesemössä. Uuden hienolajittamon suorituskykyä määritettiin taseiden avulla. Vanhan lajittamon toiminnassa huomattiin puutteita siinä, että 2-portaan lajittimen 1-portaan syöttöön tulevan rejektivirran tikkupitoisuus oli suurempi mitä tikkupitoisuus 1-portaan syöttövirrassa. Uudessa lajittamossa molempien virtausten tikkupitoisuudet olivat lähes samat. Kokonaisuudessaan hienolajittamon toiminta havaittiin hyväksi. Pesemö ja hienolajittelu toimivat kokeiden perusteella parhaiten lähellä mitoitettua maksimituotantoa 700 ADT/d.

Osteoclastic tartrate-resistant acid phosphatase 5b. Diagnostic use and biological significance in bone physiology

The skeleton undergoes continuous turnover throughout life. In women, an increase in bone turnover is pronounced during childhood and puberty and after menopause. Bone turnover can be monitored by measuring biochemical markers of bone resorption and bone formation. Tartrate-resistant acid phosphatase (TRACP) is an enzyme secreted by osteoclasts, macrophages and dendritic cells. The secreted enzyme can be detected from the blood circulation by recently developed immunoassays. In blood circulation, the enzyme exists as two isoforms, TRACP 5a with an intact polypeptide chain and TRACP 5b in which the polypeptide chain consists of two subunits. The 5b form is predominantly secreted by osteoclasts and is thus associated with bone turnover. The secretion of TRACP 5b is not directly related to bone resorption; instead, the levels are shown to be proportional to the number of osteoclasts. Therefore, the combination of TRACP 5b and a marker reflecting bone degradation, such as C-terminal cross-linked telopeptides of type I collagen (CTX), enables a more profound analysis of the changes in bone turnover. In this study, recombinant TRACP 5a-like protein was proteolytically processed into TRACP 5b-like two subunit form. The 5b-like form was more active both as an acid phosphatase and in producing reactive oxygen species, suggesting a possible function for TRACP 5b in osteoclastic bone resorption. Even though both TRACP 5a and 5b were detected in osteoclasts, serum TRACP 5a levels demonstrated no change in response to alendronate treatment of postmenopausal women. However, TRACP 5b levels decreased substantially, demonstrating that alendronate decreases the number of osteoclasts. This was confirmed in human osteoclast cultures, showing that alendronate decreased the number of osteoclats by inducing osteoclast apoptosis, and TRACP 5b was not secreted as an active enzyme from the apoptotic osteoclasts. In peripubertal girls, the highest levels of TRACP 5b and other bone turnover markers were observed at the time of menarche, whereas at the same time the ratio of CTX to TRACP 5b was lowest, indicating the presence of a high number of osteoclasts with decreased resorptive activity. These results support the earlier findings that TRACP 5b is the predominant form of TRACP secreted by osteoclasts. The major source of circulating TRACP 5a remains to be established, but is most likely other cells of the macrophage-monocyte system. The results also suggest that bone turnover can be differentially affected by both osteoclast number and their resorptive activity, and provide further support for the possible clinical use of TRACP 5b as a marker of osteoclast number.

Automatic meter reading – benefits and applications

In liberalized electricity markets, which have taken place in many countries over the world, the electricity distribution companies operate in the competitive conditions. Therefore, accurate information about the customers’ energy consumption plays an essential role for the budget keeping of the distribution company and for correct planning and operation of the distribution network. This master’s thesis is focused on the description of the possible benefits for the electric utilities and residential customers from the automatic meter reading system usage. Major benefits of the AMR, illustrated in the thesis, are distribution network management, power quality monitoring, load modelling, and detection of the illegal usage of the electricity. By the example of the power system state estimation, it was illustrated that even the partial installation of the AMR in the customer side leads to more accurate data about the voltage and power levels in the whole network. The thesis also contains the description of the present situation of the AMR integration in Russia.