Active sulphide mine tailings impoundments as sources of contaminated drainage: controlling factors, methods of characterisation and geochemical constraints for mitigation

Low quality mine drainage from tailings facilities persists as one of the most significant global environmental concerns related to sulphide mining. Due to the large variation in geological and environmental conditions at mine sites, universal approaches to the management of mine drainage are not always applicable. Instead, site-specific knowledge of the geochemical behaviour of waste materials is required for the design and closure of the facilities. In this thesis, tailings-derived water contamination and factors causing the pollution were investigated in two coeval active sulphide mine sites in Finland: the Hitura Ni mine and the Luikonlahti Cu-Zn-Co-Ni mine and talc processing plant. A hydrogeochemical study was performed to characterise the tailingsderived water pollution at Hitura. Geochemical changes in the Hitura tailings were evaluated with a detailed mineralogical and geochemical investigation (solid-phase speciation, acid mine drainage potential, pore water chemistry) and using a spatial assessment to identify the mechanisms of water contamination. A similar spatial investigation, applying selective extractions, was carried out in the Luikonlahti tailings area for comparative purposes (Hitura low-sulphide tailings vs. Luikonlahti sulphide-rich tailings). At both sites, hydrogeochemistry of tailings seepage waters was further characterised to examine the net results of the processes observed within the impoundments and to identify constraints for water treatment. At Luikonlahti, annual and seasonal variation in effluent quality was evaluated based on a four-year monitoring period. Observations pertinent to future assessment and mine drainage prevention from existing and future tailings facilities were presented based on the results. A combination of hydrogeochemical approaches provided a means to delineate the tailings-derived neutral mine drainage at Hitura. Tailings effluents with elevated Ni, SO₄ ^2- and Fe content had dispersed to the surrounding aquifer through a levelled-out esker and underneath the seepage collection ditches. In future mines, this could be avoided with additional basal liners in tailings impoundments where the permeability of the underlying Quaternary deposits is inadequate, and with sufficiently deep ditches. Based on the studies, extensive sulphide oxidation with subsequent metal release may already initiate during active tailings disposal. The intensity and onset of oxidation depended on e.g. the Fe sulphide content of the tailings, water saturation level, and time of exposure of fresh sulphide grains. Continuous disposal decreased sulphide weathering in the surface of low-sulphide tailings, but oxidation initiated if they were left uncovered after disposal ceased. In the sulphide-rich tailings, delayed burial of the unsaturated tailings had resulted in thick oxidized layers, despite the continuous operation. Sulphide weathering and contaminant release occurred also in the border zones. Based on the results, the prevention of sulphide oxidation should already be considered in the planning of tailings disposal, taking into account the border zones. Moreover, even lowsulphide tailings should be covered without delay after active disposal ceases. The quality of tailings effluents showed wide variation within a single impoundment and between the two different types of tailings facilities assessed. The affecting factors included source materials, the intensity of weathering of tailings and embankment materials along the seepage flow path, inputs from the process waters, the water retention time in tailings, and climatic seasonality. In addition, modifications to the tailings impoundment may markedly change the effluent quality. The wide variation in the tailings effluent quality poses challenges for treatment design. The final decision on water management requires quantification of the spatial and seasonal fluctuation at the site, taking into account changes resulting from the eventual closure of the impoundment. Overall, comprehensive hydrogeochemical mapping was deemed essential in the identification of critical contaminants and their sources at mine sites. Mineralogical analysis, selective extractions, and pore water analysis were a good combination of methods for studying the weathering of tailings and in evaluating metal mobility from the facilities. Selective extractions with visual observations and pH measurements of tailings solids were, nevertheless, adequate in describing the spatial distribution of sulphide oxidation in tailings impoundments. Seepage water chemistry provided additional data on geochemical processes in tailings and was necessary for defining constraints for water treatment.

