Central auditory processing and the acquisition of phonology in 2-year-old children with recurrent acute otitis media

Middle ear infections (acute otitis media, AOM) are among the most common infectious diseases in childhood, their incidence being greatest at the age of 6–12 months. Approximately 10–30% of children undergo repetitive periods of AOM, referred to as recurrent acute otitis media (RAOM). Middle ear fluid during an AOM episode causes, on average, 20–30 dB of hearing loss lasting from a few days to as much as a couple of months. It is well known that even a mild permanent hearing loss has an effect on language development but so far there is no consensus regarding the consequences of RAOM on childhood language acquisition. The results of studies on middle ear infections and language development have been partly discrepant and the exact effects of RAOM on the developing central auditory nervous system are as yet unknown. This thesis aims to examine central auditory processing and speech production among 2-year-old children with RAOM. Event-related potentials (ERPs) extracted from electroencephalography can be used to objectively investigate the functioning of the central auditory nervous system. For the first time this thesis has utilized auditory ERPs to study sound encoding and preattentive auditory discrimination of speech stimuli, and neural mechanisms of involuntary auditory attention in children with RAOM. Furthermore, the level of phonological development was studied by investigating the number and the quality of consonants produced by these children. Acquisition of consonant phonemes, which are harder to hear than vowels, is a good indicator of the ability to form accurate memory representations of ambient language and has not been studied previously in Finnish-speaking children with RAOM. The results showed that the cortical sound encoding was intact but the preattentive auditory discrimination of multiple speech sound features was atypical in those children with RAOM. Furthermore, their neural mechanisms of auditory attention differed from those of their peers, thus indicating that children with RAOM are atypically sensitive to novel but meaningless sounds. The children with RAOM also produced fewer consonants than their controls. Noticeably, they had a delay in the acquisition of word-medial consonants and the Finnish phoneme /s/, which is acoustically challenging to perceive compared to the other Finnish phonemes. The findings indicate the immaturity of central auditory processing in the children with RAOM, and this might also emerge in speech production. This thesis also showed that the effects of RAOM on central auditory processing are long-lasting because the children had healthy ears at the time of the study. An effective neural network for speech sound processing is a basic requisite of language acquisition, and RAOM in early childhood should be considered as a risk factor for language development.

Investigation of interface between Multimedia IP Network and Call Processing Server in 3G IP Telephony Core Network

The thesis presents an overview of third generation of IP telephony. The architecture of 3G IP Telephony and its components are described. The main goal of the thesis is to investigate the interface between the Call Processing Server and Multimedia IP Networks. The interface functionality, proposed protocol stack and a general description are presented in the thesis. To provide useful services, 3G IP Telephony requires a set of control protocols for connection establishment, capabilities exchange and conference control. The Session Initiation Protocol (SIP) and the H.323 are two protocols that meet these needs. In the thesis these two protocols are investigated and compared in terms of Complexity, Extensibility, Scalability, Services, Resource Utilization and Management.

Local Features in Image and Video Processing - Object Class Matching and Video Shot Detection

The usage of digital content, such as video clips and images, has increased dramatically during the last decade. Local image features have been applied increasingly in various image and video retrieval applications. This thesis evaluates local features and applies them to image and video processing tasks. The results of the study show that 1) the performance of different local feature detector and descriptor methods vary significantly in object class matching, 2) local features can be applied in image alignment with superior results against the state-of-the-art, 3) the local feature based shot boundary detection method produces promising results, and 4) the local feature based hierarchical video summarization method shows promising new new research direction. In conclusion, this thesis presents the local features as a powerful tool in many applications and the imminent future work should concentrate on improving the quality of the local features.

The importance of package design to Japanese consumers: The role of visual and informational elements of package design in decision making

The importance of package design as a marketing tool is growing as the competition in retail environment increases. However, there is a lack of studies on how each element of package design affects consumer decisions in different countries. The objective of this thesis is to study the role of package design to Japanese consumers. The research was conducted through an experiment with a sample of 37 Japanese female participants. They were divided into two groups and were given different tasks: one group had to choose a chocolate for themselves, and the other for a group of friends. The participants were presented with 15 different Finnish chocolate boxes to choose from. The qualitative data was gathered through observation and semi-structured interviews. In addition, data from questionnaires was quantified and all the data was triangulated. The empirical results suggest that visual elements strongly affect the decision making of Japanese consumers. Image was the most important element which acted as both, a visual and an informational aspect in the experiment. Informational elements on the other hand have little effect, especially when the context is written in a foreign language. However, informational elements affected participants who were choosing chocolates for a group of friends. A unique finding was the importance of kawaii (cuteness) to Japanese consumers.

