Fibre-reinforced composites as root canal posts

Fibre-reinforced composite (FRC) root canal posts are suggested to have biomechanical benefits over traditional metallic posts, but they lack good adhesion to resin composites. The aim of this series of studies was to evaluate the adhesion of individually formed fibre-reinforced composite material to composite resin and dentin, as well as some mechanical properties. Flexural properties were evaluated and compared between individually formed FRC post material and different prefabricated posts. The depth of polymerization of the individually formed FRC post material was evaluated with IR spectrophotometry and microhardness measurements, and compared to that of resin without fibres. Bonding properties of the individually formed FRC post to resin cements and dentin were tested using Pull-out- and Push-out-force tests, evaluated with scanning electron microscopy, and compared to those of prefabricated FRC and metal posts. Load-bearing capacity and microstrain were evaluated and failure mode assessment was made on incisors restored with individually formed FRC posts of different structures and prefabricated posts. The results of these studies show that the individually polymerized and formed FRC post material had higher flexural properties compared to the commercial prefabricated FRC posts. The individually polymerized FRC material showed almost the same degree of conversion after light polymerization as monomer resin without fibres. Moreover, it was found that the individually formed FRC post material with a semiinterpenetrating polymer network (IPN) polymer matrix bonded better to composite resin luting cement, than did the prefabricated posts with a cross-linked polymer matrix. Furthermore, it was found that, contrary to the other posts, there were no adhesive failures between the individually formed FRC posts and composite resin luting cement. This suggests better interfacial adhesion of cements to these posts. Although no differences in load-bearing capacity or microstrain could be seen, the incisors restored with individually formed FRC posts with a hollow structure showed more favourable failures compared to other prefabricated posts. These studies suggest that it is possible to use individually formed FRC material with semi-IPN polymer matrix as root canal post material. They also indicate that there are benefits especially regarding the bonding properties to composite resin and dentin with this material compared to prefabricated FRC post material with a cross-linked matrix. Furthermore, clinically more repairable failures were found with this material compared to those of prefabricated posts.

Fiber-reinforced Composite as Oral Implant Material. Experimental studies of glass fiber and bioactive glass in vitro and in vivo

Fiber-reinforced composite as oral implant material: Experimental studies of glass fiber and bioactive glass in vitro and in vivo Department of Prosthetic Dentistry and Biomaterials Science, Institute of Dentistry, University of Turku, Turku, Finland 2008. Biocompatibility and mechanical properties are important variables that need to be determined when new materials are considered for medical implants. Special emphasis was placed on these characteristics in the present work, which aimed to investigate the potential of fiber-reinforced composite (FRC) material as an oral implant. Furthermore, the purpose of this study was to explore the effect of bioactive glass (BAG) on osseointegration of FRC implants. The biocompatibility and mechanical properties of FRC implants were studied both in vitro and in vivo. The mechanical properties of the bulk FRC implant were tested with a cantilever bending test, torsional test and push-out test. The biocompatibility was first evaluated with osteoblast cells cultured on FRC substrates. Bone bonding was determined with the mechanical push-out test and histological as well as histomorplanimetric evaluation. Implant surface was characterized with SEM and EDS analysis. The results of these studies showed that FRC implants can withstand the static load values comparably to titanium. Threaded FRC implants had significantly higher push-out strength than the threaded titanium implants. Cell culture study revealed no cytotoxic effect of FRC materials on the osteoblast-like-cells. Addition of BAG particles enhanced cell proliferation and mineralization of the FRC substrates The in vivo study showed that FRC implants can withstand static loading until failure without fracture. The results also suggest that the FRC implant is biocompatible in bone. The biological behavior of FRC was comparable to that of titanium after 4 and 12 weeks of implantation. Furthermore, addition of BAG to FRC implant increases peri-implant osteogenesis and bone maturation.

