Selective catalytic reduction of nitrogen oxides with ammonia in forced unsteady state reactors - Case based reasoning and mathematical model simulation reasoning

The application of forced unsteady-state reactors in case of selective catalytic reduction of nitrogen oxides (NOx) with ammonia (NH3) is sustained by the fact that favorable temperature and composition distributions which cannot be achieved in any steady-state regime can be obtained by means of unsteady-state operations. In a normal way of operation the low exothermicity of the selective catalytic reduction (SCR) reaction (usually carried out in the range of 280-350°C) is not enough to maintain by itself the chemical reaction. A normal mode of operation usually requires supply of supplementary heat increasing in this way the overall process operation cost. Through forced unsteady-state operation, the main advantage that can be obtained when exothermic reactions take place is the possibility of trapping, beside the ammonia, the moving heat wave inside the catalytic bed. The unsteady state-operation enables the exploitation of the thermal storage capacity of the catalyticbed. The catalytic bed acts as a regenerative heat exchanger allowing auto-thermal behaviour when the adiabatic temperature rise is low. Finding the optimum reactor configuration, employing the most suitable operation model and identifying the reactor behavior are highly important steps in order to configure a proper device for industrial applications. The Reverse Flow Reactor (RFR) - a forced unsteady state reactor - corresponds to the above mentioned characteristics and may be employed as an efficient device for the treatment of dilute pollutant mixtures. As a main disadvantage, beside its advantages, the RFR presents the 'wash out' phenomena. This phenomenon represents emissions of unconverted reactants at every switch of the flow direction. As a consequence our attention was focused on finding an alternative reactor configuration for RFR which is not affected by the incontrollable emissions of unconverted reactants. In this respect the Reactor Network (RN) was investigated. Its configuration consists of several reactors connected in a closed sequence, simulating a moving bed by changing the reactants feeding position. In the RN the flow direction is maintained in the same way ensuring uniformcatalyst exploitation and in the same time the 'wash out' phenomena is annulated. The simulated moving bed (SMB) can operate in transient mode giving practically constant exit concentration and high conversion levels. The main advantage of the reactor network operation is emphasizedby the possibility to obtain auto-thermal behavior with nearly uniformcatalyst utilization. However, the reactor network presents only a small range of switching times which allow to reach and to maintain an ignited state. Even so a proper study of the complex behavior of the RN may give the necessary information to overcome all the difficulties that can appear in the RN operation. The unsteady-state reactors complexity arises from the fact that these reactor types are characterized by short contact times and complex interaction between heat and mass transportphenomena. Such complex interactions can give rise to a remarkable complex dynamic behavior characterized by a set of spatial-temporal patterns, chaotic changes in concentration and traveling waves of heat or chemical reactivity. The main efforts of the current research studies concern the improvement of contact modalities between reactants, the possibility of thermal wave storage inside the reactor and the improvement of the kinetic activity of the catalyst used. Paying attention to the above mentioned aspects is important when higher activity even at low feeding temperatures and low emissions of unconverted reactants are the main operation concerns. Also, the prediction of the reactor pseudo or steady-state performance (regarding the conversion, selectivity and thermal behavior) and the dynamicreactor response during exploitation are important aspects in finding the optimal control strategy for the forced unsteady state catalytic tubular reactors. The design of an adapted reactor requires knowledge about the influence of its operating conditions on the overall process performance and a precise evaluation of the operating parameters rage for which a sustained dynamic behavior is obtained. An apriori estimation of the system parameters result in diminution of the computational efforts. Usually the convergence of unsteady state reactor systems requires integration over hundreds of cycles depending on the initial guess of the parameter values. The investigation of various operation models and thermal transfer strategies give reliable means to obtain recuperative and regenerative devices which are capable to maintain an auto-thermal behavior in case of low exothermic reactions. In the present research work a gradual analysis of the SCR of NOx with ammonia process in forced unsteady-state reactors was realized. The investigation covers the presentationof the general problematic related to the effect of noxious emissions in the environment, the analysis of the suitable catalysts types for the process, the mathematical analysis approach for modeling and finding the system solutions and the experimental investigation of the device found to be more suitable for the present process. In order to gain information about the forced unsteady state reactor design, operation, important system parameters and their values, mathematical description, mathematicalmethod for solving systems of partial differential equations and other specific aspects, in a fast and easy way, and a case based reasoning (CBR) approach has been used. This approach, using the experience of past similarproblems and their adapted solutions, may provide a method for gaining informations and solutions for new problems related to the forced unsteady state reactors technology. As a consequence a CBR system was implemented and a corresponding tool was developed. Further on, grooving up the hypothesis of isothermal operation, the investigation by means of numerical simulation of the feasibility of the SCR of NOx with ammonia in the RFRand in the RN with variable feeding position was realized. The hypothesis of non-isothermal operation was taken into account because in our opinion ifa commercial catalyst is considered, is not possible to modify the chemical activity and its adsorptive capacity to improve the operation butis possible to change the operation regime. In order to identify the most suitable device for the unsteady state reduction of NOx with ammonia, considering the perspective of recuperative and regenerative devices, a comparative analysis of the above mentioned two devices performance was realized. The assumption of isothermal conditions in the beginningof the forced unsteadystate investigation allowed the simplification of the analysis enabling to focus on the impact of the conditions and mode of operation on the dynamic features caused by the trapping of one reactant in the reactor, without considering the impact of thermal effect on overall reactor performance. The non-isothermal system approach has been investigated in order to point out the important influence of the thermal effect on overall reactor performance, studying the possibility of RFR and RN utilization as recuperative and regenerative devices and the possibility of achieving a sustained auto-thermal behavior in case of lowexothermic reaction of SCR of NOx with ammonia and low temperature gasfeeding. Beside the influence of the thermal effect, the influence of the principal operating parameters, as switching time, inlet flow rate and initial catalyst temperature have been stressed. This analysis is important not only because it allows a comparison between the two devices and optimisation of the operation, but also the switching time is the main operating parameter. An appropriate choice of this parameter enables the fulfilment of the process constraints. The level of the conversions achieved, the more uniform temperature profiles, the uniformity ofcatalyst exploitation and the much simpler mode of operation imposed the RN as a much more suitable device for SCR of NOx with ammonia, in usual operation and also in the perspective of control strategy implementation. Theoretical simplified models have also been proposed in order to describe the forced unsteady state reactors performance and to estimate their internal temperature and concentration profiles. The general idea was to extend the study of catalytic reactor dynamics taking into account the perspectives that haven't been analyzed yet. The experimental investigation ofRN revealed a good agreement between the data obtained by model simulation and the ones obtained experimentally.