Measuring Effectiveness of Marketing Message: The Role of Verbal, Visual and Brand Elements

The aim of this paper is to study the role of verbal, visual and brand elements while meas-uring effectiveness of marketing message. The thesis is written in the context of mobile gaming industry. The object of the study is marketing message. To achieve the aim, the main research question was formulated: How do the elements of marketing message, such as verbal, visual and brand, affect the consumer’s attitude toward the ad, emotional response and attention capture? The theory development chapter lays on three corner stones – analysis of previous litera-ture on marketing message and its elements, namely verbal, visual and brand; overview of literature on attitude formation and particularly attitude toward the ad. In addition, investiga-tion of key points of emotional response and attention capture literature finalizes the chap-ter. The empirical part consists of experiment, conducted with 27 participants. Experiment includes the self-report semantically anchored scale, measuring the attitude toward the ad, as well as autonomic measures – eye tracking (attention capture) and facial expressions (emotional response). The results of the experiment showed that the size of the brand element – the logo – has an effect on the attention capture and the overall attitude toward the ad. The bigger the logo, the more time people spend viewing it, and they realise the message is more educa-tional and factual. The measure related to the visual element – the visual complexity – in-creases the intensity of participant’s facial expression. While the measure of verbal ele-ment – the contrast between text and background colours – leads to a better attitude to-ward the ad. The higher the contrast between text and background, the more known the message appears to the viewer.

University students’ regulation of learning and text processing – examples from medical and teacher education