Non-resorbable glass fibre-reinforced composite with porous surface as bone substitute material: Experimental studies in vitro and in vivo focused on bone-implant interface

The development of load-bearing osseous implant with desired mechanical and surface properties in order to promote incorporation with bone and to eliminate risk of bone resorption and implant failure is a very challenging task. Bone formation and resoption processes depend on the mechanical environment. Certain stress/strain conditions are required to promote new bone growth and to prevent bone mass loss. Conventional metallic implants with high stiffness carry most of the load and the surrounding bone becomes virtually unloaded and inactive. Fibre-reinforced composites offer an interesting alternative to metallic implants, because their mechanical properties can be tailored to be equal to those of bone, by the careful selection of matrix polymer, type of fibres, fibre volume fraction, orientation and length. Successful load transfer at bone-implant interface requires proper fixation between the bone and implant. One promising method to promote fixation is to prepare implants with porous surface. Bone ingrowth into porous surface structure stabilises the system and improves clinical success of the implant. The experimental part of this work was focused on polymethyl methacrylate (PMMA) -based composites with dense load-bearing core and porous surface. Three-dimensionally randomly orientated chopped glass fibres were used to reinforce the composite. A method to fabricate those composites was developed by a solvent treatment technique and some characterisations concerning the functionality of the surface structure were made in vitro and in vivo. Scanning electron microscope observations revealed that the pore size and interconnective porous architecture of the surface layer of the fibre-reinforced composite (FRC) could be optimal for bone ingrowth. Microhardness measurements showed that the solvent treatment did not have an effect on the mechanical properties of the load-bearing core. A push-out test, using dental stone as a bone model material, revealed that short glass fibre-reinforced porous surface layer is strong enough to carry load. Unreacted monomers can cause the chemical necrosis of the tissue, but the levels of leachable resisidual monomers were considerably lower than those found in chemically cured fibre-reinforced dentures and in modified acrylic bone cements. Animal experiments proved that surface porous FRC implant can enhance fixation between bone and FRC. New bone ingrowth into the pores was detected and strong interlocking between bone and the implant was achieved.

Development of porous glass-fiber reinforced composite for bone implants. Evaluation of antimicrobial effect and implant fixation

Cranial bone reconstructions are necessary for correcting large skull bone defects due to trauma, tumors, infections and craniotomies. Traditional synthetic implant materials include solid or mesh titanium, various plastics and ceramics. Recently, biostable glass-fiber reinforced composites (FRC), which are based on bifunctional methacrylate resin, were introduced as novel implant solution. FRCs were originally developed and clinically used in dental applications. As a result of further in vitro and in vivo testing, these composites were also approved for clinical use in cranial surgery. To date, reconstructions of large bone defects were performed in 35 patients. This thesis is dedicated to the development of a novel FRC-based implant for cranial reconstructions. The proposed multi-component implant consists of three main parts: (i) porous FRC structure; (ii) bioactive glass granules embedded between FRC layers and (iii) a silver-polysaccharide nanocomposite coating. The porosity of the FRC structure should allow bone ingrowth. Bioactive glass as an osteopromotive material is expected to stimulate the formation of new bone. The polysaccharide coating is expected to prevent bacterial colonization of the implant. The FRC implants developed in this study are based on the porous network of randomly-oriented E-glass fibers bound together by non-resorbable photopolymerizable methacrylate resin. These structures had a total porosity of 10–70 volume %, of which > 70% were open pores. The pore sizes > 100 μm were in the biologically-relevant range (50-400 μm), which is essential for vascularization and bone ingrowth. Bone ingrowth into these structures was simulated by imbedding of porous FRC specimens in gypsum. Results of push-out tests indicated the increase in the shear strength and fracture toughness of the interface with the increase in the total porosity of FRC specimens. The osteopromotive effect of bioactive glass is based on its dissolution in the physiological environment. Here, calcium and phosphate ions, released from the glass, precipitated on the glass surface and its proximity (the FRC) and formed bone-like apatite. The biomineralization of the FRC structure, due to the bioactive glass reactions, was studied in Simulated Body Fluid (SBF) in static and dynamic conditions. An antimicrobial, non-cytotoxic polysaccharide coating, containing silver nanoparticles, was obtained through strong electrostatic interactions with the surface of FRC. In in vitro conditions the lactose-modified chitosan (chitlac) coating showed no signs of degradation within seven days of exposure to lysozyme or one day to hydrogen peroxide (H2O2). The antimicrobial efficacy of the coating was tested against Staphylococcus aureus and Pseudomonas aeruginosa. The contact-active coating had an excellent short time antimicrobial effect. The coating neither affected the initial adhesion of microorganisms to the implant surface nor the biofilm formation after 24 h and 72 h of incubation. Silver ions released to the aqueous environment led to a reduction of bacterial growth in the culture medium.