Selective leaching of multimetal tailings

Depletion of high grade mineral resources, tightening of environmental regulations and the environmental impact of acid mine drainage caused by sulfidic minerals continuously increase the interest in processing tailings and other mine waste. Treating waste requires additional capital and operational input, but the decrease in size and need of tailings ponds and permits decrease the overall costs. Treatment and utilization of the tailings could also bring added revenue by the recovery of valuables. Leaching of metal sulfides is very demanding and time consuming and hence process conditions need to be carefully optimized. The leaching of sulfides is affected by for example the choice of leaching agent, its concentration and temperature, pH, the redox potential, pressure, pulp density and particle size distribution. With reference to the mine case study the leaching of nickel and copper sulfides, especially the primary minerals pentlandite and chalcopyrite were investigated. Leaching behavior and recoveries for nickel, copper and iron were found out by sulfuric and citric acid leaching experiments using tailings samples of high and low sulfur content. Moderate recoveries were obtained and citric acid seemed more attractive. Increase in temperature and decrease in pulp density had positive effect on the recovery and pH was also proven to have a significant effect on the recovery of valuables. The rate determining step was determined through kinetic modeling in case of all valuables separately. Leaching was controlled by diffusion. The investigated multimetal tailing showed moderate potential in recovering of metal valuables from low grade tailing deposits. The process conditions should however be further optimized.

Past, present and future - assessing changes in aquatic environments using subfossil diatoms

The deterioration of surface waters is one of the most important issues in the environmental management of the European Union. Thus, the EU Water Framework Directive 2000/60/EC (WFD) requires “good ecological and chemical status” of surface waters by 2015 allowing only a slight departure from ecological reference conditions characterized by the biological communities typical for the conditions of minimal anthropogenic impact. The WFD requires the determination of ecological reference conditions and the present ecological status of surface waters. To meet this legislative demand, sedimentary diatom assemblages were used in these studies with various methods 1) to assess natural and human activity induced environmental changes, 2) to characterize background conditions 3) to evaluate the present ecological status and 4) to predict the future of the water bodies in the light of palaeolimnological data. As the WFD refers to all surface waters, both coastal and inland sites were included. Two long and two short sediment cores from the Archipelago Sea in the northern Baltic Sea were examined for their siliceous microfossils in order to assess (1) the Holocene palaeoenvironmental history and (2) the recent eutrophication of the area. The diatom record was divided into local diatom assemblage zones (LDAZ, long cores) and diatom assemblage zones (DAZ, short cores). Locally weighted weighted averaging regression and calibration (LWWA) was applied for the quantitative reconstruction of past TN concentrations (short cores). An age model for the long cores was constructed by using independent palaeomagnetic and AMS-14C methods. The short cores were dated using radiometric (210Pb, 226Ra and 137Cs) methods. The long cores date back to the early history of the Archipelago Sea, which was freshwater – no salinity increase referable to the brackish phase of the Yoldia Sea is recognized. The nutrient status of the lacustrine phase was slightly higher in the Archipelago Sea than in the Baltic Proper. Initial brackish-water influence is observed at 8 150 ±80 cal. BP (LDAZ4), but fully brackish conditions were established at 7 700 ±80 cal. BP (LDAZ5). The diatom assemblages indicate increasing salinity, warming climate and possible eutrophic conditions during the lacustrine to brackish-water transition. The decreasing abundance of Pseudosolenia calcar-avis (Schultze) Sundström and the increasing abundance of the ice-cover indicator species Pauliella taeniata (Grunow) Round and Basson indicate decreasing salinity and climatic cooling after ca. 5 000 cal. BP. Signs of eutrophication are visible in the most recent diatom assemblage zones of both short cores. Diatom-inferred total nitrogen (DI-TN) reconstructions partially fail to trace the actual measured total nitrogen concentrations especially from the late 1980s to the mid 1990s. This is most likely due to the dominating diatom species Pauliella taeniata, Thalassiosira levanderi Van Goor and Fragilariopsis cylindrus (Grunow) W. Krieger being more influenced by factors such as the length of the ice-season rather than nutrient concentrations. It is concluded that the diatom assemblages of the study sites are principally governed by climate fluctuations, with a slight influence of eutrophication visible in the most recent sediments. There are indications that global warming, with reduced ice cover, could impact the spring blooming diatom species composition in the Archipelago Sea. In addition, increased sediment accumulation in the early 90s coincides with the short ice-seasons suggesting that warming climate with decreasing ice-cover may increase sedimentation in the study area. The diverse diatom assemblages dominated by benthic species (54 %) in DAZ1 in the Käldö Fjärd core can be taken as background diatom assemblages for the Archipelago Sea. Since then turbidity has increased and the diatom assemblages have been dominated by planktonic diatoms from around the mid 1800s onwards. The reconstructed reference conditions for the total nitrogen concentrations fluctuate around 400 μg l-1. Altogether two short sediment cores and eight short cores for top-bottom analysis were retrieved from Lake Orijärvi and Lake Määrjärvi to assess the impact of the acid mine drainage (AMD) derived metals from the Orijärvi mine tailings on the diatom communities of the lakes. The Cu (Pb, Zn) mine of Orijärvi (1757 – 1956) was the first one in Finland where flotation techniques (1911 – 1955) were used to enrich ore and large quantities of tailings were produced. The AMD derived metal impact to the lakes was found to be among the heaviest thus far recorded in Finland. Concentrations of Cu, Pb and Zn in Lake Orijärvi sediments are two to three orders of magnitude higher than background values. The metal inputs have affected Lake Orijärvi and Lake Määrjärvi diatom communities at the community levels through shifts in dominant taxa (both lakes) and at the individual level through alteration in frustule morphology (Lake Orijärvi). At present, lake water still has elevated heavy metal levels, indicating that the impact from the tailings area continues to affect both lakes. Lake Orijärvi diatom assemblages are completely dominated by benthic species and are lacking planktonic diatoms. In Lake Määrjärvi the proportion of benthic and tychoplanktonic diatoms has increased and the planktonic taxa have decreased in abundance. Achnanthidium minutissimum Kützing and Brachysira vitrea (Grun.) R. Ross in Hartley were the most tolerant species to increased metal concentrations. Planktonic diatoms are more sensitive to metal contamination than benthic taxa, especially species in the genus Cyclotella (Kützing) Brébisson. The ecological reference conditions assessed in this study for Lake Orijärvi and Lake Määrjärvi comprise diverse planktonic and benthic communitites typical of circumneutral oligotrophic lakes, where the planktonic diatoms belonging to genera Cyclotella , Aulacoseira Thwaites, Tabellaria Ehrenberg and Asterionella Hassall dominate in relative abundances up to ca. 70%. The benthic communities are more diverse than the planktonic consisting of diatoms belonging to the genera Achnanthes Bory, Fragilaria Lyngbye and Navicula St. Vincent. This study clearly demonstrates that palaeolimnological methods, especially diatom analysis, provide a powerful tool for the EU Water Frame Work Directive for defining reference conditions, natural variability and current status of surface waters. The top/bottom approach is a very useful tool in larger-scale studies needed for management purposes. This “before and after” type of sediment sampling method can provide a very time and cost effective assessment of ecological reference conditions of surface waters.