The general aim of the thesis was to study university students’ learning from the perspective of regulation of learning and text processing. The data were collected from the two academic disciplines of medical and teacher education, which share the features of highly scheduled study, a multidisciplinary character, a complex relationship between theory and practice and a professional nature. Contemporary information society poses new challenges for learning, as it is not possible to learn all the information needed in a profession during a study programme. Therefore, it is increasingly important to learn how to think and learn independently, how to recognise gaps in and update one’s knowledge and how to deal with the huge amount of constantly changing information. In other words, it is critical to regulate one’s learning and to process text effectively. The thesis comprises five sub-studies that employed cross-sectional, longitudinal and experimental designs and multiple methods, from surveys to eye tracking. Study I examined the connections between students’ study orientations and the ways they regulate their learning. In total, 410 second-, fourth- and sixth-year medical students from two Finnish medical schools participated in the study by completing a questionnaire measuring both general study orientations and regulation strategies. The students were generally deeply oriented towards their studies. However, they regulated their studying externally. Several interesting and theoretically reasonable connections between the variables were found. For instance, self-regulation was positively correlated with deep orientation and achievement orientation and was negatively correlated with non-commitment. However, external regulation was likewise positively correlated with deep orientation and achievement orientation but also with surface orientation and systematic orientation. It is argued that external regulation might function as an effective coping strategy in the cognitively loaded medical curriculum. Study II focused on medical students’ regulation of learning and their conceptions of the learning environment in an innovative medical course where traditional lectures were combined wth problem-based learning (PBL) group work. First-year medical and dental students (N = 153) completed a questionnaire assessing their regulation strategies of learning and views about the PBL group work. The results indicated that external regulation and self-regulation of the learning content were the most typical regulation strategies among the participants. In line with previous studies, self-regulation wasconnected with study success. Strictly organised PBL sessions were not considered as useful as lectures, although the students’ views of the teacher/tutor and the group were mainly positive. Therefore, developers of teaching methods are challenged to think of new solutions that facilitate reflection of one’s learning and that improve the development of self-regulation. In Study III, a person-centred approach to studying regulation strategies was employed, in contrast to the traditional variable-centred approach used in Study I and Study II. The aim of Study III was to identify different regulation strategy profiles among medical students (N = 162) across time and to examine to what extent these profiles predict study success in preclinical studies. Four regulation strategy profiles were identified, and connections with study success were found. Students with the lowest self-regulation and with an increasing lack of regulation performed worse than the other groups. As the person-centred approach enables us to individualise students with diverse regulation patterns, it could be used in supporting student learning and in facilitating the early diagnosis of learning difficulties. In Study IV, 91 student teachers participated in a pre-test/post-test design where they answered open-ended questions about a complex science concept both before and after reading either a traditional, expository science text or a refutational text that prompted the reader to change his/her beliefs according to scientific beliefs about the phenomenon. The student teachers completed a questionnaire concerning their regulation and processing strategies. The results showed that the students’ understanding improved after text reading intervention and that refutational text promoted understanding better than the traditional text. Additionally, regulation and processing strategies were found to be connected with understanding the science phenomenon. A weak trend showed that weaker learners would benefit more from the refutational text. It seems that learners with effective learning strategies are able to pick out the relevant content regardless of the text type, whereas weaker learners might benefit from refutational parts that contrast the most typical misconceptions with scientific views. The purpose of Study V was to use eye tracking to determine how third-year medical studets (n = 39) and internal medicine residents (n = 13) read and solve patient case texts. The results revealed differences between medical students and residents in processing patient case texts; compared to the students, the residents were more accurate in their diagnoses and processed the texts significantly faster and with a lower number of fixations. Different reading patterns were also found. The observed differences between medical students and residents in processing patient case texts could be used in medical education to model expert reasoning and to teach how a good medical text should be constructed. The main findings of the thesis indicate that even among very selected student populations, such as high-achieving medical students or student teachers, there seems to be a lot of variation in regulation strategies of learning and text processing. As these learning strategies are related to successful studying, students enter educational programmes with rather different chances of managing and achieving success. Further, the ways of engaging in learning seldom centre on a single strategy or approach; rather, students seem to combine several strategies to a certain degree. Sometimes, it can be a matter of perspective of which way of learning can be considered best; therefore, the reality of studying in higher education is often more complicated than the simplistic view of self-regulation as a good quality and external regulation as a harmful quality. The beginning of university studies may be stressful for many, as the gap between high school and university studies is huge and those strategies that were adequate during high school might not work as well in higher education. Therefore, it is important to map students’ learning strategies and to encourage them to engage in using high-quality learning strategies from the beginning. Instead of separate courses on learning skills, the integration of these skills into course contents should be considered. Furthermore, learning complex scientific phenomena could be facilitated by paying attention to high-quality learning materials and texts and other support from the learning environment also in the university. Eye tracking seems to have great potential in evaluating performance and growing diagnostic expertise in text processing, although more research using texts as stimulus is needed. Both medical and teacher education programmes and the professions themselves are challenging in terms of their multidisciplinary nature and increasing amounts of information and therefore require good lifelong learning skills during the study period and later in work life.