Offering planning with support of roadmapping in project business

Tämän tutkielman tavoitteena on tutkia kuinka roadmapping-tekniikkaa voidaan käyttää tarjonnan suunnittelun tukena uusien tuotteiden valmistamisen yhteydessä. Työ koostuu teoreettisesta ja käytännönläheisestä osasta. Teoreettinen runko on luotu selventämään kuinka tämän hetkisen tutkimus- ja kehitys projektit lopulta muodostavat tulevaisuuden tarjoaman. Menestyksekkään tuotetarjoaman luominen vaatii, sekä uusien teknologioiden kehittämistä, että markkinoilla olevien asiakkaiden tarpeiden ymmärtämistä. Asiakassuuntaisten tuotteiden kehittäminen vaatii toimintaympäristöstä ja asiakasrajapinnasta tulevien signaalien tunnistamista ja niiden ohjaamista tuote- ja teknologia platformeille. Strategia luodaan tukemaan päätöksentekoa prosessin eri vaiheissa. Yrityskohtainen osio koostuu analyysistä, joka on tehty teetetyn kyselyn ja haas-tattelujen pohjalta. Osana analyysia ovat Major project-yksikön tämänhetkinen tarjonnansuunnitteluprosessi, strategian soveltaminen, informaation kerääminen ja priorisointi, portfolionhallinta ja roadmap-tekniikan käyttö. Ratkaisussa on esitet-ty tarjonnan suunnitteluprosessi ja siihen liittyvät kriittiset komponentit. Roadmapping-tekniikkaaon luotu yhdistämään toimintaympäristö, tuotteet ja teknologia toisiinsa. Toimintaympäristö ja tuotteet on yhdistetty myös linked-grids-tekniikan avulla.

Tuotannon kehittäminen aihiotehtaassa

Työn tavoitteena oli kuvata Artowood Oy:ssä toteutettu tuotannon kehittämishanke sekä arvioida sen nykyistä tuotantoa. Lisäksi käsiteltiin yrityksen asemaa alihankintayrityksenä. Teoriaosuudessa verrattiin eri tuotannonohjausteorioita, käsiteltiin tuotannon ajoitukseen liittyviä kysymyksiä sekä paneuduttiin tuotannon kehittämiseen ja laatuun. Johtopäätöksenä, kehitetty tuotannonohjausjärjestelmä on toimiva nykyisissä olosuhteissa, mutta yrityksen kasvaessaon kiinnitettävä enemmän huomiota tuotannon ajoitusongelmien hallintaan. Lisäksi tuotannon laatua on joka tapauksessa kehitettävä. Artowood Oy on käynnistänyt toimenpiteet oman suoran viennin aloittamiseksi, sillä kotimaan markkinat ovat epävakaat kausivaihteluiden ja kiristyneen kilpailun seurauksena. Vientiprojektinonnistuminen on tärkeää, sillä kotimaassa on liian vähän sellaisia asiakkaita, joilla on tarve Artowood Oy:n tuotantoteknologian kannalta riittävän suurille valmistuserille.