A new heuristic method for solving spatially constrained forest planning problems based on mitigation of infeasibilities radiating outward from a forced choice

[Abstract]

Capacity of riparian buffer zones to reduce sediment concentrations in discharge from peatlands drained for forestry

Abstract

Timing of Capacity Change: Models for Capital Intensive Industry

The suitable timing of capacity investments is a remarkable issue especially in capital intensive industries. Despite its importance, fairly few studies have been published on the topic. In the present study models for the timing of capacity change in capital intensive industry are developed. The study considers mainly the optimal timing of single capacity changes. The review of earlier research describes connections between cost, capacity and timing literature, and empirical examples are used to describe the starting point of the study and to test the developed models. The study includes four models, which describe the timing question from different perspectives. The first model, which minimizes unit costs, has been built for capacity expansion and replacement situations. It is shown that the optimal timing of an investment can be presented with the capacity and cost advantage ratios. After the unit cost minimization model the view is extended to the direction of profit maximization. The second model states that early investments are preferable if the change of fixed costs is small compared to the change of the contribution margin. The third model is a numerical discounted cash flow model, which emphasizes the roles of start-up time, capacity utilization rate and value of waiting as drivers of the profitable timing of a project. The last model expands the view from project level to company level and connects the flexibility of assets and cost structures to the timing problem. The main results of the research are the solutions of the models and analysis or simulations done with the models. The relevance and applicability of the results are verified by evaluating the logic of the models and by numerical cases.

Modeling and Simulation ofReal-Time System as a Tool to Improve Capacity Management - Case Fenix