"Dov'è la sinistra?" Hemispatial neglect in stroke

As long as the incidence of stroke continues to grow, patients with large right hemisphere lesions suffering from hemispatial neglect will require neuropsychological evaluation and rehabilitation. The inability to process information especially that coming from the left side accompanied by the magnetic orientation to the ipsilesional side represents a real challenge for rehabilitation. This dissertation is concerned with crucial aspects in the clinical neuropsychological practice of hemispatial neglect. In studying the convergence of the visual and behavioural test batteries in the assessment of neglect, nine of the seventeen patients, who completed both the conventional subtests of the Behavioural Inattention Test and the Catherine Bergego Scale assessments, showed a similar severity of neglect and thus good convergence in both tests. However, patients with neglect and hemianopia had poorer scores in the line bisection test and they displayed stronger neglect in behaviour than patients with pure neglect. The second study examined, whether arm activation, modified from the Constraint Induced Movement Therapy, could be applied as neglect rehabilitation alone without any visual training. Twelve acute- or subacute patients were randomized into two rehabilitation groups: arm activation training or traditional voluntary visual scanning training. Neglect was ameliorated significantly or almost significantly in both training groups due to rehabilitation with the effect being maintained for at least six months. In studying the reflections of hemispatial neglect on visual memory, the associations of severity of neglect and visual memory performances were explored. The performances of acute and subacute patients with hemispatial neglect were compared with the performances of matched healthy control subjects. As hypothesized, encoding from the left side and immediate recall of visual material were significantly compromised in patients with neglect. Another mechanism of neglect affecting visual memory processes is observed in delayed visual reproduction. Delayed recall demands that the individual must make a match helped by a cue or it requires a search for relevant material from long-term memory storage. In the case of representational neglect, the search may succeed but the left side of the recollected memory still fails to open. Visual and auditory evoked potentials were measured in 21 patients with hemispatial neglect. Stimuli coming from the left or right were processed differently in both sensory modalities in acute and subacute patients as compared with the chronic patients. The differences equalized during the course of recovery. Recovery from hemispatial neglect was strongly associated with early rehabilitation and with the severity of neglect. Extinction was common in patients with neglect and it did not ameliorate with the recovery of neglect. The presence of pusher symptom hampered amelioration of visual neglect in acute and subacute stroke patients, whereas depression did not have any significant effect in the early phases after the stroke. However, depression had an unfavourable effect on recovery in the chronic phase. In conclusion, the combination of neglect and hemianopia may explain part of the residual behavioural neglect that is no longer evident in visual testing. Further research is needed in order to determine which specific rehabilitation procedures would be most beneficial in patients suffering the combination of neglect and hemianopia. Arm activation should be included in the rehabilitation programs of neglect; this is a useful technique for patients who need bedside treatment in the acute phase. With respect to the deficit in visual memory in association with neglect, the possible mechanisms of lateralized deficit in delayed recall need to be further examined and clarified. Intensive treatment induced recovery in both severe and moderate visual neglect long after the first two to first three months after the stroke.

Active sulphide mine tailings impoundments as sources of contaminated drainage: controlling factors, methods of characterisation and geochemical constraints for mitigation

Low quality mine drainage from tailings facilities persists as one of the most significant global environmental concerns related to sulphide mining. Due to the large variation in geological and environmental conditions at mine sites, universal approaches to the management of mine drainage are not always applicable. Instead, site-specific knowledge of the geochemical behaviour of waste materials is required for the design and closure of the facilities. In this thesis, tailings-derived water contamination and factors causing the pollution were investigated in two coeval active sulphide mine sites in Finland: the Hitura Ni mine and the Luikonlahti Cu-Zn-Co-Ni mine and talc processing plant. A hydrogeochemical study was performed to characterise the tailingsderived water pollution at Hitura. Geochemical changes in the Hitura tailings were evaluated with a detailed mineralogical and geochemical investigation (solid-phase speciation, acid mine drainage potential, pore water chemistry) and using a spatial assessment to identify the mechanisms of water contamination. A similar spatial investigation, applying selective extractions, was carried out in the Luikonlahti tailings area for comparative purposes (Hitura low-sulphide tailings vs. Luikonlahti sulphide-rich tailings). At both sites, hydrogeochemistry of tailings seepage waters was further characterised to examine the net results of the processes observed within the impoundments and to identify constraints for water treatment. At Luikonlahti, annual and seasonal variation in effluent quality was evaluated based on a four-year monitoring period. Observations pertinent to future assessment and mine drainage prevention from existing and future tailings facilities were presented based on the results. A combination of hydrogeochemical approaches provided a means to delineate the tailings-derived neutral mine drainage at Hitura. Tailings effluents with elevated Ni, SO₄ ^2- and Fe content had dispersed to the surrounding aquifer through a levelled-out esker and underneath the seepage collection ditches. In future mines, this could be avoided with additional basal liners in tailings impoundments where the permeability of the underlying Quaternary deposits is inadequate, and with sufficiently deep ditches. Based on the studies, extensive sulphide oxidation with subsequent metal release may already initiate during active tailings disposal. The intensity and onset of oxidation depended on e.g. the Fe sulphide content of the tailings, water saturation level, and time of exposure of fresh sulphide grains. Continuous disposal decreased sulphide weathering in the surface of low-sulphide tailings, but oxidation initiated if they were left uncovered after disposal ceased. In the sulphide-rich tailings, delayed burial of the unsaturated tailings had resulted in thick oxidized layers, despite the continuous operation. Sulphide weathering and contaminant release occurred also in the border zones. Based on the results, the prevention of sulphide oxidation should already be considered in the planning of tailings disposal, taking into account the border zones. Moreover, even lowsulphide tailings should be covered without delay after active disposal ceases. The quality of tailings effluents showed wide variation within a single impoundment and between the two different types of tailings facilities assessed. The affecting factors included source materials, the intensity of weathering of tailings and embankment materials along the seepage flow path, inputs from the process waters, the water retention time in tailings, and climatic seasonality. In addition, modifications to the tailings impoundment may markedly change the effluent quality. The wide variation in the tailings effluent quality poses challenges for treatment design. The final decision on water management requires quantification of the spatial and seasonal fluctuation at the site, taking into account changes resulting from the eventual closure of the impoundment. Overall, comprehensive hydrogeochemical mapping was deemed essential in the identification of critical contaminants and their sources at mine sites. Mineralogical analysis, selective extractions, and pore water analysis were a good combination of methods for studying the weathering of tailings and in evaluating metal mobility from the facilities. Selective extractions with visual observations and pH measurements of tailings solids were, nevertheless, adequate in describing the spatial distribution of sulphide oxidation in tailings impoundments. Seepage water chemistry provided additional data on geochemical processes in tailings and was necessary for defining constraints for water treatment.