Mining in Developing Countries: A Case Study of Sustainability Challenges

Mining has severe impacts on its surrounding. Particularly in the developing countries it has degraded the environment and signigicantly altered the socio-economical dynamics of the hosts. Especially relocation disrupts people from their homes, livelihoods, cultures and social activities. Mining industry has failed to develop the local host and streghten its governance structures; instead it has further degraded the development of mineral rich third world countries, which are among the world poorest ones. Cash flows derived from mining companies have not benefitted the crass-root level that however, bears most of the detrimental impacts. Especially if the governance structure of the host is weak, the sudden wealth is likely to accelerate disparities, corruption and even fuel wars. Environmental degradation, miscommunication, mistrust and disputes over land use have created conflicts between the communities and a mining company in Obuasi, Ghana; a case study of this thesis. The disputes are deeply rooted and further fuelled by unrealistic expectations and broken promises. The relations with artisanal and illegal miners have been especially troublesome. Illegal activities, mainly encroachment of the land and assets of the mine, such as vandalising tailings pipes have resulted in profits losses, environmental degradation and security hazards. All challenges mentioned above have to be addressed locally with site-specific solutions. It is vital to increase two-way communication, initiate collaboration and build capacity of the stakeholders such as local communities, NGOs and governance authorities. The locals must be engaged to create livelihood opportunities that are designed with and for them. Capacity can also be strengthened through education and skills training, such as women’s literacy programs. In order to diminish the overdependence of locals to the mine, the activities have to be self -sufficient and able to survive without external financial and managerial inputs. Additionally adequate and fair compensation practises and dispute resolution methods that are understood and accepted by all parties have to be agreed on as early as possible.