Tämän tutkimustyön kohteena on TietoEnator Oy:n kehittämän Fenix-tietojärjestelmän kapasiteettitarpeen ennustaminen. Työn tavoitteena on tutustua Fenix-järjestelmän eri osa-alueisiin, löytää tapa eritellä ja mallintaa eri osa-alueiden vaikutus järjestelmän kuormitukseen ja selvittää alustavasti mitkä parametrit vaikuttavat kyseisten osa-alueiden luomaan kuormitukseen. Osa tätä työtä on tutkia eri vaihtoehtoja simuloinnille ja selvittää eri vaihtoehtojen soveltuvuus monimutkaisten järjestelmien mallintamiseen. Kerätyn tiedon pohjaltaluodaan järjestelmäntietovaraston kuormitusta kuvaava simulaatiomalli. Hyödyntämällä mallista saatua tietoa ja tuotantojärjestelmästä mitattua tietoa mallia kehitetään vastaamaan yhä lähemmin todellisen järjestelmän toimintaa. Mallista tarkastellaan esimerkiksi simuloitua järjestelmäkuormaa ja jonojen käyttäytymistä. Tuotantojärjestelmästä mitataan eri kuormalähteiden käytösmuutoksia esimerkiksi käyttäjämäärän ja kellonajan suhteessa. Tämän työn tulosten on tarkoitus toimia pohjana myöhemmin tehtävälle jatkotutkimukselle, jossa osa-alueiden parametrisointia tarkennetaan lisää, mallin kykyä kuvata todellista järjestelmää tehostetaanja mallin laajuutta kasvatetaan.

Absorptive capacity and the effect of social integration mechanisms in knowledge utilization

Tiedosta on tullut määräävä tekijä yrityksensuorituskyvylle. Yritykset hankkivat aktiivisesti uutta tietoa ulkoisesta ympäristöstään ja tallentavat sitä tietokantoihinsa. Uusi tieto on innovaatioiden ja uusien ideoiden peruselementti. Uudet ideat pitää myös kaupallistaa, jotta niiden avulla voidaan hankkia kilpailuetua. Absorptiivisen kapasiteetin malli yhdistää tiedon prosessointiin liittyvät kyvykkyydet, jotka vaikuttavat yrityksen kykyyn hyödyntää tietoa tehokkaasti. Ennen kuin tietoa voidaan käyttää uusien tuotteiden ja palveluiden luomiseen, täytyy sitä jakaa yrityksessä ja muuttaa se yrityksen toimintaa palvelevaksi. Aiemmissa tutkimuksissa innovaatiot ovat vahvasti liitetty yrityksen kykyyn uudistua. Tämä pro gradu -tutkielma tutkii sosiaalisten integraatiomekanismien vaikutusta potentiaalisen absorptiivisen kapasiteetin muuttamiseen toteutuneeksi absorptiiviseksi kapasiteetiksi. Yksilöiden ja osastojen välisen yhteistyön sekä luottamuksen vaikutus tiedon sisäistämiseen tutkittiin. Tutkielma pohjautuu monikansallisessa yrityksessä keväällä 2006 suoritettuun uudistumiskyky-tutkimukseen. Tutkielma keskittyy yrityksen kykyyn uudistua uuden tiedon ja innovaatioiden avulla. Tutkielma on kvantitatiivinen tapaustutkimus. Tutkielmassa tehtyjen havaintojen mukaan sosiaaliset integraatiomekanismit ovat tärkeitä uuden tiedon hyödyntämisessä. Tiedon eksplisiittyyden havaitaan vaikuttavan tiedon muuttamiseen yritykselle hyödylliseksi resurssiksi.

Deregulation of Railroads and Future Development Scenarios in Europe - Literature Analysis of Privatization Process Taken Place in US, UK and Sweden