Application of capillary electrophoretic methods for determining carbohydrates and aliphatic carboxylic acids formed during wood processing

Knowledge of the behaviour of cellulose, hemicelluloses, and lignin during wood and pulp processing is essential for understanding and controlling the processes. Determination of monosaccharide composition gives information about the structural polysaccharide composition of wood material and helps when determining the quality of fibrous products. In addition, monitoring of the acidic degradation products gives information of the extent of degradation of lignin and polysaccharides. This work describes two capillary electrophoretic methods developed for the analysis of monosaccharides and for the determination of aliphatic carboxylic acids from alkaline oxidation solutions of lignin and wood. Capillary electrophoresis (CE), in its many variants is an alternative separation technique to chromatographic methods. In capillary zone electrophoresis (CZE) the fused silica capillary is filled with an electrolyte solution. An applied voltage generates a field across the capillary. The movement of the ions under electric field is based on the charge and hydrodynamic radius of ions. Carbohydrates contain hydroxyl groups that are ionised only in strongly alkaline conditions. After ionisation, the structures are suitable for electrophoretic analysis and identification through either indirect UV detection or electrochemical detection. The current work presents a new capillary zone electrophoretic method, relying on in-capillary reaction and direct UV detection at the wavelength of 270 nm. The method has been used for the simultaneous separation of neutral carbohydrates, including mono- and disaccharides and sugar alcohols. The in-capillary reaction produces negatively charged and UV-absorbing compounds. The optimised method was applied to real samples. The methodology is fast since no other sample preparation, except dilution, is required. A new method for aliphatic carboxylic acids in highly alkaline process liquids was developed. The goal was to develop a method for the simultaneous analysis of the dicarboxylic acids, hydroxy acids and volatile acids that are oxidation and degradation products of lignin and wood polysaccharides. The CZE method was applied to three process cases. First, the fate of lignin under alkaline oxidation conditions was monitored by determining the level of carboxylic acids from process solutions. In the second application, the degradation of spruce wood using alkaline and catalysed alkaline oxidation were compared by determining carboxylic acids from the process solutions. In addition, the effectiveness of membrane filtration and preparative liquid chromatography in the enrichment of hydroxy acids from black liquor was evaluated, by analysing the effluents with capillary electrophoresis.