Recovery and refining of manganese as by-product from hydrometallurgical processes

The consumption of manganese is increasing, but huge amounts of manganese still end up in waste in hydrometallurgical processes. The recovery of manganese from multi-metal solutions at low concentrations may not be economical. In addition, poor iron control typically prevents the production of high purity manganese. Separation of iron from manganese can be done with chemical precipitation or solvent extraction methods. Combined carbonate precipitation with air oxidation is a feasible method to separate iron and manganese due to the fast kinetics, good controllability and economical reagents. In addition the leaching of manganese carbonate is easier and less acid consuming than that of hydroxide or sulfide precipitates. Selective iron removal with great efficiency from MnSO4 solution is achieved by combined oxygen or air oxidation and CaCO3 precipitation at pH > 5.8 and at a redox potential of > 200 mV. In order to avoid gypsum formation, soda ash should be used instead of limestone. In such case, however, extra attention needs to be paid on the reagents mole ratios in order to avoid manganese coprecipitation. After iron removal, pure MnSO4 solution was obtained by solvent extraction using organophosphorus reagents, di-(2-ethylhexyl)phosphoric acid (D2EHPA) and bis(2,4,4- trimethylpentyl)phosphinic acid (CYANEX 272). The Mn/Ca and Mn/Mg selectivities can be increased by decreasing the temperature from the commonly used temperatures (40 –60oC) to 5oC. The extraction order of D2EHPA (Ca before Mn) at low temperature remains unchanged but the lowering of temperature causes an increase in viscosity and slower phase separation. Of these regents, CYANEX 272 is selective for Mn over Ca and, therefore, it would be the better choice if there is Ca present in solution. A three-stage Mn extraction followed by a two-stage scrubbing and two-stage sulfuric acid stripping is an effective method of producing a very pure MnSO4 intermediate solution for further processing. From the intermediate MnSO4 some special Mn- products for ion exchange applications were synthesized and studied. Three types of octahedrally coordinated manganese oxide materials as an alternative final product for manganese were chosen for synthesis: layer structured Nabirnessite, tunnel structured Mg-todorokite and K-kryptomelane. As an alternative source of pure MnSO4 intermediate, kryptomelane was synthesized by using a synthetic hydrometallurgical tailings. The results show that the studied OMS materials adsorb selectively Cu, Ni, Cd and K in the presence of Ca and Mg. It was also found that the exchange rates were reasonably high due to the small particle dimensions. Materials are stable in the studied conditions and their maximum Cu uptake capacity was 1.3 mmol/g. Competitive uptake of metals and acid was studied using equilibrium, batch kinetic and fixed-bed measurements. The experimental data was correlated with a dynamic model, which also accounts for the dissolution of the framework manganese. Manganese oxide micro-crystals were also bound onto silica to prepare a composite material having a particle size large enough to be used in column separation experiments. The MnOx/SiO2 ratio was found to affect significantly the properties of the composite. The higher the ratio, the lower is the specific surface area, the pore volume and the pore size. On the other hand, higher amount of silica binder gives composites better mechanical properties. Birnesite and todorokite can be aggregated successfully with colloidal silica at pH 4 and with MnO2/SiO2 weight ratio of 0.7. The best gelation and drying temperature was 110oC and sufficiently strong composites were obtained by additional heat-treatment at 250oC for 2 h. The results show that silica–supported MnO2 materials can be utilized to separate copper from nickel and cadmium. The behavior of the composites can be explained reasonably well with the presented model and the parameters estimated from the data of the unsupported oxides. The metal uptake capacities of the prepared materials were quite small. For example, the final copper loading was 0.14 mmol/gMnO2. According to the results the special MnO2 materials are potential for a specific environmental application to uptake harmful metal ions.

