On the Application of Beam on Elastic Foundation Theory to the Analysis of Stiffened Plate Strips

The main objective of this thesis is to show that plate strips subjected to transverse line loads can be analysed by using the beam on elastic foundation (BEF) approach. It is shown that the elastic behaviour of both the centre line section of a semi infinite plate supported along two edges, and the free edge of a cantilever plate strip can be accurately predicted by calculations based on the two parameter BEF theory. The transverse bending stiffness of the plate strip forms the foundation. The foundation modulus is shown, mathematically and physically, to be the zero order term of the fourth order differential equation governing the behaviour of BEF, whereas the torsion rigidity of the plate acts like pre tension in the second order term. Direct equivalence is obtained for harmonic line loading by comparing the differential equations of Levy's method (a simply supported plate) with the BEF method. By equating the second and zero order terms of the semi infinite BEF model for each harmonic component, two parameters are obtained for a simply supported plate of width B: the characteristic length, 1/ λ, and the normalized sum, n, being the effect of axial loading and stiffening resulting from the torsion stiffness, nlin. This procedure gives the following result for the first mode when a uniaxial stress field was assumed (ν = 0): 1/λ = √2B/π and nlin = 1. For constant line loading, which is the superimposition of harmonic components, slightly differing foundation parameters are obtained when the maximum deflection and bending moment values of the theoretical plate, with v = 0, and BEF analysis solutions are equated: 1 /λ= 1.47B/π and nlin. = 0.59 for a simply supported plate; and 1/λ = 0.99B/π and nlin = 0.25 for a fixed plate. The BEF parameters of the plate strip with a free edge are determined based solely on finite element analysis (FEA) results: 1/λ = 1.29B/π and nlin. = 0.65, where B is the double width of the cantilever plate strip. The stress biaxial, v > 0, is shown not to affect the values of the BEF parameters significantly the result of the geometric nonlinearity caused by in plane, axial and biaxial loading is studied theoretically by comparing the differential equations of Levy's method with the BEF approach. The BEF model is generalised to take into account the elastic rotation stiffness of the longitudinal edges. Finally, formulae are presented that take into account the effect of Poisson's ratio, and geometric non linearity, on bending behaviour resulting from axial and transverse inplane loading. It is also shown that the BEF parameters of the semi infinite model are valid for linear elastic analysis of a plate strip of finite length. The BEF model was verified by applying it to the analysis of bending stresses caused by misalignments in a laboratory test panel. In summary, it can be concluded that the advantages of the BEF theory are that it is a simple tool, and that it is accurate enough for specific stress analysis of semi infinite and finite plate bending problems.

Effect of Mechanical and Geometric Mismatching on Fatigue and Damage of Welded Joints

The future of high technology welded constructions will be characterised by higher strength materials and improved weld quality with respect to fatigue resistance. The expected implementation of high quality high strength steel welds will require that more attention be given to the issues of crack initiation and mechanical mismatching. Experiments and finite element analyses were performed within the framework of continuum damage mechanics to investigate the effect of mismatching of welded joints on void nucleation and coalescence during monotonic loading. It was found that the damage of undermatched joints mainly occurred in the sandwich layer and the damageresistance of the joints decreases with the decrease of the sandwich layer width. The damage of over-matched joints mainly occurred in the base metal adjacent to the sandwich layer and the damage resistance of the joints increases with thedecrease of the sandwich layer width. The mechanisms of the initiation of the micro voids/cracks were found to be cracking of the inclusions or the embrittled second phase, and the debonding of the inclusions from the matrix. Experimental fatigue crack growth rate testing showed that the fatigue life of under-matched central crack panel specimens is longer than that of over-matched and even-matched specimens. Further investigation by the elastic-plastic finite element analysis indicated that fatigue crack closure, which originated from the inhomogeneousyielding adjacent to the crack tip, played an important role in the fatigue crack propagation. The applicability of the J integral concept to the mismatched specimens with crack extension under cyclic loading was assessed. The concept of fatigue class used by the International Institute of Welding was introduced in the parametric numerical analysis of several welded joints. The effect of weld geometry and load condition on fatigue strength of ferrite-pearlite steel joints was systematically evaluated based on linear elastic fracture mechanics. Joint types included lap joints, angle joints and butt joints. Various combinations of the tensile and bending loads were considered during the evaluation with the emphasis focused on the existence of both root and toe cracks. For a lap joint with asmall lack-of-penetration, a reasonably large weld leg and smaller flank angle were recommended for engineering practice in order to achieve higher fatigue strength. It was found that the fatigue strength of the angle joint depended strongly on the location and orientation of the preexisting crack-like welding defects, even if the joint was welded with full penetration. It is commonly believed that the double sided butt welds can have significantly higher fatigue strength than that of a single sided welds, but fatigue crack initiation and propagation can originate from the weld root if the welding procedure results in a partial penetration. It is clearly shown that the fatigue strength of the butt joint could be improved remarkably by ensuring full penetration. Nevertheless, increasing the fatigue strength of a butt joint by increasing the size of the weld is an uneconomical alternative.