Neural mechanisms underlying conscious and unconscious vision. Evidence from event-related potentials and transcranial magnetic stimulation

Vision affords us with the ability to consciously see, and use this information in our behavior. While research has produced a detailed account of the function of the visual system, the neural processes that underlie conscious vision are still debated. One of the aims of the present thesis was to examine the time-course of the neuroelectrical processes that correlate with conscious vision. The second aim was to study the neural basis of unconscious vision, that is, situations where a stimulus that is not consciously perceived nevertheless influences behavior. According to current prevalent models of conscious vision, the activation of visual cortical areas is not, as such, sufficient for consciousness to emerge, although it might be sufficient for unconscious vision. Conscious vision is assumed to require reciprocal communication between cortical areas, but views differ substantially on the extent of this recurrent communication. Visual consciousness has been proposed to emerge from recurrent neural interactions within the visual system, while other models claim that more widespread cortical activation is needed for consciousness. Studies I-III compared models of conscious vision by studying event-related potentials (ERP). ERPs represent the brain’s average electrical response to stimulation. The results support the model that associates conscious vision with activity localized in the ventral visual cortex. The timing of this activity corresponds to an intermediate stage in visual processing. Earlier stages of visual processing may influence what becomes conscious, although these processes do not directly enable visual consciousness. Late processing stages, when more widespread cortical areas are activated, reflect the access to and manipulation of contents of consciousness. Studies IV and V concentrated on unconscious vision. By using transcranial magnetic stimulation (TMS) we show that when early visual cortical processing is disturbed so that subjects fail to consciously perceive visual stimuli, they may nevertheless guess (above chance-level) the location where the visual stimuli were presented. However, the results also suggest that in a similar situation, early visual cortex is necessary for both conscious and unconscious perception of chromatic information (i.e. color). Chromatic information that remains unconscious may influence behavioral responses when activity in visual cortex is not disturbed by TMS. Our results support the view that early stimulus-driven (feedforward) activation may be sufficient for unconscious processing. In conclusion, the results of this thesis support the view that conscious vision is enabled by a series of processing stages. The processes that most closely correlate with conscious vision take place in the ventral visual cortex ~200 ms after stimulus presentation, although preceding time-periods and contributions from other cortical areas such as the parietal cortex are also indispensable. Unconscious vision relies on intact early visual activation, although the location of visual stimulus may be unconsciously resolved even when activity in the early visual cortex is interfered with.

Lean daily management, visual management and continuous improvement

This thesis was part of lean adaptation project started at Outotec Lappeenranta factory in early 2013. The purpose of this thesis was to develop and propose lean tools that could be used in daily management, visual management and continuous improvement. This thesis was “outsiders” view, and as such, did not study the current processes deeply. As result of this thesis, two different Daily Management -boards were designed, one for parallel processes and one for sequential processes. In addition, methods of doing continuous improvement and daily task accountability were framed and standard work for the leaders outlined. The tools presented in this thesis are general tools which support work in lean environment. They are visual and, if used correctly, they provide a basis from which continuous improvement can be done. Lean philosophy emphasizes the deep understanding of the current situation and it would be against the lean principles to blindly implement anything developed “on the outside”. The tools presented should be reviewed and modified further by the people working on the factory floor.

Reframing the relationship between service design and operations: a service engineering approach

The significance of services as business and human activities has increased dramatically throughout the world in the last three decades. Becoming a more and more competitive and efficient service provider while still being able to provide unique value opportunities for customers requires new knowledge and ideas. Part of this knowledge is created and utilized in daily activities in every service organization, but not all of it, and therefore an emerging phenomenon in the service context is information awareness. Terms like big data and Internet of things are not only modern buzz-words but they are also describing urgent requirements for a new type of competences and solutions. When the amount of information increases and the systems processing information become more efficient and intelligent, it is the human understanding and objectives that may get separated from the automated processes and technological innovations. This is an important challenge and the core driver for this dissertation: What kind of information is created, possessed and utilized in the service context, and even more importantly, what information exists but is not acknowledged or used? In this dissertation the focus is on the relationship between service design and service operations. Reframing this relationship refers to viewing the service system from the architectural perspective. The selected perspective allows analysing the relationship between design activities and operational activities as an information system while maintaining the tight connection to existing service research contributions and approaches. This type of an innovative approach is supported by research methodology that relies on design science theory. The methodological process supports the construction of a new design artifact based on existing theoretical knowledge, creation of new innovations and testing the design artifact components in real service contexts. The relationship between design and operations is analysed in the health care and social care service systems. The existing contributions in service research tend to abstract services and service systems as value creation, working or interactive systems. This dissertation adds an important information processing system perspective to the research. The main contribution focuses on the following argument: Only part of the service information system is automated and computerized, whereas a significant part of information processing is embedded in human activities, communication and ad-hoc reactions. The results indicate that the relationship between service design and service operations is more complex and dynamic than the existing scientific and managerial models tend to view it. Both activities create, utilize, mix and share information, making service information management a necessary but relatively unknown managerial task. On the architectural level, service system -specific elements seem to disappear, but access to more general information elements and processes can be found. While this dissertation focuses on conceptual-level design artifact construction, the results provide also very practical implications for service providers. Personal, visual and hidden activities of service, and more importantly all changes that take place in any service system have also an information dimension. Making this information dimension visual and prioritizing the processed information based on service dimensions is likely to provide new opportunities to increase activities and provide a new type of service potential for customers.