Euroopan unionissa päätettiin jo yli vuosikymmen sitten, että rautatieliiketoiminta vapautetaan kilpailulle. Iso-Britanniasta olimäärä tulla esimerkkivaltio tämän prosessin käyttöönotossa. Pääideana oli säännöstelyn keventäminen, jolloin omistuspohja toimialalla laajenee ja rautateiden infrastruktuuri sekä toiminta parantuvat. Infrastruktuuri on määrä olla yhden organisaation hallinnassa ja raiteiden käyttöoikeus on kaikilla lupaehdot täyttävillä operaattoreilla, jotka kilpailevat keskenään matkustajista ja tavararahdeista. Kuitenkin Yhdysvalloissa ja eräissä Latinalaisen Amerikan maissa kilpailu on vapautettu siten, että rautatieyritys omistaa raideinfrastruktuurin, junat, tavarankuljetus- sekä matkustajavaunut. Iso-Britannian yksityistämistä pidettiin aluksi isonaepäonnistumisena: nopealla aikataululla sovellettiin jäykkiä transaktioperusteisia ulkoistamisstrategioita infrastruktuurin kunnossapitoon, jotka lopulta johtivat junien jatkuviin myöhästymisiin ja muutamaan tuhoisaan onnettomuuteen. Liiketoiminnallisessa mielessäkään ei oikein onnistuttu: infrastruktuurista vastaava yritys jouduttiin listaamaan pois Lontoon pörssistä, ja hallituksen oli pakko luoda tukipaketti pahasti velkaantuneen, vain marginaalisien investointien kohteena olleen yrityksen toimintaa varten (vaikka kapasiteettitarvetta oli markkinoilla). Myös rautatieoperaattorit olivat taloudellisessa ahdingossa ja vain määrätietoisten hallituksen laatimien pelastuspakettien avulla ala nousi syvimmästä kriisistään. Tästä huolimatta näiden negatiivisten sivuvaikutusten ohella koko ala pystyi kasvattamaan kysyntää, niin matkustaja- kuin rahtiliikenteenkin osalta. Vähenevän kysynnän trendi, joka alkoi 1970-luvulla, otti käännöksen parempaan. Toinen eurooppalaismaa, jolla on pitkät kokemukset yksityistämisestä, on Ruotsi. Tämä maatapaus on melko konservatiivinen verrattuna tilanteeseen edellisessä; vain rajattu määrä reittejä on avattu kilpailulle ja sopimukset tehdään kerralla pitkäksi aikaa eteenpäin. Ruotsin säännöstelyn purku osoittautui menestykseksi, koska tuottavuus onollut vakaassa kasvussa ja rautateiden markkinaosuus erityisesti matkustajapuolella on noussut merkittävästi, verrattuna muihin kuljetusmuotoihin. Kuitenkin kilpailua on käytännössä vähän tässä maassa ja parempiatuloksia on lupa odottaa, kun vain säännöstelyn purkaminen jatkuu. Viimeinen tutkimuksemme kohteena oleva maa on Yhdysvallat, joka alistutti rautatiet kilpailulle jo 1980-luvun alussa, käyttäen jo edellä mainittua vertikaalista integraatiota; tämä valinta on taas johtanut hyvin erilaisiin tuloksiin. Vaihtoehtoinen rakenteellinen uudistustapa on suosinut rahtivirtoja matkustajiin nähden, ja lopputuloksena tämä tapaus synnytti yrityksiä huolehtimaan toista näistä kahdesta pääasiakasryhmästä. Viimeaikaiset tulokset tästä yksityistämisprosessista ovat olleet hyviä: jäljellejääneiden yritysten voitot ovat kasvaneet, osinkoja ollaan kyetty jakamaan ja osakkeiden arvostus on noussut. Tässä tutkimusraportissa yritämme kolmen maatapauksen kautta esittää, miten yksityistämisprosessi tulee vaikuttamaan Euroopassa, kun kilpailu rautateillä vapautuu. Me käymmeläpi, mikä näistä kolmesta maaesimerkistä on kaikkein todennäköisin jaesitämme ehdotuksia siihen, miten valtiot voisivat välttää ei-haluttuja sivuvaikutuksia. Kolme maaesimerkkiä, ja lopuksi esitetty lyhyt tilastollinen analyysi osoittavat, että rautateillä on tulevaisuuden potentiaalia Euroopassa, ja kilpailun vapauttaminen on avain tämän potentiaalin realisointiin.

On the innovation capacity of technologyrelated knowledge-intensive business services. A case study of the technology and engineering consulting (TEC) sector in Singapore

