Measurement Problems and Problem-Solving in Kraft Pulping

Tämän työn tarkoituksena on koota yhteen selluprosessin mittausongelmat ja mahdolliset mittaustekniikat ongelmien ratkaisemiseksi. Pääpaino on online-mittaustekniikoissa. Työ koostuu kolmesta osasta. Ensimmäinen osa on kirjallisuustyö, jossa esitellään nykyaikaisen selluprosessin perusmittaukset ja säätötarpeet. Mukana on koko kuitulinja puunkäsittelystä valkaisuun ja kemikaalikierto: haihduttamo, soodakattila, kaustistamo ja meesauuni. Toisessa osassa mittausongelmat ja mahdolliset mittaustekniikat on koottu yhteen ”tiekartaksi”. Tiedot on koottu vierailemalla kolmella suomalaisella sellutehtaalla ja haastattelemalla laitetekniikka- ja mittaustekniikka-asiantuntijoita. Prosessikemian paremmalle ymmärtämiselle näyttää haastattelun perusteella olevan tarvetta, minkä vuoksi konsentraatiomittaukset on valittu jatkotutkimuskohteeksi. Viimeisessä osassa esitellään mahdollisia mittaustekniikoita konsentraatiomittausten ratkaisemiseksi. Valitut tekniikat ovat lähi-infrapunatekniikka (NIR), fourier-muunnosinfrapunatekniikka (FTIR), online-kapillaarielektroforeesi (CE) ja laserindusoitu plasmaemissiospektroskopia (LIPS). Kaikkia tekniikoita voi käyttää online-kytkettyinä prosessikehitystyökaluina. Kehityskustannukset on arvioitu säätöön kytketylle online-laitteelle. Kehityskustannukset vaihtelevat nollasta miestyövuodesta FTIR-tekniikalle viiteen miestyövuoteen CE-laitteelle; kehityskustannukset riippuvat tekniikan kehitysasteesta ja valmiusasteesta tietyn ongelman ratkaisuun. Työn viimeisessä osassa arvioidaan myös yhden mittausongelman – pesuhäviömittauksen – ratkaisemisen teknis-taloudellista kannattavuutta. Ligniinipitoisuus kuvaisi nykyisiä mittauksia paremmin todellista pesuhäviötä. Nykyään mitataan joko natrium- tai COD-pesuhäviötä. Ligniinipitoisuutta voidaan mitata UV-absorptiotekniikalla. Myös CE-laitetta voitaisiin käyttää pesuhäviön mittauksessa ainakin prosessikehitysvaiheessa. Taloudellinen tarkastelu pohjautuu moniin yksinkertaistuksiin ja se ei sovellu suoraan investointipäätösten tueksi. Parempi mittaus- ja säätöjärjestelmä voisi vakauttaa pesemön ajoa. Investointi ajoa vakauttavaan järjestelmään on kannattavaa, jos todellinen ajotilanne on tarpeeksi kaukana kustannusminimistä tai jos pesurin ajo heilahtelee eli pesuhäviön keskihajonta on suuri. 50 000 € maksavalle mittaus- ja säätöjärjestelmälle saadaan alle 0,5 vuoden takaisinmaksuaika epävakaassa ajossa, jos COD-pesuhäviön vaihteluväli on 5,2 – 11,6 kg/odt asetusarvon ollessa 8,4 kg/odt. Laimennuskerroin vaihtelee tällöin välillä 1,7 – 3,6 m3/odt asetusarvon ollessa 2,5 m3/odt.

Parallella, dynamiska representationer i gymnasiefysiken : implementering av ett interaktivt datorverktyg i didaktiska situationer och uppfattning av effektivt lärande

