Fractional slot permanent magnet synchronous motors for low speed applications

This study compares different rotor structures of permanent magnet motors with fractional slot windings. The surface mounted magnet and the embedded magnet rotor structures are studied. This thesis analyses the characteristics of a concentrated two-layer winding, each coil of which is wound around one tooth and which has a number of slots per pole and per phase less than one (q < 1). Compared to the integer slot winding, the fractional winding (q < 1) has shorter end windings and this, thereby, makes space as well as manufacturing cost saving possible. Several possible ways of winding a fractional slot machine with slots per pole and per phase lessthan one are examined. The winding factor and the winding harmonic components are calculated. The benefits attainable from a machine with concentrated windingsare considered. Rotor structures with surface magnets, radially embedded magnets and embedded magnets in V-position are discussed. The finite element method isused to solve the main values of the motors. The waveform of the induced electro motive force, the no-load and rated load torque ripple as well as the dynamic behavior of the current driven and voltage driven motor are solved. The results obtained from different finite element analyses are given. A simple analytic method to calculate fractional slot machines is introduced and the values are compared to the values obtained with the finite element analysis. Several different fractional slot machines are first designed by using the simple analytical methodand then computed by using the finite element method. All the motors are of thesame 225-frame size, and have an approximately same amount of magnet material, a same rated torque demand and a 400 - 420 rpm speed. An analysis of the computation results gives new information on the character of fractional slot machines.A fractional slot prototype machine with number 0.4 for the slots per pole and per phase, 45 kW output power and 420 rpm speed is constructed to verify the calculations. The measurement and the finite element method results are found to beequal.

Characterization Method for Comminution Behavior of Limestone and Fuel Ash in a Circulating Fluidized Bed Boiler

Työn tavoite oli kehittää karakterisointimenetelmät kalkkikiven ja polttoaineen tuhkan jauhautumisen ennustamiselle kiertoleijukattilan tulipesässä. Kiintoainekäyttäytymisen karakterisoinnilla ja mallintamisella voidaan tarkentaa tulipesän lämmönsiirron ja tuhkajaon ennustamista. Osittain kokeelliset karakterisointimenetelmät perustuvat kalkkikiven jauhautumiseen laboratoriokokoluokan leijutetussa kvartsiputkireaktorissa ja tuhkan jauhatumiseen rotaatiomyllyssä. Karakterisointimenetelmät ottavat huomioon eri-laiset toimintaolosuhteet kaupallisen kokoluokan kiertoleijukattiloissa. Menetelmät kelpoistettiin kaupallisen kokoluokan kiertoleijukattiloista mitattujen ja fraktioittaisella kiintoainemallilla mallinnettujen taseiden avulla. Kelpoistamistaseiden vähäisyydestä huolimatta karakterisointimenetelmät arvioitiin virhetarkastelujen perusteella järkeviksi. Karakterisointimenetelmien kehittämistä ja tarkentamista tullaan jatkamaan.

Defending behavior in bullying situations

In order to encourage children and adolescents to defend and support their victimized peers, it is important to identify factors that either maximize or minimize the probability that students will engage in such behaviors. This thesis is composed of four studies designed to elucidate how a variety of factors work in conjunction to explain why some children defend their victimized classmates, whereas others remain passive or reinforce the bully. The conceptual framework of this thesis is drawn from several theoretical considerations, including social cognitive learning theory, the expectancy-value framework as well as the literature emphasizing the importance of empathy in motivating behaviors. Also the child-by-environment perspective and the socialecological perspective influenced this research. Accordingly, several intra- and interpersonal characteristics (e.g., social cognitions, empathy, and social status) as well as group-level factors (e.g., norms) that may either enhance or reduce the probability that students defend their victimized peers are investigated. In Studies I and II, the focus is on social cognitions, and special attention is paid to take into account the domain-specificity of cognition-behavior processes. Self-efficacy for defending is still an interest of study III, but the role of affective empathy on defending is also investigated. Also social status variables (preference and perceived popularity) are evaluated as possible moderators of links between intrapersonal factors and defending. In Study IV, the focus is expanded further by concentrating on characteristics of children’s proximal environments (i.e., classroom). Bullying norms and collective perceptions (i.e., connectedness among the students and the teachers’ ability to deal with bullying situations) are examined. Data are drawn from two research projects: the Kaarina Cohort Study (consisting of fourth and eighth graders) and the randomized controlled trial (RCT) evaluating the effects of the KiVa antibullying program (consisting of third to fifth graders). The results of the thesis suggest that defending the victims of bullying is influenced by a variety of individual level motivational characteristics, such as social cognitions and affective empathy. Also, both perceived popularity and social preference play a role in defending, and the findings support the conceptualization that behavior results from the interplay between the characteristics of an individual child and their social-relational environment. Classroom context further influences students’ defending behavior. Thus, antibullying efforts targeting peer bystanders should aim to influence intra- and interpersonal characteristics of children and adolescents as well as their social environment.