Statistical variation of weld profiles and their expected influence on fatigue strength

The general objective of this study was to conduct astatistical analysis on the variation of the weld profiles and their influence on the fatigue strength of the joint. Weld quality with respect to its fatigue strength is of importance which is the main concept behind this thesis. The intention of this study was to establish the influence of weld geometric parameters on the weld quality and fatigue strength. The effect of local geometrical variations of non-load carrying cruciform fillet welded joint under tensile loading wasstudied in this thesis work. Linear Elastic Fracture Mechanics was used to calculate fatigue strength of the cruciform fillet welded joints in as-welded condition and under cyclic tensile loading, for a range of weld geometries. With extreme value statistical analysis and LEFM, an attempt was made to relate the variation of the cruciform weld profiles such as weld angle and weld toe radius to respective FAT classes.

Kosketukseton hitsin pintageometrian määrittäminen

Yleisesti tiedetään hitsin pintageometrian vaikuttavan rakenteen väsymislujuuteen. Nopean, edullisen ja luotettavan pintageometrian mittausmenetelmän kehittäminen on askel kohti tarkempaa ja varmempaa rakenteen väsymislujuuden tarkastelua. Tässä työssä on tutkittu hitsejä, joiden pinnan geometria on mitattu norjalaisen SINTEF -yrityksen kehittämällä rakenteellisen valon menetelmällä. Osana työtä kehitettiin MatLab -pohjainen ohjelma, jolla jälkikäsitellään mittauksesta saadut x-y-z -mittapisteet. Mittausdatan jälkikäsittelyssä saadaan mittauksesta määritettyähitsin reunan pyöristys, liittymäkulma, a-mitta, reunahaava ja kateettisuhde. Kehitettyä menetelmää käyttämällä mitattiin lähes 300 voimaakantamatontaristiliitoksen hitsiä. Mittaustuloksia verrattiin vastaavista kappaleista tehtyihin hiemittauksiin. Manuaalisen hieestä tehdyn mittauksen havaittiin olevan tarkempi ja pystyttiin havaitsemaan paikallisempia muotoja. Rakenteellisen valon mittauksissa tapahtunut heijastelu saatiin pienenemään käsittelemällä mitattava pinta mattavalkoisella maalilla. Rakenteellisen valon mittatarkkuudeksi saatiin noin 0,2 mm. Pohjautuen mitattuun hitsin reunan pyöristykseen ja liittymäkulmaan voidaan yksinkertaista kaavaa käyttämällä laskea hitsin jännityskonsentraatio ja näin saada alkuarvaus väsymislujuudelle. Myös muiden tekijöiden tiedetään vaikuttavan hitsin väsymislujuuteen, joten pyöristyksen ja liittymäkulman avulla tehdyt arviot eivät ole absoluuttisen oikeita. Tämä havaittiin väsytyskokeilla, joista yhdessä väsymisvaurio ei syntynyt suurimmankaan jännityskonsentraation alueella.