The computer is a useful tool in the teaching of upper secondary school physics, and should not have a subordinate role in students' learning process. However, computers and computer-based tools are often not available when they could serve their purpose best in the ongoing teaching. Another problem is the fact that commercially available tools are not usable in the way the teacher wants. The aim of this thesis was to try out a novel teaching scenario in a complicated subject in physics, electrodynamics. The didactic engineering of the thesis consisted of developing a computer-based simulation and training material, implementing the tool in physics teaching and investigating its effectiveness in the learning process. The design-based research method, didactic engineering (Artigue, 1994), which is based on the theoryof didactical situations (Brousseau, 1997), was used as a frame of reference for the design of this type of teaching product. In designing the simulation tool a general spreadsheet program was used. The design was based on parallel, dynamic representations of the physics behind the function of an AC series circuit in both graphical and numerical form. The tool, which was furnished with possibilities to control the representations in an interactive way, was hypothesized to activate the students and promote the effectiveness of their learning. An effect variable was constructed in order to measure the students' and teachers' conceptions of learning effectiveness. The empirical study was twofold. Twelve physics students, who attended a course in electrodynamics in an upper secondary school, participated in a class experiment with the computer-based tool implemented in three modes of didactical situations: practice, concept introduction and assessment. The main goal of the didactical situations was to have students solve problems and study the function of AC series circuits, taking responsibility for theirown learning process. In the teacher study eighteen Swedish speaking physics teachers evaluated the didactic potential of the computer-based tool and the accompanying paper-based material without using them in their physics teaching. Quantitative and qualitative data were collected using questionnaires, observations and interviews. The result of the studies showed that both the group of students and the teachers had generally positive conceptions of learning effectiveness. The students' conceptions were more positive in the practice situation than in the concept introduction situation, a setting that was more explorative. However, it turned out that the students' conceptions were also positive in the more complex assessment situation. This had not been hypothesized. A deeper analysis of data from observations and interviews showed that one of the students in each pair was more active than the other, taking more initiative and more responsibilityfor the student-student and student-computer interaction. These active studentshad strong, positive conceptions of learning effectiveness in each of the threedidactical situations. The group of less active students had a weak but positive conception in the first iv two situations, but a negative conception in the assessment situation, thus corroborating the hypothesis ad hoc. The teacher study revealed that computers were seldom used in physics teaching and that computer programs were in short supply. The use of a computer was considered time-consuming. As long as physics teaching with computer-based tools has to take place in special computer rooms, the use of such tools will remain limited. The affordance is enhanced when the physical dimensions as well as the performance of the computer are optimised. As a consequence, the computer then becomes a real learning tool for each pair of students, smoothly integrated into the ongoing teaching in the same space where teaching normally takes place. With more interactive support from the teacher, the computer-based parallel, dynamic representations will be efficient in promoting the learning process of the students with focus on qualitative reasoning - an often neglected part of the learning process of the students in upper secondary school physics.

Movax Oy:n tuotteiden ja tekniikan käyttömahdollisuudet pilaantuneiden maa-alueiden ja pohjavesien kunnostushankkeissa

Työn tavoitteena on tarkastella erilaisia in-situ -kunnostusmenetelmiä maaperän ja pohjaveden kunnostushankkeissa ja niiden toteutusvaihtoehtoja sekä vertailla niitä keskenään. Työssä tarkastellaan myös lainsäädännön ja eri menetelmien kehittymistä, niiden tulevaisuuden näkymiä sekä pohditaan yrityksen tuotteiden liiketoimintamahdollisuuksia tämän pohjalta. Tietoa kerätään kirjallisuudesta sekä tapaustutkimuksista ja niitä peilataan yrityksen sisällä olevaan hiljaiseen tietoon. Löydettyä kirjallisuustietoa sekä tapaustutkimuksia on analysoitu SWOT-analyysien sekä ryhmittelyjen avulla. Työn tuloksena on esitetty vaihtoehtoinen tapa asentaa reaktiivinen seinämä pohjaveden kunnostushankkeissa yrityksen tuotteiden ja putkipaalujen avulla. Lisäksi työn pohjalta voidaan koota materiaalia ja lisätietoa asiakkaille sekä myynnin ja markkinoinnin tukemiseen. Tulosten pohjalta voidaan arvioida, että kyseinen menetelmä tukisi myös kestävän kehityksen periaatteita kunnostushankkeen toteutus- ja asennusvaiheessa. Menetelmän avulla voitaisiin mahdollisesti vähentää reaktiivisten seinämien asentamiseen liittyviä ympäristövaikutuksia.