Cultural distance and negotiation behavior : Perception of entrepreneurs operating in Turku

This thesis investigates the influence of cultural distance on entrepreneurs’ negotiation behaviour. For this purpose, Turku was chosen as the unit of analysis due to the exponential demographic change experienced during the last two decades that has derived in a more diversified local environment. The research aim set for this study was to identify to what extent entrepreneurs face cultural distance, how cultural distance influences the entrepreneur’s negotiation behaviour and how can it be addressed in order to turn dissimilarities into opportunities. This study presented the relation and apparent dichotomy of cultural distance and global culture, including the component of diversity. The impact of cultural distance in the entrepreneurial mindset and its consequent effect in negotiation behaviour was presented too. Addressing questions about the way individuals perceive, behave and interact allowed the use of interviews for this qualitative research study. In the empirical part of this study it was found that negotiation behaviour differed in terms of how congenial entrepreneurs felt when managing cultural distance, encompassing their performance. It was also acknowledged that after time and effort, some of the personal traits were enhanced while others reduced, allowing for more flexibility and adaptation. Furthermore, depending on the level of trust and shared interests, entrepreneurs determined their attitudinal approach, being adaptive or reactive subject to situational aspects. Additionally, it was found that the acquisition of cultural savvy not necessarily conveyed to more creativity. This experiential learning capability led to the proposition of new ways of behaviour. Likewise, it was proposed that growing cultural intelligence bridge distances, reducing mistrusts and misunderstandings. The capability of building more collaborative relationships allows entrepreneurs to see cultural distance as a cultural perspective instead of as a threat. Therefore it was recommended to focus on proximity rather than distance to better identify and exploit untapped opportunities and better perform when negotiating in whichever cultural conditions.

Influence of surface functionalization on the behavior of silica nanoparticles in biological systems

Personalized nanomedicine has been shown to provide advantages over traditional clinical imaging, diagnosis, and conventional medical treatment. Using nanoparticles can enhance and clarify the clinical targeting and imaging, and lead them exactly to the place in the body that is the goal of treatment. At the same time, one can reduce the side effects that usually occur in the parts of the body that are not targets for treatment. Nanoparticles are of a size that can penetrate into cells. Their surface functionalization offers a way to increase their sensitivity when detecting target molecules. In addition, it increases the potential for flexibility in particle design, their therapeutic function, and variation possibilities in diagnostics. Mesoporous nanoparticles of amorphous silica have attractive physical and chemical characteristics such as particle morphology, controllable pore size, and high surface area and pore volume. Additionally, the surface functionalization of silica nanoparticles is relatively straightforward, which enables optimization of the interaction between the particles and the biological system. The main goal of this study was to prepare traceable and targetable silica nanoparticles for medical applications with a special focus on particle dispersion stability, biocompatibility, and targeting capabilities. Nanoparticle properties are highly particle-size dependent and a good dispersion stability is a prerequisite for active therapeutic and diagnostic agents. In the study it was shown that traceable streptavidin-conjugated silica nanoparticles which exhibit a good dispersibility could be obtained by the suitable choice of a proper surface functionalization route. Theranostic nanoparticles should exhibit sufficient hydrolytic stability to effectively carry the medicine to the target cells after which they should disintegrate and dissolve. Furthermore, the surface groups should stay at the particle surface until the particle has been internalized by the cell in order to optimize cell specificity. Model particles with fluorescently-labeled regions were tested in vitro using light microscopy and image processing technology, which allowed a detailed study of the disintegration and dissolution process. The study showed that nanoparticles degrade more slowly outside, as compared to inside the cell. The main advantage of theranostic agents is their successful targeting in vitro and in vivo. Non-porous nanoparticles using monoclonal antibodies as guiding ligands were tested in vitro in order to follow their targeting ability and internalization. In addition to the targeting that was found successful, a specific internalization route for the particles could be detected. In the last part of the study, the objective was to clarify the feasibility of traceable mesoporous silica nanoparticles, loaded with a hydrophobic cancer drug, being applied for targeted drug delivery in vitro and in vivo. Particles were provided with a small molecular targeting ligand. In the study a significantly higher therapeutic effect could be achieved with nanoparticles compared to free drug. The nanoparticles were biocompatible and stayed in the tumor for a longer time than a free medicine did, before being eliminated by renal excretion. Overall, the results showed that mesoporous silica nanoparticles are biocompatible, biodegradable drug carriers and that cell specificity can be achieved both in vitro and in vivo.