A modified structural stress method for fatigue assessment of welded structures

Fatigue life assessment of weldedstructures is commonly based on the nominal stress method, but more flexible and accurate methods have been introduced. In general, the assessment accuracy is improved as more localized information about the weld is incorporated. The structural hot spot stress method includes the influence of macro geometric effects and structural discontinuities on the design stress but excludes the local features of the weld. In this thesis, the limitations of the structural hot spot stress method are discussed and a modified structural stress method with improved accuracy is developed and verified for selected welded details. The fatigue life of structures in the as-welded state consists mainly of crack growth from pre-existing cracks or defects. Crack growth rate depends on crack geometry and the stress state on the crack face plane. This means that the stress level and shape of the stress distribution in the assumed crack path governs thetotal fatigue life. In many structural details the stress distribution is similar and adequate fatigue life estimates can be obtained just by adjusting the stress level based on a single stress value, i.e., the structural hot spot stress. There are, however, cases for which the structural stress approach is less appropriate because the stress distribution differs significantly from the more common cases. Plate edge attachments and plates on elastic foundations are some examples of structures with this type of stress distribution. The importance of fillet weld size and weld load variation on the stress distribution is another central topic in this thesis. Structural hot spot stress determination is generally based on a procedure that involves extrapolation of plate surface stresses. Other possibilities for determining the structural hot spot stress is to extrapolate stresses through the thickness at the weld toe or to use Dong's method which includes through-thickness extrapolation at some distance from the weld toe. Both of these latter methods are less sensitive to the FE mesh used. Structural stress based on surface extrapolation is sensitive to the extrapolation points selected and to the FE mesh used near these points. Rules for proper meshing, however, are well defined and not difficult to apply. To improve the accuracy of the traditional structural hot spot stress, a multi-linear stress distribution is introduced. The magnitude of the weld toe stress after linearization is dependent on the weld size, weld load and plate thickness. Simple equations have been derived by comparing assessment results based on the local linear stress distribution and LEFM based calculations. The proposed method is called the modified structural stress method (MSHS) since the structural hot spot stress (SHS) value is corrected using information on weld size andweld load. The correction procedure is verified using fatigue test results found in the literature. Also, a test case was conducted comparing the proposed method with other local fatigue assessment methods.

Analytical Study on the Influence of Geometrical Parameters on the Fatigue Strength of Welds with Undercuts

The purpose of this study is to analyze the influence of geometric parameters on the fatigue strength of the welded joint. The thesis includes the analytical study pertaining to variation of undercut and the weld toe radius. The theoretical part includes the concepts of fracture mechanics, different stages of the crack propagation and finally the results. The numerical results are obtained from FRANC2D/L. The results show that the fatigue strength of the welded structure depends on the parameters of the welds such as the weld toe radius, weld angle, height of the undercut and plate thickness. The results show that the fatigue life can be improved by having the undercut as minimum as possible. However there has been significant variation on the fatigue life of the structure when the weld toe radius is increased.

Environmental Monitoring using Image Analysis

Tärkeä tehtävä ympäristön tarkkailussa on arvioida ympäristön nykyinen tila ja ihmisen siihen aiheuttamat muutokset sekä analysoida ja etsiä näiden yhtenäiset suhteet. Ympäristön muuttumista voidaan hallita keräämällä ja analysoimalla tietoa. Tässä diplomityössä on tutkittu vesikasvillisuudessa hai vainuja muutoksia käyttäen etäältä hankittua mittausdataa ja kuvan analysointimenetelmiä. Ympäristön tarkkailuun on käytetty Suomen suurimmasta järvestä Saimaasta vuosina 1996 ja 1999 otettuja ilmakuvia. Ensimmäinen kuva-analyysin vaihe on geometrinen korjaus, jonka tarkoituksena on kohdistaa ja suhteuttaa otetut kuvat samaan koordinaattijärjestelmään. Toinen vaihe on kohdistaa vastaavat paikalliset alueet ja tunnistaa kasvillisuuden muuttuminen. Kasvillisuuden tunnistamiseen on käytetty erilaisia lähestymistapoja sisältäen valvottuja ja valvomattomia tunnistustapoja. Tutkimuksessa käytettiin aitoa, kohinoista mittausdataa, minkä perusteella tehdyt kokeet antoivat hyviä tuloksia tutkimuksen onnistumisesta.

Spectral Analysis of Buffers in Communication Systems

Muokatun matriisi-geometrian tekniikan kehitys yleimmäksi jonoksi on esitelty tässä työssä. Jonotus systeemi koostuu useista jonoista joilla on rajatut kapasiteetit. Tässä työssä on myös tutkittu PH-tyypin jakautumista kun ne jaetaan. Rakenne joka vastaa lopullista Markovin ketjua jossa on itsenäisiä matriiseja joilla on QBD rakenne. Myös eräitä rajallisia olotiloja on käsitelty tässä työssä. Sen esitteleminen matriisi-geometrisessä muodossa, muokkaamalla matriisi-geometristä ratkaisua on tämän opinnäytetyön tulos.