Mapping out customer segments and marketing channels in the Finnish Homelift market

Työn tavoitteena oli saada selville ketkä ovat uuden tuotteen, eli kotihissin asiakkaat. Mitkä ovat tuotteen mahdollisuudet Suomen markkinoilla ja onko markkinoilla odotettavissa kasvua, sekä miten tähän mahdolliseen kasvuun päästäisiin käsiksi. Kotihissin ominaisuudet vaikuttavat siihen, että se on tarkoitettu asennettavaksi yksityisiin pientaloihin. Uuden tuotteen ansiosta KONE voi liittää nykyiseen vahvaan toimialaansa, eli kerrostaloihin, uuden aluevaltauksen; Pientalot. Tämä 'laajentuminen' tuo mukanaan kuluttajamarkkinoiden haasteet. Markkinatilanteen selvittämiseen käyttin jo olemassa olevaa tietoa hyväkseni; sanomalehdistä markkinatutkimuksiin. Asiakasryhmät kartoitin tutustumalla messutapahtumissa saatuihin kontakteihin. Päätutkimusmenetelmänä käytin haastatteluja. Niihin osallistui kaikkiaan 14 vastaajaa. He vasatsivat kysymyksiin ostomotiiveista ja tuotteesta. Eräs haastattelujen tärkeimmistä teemoista liittyi yhteydenpito- ja jakelukanaviin, joista 12 vastaajaa antoivat mielipiteitään. Työni tulokset viittaavat siihen, että markkinatilanne näyttää positiiviselta KONEen kannalta. Tutkimuksesta sain selville kotihissin asiakassegmentit ja myös miten nämä potentiaaliset asiakkaat saadaan tehokkaimmin tavoitettua.

The design and implementation of a standards-based mobile messaging platform - case WAP Push Proxy Gateway

Tässä diplomityössä perehdytään WAP:in Push -viitekehykseen. WAP-standardit määrittelevät kuinka Internet-tyyppisiä palveluita, joita voidaan käyttää erilaisia mobiileja päätelaiteitteita käyttäen, toteutetaan tehokkaalla ja verkkoteknologiasta riippumattomalla tavalla. WAP pohjautuu Internet:iin, mutta huomioi pienten päätelaitteiden ja mobiiliverkkojen rajoitukset ja erikoisominaisuudet. WAP Push viitekehys määrittelee verkon aloittaman palvelusisällön toimittamisen. Työn teoriaosassa käydään läpi yleinen WAP-arkkitehtuuri ja WAP-protokollapino käyttäen vertailukohtina lanka-Internetin arkkitehtuuria ja protokollapinoa. Edellistä perustana käyttäen tutustaan WAP Push -viitekehykseen. Käytännönosassa kuvataan WAP Push -välityspalvelimen suunnittelu ja kehitystyö. WAP Push -välityspalvelin on keskeinen verkkoelementti WAP Push -viitekehyksessä. WAP Push -välityspalvelin yhdistää Internetin ja mobiiliverkon tavalla, joka piilottaa teknologiaeroavaisuudet Internetissä olevalta palveluntuottajalta.

Product Launch in Industrial Markets – Financial Risks in New AMD Elevator Door Launch

Tuotekehitys ja uusien tuotteiden lanseeraus on teollisen yrityksen menestyksekkään liiketoiminnan elinehtoja tämän päivän kilpailussa. Teollisuusyrityksen tuotteiden innovaatioaikakausia on ollut lukuisia, samoin kuin uuden tuotteen lanseerauksen lähtökohtia. Aikakausista, jolloin tuotteita kehitettiin yrityksen omista lähtökohdista, kuten valmistuksellisista eduista, on edetty tilanteeseen, jossa markkinoiden tarpeita tulee ottaa yhä enemmän huomioon. Kuitenkin, teollisuudessa esitellään tuotteita yhä puhtaasti tuotantolähtöisesti, ja tutkimuksen tavoitteena on selvittää taloudellisia riskejä, joita liittyy puhtaasti teknologiavetoiseen tuotteiden kehitystyöhön, valmistukseen ja lanseeraukseen. Normatiivisena tutkimuksena työ pyrkii asiakastarpeita ja teollisuusyrityksen loppuasiakkaiden näkökulmia huomioon ottaen osoittamaan markkinoinnin keinojen merkityksen tuotantolähtöisen tuotelanseerauksen taloudellisten riskien minimoimiseksi. Uuden teollisen tuotteen asiakastarpeita on selvitetty kyselymuotoisen markkinointitutkimuksen menetelmiä hyväksikäyttäen. Tuotteen tärkeimpien ominaisuuksien, kuten turvallisuuden, kestävyyden ja hinnan merkitystä voidaan hyödyntää ennen tuotteen kaupallista esittelyä potentiaalisten asiakassegmenttien kartoitukseen ja menestyksellisen lanseerauksen edesauttamiseksi.