Understanding Online Game Players' Post-adoption Behavior: an Investigation of Social Network Games in China

Retaining players and re-attracting switching players has long been a central topic for SNG providers with regard to the post-adoption stage of playing an online game. However, there has not been much research which has explored players’ post-adoption behavior by incorporating the continuance intention and the switching intention. In addition, traditional IS continuance theories were mainly developed to investigate users’ continued use of utilitarian IS, and thus they may fall short when trying to explain the continued use of hedonic IS. Furthermore, compared to the richer literature on IS continuance, far too little attention has been paid to IS switching, leading to a dearth of knowledge on the subject, despite the increased incidence of the switching phenomenon in the IS field. By addressing the limitations of prior literature, this study seeks to examine the determinants of SNG players’ two different post-adoption behaviors, including the continuance intention and the switching intention. This study takes a positivist approach and uses survey research method to test five proposed research models based on Unified Theory of Acceptance and Use of Technology 2; Use and Gratification Theory; Push-Pull-Mooring model; Cognitive Dissonance Theory; and a self-developed model respectively with empirical data collected from the SNG players of one of the biggest SNG providers in China. A total of 3919 valid responses and 541 valid responses were used to examine the continuance intention and the switching intention, respectively. SEM is utilized as the data analysis method. The proposed research models are supported by the empirical data. The continuance intention is determined by enjoyment, fantasy, escapism, social interaction, social presence, social influence, achievement and habit. The switching intention is determined by enjoyment, satisfaction, subjective norms, descriptive norms, alternative attractiveness, the need for variety, change experience, and adaptation cost. This study contributes to IS theories in three important ways. Firstly, it shows IS switching should be included in IS post-adoption research together with IS continuance. Secondly, a modern IS is usually multi-functional and SNG players have multiple reasons for using a SNG, thus a player’s beliefs about the hedonic, social and utilitarian perceptions of their continued use of the SNG exert significant effects on the continuance intention. Thirdly, the determinants of the switch ing intention mainly exert push, pull, and mooring effects. Players’ beliefs about their current SNG and the available alternatives, as well as their individual characteristics are all significant determinants of the switching intention. SNG players combine these effects in order to formulate the switching intention. Finally, this study presents limitations and suggestions for future research.