Introducing Basic Systematic Requirements Engineering Practices in Small Organizations with an Easy to Adopt Method

Requirements-relatedissues have been found the third most important risk factor in software projects and as the biggest reason for software project failures. This is not a surprise since; requirements engineering (RE) practices have been reported deficient inmore than 75% of all; enterprises. A problem analysis on small and low maturitysoftware organizations revealed two; central reasons for not starting process improvement efforts: lack of resources and uncertainty; about process improvementeffort paybacks.; In the constructive part of the study a basic RE method, BaRE, was developed to provide an; easy to adopt way to introduce basic systematic RE practices in small and low maturity; organizations. Based on diffusion of innovations literature, thirteen desirable characteristics; were identified for the solution and the method was implemented in five key components:; requirements document template, requirements development practices, requirements; management practices, tool support for requirements management, and training.; The empirical evaluation of the BaRE method was conducted in three industrial case studies. In; this evaluation, two companies established a completely new RE infrastructure following the; suggested practices while the third company conducted continued requirements document; template development based on the provided template and used it extensively in practice. The; real benefits of the adoption of the method were visible in the companies in four to six months; from the start of the evaluation project, and the two small companies in the project completed; their improvement efforts with an input equal to about one person month. The collected dataon; the case studies indicates that the companies implemented new practices with little adaptations; and little effort. Thus it can be concluded that the constructed BaRE method is indeed easy to; adopt and it can help introduce basic systematic RE practices in small organizations.

Adaptation of TRIZ Method for Problem Solving in Process Engineering

TRIZ is one of the well-known tools, based on analytical methods for creative problem solving. This thesis suggests adapted version of contradiction matrix, a powerful tool of TRIZ and few principles based on concept of original TRIZ. It is believed that the proposed version would aid in problem solving, especially those encountered in chemical process industries with unit operations. In addition, this thesis would help fresh process engineers to recognize importance of various available methods for creative problem solving and learn TRIZ method of creative problem solving. This thesis work mainly provides idea on how to modify TRIZ based method according to ones requirements to fit in particular niche area and solve problems efficiently in creative way. Here in this case, the contradiction matrix developed is based on review of common problems encountered in chemical process industry, particularly in unit operations and resolutions are based on approaches used in past to handle those issues.

Combining Good Practices : Method to study Introductory Physics in Engineering Education

Julkaisumaa: 056 BE BEL Belgia

Optimisation of data analysis method for a fluidized bed combustion test rig

Nowadays the used fuel variety in power boilers is widening and new boiler constructions and running models have to be developed. This research and development is done in small pilot plants where more faster analyse about the boiler mass and heat balance is needed to be able to find and do the right decisions already during the test run. The barrier on determining boiler balance during test runs is the long process of chemical analyses of collected input and outputmatter samples. The present work is concentrating on finding a way to determinethe boiler balance without chemical analyses and optimise the test rig to get the best possible accuracy for heat and mass balance of the boiler. The purpose of this work was to create an automatic boiler balance calculation method for 4 MW CFB/BFB pilot boiler of Kvaerner Pulping Oy located in Messukylä in Tampere. The calculation was created in the data management computer of pilot plants automation system. The calculation is made in Microsoft Excel environment, which gives a good base and functions for handling large databases and calculations without any delicate programming. The automation system in pilot plant was reconstructed und updated by Metso Automation Oy during year 2001 and the new system MetsoDNA has good data management properties, which is necessary for big calculations as boiler balance calculation. Two possible methods for calculating boiler balance during test run were found. Either the fuel flow is determined, which is usedto calculate the boiler's mass balance, or the unburned carbon loss is estimated and the mass balance of the boiler is calculated on the basis of boiler's heat balance. Both of the methods have their own weaknesses, so they were constructed parallel in the calculation and the decision of the used method was left to user. User also needs to define the used fuels and some solid mass flowsthat aren't measured automatically by the automation system. With sensitivity analysis was found that the most essential values for accurate boiler balance determination are flue gas oxygen content, the boiler's measured heat output and lower heating value of the fuel. The theoretical part of this work concentrates in the error management of these measurements and analyses and on measurement accuracy and boiler balance calculation in theory. The empirical part of this work concentrates on the creation of the balance calculation for the boiler in issue and on describing the work environment.