Validation of plant dynamic model by online and laboratory measurements – a tool to predict online COD loads out of production of mechanical printing papers

COD discharges out of processes have increased in line with elevating brightness demands for mechanical pulp and papers. The share of lignin-like substances in COD discharges is on average 75%. In this thesis, a plant dynamic model was created and validated as a means to predict COD loading and discharges out of a mill. The assays were carried out in one paper mill integrate producing mechanical printing papers. The objective in the modeling of plant dynamics was to predict day averages of COD load and discharges out of mills. This means that online data, like 1) the level of large storage towers of pulp and white water 2) pulp dosages, 3) production rates and 4) internal white water flows and discharges were used to create transients into the balances of solids and white water, referred to as “plant dynamics”. A conversion coefficient was verified between TOC and COD. The conversion coefficient was used for predicting the flows from TOC to COD to the waste water treatment plant. The COD load was modeled with similar uncertainty as in reference TOC sampling. The water balance of waste water treatment was validated by the reference concentration of COD. The difference of COD predictions against references was within the same deviation of TOC-predictions. The modeled yield losses and retention values of TOC in pulping and bleaching processes and the modeled fixing of colloidal TOC to solids between the pulping plant and the aeration basin in the waste water treatment plant were similar to references presented in literature. The valid water balances of the waste water treatment plant and the reduction model of lignin-like substances produced a valid prediction of COD discharges out of the mill. A 30% increase in the release of lignin-like substances in the form of production problems was observed in pulping and bleaching processes. The same increase was observed in COD discharges out of waste water treatment. In the prediction of annual COD discharge, it was noticed that the reduction of lignin has a wide deviation from year to year and from one mill to another. This made it difficult to compare the parameters of COD discharges validated in plant dynamic simulation with another mill producing mechanical printing papers. However, a trend of moving from unbleached towards high-brightness TMP in COD discharges was valid.

Novel Robot Solutions for Carrying out Field Joint Welding and Machining in the Assembly of the Vacuum Vessel of ITER

It is necessary to use highly specialized robots in ITER (International Thermonuclear Experimental Reactor) both in the manufacturing and maintenance of the reactor due to a demanding environment. The sectors of the ITER vacuum vessel (VV) require more stringent tolerances than normally expected for the size of the structure involved. VV consists of nine sectors that are to be welded together. The vacuum vessel has a toroidal chamber structure. The task of the designed robot is to carry the welding apparatus along a path with a stringent tolerance during the assembly operation. In addition to the initial vacuum vessel assembly, after a limited running period, sectors need to be replaced for repair. Mechanisms with closed-loop kinematic chains are used in the design of robots in this work. One version is a purely parallel manipulator and another is a hybrid manipulator where the parallel and serial structures are combined. Traditional industrial robots that generally have the links actuated in series are inherently not very rigid and have poor dynamic performance in high speed and high dynamic loading conditions. Compared with open chain manipulators, parallel manipulators have high stiffness, high accuracy and a high force/torque capacity in a reduced workspace. Parallel manipulators have a mechanical architecture where all of the links are connected to the base and to the end-effector of the robot. The purpose of this thesis is to develop special parallel robots for the assembly, machining and repairing of the VV of the ITER. The process of the assembly and machining of the vacuum vessel needs a special robot. By studying the structure of the vacuum vessel, two novel parallel robots were designed and built; they have six and ten degrees of freedom driven by hydraulic cylinders and electrical servo motors. Kinematic models for the proposed robots were defined and two prototypes built. Experiments for machine cutting and laser welding with the 6-DOF robot were carried out. It was demonstrated that the parallel robots are capable of holding all necessary machining tools and welding end-effectors in all positions accurately and stably inside the vacuum vessel sector. The kinematic models appeared to be complex especially in the case of the 10-DOF robot because of its redundant structure. Multibody dynamics simulations were carried out, ensuring sufficient stiffness during the robot motion. The entire design and testing processes of the robots appeared to be complex tasks due to the high specialization of the manufacturing technology needed in the ITER reactor, while the results demonstrate the applicability of the proposed solutions quite well. The results offer not only devices but also a methodology for the assembly and repair of ITER by means of parallel robots.