Behavior of black liquor nitrogen in combustion : formation of cyanate

The Kraft pulping process is the dominant chemical pulping process in the world. Roughly 195 million metric tons of black liquor are produced annually as a by-product from the Kraft pulping process. Black liquor consists of spent cooking chemicals and dissolved organics from the wood and can contain up to 0.15 wt% nitrogen on dry solids basis. The cooking chemicals from black liquor are recovered in a chemical recovery cycle. Water is evaporated in the first stage of the chemical recovery cycle, so the black liquor has a dry solids content of 65-85% prior to combustion. During combustion of black liquor, a portion of the black liquor nitrogen is volatilized, finally forming N2 or NO. The rest of the nitrogen remains in the char as char nitrogen. During char conversion, fixed carbon is burned off leaving the pulping chemicals as smelt, and the char nitrogen forms mostly smelt nitrogen (cyanate, OCN-). Smelt exits the recovery boiler and is dissolved in water. The cyanate from smelt decomposes in the presence of water, forming NH3, which causes nitrogen emissions from the rest of the chemical recovery cycle. This thesis had two focuses: firstly, to determine how the nitrogen chemistry in the recovery boiler is affected by modification of black liquor; and secondly, to find out what causes cyanate formation during thermal conversion, and which parameters affect cyanate formation and decomposition during thermal conversion of black liquor. The fate of added biosludge nitrogen in chemical recovery was determined in Paper I. The added biosludge increased the nitrogen content of black liquor. At the pulp mill, the added biosludge did not increase the NO formation in the recovery boiler, but instead increased the amount of cyanate in green liquor. The increased cyanate caused more NH3 formation, which increased the NCG boiler’s NO emissions. Laboratory-scale experiments showed an increase in both NO and cyanate formation after biosludge addition. Black liquor can be modified, for example by addition of a solid biomass to increase the energy density of black liquor, or by separation of lignin from black liquor by precipitation. The precipitated lignin can be utilized in the production of green chemicals or as a fuel. In Papers II and III, laboratory-scale experiments were conducted to determine the impact of black liquor modification on NO and cyanate formation. Removal of lignin from black liquor reduced the nitrogen content of the black liquor. In most cases NO and cyanate formation decreased with increasing lignin removal; the exception was NO formation from lignin lean soda liquors. The addition of biomass to black liquor resulted in a higher nitrogen content fuel mixture, due to the higher nitrogen content of biomass compared to black liquor. More NO and cyanate were formed from the fuel mixtures than from pure black liquor. The increased amount of formed cyanate led to the hypothesis that black liquor is catalytically active and converts a portion of the nitrogen in the mixed fuel to cyanate. The mechanism behind cyanate formation during thermal conversion of black liquor was not clear before this thesis. Paper IV studies the cyanate formation of alkali metal loaded fuels during gasification in a CO2 atmosphere. The salts K2CO3, Na2CO3, and K2SO4 all promoted char nitrogen to cyanate conversion during gasification, while KCl and CaCO3 did not. It is now assumed that cyanate is formed when alkali metal carbonate or an active intermediate of alkali metal carbonate (e.g. -CO2K) reacts with the char nitrogen forming cyanate. By testing different fuels (bark, peat, and coal), each of which had a different form of organic nitrogen, it was concluded that the form of organic nitrogen in char also has an impact on cyanate formation. Cyanate can be formed during pyrolysis of black liquor, but at temperatures 900°C or above, the formed cyanate will decompose. Cyanate formation in gasifying conditions with different levels of CO2 in the atmosphere was also studied. Most of the char nitrogen was converted to cyanate during gasification at 800-900°C in 13-50% CO2 in N2, and only 5% of the initial fuel nitrogen was converted to NO during char conversion. The formed smelt cyanate was stable at 800°C 13% CO2, while it decomposed at 900°C 13% CO2. The cyanate decomposition was faster at higher temperatures and in oxygen-containing atmospheres than in an inert atmosphere. The presence of CO2 in oxygencontaining atmospheres slowed down the decomposition of cyanate. This work will provide new information on how modification of black liquor affects the nitrogen chemistry during thermal conversion of black liquor and what causes cyanate formation during thermal conversion of black liquor. The formation and decomposition of cyanate was studied in order to provide new data, which would be useful in modeling of nitrogen chemistry in the recovery boiler.

Large-eddy simulation of wind flows over complex terrains for wind energy applications