Kompostipiireissä opittua : Eloperäiset jätteet kiertoon -hanke

Kompostien käyttöä on kokeiltu ja tutkittu Kainuun ELY-keskuksen Eloperäiset jätteet kiertoon -hankkeessa. Komposteja on hyödynnetty laskettelurinteen ja kaivosteollisuuden sivukiven läjitysalueen maisemoinnissa, pihanurmen ja energiakasvien kasvattamisessa, metsän lannoittamisessa ja maanviljelyssä. Pihanurmen perustamisen ja energiakasvien kasvattamisen kokeiluista on tehty myös erilliset tutkimukset. Tutkimustyöstä on vastannut MTT (Maa- ja elintarviketalouden tutkimuskeskus). Tutkimustieto on sisällytetty tähän julkaisuun. Kompostin käyttökokeissa ja tutkimuksissa on hyödynnetty Kainuun kuntien ja Kainuun jätehuollon kuntayhtymän Eko-Kympin komposteja. Kaikki kompostit ovat aumakompostoinnin tuotoksia. Eko-Kympin komposti on valmistettu biojätteistä. Muut kompostit ovat lähtöisin kunnallisten jätevedenpuhdistamoiden lietteistä. Kajaanin kompostia kutsutaan myös A. & E. Juntunen Oy:n valmistamaksi biomullaksi. Saatujen kokemusten ja tutkimusten mukaan aumakompostoinnilla tuotettu komposti soveltuu näihin erilaisiin käyttömuotoihin, etenkin kun esille tulleita kehittämistoimia toteutetaan. Sivukiven läjitysalueiden maisemoinnissa, maanviljelyssä ja metsän lannoittamisessa komposti ei tarvitse kivennäismaata seosaineeksi. Sivukiven läjitysalueilla ne kompostit, joihin oli sekoitettu hiekkaa, eivät pysyneet paikoillaan. Aines valui sadeveden mukana alas rinteeltä. Pelkkää kompostia käytettäessä kompostimassa pysyi aloillaan. Maanviljelyssä ja metsän lannoittamisessa kivennäismaa on tarpeeton. Lisäksi kompostissa oleva kiviaines kuluttaa ja voi vaurioittaa levityslaitteita. Ravinteet vapautuvat kompostista hitaasti kasvien käyttöön. Kemiallisilla lannoitteilla on nopeampi vaikutus. Kompostit soveltuvat erityisen hyvin ympäristöihin, joissa täydennyslannoitusta ei tarvita tai joissa lannoite on vaikeaa levittää. Tällaisia kohteita ovat esimerkiksi kaivosten sivukiven tai rikastushiekan läjitysalueet tai muut vaikeakulkuiset kohteet. Myös metsien lannoittaminen ja maanviljely ovat Kainuussa kompostien hyödyntämisen osalta alihyödynnettyjä. Pöyry Finland Oy on laatinut Kajaaniin kaavaillulle biologiselle jätteiden käsittelylaitokselle teknistaloudelliset suunnitelmat. Yhtiön tekemissä suunnitelmissa tulee ilmi, että kaikkien Kainuun lietteiden aumakompostointi tuottaisi kompostia 13 000 tonnia vuodessa, kun tukiaine seulotaan erilleen. Mädätys- tai biokaasulaitosvaihtoehdoissa lopputuotteen määrä on edellistä pienempi. Pelkkien Kainuun lietteiden mädättäminen tuottaisi kompostia jälkikompostin seulonnan jälkeen 6 600 tonnia. Viherrakentaminen taajamissa on komposteille Kainuussa yleinen käyttömuoto. Sillä on kasvun edellytyksiä etenkin, kun kompostin laatuun panostetaan. Viherrakentaminen Kajaanin seudulla riittäisi kuluttamaan kaiken Kainuussa muodostuvan kompostin, kun kompostimullan kulutuksena pidetään 0,5 tonnia asukasta kohden vuodessa. Tämä vastaa Kajaanin seudulla 27 000 tonnin kompostimäärää. Kompostin muodostumismäärä ei tulevaisuudessa tule olemaan lähellä tätä laskennallista multamenekkiä. Kompostin huono menekki johtuu joidenkin kuntien osalta pikemminkin huonosta kompostin laadusta kuin markkinoiden kyllästymisestä. Tilanne on korjaantumassa suunnitteilla olevan biologisen jätteiden käsittelylaitoksen myötä. Siinä kompostituotteen laatuun voidaan panostaa tehokkaammin kuin erillisillä pienillä kompostointikentillä.