Finding the Fit Between Engineering Design and Cost Information

This paper analyzes the possibilities of integrating cost information and engineering design. Special emphasis is put on finding the potential of using the activity-based costing (ABC) method. Today, the problem of cost estimation in engineering design is that there are two separate extremes of knowledge. On the one extreme, the engineers model the technical parametres behindcosts in great detail but do not get appropriate cost information to their elegant models. On the other extreme, the accounting professionals are stuck with traditional cost accounting methods driven by the procedures and cycles of financial accounting. Therefore, in many cases, the cost information needs of various decision making groups, for example design engineers, are not served satisfactorily. This paper studies if the activity-based costing (ABC) method could offer a compromise between the two extremes. Recognizing activities and activity chains as well as activity and cost drivers could be specially beneficial for design engineers. Also, recognizing the accurate and reliable product costs of existing products helps when doing variant design. However, ABC is not at its best if the cost system becomes too complicated. This is why a comprehensive ABC-cost information system with detailed cost information for the use of design engineers should be examined critically. ABC is at its best when considering such issues as which activities drive costs, the cost of product complexity, allocating indirect costs on the products, the relationships between processes and costs, and the cost of excess capacity.

Communicating Cost Information to Design Engineers using an Activity-based Costing Method

This paper analyzes the possibilities of integrating cost information and engineering design. Special emphasis is on finding the potential of using the activity-based costing (ABC) method when formulating cost information for the needs of design engineers. This paper suggests that ABC is more useful than the traditional job order costing, but the negative issue is the fact that ABC models become easily too complicated, i.e. expensive to build and maintain, and difficult to use. For engineering design the most suitable elements of ABC are recognizing activities of the company, constructing acitivity chains, identifying resources, activity and cost drivers, as wellas calculating accurate product costs. ABC systems including numerous cost drivers can become complex. Therefore, a comprehensive ABC based cost information system for the use of design engineers should be considered criticaly. Combining the suitable ideas of ABC with engineering oriented thinking could give competentresults.

Conflict-based Method for Conceptual Process Synthesis

The changing business environment demands that chemical industrial processes be designed such that they enable the attainment of multi-objective requirements and the enhancement of innovativedesign activities. The requirements and key issues for conceptual process synthesis have changed and are no longer those of conventional process design; there is an increased emphasis on innovative research to develop new concepts, novel techniques and processes. A central issue, how to enhance the creativity of the design process, requires further research into methodologies. The thesis presentsa conflict-based methodology for conceptual process synthesis. The motivation of the work is to support decision-making in design and synthesis and to enhance the creativity of design activities. It deals with the multi-objective requirements and combinatorially complex nature of process synthesis. The work is carriedout based on a new concept and design paradigm adapted from Theory of InventiveProblem Solving methodology (TRIZ). TRIZ is claimed to be a `systematic creativity' framework thanks to its knowledge based and evolutionary-directed nature. The conflict concept, when applied to process synthesis, throws new lights on design problems and activities. The conflict model is proposed as a way of describing design problems and handling design information. The design tasks are represented as groups of conflicts and conflict table is built as the design tool. The general design paradigm is formulated to handle conflicts in both the early and detailed design stages. The methodology developed reflects the conflict nature of process design and synthesis. The method is implemented and verified through case studies of distillation system design, reactor/separator network design and waste minimization. Handling the various levels of conflicts evolve possible design alternatives in a systematic procedure which consists of establishing an efficient and compact solution space for the detailed design stage. The approach also provides the information to bridge the gap between the application of qualitative knowledge in the early stage and quantitative techniques in the detailed design stage. Enhancement of creativity is realized through the better understanding of the design problems gained from the conflict concept and in the improvement in engineering design practice via the systematic nature of the approach.