Wind energy has obtained outstanding expectations due to risks of global warming and nuclear energy production plant accidents. Nowadays, wind farms are often constructed in areas of complex terrain. A potential wind farm location must have the site thoroughly surveyed and the wind climatology analyzed before installing any hardware. Therefore, modeling of Atmospheric Boundary Layer (ABL) flows over complex terrains containing, e.g. hills, forest, and lakes is of great interest in wind energy applications, as it can help in locating and optimizing the wind farms. Numerical modeling of wind flows using Computational Fluid Dynamics (CFD) has become a popular technique during the last few decades. Due to the inherent flow variability and large-scale unsteadiness typical in ABL flows in general and especially over complex terrains, the flow can be difficult to be predicted accurately enough by using the Reynolds-Averaged Navier-Stokes equations (RANS). Large- Eddy Simulation (LES) resolves the largest and thus most important turbulent eddies and models only the small-scale motions which are more universal than the large eddies and thus easier to model. Therefore, LES is expected to be more suitable for this kind of simulations although it is computationally more expensive than the RANS approach. With the fast development of computers and open-source CFD software during the recent years, the application of LES toward atmospheric flow is becoming increasingly common nowadays. The aim of the work is to simulate atmospheric flows over realistic and complex terrains by means of LES. Evaluation of potential in-land wind park locations will be the main application for these simulations. Development of the LES methodology to simulate the atmospheric flows over realistic terrains is reported in the thesis. The work also aims at validating the LES methodology at a real scale. In the thesis, LES are carried out for flow problems ranging from basic channel flows to real atmospheric flows over one of the most recent real-life complex terrain problems, the Bolund hill. All the simulations reported in the thesis are carried out using a new OpenFOAM® -based LES solver. The solver uses the 4th order time-accurate Runge-Kutta scheme and a fractional step method. Moreover, development of the LES methodology includes special attention to two boundary conditions: the upstream (inflow) and wall boundary conditions. The upstream boundary condition is generated by using the so-called recycling technique, in which the instantaneous flow properties are sampled on aplane downstream of the inlet and mapped back to the inlet at each time step. This technique develops the upstream boundary-layer flow together with the inflow turbulence without using any precursor simulation and thus within a single computational domain. The roughness of the terrain surface is modeled by implementing a new wall function into OpenFOAM® during the thesis work. Both, the recycling method and the newly implemented wall function, are validated for the channel flows at relatively high Reynolds number before applying them to the atmospheric flow applications. After validating the LES model over simple flows, the simulations are carried out for atmospheric boundary-layer flows over two types of hills: first, two-dimensional wind-tunnel hill profiles and second, the Bolund hill located in Roskilde Fjord, Denmark. For the twodimensional wind-tunnel hills, the study focuses on the overall flow behavior as a function of the hill slope. Moreover, the simulations are repeated using another wall function suitable for smooth surfaces, which already existed in OpenFOAM® , in order to study the sensitivity of the flow to the surface roughness in ABL flows. The simulated results obtained using the two wall functions are compared against the wind-tunnel measurements. It is shown that LES using the implemented wall function produces overall satisfactory results on the turbulent flow over the two-dimensional hills. The prediction of the flow separation and reattachment-length for the steeper hill is closer to the measurements than the other numerical studies reported in the past for the same hill geometry. The field measurement campaign performed over the Bolund hill provides the most recent field-experiment dataset for the mean flow and the turbulence properties. A number of research groups have simulated the wind flows over the Bolund hill. Due to the challenging features of the hill such as the almost vertical hill slope, it is considered as an ideal experimental test case for validating micro-scale CFD models for wind energy applications. In this work, the simulated results obtained for two wind directions are compared against the field measurements. It is shown that the present LES can reproduce the complex turbulent wind flow structures over a complicated terrain such as the Bolund hill. Especially, the present LES results show the best prediction of the turbulent kinetic energy with an average error of 24.1%, which is a 43% smaller than any other model results reported in the past for the Bolund case. Finally, the validated LES methodology is demonstrated to simulate the wind flow over the existing Muukko wind farm located in South-Eastern Finland. The simulation is carried out only for one wind direction and the results on the instantaneous and time-averaged wind speeds are briefly reported. The demonstration case is followed by discussions on the practical aspects of LES for the wind resource assessment over a realistic inland wind farm.

Unequal Teeth Widths for Torque Ripple Reduction in Permanent Magnet Synchronous Machines With Fractional-Slot Non-Overlapping Windings

Permanent magnet synchronous machines with fractional-slot non-overlapping windings (FSPMSM), also known as tooth-coil winding permanent magnet synchronous machines (TCW PMSM), have been under intensive research during the latest decade. There are many optimization routines explained and implemented in the literature in order to improve the characteristics of this machine type. This paper introduces a new technique for torque ripple minimization in TCW PMSM. The source of torque harmonics is also described. The low order torque harmonics can be harmful for a variety of applications, such as direct drive wind generators, direct drive light vehicle electrical motors, and for some high precision servo applications. The reduction of the torque ripple harmonics with the lowest orders (6th and 12th) is realized by machine geometry optimization technique using finite element analysis (FEA). The presented optimization technique includes the stator geometry adjustment in TCW PMSMs with rotor surface permanent magnets and with rotor embedded permanent magnets. Influence of the permanent magnet skewing on the torque ripple reduction and cogging torque elimination was also investigated. It was implemented separately and together with the stator optimization technique. As a result, the reduction of some torque ripple harmonics was attained.