International comparison of Russian food processing industry -Finnish perspective

Työn päätavoitteena on kartoittaa Venäjän elintarviketeollisuutta ulkomaisen investoijan näkökulmasta. Tutkimus arvioi liiketoimintamahdollisuuksia ja kilpailutilannetta Venäjän elintarviketeollisuudessa ja auttaa ulkomaisia yrityksiä toteuttamaan liiketoimintastrategioitaan Venäjällä. Venäjän ja muiden siirtymätalousmaiden markkinatilannevertailujen lisäksi Venäjän alueita verrataan keskenään. Myös mahdollisen WTO jäsenyyden vaikutuksia arvioidaan. Kommunismin perintö vaikuttaa edelleen Venäjän elintarviketeollisuuteen ja maatalouteen. Maatalouden tuottavuus on kaukana länsimaisesta tasosta ja maatiloilta puuttuu rahoitusta. Etenkin maidon- ja lihanjalostajat kärsivät raaka-ainepulasta. Venäjän kriisi vuonna 1998 vahvisti paikallista teollisuustuotantoa mutta aiheutti ongelmia ulkomaisille investoijille ja yrityksille, jotka vievät tuotteitaan Venäjälle. Edut, joita mahdollinen maailmankauppajärjestö WTO:n jäsenyys tuo, ovat merkittävämpiä Venäjälle kuin sen kauppakumppaneille. Venäjän alueet eivät ole yhtäläisesti kehittyneitä ja kuluttajien ostovoima vaihtelee paljon. Itsestään selvin ja houkuttelevin vaihtoehto menestyvien elintarvikeyritysten laajentumiselle löytyy alueilta, joilla ostovoima on suurin. Tähän asti kansainväliset elintarvikeyritykset ovat olleet enemmän kiinnostuneita Itä- ja Keski-Euroopan maista. Käytettävissä olevat tulot ovat Itä- ja Keski-Euroopan maissa suurempia kuin Venäjällä, joten tuottajat pystyvät myymään myös kalliimpia tuotteita. Työvoimakustannukset Venäjällä tulevat olemaan suotuisia vielä muutaman vuosikymmenen ja markkinoiden koko on merkittävä. Siksi kansainvälisillä elintarvikeyrityksillä riittää kiinnostusta tulevaisuudessa investoida myös Venäjälle.

On the innovation capacity of technologyrelated knowledge-intensive business services. A case study of the technology and engineering consulting (TEC) sector in Singapore