Particle transport method for convection-diffusion-reaction problems

Convective transport, both pure and combined with diffusion and reaction, can be observed in a wide range of physical and industrial applications, such as heat and mass transfer, crystal growth or biomechanics. The numerical approximation of this class of problemscan present substantial difficulties clue to regions of high gradients (steep fronts) of the solution, where generation of spurious oscillations or smearing should be precluded. This work is devoted to the development of an efficient numerical technique to deal with pure linear convection and convection-dominated problems in the frame-work of convection-diffusion-reaction systems. The particle transport method, developed in this study, is based on using rneshless numerical particles which carry out the solution along the characteristics defining the convective transport. The resolution of steep fronts of the solution is controlled by a special spacial adaptivity procedure. The serni-Lagrangian particle transport method uses an Eulerian fixed grid to represent the solution. In the case of convection-diffusion-reaction problems, the method is combined with diffusion and reaction solvers within an operator splitting approach. To transfer the solution from the particle set onto the grid, a fast monotone projection technique is designed. Our numerical results confirm that the method has a spacial accuracy of the second order and can be faster than typical grid-based methods of the same order; for pure linear convection problems the method demonstrates optimal linear complexity. The method works on structured and unstructured meshes, demonstrating a high-resolution property in the regions of steep fronts of the solution. Moreover, the particle transport method can be successfully used for the numerical simulation of the real-life problems in, for example, chemical engineering.

Cost information in engineering design -Potentials and limitations of activity-based costing

The purpose of this thesis is to analyse activity-based costing (ABC) and possible modified versions ofit in engineering design context. The design engineers need cost information attheir decision-making level and the cost information should also have a strong future orientation. These demands are high because traditional management accounting has concentrated on the direct actual costs of the products. However, cost accounting has progressed as ABC was introduced late 1980s and adopted widely bycompanies in the 1990s. The ABC has been a success, but it has gained also criticism. In some cases the ambitious ABC systems have become too complex to build,use and update. This study can be called an action-oriented case study with some normative features. In this thesis theoretical concepts are assessed and allowed to unfold gradually through interaction with data from three cases. The theoretical starting points are ABC and theory of engineering design process (chapter2). Concepts and research results from these theoretical approaches are summarized in two hypotheses (chapter 2.3). The hypotheses are analysed with two cases (chapter 3). After the two case analyses, the ABC part is extended to cover alsoother modern cost accounting methods, e.g. process costing and feature costing (chapter 4.1). The ideas from this second theoretical part are operationalized with the third case (chapter 4.2). The knowledge from the theory and three cases is summarized in the created framework (chapter 4.3). With the created frameworkit is possible to analyse ABC and its modifications in the engineering design context. The framework collects the factors that guide the choice of the costing method to be used in engineering design. It also illuminates the contents of various ABC-related costing methods. However, the framework needs to be further tested. On the basis of the three cases it can be said that ABC should be used cautiously when formulating cost information for engineering design. It is suitable when the manufacturing can be considered simple, or when the design engineers are not cost conscious, and in the beginning of the design process when doing adaptive or variant design. If the design engineers need cost information for the embodiment or detailed design, or if manufacturing can be considered complex, or when design engineers are cost conscious, the ABC has to be always evaluated critically.

Measuring organizational capabilities in the engineering and consulting industry

Tämän työn tarkoituksena oli tutkia kuinka organisaation kyvykkyyksiä voidaan mitata engineering- ja konsultointialalla käyttämällä ns. kyvykkyysauditointimenetelmää. Päämotiivit aineettoman omaisuuden mittaamiseksi tunnistettiin kirjallisuuskatsauksen pohjalta. Erilaisten menetelmien etuja ja haittoja tutkittiin, jotta kyvykkyysauditoinnin suorittamiseen liittyvät haasteet ja vaatimukset tulisivat tunnistetuiksi. Kyvykkyysauditoinnin rakentaminen vaati teollisuudenalan erityispiirteiden tunnistamista. Niiksi havaittiin tietointensiivisyys ja projektikeskeisyys. Auditoinnin implementaatioprosessi koostui neljästä osasta, joista kolmen ensimmäisen suorittamiseen case-yritys antoi merkittävän panoksensa. Kriittisten menestystekijöiden selvittämisen jälkeen voitiin niihin vaikuttavat organisaation kyvykkyydet tunnistaa ja arviointi suorittaa. Arvioinnit kerättiin sisäisiltä ja ulkoisilta arvioijilta, ja ne muodostivat pohjan analyysille, joka selvitti yrityksen kehittämistarpeita. Kyvykkyysauditoinnin hyödyiksi laskettiin kasvanut tietämys yrityksen vahvuuksista ja heikkouksista sekä mahdollisuus tarkkailla säännöllisesti sen kokonaissuorituskykyä ja parantaa sitä.