Rautamalmin rikastus

Rautamalmin rikastuksessa hyödynnetään rautamineraalin ja sivukiven välisiä ominaisuuseroja, kuten tiheys-, magneettisuus- ja pintaominaisuuseroja. Yleisimmät rikastusmenetelmät ovat painovoimaerotus, magneettinen erotus ja flotaatio. Rikastusprosessi koostuu lisäksi malmin esikäsittelystä ja rikastelietteen vedenpoistosta. Rikastuksen tehokkuuteen vaikuttavat merkittävästi arvomineraalien jakautuminen malmissa, rikastuksessa käytetyt kemikaalit ja laiteominaisuudet. Näiden kehittämiseksi on tehty runsaasti tutkimuksia, joiden perusteella on voitu määritellä tietyt optimit erilaisille rikastusmenetelmille. Tässä työssä keskitytään rikastusprosessiin ja erilaisiin rikastusmenetelmiin ja siihen, kuinka ne sopivat ominaisuuksiltaan erilaisille rautamineraaleille. Lisäksi työssä otetaan huomioon rikastusprosessissa syntyvä rikastushiekka sekä sen prosessointi ja mahdollinen hyödyntäminen.

Effects of mineral sorting on concentrator design and economics

Ore sorting after crushing is an effective way to enhance the feed quality of a concentrator. Sorting by hand is the oldest way of concentrating minerals but it has become outdated because of low capacities. Older methods of sorting have also been difficult to use in large scale productions due to low capacities of sorters. Data transfer and processing and the speed of rejection mechanisms have been the bottlenecks for effective use of sorters. A fictive chalcopyrite ore body was created for this thesis. The properties of the ore were typical of chalcopyrite ores and economical limit was set for design. Concentrator capacity was determined by the size of ore body and the planned mine life. Two concentrator scenarios were compared, one with the sorting facility and the other without sorting. Comparison was made for quality and amount of feed, size of equipment and economics. Concentrator with sorting had lower investment and operational cost but also lower incomes due to the ore loss in sorting. Net cash flow, net present value and internal rate of interest were calculated for comparison of the two scenarios.

On-line determination of residual collector concentration in flotation process

Valuable minerals can be recovered by using froth flotation. This is a widely used separation technique in mineral processing. In a flotation cell hydrophobic particles attach on air bubbles dispersed in the slurry and rise on the top of the cell. Valuable particles are made hydrophobic by adding collector chemicals in the slurry. With the help of a frother reagent a stable froth forms on the top of the cell and the froth with valuable minerals, i.e. the concentrate, can be removed for further processing. Normally the collector is dosed on the basis of the feed rate of the flotation circuit and the head grade of the valuable metal. However, also the mineral composition of the ore affects the consumption of the collector, i.e. how much is adsorbed on the mineral surfaces. Therefore it is worth monitoring the residual collector concentration in the flotation tailings. Excess usage of collector causes unnecessary costs and may even disturb the process. In the literature part of the Master’s thesis the basics of flotation process and collector chemicals are introduced. Capillary electrophoresis (CE), an analytical technique suitable for detecting collector chemicals, is also reviewed. In the experimental part of the thesis the development of an on-line CE method for monitoring the concentration of collector chemicals in a flotation process and the results of a measurement campaign are presented. It was possible to determine the quality and quantity of collector chemicals in nickel flotation tailings at a concentrator plant with the developed on-line CE method. Sodium ethyl xanthate and sodium isopropyl xanthate residuals were found in the tailings and slight correlation between the measured concentrations and the dosage amounts could be seen.

Co-creating value with customers as a new approach of entering new market

Global trends associated with development of information technology, globalization, industrial and economic changes are influencing on company and customer domains and thus transforming company-customer relationship. The company centric paradigm with a strong product focus shifts to a customer oriented one with a strong emphasis on customer collaboration. As a result, the customer role changes from a passive observer to an active player. Moreover, global trends contribute to transformation of competitive environment making it tougher and simplifying an access to resources previously considered as unique. All that factors push the companies towards cooperation with customers in order to identify unarticulated needs and finding the best possible solution to existing customer problems. The Master’s Thesis is done for Outotec (Lappeenranta) which considers extension of dewatering business in Russian coal market. Research aims to identify key features of coal preparation and dewatering of fine coal and tailings in Russian preparation plants; analyze the state of Russian coal market and evaluate market potential for Outotec dewatering solutions. The study has a qualitative nature and implements an action research methodology that involves both creation of knowledge and introduction of changes into the system. The base for taking actions is formed by theoretical framework that targets on describing company - customer interaction and has selected co-creation as the most appropriate method of customer involvement. The integration of co-creation approach into an action research cycle allows not only fulfilling the research objectives but also facilitates organizational learning and intraorganizational collaboration, assists in establishing customer contacts and making the first steps into the market, bringing new joint projects to the company and opening real business opportunities.