Even though the research on innovation in services has expanded remarkably especially during the past two decades, there is still a need to increase understanding on the special characteristics of service innovation. In addition to studying innovation in service companies and industries, research has also recently focused more on services in innovation, as especially the significance of so-called knowledge intensive business services (KIBS) for the competitive edge of their clients, othercompanies, regions and even nations has been proved in several previous studies. This study focuses on studying technology-based KIBS firms, and technology andengineering consulting (TEC) sector in particular. These firms have multiple roles in innovation systems, and thus, there is also a need for in-depth studies that increase knowledge about the types and dimensions of service innovations as well as underlying mechanisms and procedures which make the innovations successful. The main aim of this study is to generate new knowledge in the fragmented research field of service innovation management by recognizing the different typesof innovations in TEC services and some of the enablers of and barriers to innovation capacity in the field, especially from the knowledge management perspective. The study also aims to shed light on some of the existing routines and new constructions needed for enhancing service innovation and knowledge processing activities in KIBS companies of the TEC sector. The main samples of data in this research include literature reviews and public data sources, and a qualitative research approach with exploratory case studies conducted with the help of the interviews at technology consulting companies in Singapore in 2006. These complement the qualitative interview data gathered previously in Finland during a larger research project in the years 2004-2005. The data is also supplemented by a survey conducted in Singapore. The respondents for the survey by Tan (2007) were technology consulting companies who operate in the Singapore region. The purpose ofthe quantitative part of the study was to validate and further examine specificaspects such as the influence of knowledge management activities on innovativeness and different types of service innovations, in which the technology consultancies are involved. Singapore is known as a South-east Asian knowledge hub and is thus a significant research area where several multinational knowledge-intensive service firms operate. Typically, the service innovations identified in the studied TEC firms were formed by several dimensions of innovations. In addition to technological aspects, innovations were, for instance, related to new client interfaces and service delivery processes. The main enablers of and barriers to innovation seem to be partly similar in Singaporean firms as compared to the earlier study of Finnish TEC firms. Empirical studies also brought forth the significance of various sources of knowledge and knowledge processing activities as themain driving forces of service innovation in technology-related KIBS firms. A framework was also developed to study the effect of knowledge processing capabilities as well as some moderators on the innovativeness of TEC firms. Especially efficient knowledge acquisition and environmental dynamism seem to influence the innovativeness of TEC firms positively. The results of the study also contributeto the present service innovation literature by focusing more on 'innovation within KIBs' rather than 'innovation through KIBS', which has been the typical viewpoint stressed in the previous literature. Additionally, the study provides several possibilities for further research.

Dehulling capacity and storability of naked oat

Selostus: Paljasjyväisen kauran kuoriutuvuus ja säilyvyys

Development of a PC Tool for Estimating Pressure Drops in Forced-convection Boiler Tubes

Kaksifaasivirtauksen kuvaamiseen käytettävät mallit, ja menetelmät kaksifaasivirtauksen painehäviön määrittämiseksi kehittyvät yhä monimutkaisimmiksi. Höyrystinputkissa tapahtuvien painehäviöiden arvioinnin vaatiman laskennan suorittamiseksi tietokoneohjelman kehittäminen on välttämätöntä. Tässä työssä on kehitetty itsenäinen PC-ohjelma painehäviöiden arvioimiseksi pakotetulle konvektiovirtaukselle pystysuorissa höyrykattilan höyrystinputkissa. Veden ja vesihöyryn aineominaisuuksien laskentaan käytetään IAPWS-IF97 –yhtälökokoelmaa sekä muita tarvittavia IAPWS:n suosittelemia yhtälöitä. Höyrystinputkessa kulloinkin vallitsevan virtausmuodon määrittämiseen käytetään sovelluskelpoisia virtausmuotojen välisiä rajoja kuvaavia yhtälöitä. Ohjelmassa käytetään painehäviön määritykseen kirjallisuudessa julkaistuja yhtälöitä, virtausmuodosta riippuen, alijäähtyneelle virtaukselle, kupla-, tulppa- ja rengasvirtaukselle sekä tulistetun höyryn virtaukselle. Ohjelman laskemia painehäviöarvioita verrattiin kirjallisuudesta valittuihin mittaustuloksiin. Laskettujen painehäviöiden virhe vaihteli välillä –19.5 ja +23.9 %. Virheiden itseisarvojen keskiarvo oli 12.8 %.

Evolution of Ba and Role of Absorptive Capacity in Collaboration between MNCs and Chinese Universities in China

During the recent years, collaboration with Chinese universities has aroused growing interest among multinational companies (MNCs). Cross-cultural university-industry (U-I) collaboration creates various challenges in collaborative knowledge creation and innovation due to the differences e.g. between university and company motivation, objectives and activities. Also different values, norms, and means of actions result often in collisions and misunderstandings. This thesis examines the establishment of the relationships and the evolution of the collaboration between MNCs and Chinese universities. Empirical findings underscore that the partners in collaboration are required to possess research interest as well as capability to acquire, assimilate and exploit new external knowledge. Time and communication have a critical role in the evolution of the collaboration. In China the personal relationships, guanxi, play an important role. Collaborative knowledge creation requires a platform, Ba, which enables the creation of common understanding, commitment, trust and mutual respect. Empirical data has been collected through interviewing company experts and academe of Chinese universities from ICT and forest industries as well as attending panel discussions and meetings with the experts from the field of study.

Type II aromatic polyketide biosynthetic tailoring enzymes: diversity and adaptation in Streptomyces secondary metabolism.