Development of research networks : the case of social capital

The aim of this study is to explore how a new concept appears inscientific discussion and research, how it diffuses to other fields and out of the scientific communities, and how the networks are formed around the concept. Text and terminology take the interest of a reader in the digital environment. Texts create networks where the terminology used is dependent on the ideas, viewsand paradigms of the field. This study is based mainly on bibliographic data. Materials for bibliometric studies have been collected from different databases. The databases are also evaluated and their quality and coverage are discussed. The thesauri of those databases that have been selected for a more in depth study have also been evaluated. The material selected has been used to study how long and in which ways an innovative publication, which can be seen as a milestone in a specific field, influences the research. The concept that has been chosen as a topic for this research is Social Capital, because it has been a popular concept in different scientific fields as well as in everyday speech and the media. It seemed to be a `fashion concept´ that appeared in different situations at the Millennium. The growth and diffusion of social capital publications has been studied. The terms connected with social capital in different fields and different stages of the development have also been analyzed. The methods that have been used in this study are growth and diffusion analysis, content analysis, citation analysis, coword analysis and cocitation analysis. One method that can be used tounderstand and to interpret results of these bibliometric studies is to interview some key persons, who are known to have a gatekeeper position in the diffusion of the concept. Thematic interviews with some Finnish researchers and specialists that have influenced the diffusion of social capital into Finnish scientificand social discussions provide background information. iv The Milestone Publications on social capital have been chosen and studied. They give answers to the question "What is Social Capital?" By comparing citations to Milestone Publications with the growth of all social capital publications in a database, we can drawconclusions about the point at which social capital became generally approved `tacit knowledge´. The contribution of the present study lies foremost in understanding the development of network structures around a new concept that has diffused in scientific communities and also outside them. The network means both networks of researchers, networks of publications and networks of concepts that describe the research field. The emphasis has been on the digital environment and onthe socalled information society that we are now living in, but in this transitional stage, the printed publications are still important and widely used in social sciences and humanities. The network formation is affected by social relations and informal contacts that push new ideas. This study also gives new information about using different research methods, like bibliometric methods supported by interviews and content analyses. It is evident that interpretation of bibliometric maps presupposes qualitative information and understanding of the phenomena under study.

The Usage of Microsoft Push Notification Service on Mobile Devices

Along with the increasing in demand of mobile computing, Push Notification (PN) is widely used in mobile phones and other devices. PN allows the developer to send messages to the end users even when the client application is not running at the moment. This solves the problem produced by non-supported multi-tasking feature as well as saving battery life. Microsoft Push Notification Service (MPNS) is one solution to use PNs in Windows Phones. The thesis gives the developers an idea of how to use PNs by introducing MPNS, comparing MPNS with other Push Notification Services, usage of different PN types analysis, and PN simulation system implementation.

Peter Pan never goes out of style : nuorisotutkijat ymmällään

Kirjallisuusarvostelu