Even though the research on innovation in services has expanded remarkably especially during the past two decades, there is still a need to increase understanding on the special characteristics of service innovation. In addition to studying innovation in service companies and industries, research has also recently focused more on services in innovation, as especially the significance of so-called knowledge intensive business services (KIBS) for the competitive edge of their clients, othercompanies, regions and even nations has been proved in several previous studies. This study focuses on studying technology-based KIBS firms, and technology andengineering consulting (TEC) sector in particular. These firms have multiple roles in innovation systems, and thus, there is also a need for in-depth studies that increase knowledge about the types and dimensions of service innovations as well as underlying mechanisms and procedures which make the innovations successful. The main aim of this study is to generate new knowledge in the fragmented research field of service innovation management by recognizing the different typesof innovations in TEC services and some of the enablers of and barriers to innovation capacity in the field, especially from the knowledge management perspective. The study also aims to shed light on some of the existing routines and new constructions needed for enhancing service innovation and knowledge processing activities in KIBS companies of the TEC sector. The main samples of data in this research include literature reviews and public data sources, and a qualitative research approach with exploratory case studies conducted with the help of the interviews at technology consulting companies in Singapore in 2006. These complement the qualitative interview data gathered previously in Finland during a larger research project in the years 2004-2005. The data is also supplemented by a survey conducted in Singapore. The respondents for the survey by Tan (2007) were technology consulting companies who operate in the Singapore region. The purpose ofthe quantitative part of the study was to validate and further examine specificaspects such as the influence of knowledge management activities on innovativeness and different types of service innovations, in which the technology consultancies are involved. Singapore is known as a South-east Asian knowledge hub and is thus a significant research area where several multinational knowledge-intensive service firms operate. Typically, the service innovations identified in the studied TEC firms were formed by several dimensions of innovations. In addition to technological aspects, innovations were, for instance, related to new client interfaces and service delivery processes. The main enablers of and barriers to innovation seem to be partly similar in Singaporean firms as compared to the earlier study of Finnish TEC firms. Empirical studies also brought forth the significance of various sources of knowledge and knowledge processing activities as themain driving forces of service innovation in technology-related KIBS firms. A framework was also developed to study the effect of knowledge processing capabilities as well as some moderators on the innovativeness of TEC firms. Especially efficient knowledge acquisition and environmental dynamism seem to influence the innovativeness of TEC firms positively. The results of the study also contributeto the present service innovation literature by focusing more on 'innovation within KIBs' rather than 'innovation through KIBS', which has been the typical viewpoint stressed in the previous literature. Additionally, the study provides several possibilities for further research.

Numerical and ExperimentalModelling of Gas Flow and Heat Transfer in the Air Gap of An Electric Machine

This work deals with the cooling of high-speed electric machines, such as motors and generators, through an air gap. It consists of numerical and experimental modelling of gas flow and heat transfer in an annular channel. Velocity and temperature profiles are modelled in the air gap of a high-speed testmachine. Local and mean heat transfer coefficients and total friction coefficients are attained for a smooth rotor-stator combination at a large velocity range. The aim is to solve the heat transfer numerically and experimentally. The FINFLO software, developed at Helsinki University of Technology, has been used in the flow solution, and the commercial IGG and Field view programs for the grid generation and post processing. The annular channel is discretized as a sector mesh. Calculation is performed with constant mass flow rate on six rotational speeds. The effect of turbulence is calculated using three turbulence models. The friction coefficient and velocity factor are attained via total friction power. The first part of experimental section consists of finding the proper sensors and calibrating them in a straight pipe. After preliminary tests, a RdF-sensor is glued on the walls of stator and rotor surfaces. Telemetry is needed to be able to measure the heat transfer coefficients at the rotor. The mean heat transfer coefficients are measured in a test machine on four cooling air mass flow rates at a wide Couette Reynolds number range. The calculated values concerning the friction and heat transfer coefficients are compared with measured and semi-empirical data. Heat is transferred from the hotter stator and rotor surfaces to the coolerair flow in the air gap, not from the rotor to the stator via the air gap, althought the stator temperature is lower than the rotor temperature. The calculatedfriction coefficients fits well with the semi-empirical equations and precedingmeasurements. On constant mass flow rate the rotor heat transfer coefficient attains a saturation point at a higher rotational speed, while the heat transfer coefficient of the stator grows uniformly. The magnitudes of the heat transfer coefficients are almost constant with different turbulence models. The calibrationof sensors in a straight pipe is only an advisory step in the selection process. Telemetry is tested in the pipe conditions and compared to the same measurements with a plain sensor. The magnitudes of the measured data and the data from the semi-empirical equation are higher for the heat transfer coefficients than thenumerical data considered on the velocity range. Friction and heat transfer coefficients are presented in a large velocity range in the report. The goals are reached acceptably using numerical and experimental research. The next challenge is to achieve results for grooved stator-rotor combinations. The work contains also results for an air gap with a grooved stator with 36 slots. The velocity field by the numerical method does not match in every respect the estimated flow mode. The absence of secondary Taylor vortices is evident when using time averagednumerical simulation.