Matrix Analytic Analysis of Delays in Communication Systems

Tässä päättötyössä annetaan kuvaus kehitetystä sovelluksesta Quasi Birth Death processien ratkaisuun. Tämä ohjelma on tähän mennessä ainutlaatuinen ja sen avulla voi ratkaista sarjan tehtäviä ja sitä tarvitaan kommunikaatio systeemien analyysiin. Mainittuun sovellukseen on annettu kuvaus ja määritelmä. Lyhyt kuvaus toisesta sovelluksesta Quasi Birth Death prosessien tehtävien ratkaisuun on myös annettu

Multispectral Analysis of Paper Production Phases

Paperitehtaissa paperin väriä arvioidaan L*a*b –arvojen perusteella. Tämä lähestymistapa ei ole tarkka ja johtaa siihen, että saman luokkaan kuuluvat paperit saatetaan havaita eri värisinä. Tässä diplomityössä tarkastellaan värien arviointia multispektraalisen kuvantamisen avulla. Menetelmän ajatuksena on verrata standardoidun heijastuman spektriä kohteena olevan paperirullan heijastuman spektriin mittaustapojen avulla. 12:n kirjallisuuteen perustuvan ja yhden tutkimusryhmämme kehittämän mittaustavan joukosta pyrittiin valitsemaan parhaat mittaustavat tutkimuksien perusteella. Mittaustavan tehokkuus tarkoittaa kykä tunnistaa eroavaisuuksia värisävyn, värikylläisyyden ja valoisuuden perusteella. Mittaustapoja tutkittiin sekä keinotekoisilla kuvilla että aidoilla paperinäytteillä. Tuloksena maksimi-minimi-, aritmeettisen keskiarvon minimi- ja geometrisen keskiarvon minimimenetelmä olivat parhaita mittaustapoja.

Computing the diameter of Coxeter groups

This thesis addresses the problem of computing the minimal and maximal diameter of the Cayley graph of Coxeter groups. We first present and assert relevant parts of polytope theory and related Coxeter theory. After this, a method of contracting the orthogonal projections of a polytope from Rd onto R2 and R3, d ¸ 3 is presented. This method is the Equality Set Projection algorithm that requires a constant number of linearprogramming problems per facet of the projection in the absence of degeneracy. The ESP algorithm allows us to compute also projected geometric diameters of high-dimensional polytopes. A representation set of projected polytopes is presented to illustrate the methods adopted in this thesis.

Size Effect and Notch Size Effect in Metal Fatigue

It is a well known phenomenon that the constant amplitude fatigue limit of a large component is lower than the fatigue limit of a small specimen made of the same material. In notched components the opposite occurs: the fatigue limit defined as the maximum stress at the notch is higher than that achieved with smooth specimens. These two effects have been taken into account in most design handbooks with the help of experimental formulas or design curves. The basic idea of this study is that the size effect can mainly be explained by the statistical size effect. A component subjected to an alternating load can be assumed to form a sample of initiated cracks at the end of the crack initiation phase. The size of the sample depends on the size of the specimen in question. The main objective of this study is to develop a statistical model for the estimation of this kind of size effect. It was shown that the size of a sample of initiated cracks shall be based on the stressed surface area of the specimen. In case of varying stress distribution, an effective stress area must be calculated. It is based on the decreasing probability of equally sized initiated cracks at lower stress level. If the distribution function of the parent population of cracks is known, the distribution of the maximum crack size in a sample can be defined. This makes it possible to calculate an estimate of the largest expected crack in any sample size. The estimate of the fatigue limit can now be calculated with the help of the linear elastic fracture mechanics. In notched components another source of size effect has to be taken into account. If we think about two specimens which have similar shape, but the size is different, it can be seen that the stress gradient in the smaller specimen is steeper. If there is an initiated crack in both of them, the stress intensity factor at the crack in the larger specimen is higher. The second goal of this thesis is to create a calculation method for this factor which is called the geometric size effect. The proposed method for the calculation of the geometric size effect is also based on the use of the linear elastic fracture mechanics. It is possible to calculate an accurate value of the stress intensity factor in a non linear stress field using weight functions. The calculated stress intensity factor values at the initiated crack can be compared to the corresponding stress intensity factor due to constant stress. The notch size effect is calculated as the ratio of these stress intensity factors. The presented methods were tested against experimental results taken from three German doctoral works. Two candidates for the parent population of initiated cracks were found: the Weibull distribution and the log normal distribution. Both of them can be used successfully for the prediction of the statistical size effect for smooth specimens. In case of notched components the geometric size effect due to the stress gradient shall be combined with the statistical size effect. The proposed method gives good results as long as the notch in question is blunt enough. For very sharp notches, stress concentration factor about 5 or higher, the method does not give sufficient results. It was shown that the plastic portion of the strain becomes quite high at the root of this kind of notches. The use of the linear elastic fracture mechanics becomes therefore questionable.