Members of the bacterial genus Streptomyces are well known for their ability to produce an exceptionally wide selection of diverse secondary metabolites. These include natural bioactive chemical compounds which have potential applications in medicine, agriculture and other fields of commerce. The outstanding biosynthetic capacity derives from the characteristic genetic flexibility of Streptomyces secondary metabolism pathways: i) Clustering of the biosynthetic genes in chromosome regions redundant for vital primary functions, and ii) the presence of numerous genetic elements within these regions which facilitate DNA rearrangement and transfer between non-progeny species. Decades of intensive genetic research on the organization and function of the biosynthetic routes has led to a variety of molecular biology applications, which can be used to expand the diversity of compounds synthesized. These include techniques which, for example, allow modification and artificial construction of novel pathways, and enable gene-level detection of silent secondary metabolite clusters. Over the years the research has expanded to cover molecular-level analysis of the enzymes responsible for the individual catalytic reactions. In vitro studies of the enzymes provide a detailed insight into their catalytic functions, mechanisms, substrate specificities, interactions and stereochemical determinants. These are factors that are essential for the thorough understanding and rational design of novel biosynthetic routes. The current study is a part of a more extensive research project (Antibiotic Biosynthetic Enzymes; www.sci.utu.fi/projects/biokemia/abe), which focuses on the post-PKS tailoring enzymes involved in various type II aromatic polyketide biosynthetic pathways in Streptomyces bacteria. The initiative here was to investigate specific catalytic steps in anthracycline and angucycline biosynthesis through in vitro biochemical enzyme characterization and structural enzymology. The objectives were to elucidate detailed mechanisms and enzyme-level interactions which cannot be resolved by in vivo genetic studies alone. The first part of the experimental work concerns the homologous polyketide cyclases SnoaL and AknH. These catalyze the closure of the last carbon ring of the tetracyclic carbon frame common to all anthracycline-type compounds. The second part of the study primarily deals with tailoring enzymes PgaE (and its homolog CabE) and PgaM, which are responsible for a cascade of sequential modification reactions in angucycline biosynthesis. The results complemented earlier in vivo findings and confirmed the enzyme functions in vitro. Importantly, we were able to identify the amino acid -level determinants that influence AknH and SnoaL stereoselectivity and to determine the complex biosynthetic steps of the angucycline oxygenation cascade of PgaE and PgaM. In addition, the findings revealed interesting cases of enzyme-level adaptation, as some of the catalytic mechanisms did not coincide with those described for characterised homologs or enzymes of known function. Specifically, SnoaL and AknH were shown to employ a novel acid-base mechanism for aldol condenzation, whereas the hydroxylation reaction catalysed by PgaM involved unexpected oxygen chemistry. Owing to a gene-level fusion of two ancestral reading frames, PgaM was also shown to adopt an unusual quaternary sturucture, a non-covalent fusion complex of two alternative forms of the protein. Furthermore, the work highlighted some common themes encountered in polyketide biosynthetic pathways such as enzyme substrate specificity and intermediate reactivity. These are discussed in the final chapters of the work.

Competence Development and Capacity Building of Sawmill Enterprises in Kenya – A Human Resources Development Approach

The Kenyan forestry and sawmilling industry have been subject to a changing environment since 1999 when the industrial forest plantations were closed down. This has lowered raw material supply and it has affected and reduced the sawmill operations and the viability of the sawmill enterprises. The capacity of the 276 registered sawmills is not sufficient to fulfill sawn timber demand in Kenya. This is because of the technological degradation and lack of a qualified labor force, which were caused because of non-existent sawmilling education and further training in Kenya. Lack of competent sawmill workers has led to low raw material recovery, under utilization of resources and loss of employment. The objective of the work was to suggest models, methods and approaches for the competence and capacity development of the Kenyan sawmilling industry, sawmills and their workers. A nationwide field survey, interviews, questionnaire and literature review was used for data collection to find out the sawmills’ competence development areas and to suggest models and methods for their capacity building. The sampling frame included 22 sawmills that represented 72,5% of all the registered sawmills in Kenya. The results confirmed that the sawmills’ technological level was backwards, productivity low, raw material recovery unacceptable and workers’ professional education low. The future challenges will be how to establish the sawmills’ capacity building and workers’ competence development. Sawmilling industry development requires various actions through new development models and approaches. Activities should be started for technological development and workers’ competence development. This requires re-starting of vocational training in sawmilling and the establishment of more effective co-operation between the sawmills and their stakeholder groups. In competence development the Enterprise Competence Management Model of Nurminen (2007) can be used, whereas the best training model and approach would be a practically oriented learning at work model in which the short courses, technical assistance and extension services would be the key functions.