Mallinnusinformaation hyödyntäminen ohjelmistokehityksessä

Ohjelmistoprosesseissa kulkee käytännössä sama tieto muuntuen eri vaiheissa käyttökohteensa mukaan. Tätä mallinnusinformaatiota on mahdollista siirtää ja käyttää uudelleen, mikä säästää resursseja ja vähentää riskejä kaikissa projektin vaiheissa. Projektin alussa ohjelmiston toimintoja suunnitellaan ja niitä mallinnetaan esim. UML-malleilla. Tätä mallinnusinformaatiota hallitaan erilaisilla CASE-työkaluilla, joiden avullamalleja on helppo konvertoida toteutusvaihetta varten lähdekoodiksi. Lähdekoodivoidaan tuoda takaisin malliksi jatkosuunnittelua varten, jos työkalu tukee ominaisuutta. Testausvaiheessa lähdekoodi voidaan parsia, jotta siitä saadaan esille olennainen mallinnusinformaatio testejä varten. Lopulta dokumentaatiota voidaan generoida automaattisesti esim. Javadocilla. Mallinnusinformaation hyödyntäminen onnistuu hyvin teoriassa, mutta se ei ole niin suoraviivaista käytännössä. Tämänhetkiset työkalut eivät ole tarpeeksi joustavia mallinnusinformaation palauttamiseksi edellisiin vaiheisiin, joten ne ajavat toteuttamaan projekteja lineaarisesti. Keskikokoisessakin ohjelmistoprojektissa on suuri määrä mallinnusinformaatiota ja se lisää haasteita. Vaikka työkalut ovat kankeita, mallinnusinformaation hyödyntämisen on koettu tehostavan ohjelmistoprosesseja. Siksi sen keinoja tutkitaan ahkerasti.

A Model for Product Transfer Project

In this thesis a model for managing the product data in a product transfer project was created for ABB Machines. This model was then applied for the ongoing product transfer project during its planning phase. Detailed information about the demands and challenges in product transfer projects was acquired by analyzing previous product transfer projects in participating organizations. This analysis and the ABB Gate Model were then used as a base for the creation of the model for managing the product data in a product transfer project. The created model shows the main tasks during each phase in the project, their sub-tasks and relatedness on general level. Furthermore the model emphasizes need for detailed analysis of the situation during the project planning phase. The created model for managing the product data in a product transfer project was applied into ongoing project two main areas; manufacturing instructions and production item data. The results showed that the greatest challenge considering the product transfer project in previously mentioned areas is the current state of the product data. Based on the findings, process and resource proposals for both the ongoing product transfer project and the BU Machines were given. For manufacturing instructions it is necessary to create detailed process instructions in receiving organizations own language for each department so that the manufacturing instructions can be used as a training material during the training in sending organization. For production item data the English version of the bill of materials needs to be fully in English. In addition it needs to be ensured that bill of materials is updated and these changes implemented before the training in sending organization begins.

A Practical Micro Mechanical Model Based Local Approach Methodology for the Analysis of Ductile Fracture of Welded T-Joints

This thesis concentrates on developing a practical local approach methodology based on micro mechanical models for the analysis of ductile fracture of welded joints. Two major problems involved in the local approach, namely the dilational constitutive relation reflecting the softening behaviour of material, and the failure criterion associated with the constitutive equation, have been studied in detail. Firstly, considerable efforts were made on the numerical integration and computer implementation for the non trivial dilational Gurson Tvergaard model. Considering the weaknesses of the widely used Euler forward integration algorithms, a family of generalized mid point algorithms is proposed for the Gurson Tvergaard model. Correspondingly, based on the decomposition of stresses into hydrostatic and deviatoric parts, an explicit seven parameter expression for the consistent tangent moduli of the algorithms is presented. This explicit formula avoids any matrix inversion during numerical iteration and thus greatly facilitates the computer implementation of the algorithms and increase the efficiency of the code. The accuracy of the proposed algorithms and other conventional algorithms has been assessed in a systematic manner in order to highlight the best algorithm for this study. The accurate and efficient performance of present finite element implementation of the proposed algorithms has been demonstrated by various numerical examples. It has been found that the true mid point algorithm (a = 0.5) is the most accurate one when the deviatoric strain increment is radial to the yield surface and it is very important to use the consistent tangent moduli in the Newton iteration procedure. Secondly, an assessment of the consistency of current local failure criteria for ductile fracture, the critical void growth criterion, the constant critical void volume fraction criterion and Thomason's plastic limit load failure criterion, has been made. Significant differences in the predictions of ductility by the three criteria were found. By assuming the void grows spherically and using the void volume fraction from the Gurson Tvergaard model to calculate the current void matrix geometry, Thomason's failure criterion has been modified and a new failure criterion for the Gurson Tvergaard model is presented. Comparison with Koplik and Needleman's finite element results shows that the new failure criterion is fairly accurate indeed. A novel feature of the new failure criterion is that a mechanism for void coalescence is incorporated into the constitutive model. Hence the material failure is a natural result of the development of macroscopic plastic flow and the microscopic internal necking mechanism. By the new failure criterion, the critical void volume fraction is not a material constant and the initial void volume fraction and/or void nucleation parameters essentially control the material failure. This feature is very desirable and makes the numerical calibration of void nucleation parameters(s) possible and physically sound. Thirdly, a local approach methodology based on the above two major contributions has been built up in ABAQUS via the user material subroutine UMAT and applied to welded T joints. By using the void nucleation parameters calibrated from simple smooth and notched specimens, it was found that the fracture behaviour of the welded T joints can be well predicted using present methodology. This application has shown how the damage parameters of both base material and heat affected zone (HAZ) material can be obtained in a step by step manner and how useful and capable the local approach methodology is in the analysis of fracture behaviour and crack development as well as structural integrity assessment of practical problems where non homogeneous materials are involved. Finally, a procedure for the possible engineering application of the present methodology is suggested and discussed.

Developing co-operation of business units – exploring synergies and a joint business model

The purpose of this study was to develop co-operation between business units of the company operating in graphic industry. The development was done by searching synergy opportunities between these business units. The final aim was to form a business model, which is based on co-operation of these business units.The literature review of this thesis examines synergies and especially the process concerning the search and implementation of synergies. Also the concept of business model and its components are examined. The research was done by using qualitative research method. The main data acquiring method to the empirical part was theme interviews. The data was analyzed using thematisation and content analysis.The results of the study include seven identified possible synergies and a business model, which is based on the co-operation of the business units. The synergy opportunities are evaluated and the implementation order of the synergies is suggested. The presented synergies create the base for the proposed business model.