Jäykistetyn laattarakenteen mitoittaminen suurten taipumien teorialla

Tässä diplomityössä tutkitaan epälineaarisen teorian hyödyntämistä laattarakenteiden analysoinnissa ja pyritään muodostamaan yksinkertaisia mitoitusohjeita laattarakenteille. Analysointia varten laattarakenne jaetaan lohkoihin, joille mitoitussäännöt määritetään. Tarkastellaan myös lineaarisen ja epälineaarisen teorian antamien tulosten eroavai-suutta ja suurten taipumien huomioimisen aiheuttamaa hyötyä. Työn lähtökohtana on standardi SFS-EN 1993-1-7, joka antaa yksinkertaistettuja mitoitusohjeita laattarakenteiden mitoitukseen lineaarisella ja epälineaarisella teorialla. Työssä selvitetään mistä nämä mitoitusohjeet ovat peräisin. Lisäksi tarkastellaan laattalohkojen erilaisia liitoksia, jotta voidaan tehdä oletuksia laatan reunaehdoista. Tulokseksi saadaan suuntaa-antavia mitoitusohjeita, joiden soveltaminen onnistuu vain muutamille yksinkertaisille rakenteille. Mitoitusohjeiden perusteella saadaan laskettua laattalohkon jännitykset, taipuma sekä mitoitusohjeiden vaatiman jäykisteen koko. Jotta mitoitusohjeista saataisiin tarkemmat, tulisi mitoitettava rakenne pystyä määrittelemään yksityiskohtaisemmin. Vertailtaessa lineaarista ja epälineaarista laskentaa havaitaan, että huomioimalla suurten taipumien aikaansaamat kalvovoimat, laskevat laattarakenteeseen vaikuttavat taipumat ja jännitykset merkittävästikin.

Ultrakevyen rahtialuksen kansiluukkujen sekä luukkujen siirto- ja varastointijärjestelmän suunnittelu hyödyntäen kevytrakennekonsepteja

Tämän työn tarkoituksena oli tutkia miten rahtialuksen kansiluukut voitaisiin valmistaa mahdollisimman kevyiksi. Katettavan ruuman pinta-ala on n. 10 m x 40 m. Luukkujen suuresta jännevälistä johtuen, rakenteelta vaaditaan suurta jäykkyyttä. Erilaisina vaihtoehtoina tutkittiin vaahtomaista alumiinia, alumiinisia kennorakenteita ja polyuretaanisia sandwich-rakenteita. Työssä vertailtiin myös erilaisia geometrisia ratkaisuja, joilla kansiluukkujen jäykkyyttä pyrittiin lisäämään ja sitä kautta pääsemään pienempään materiaalin tarpeeseen. Geometriaa suunniteltaessa huomioitiin myös vaikutukset ruuman tilavuuteen ja lainsäädännön asettamat reunaehdot. Lainsäädännöstä saatiin esimerkiksi turvakaiteiden minimikorkeus, joka vaikuttaa suoraan ruuman tilavuuteen, kun aluksen korkeimmaksi kohdaksi on valittu laivan keskilinja ja tämä korkeus on annettu suunnittelun lähtötietona. Tietokoneavusteisen lujuuslaskennan avulla eri vaihtoehdoista muodostettiin elementtimallit. Malleja varioimalla ja tuloksia vertailemalla saatiin selville kevyin mahdollinen rakenne ja geometria. Malleista saatiin selville myös luukkujen tukireaktiovoimat, eli voimat, jotka luukut kohdistavat aluksen muihin rakenteisiin. Lisäksi työssä mietittiin erilaisia tapoja ruuman avaamiseen ja avaamistavan vaikutusta kansiluukkujen painoon, geometriaan ja ruuman tilavuuteen.