Explaining the intention to play and behavior of playing sports betting games of young Finnish adults : an application of the theory of planned behavior

The aim of this Master’s Thesis was to examine the determinants of intention and behavior of playing sports betting games in order to explain the intention to play in a more precise way and to be able to understand the behavior of playing. The theory of planned behavior was applied in explaining the intention of young Finnish adults aged 18 to 34. A quantitative research method was applied and an online survey was sent to the students of Lappeenranta University of Technology and to the subscribers of Urheilulehti in order to reach a sample that present the young population of Finland. The theory of the study focused on the theory of planned behavior and its antecedents, attitude towards behavior, subjective norms, perceived behavioral control as well as motivation. By analyzing the data, causal relationships were found through which the explanation of intention was possible. The results showed that attitude towards playing, subjective norms, perceived behavioral control and motivation impact the formation of intention significantly. The results also indicated that intention impacts significantly to the playing frequency.

Effects of Fabrication Processes on the Behavior of S960 Ultra High Strength Steel (UHSS)

Strenx® 960 MC is a direct quenched type of Ultra High Strength Steel (UHSS) with low carbon content. Although this material combines high strength and good ductility, it is highly sensitive towards fabrication processes. The presence of stress concentration due to structural discontinuity or notch will highlight the role of these fabrication effects on the deformation capacity of the material. Due to this, a series of tensile tests are done on both pure base material (BM) and when it has been subjected to Heat Input (HI) and Cold Forming (CF). The surface of the material was dressed by laser beam with a certain speed to study the effect of HI while the CF is done by bending the specimen to a certain angle prior to tensile test. The generated results illustrate the impact of these processes on the deformation capacity of the material, specially, when the material has HI experience due to welding or similar processes. In order to compare the results with those of numerical simulation, LS-DYNA explicit commercial package has been utilized. The generated results show an acceptable agreement between experimental and numerical simulation outcomes.

Facilitating corporate entrepreneurial behavior: A study of corporate entrepreneurial behavior in corporate banking

This study discusses the pronounced importance of corporate entrepreneurial behavior, CEB, facilitation and enablement as a key dimension in the rapidly changing business environment within companies. The research target is a large finance company in Finland, where regulations, compliance and processes restrict and refine extensively business approach. The purpose of this study is to foster the understanding of corporate entrepreneurial behavior and requirements and identify the supporters and inhibitors of facilitation of it. Furthermore, this study examines who should be driving the implementation and offer concrete outcome for the company to get the facilitation started and berth it as part of the organizational culture and values. The theoretical background is constructed from literature related to concept of corporate entrepreneurial behavior, factors supporting and hindering the facilitation based on previous studies and innovation management. Furthermore theoretical framework of middle managers entrepreneurial behavior in facilitation process was researched. Additionally top down and bottom up approach of conversational space building within the organization in order to foster innovation and involving mindset and behavior was in the core literature. The empirical research conducted for the study consists three parts; innovation audit questionnaire, semi-structured interviews and secondary data from previously made research within the case company. Questionnaire and interviews were targeted to eight middle managers within the company, the head of branch regions in corporate segment. The secondary data was collected from over 300 employees in the case company by an external company. Research results were analyzed mainly by themes and source division in adaption with the theoretical framework. The study finds that facilitation of CEB should be a strategic choice and requires strong management support and examples. Behavior should be involved with organizational culture, values, structures and processes. The companies´ willingness to take risks and encourage employees at all levels to participate and be involved by taking ownership and responsibility is in the core. CEB is found to be a key dimension in increasing employee satisfaction and engagement, competitive advantages and economic growth of companies. There is increased interest towards CEB in the case company but there is lack in the mutual consensus of it. CEB is not in the strategy although the mindset and support from management is in place. There is no concrete enablement and space for innovation and CEB although the platform would be receptive. Further research is needed to build shared vision of CEB and how to make it a part of the organizational culture and values in addition to building the conversational space.

Consumer Behavior in Mortgage Market: Evidence from Russia

The purpose of this master thesis is to identify behavioral patterns of potential borrower in mortgage market in crisis conditions and to link mortgage products available on Russian market with potential borrowers segments in dependence of detected patterns. Empirical results achieved through 172 answers of potential borrowers allowed to classify them in four groups in dependence of respondent perceptions about mortgage and future. On the basis of literature review and currently state of Russian mortgage market particular mortgage products were suggested to each of four clusters of potential borrowers. Then, recommendations for Russian banks how to apply received results were developed. Current master thesis has strong both academic and managerial contributions. It it adds significant value to existing consumer behavior studies; and provides practical recommendations for Russian banks how to understand mortgage borrower behavior in order to increase trust to mortgage among population.