Mineraalien rikastusprosessin vesijalanjälki

Mineraalien rikastamiseen käytetään useita fysikaalisia ja kemiallisia menetelmiä. Prosessi sisältää malmin hienonnuksen, rikastuksen ja lopuksi vedenpoistamisen rikastelietteestä. Malmin rikastamiseen käytetään muun muassa vaahdotusta, liuotusta, magneettista rikastusta ja tiheyseroihin perustuvia rikastusmenetelmiä. Rikastuslietteestä voidaan poistaa vettä sakeuttamalla ja suodattamalla. Rikastusprosessin ympäristövaikutuksia voidaan arvioida laskemalla tuotteen vesijalanjälki, joka kertoo valmistamiseen kulutetun veden määrän. Tässä kirjallisuustyössä esiteltiin mineraalien käsittelymenetelmiä sekä prosessijätevesien puhdistusmenetelmiä. Kirjallisuuslähteiden pohjalta selvitettiin Pyhäsalmen kaivoksella valmistetun kuparianodin vesijalanjälki sekä esitettiin menetelmiä, joilla prosessiin tarvittavan raakaveden kulutusta voitaisiin vähentää. Pyhäsalmella kuparirikasteesta valmistetun kuparianodin vesijalanjälki on 240 litraa H2O ekvivalenttia tuotettua tonnia kohden. Pyhäsalmen prosessin raakaveden kulutusta voidaan vähentää lisäämällä sisäistä vedenkierrätystä. Kalsiumsulfaatin saostuminen putkiin ja pumppuihin on ilmentynyt ongelmaksi vedenkierrätyksen lisäämisessä. Kalsiumsulfaattia voidaan erottaa vedestä membraaneihin, ioninvaihtoon ja sähkökemiaan perustuvilla tekniikoilla. Vaihtoehdossa, jossa johdetaan kaikista kolmesta vaahdotuksesta saatavat rikastuslietteen ja rikastushiekan sakeutuksien ylitteet sekä suodatuksien suodosvedet samaan vedenkäsittelyyn voidaan kattaa arviolta noin 65 % koko veden tarpeesta. Raakavettä säästetään vuodessa 3,4 Mm^3 ja samalla rikastushiekka-altaiden tarvittava koko pienenee, joka vähentää ympäristöriskejä.

Jauhatusparametrien vaikutus jauhatustuotteen partikkelikokoon ja suodattuvuuteen

Tämän diplomityön tarkoituksena on tutkia ensin jauhatusparametrien vaikutus rikastushiekan hienousasteeseen eli miten partikkelikokojakaumaa kuvaavat partikkelikoot muuttuvat. Tämän jälkeen tutkitaan miten rikastushiekan hienousasteen muuttuminen vaikuttaa jauhettujen rikastushiekkalietenäytteiden suodattuvuuteen. Partikkelikokojakauman variaatioista yritetään löytää yhteys suodinkakun ominaisvastuksen ja huokoisuuden välillä. Jauhatus suoritettiin laboratoriomittakaavan helmimyllyllä märkäjauhatuksena. Jauhatusta varten tehtiin kolmitasoinen faktorikoesuunnitelma, jossa muuttujina ovat lasihelmien halkaisija, jauhatusaika ja sekoitinelimen pyörimisnopeus. Suodatus toteutettiin vakiopainesuodatuksena kolmella eri suodatuspaineella Nutsche-suodattimella. Työn tuloksista saatiin selville, että partikkelikokojakauman leveys korreloi suodinkakun ominaisvastuksen kanssa. Kun partikkelikokojakauma leveys muuttui kapeammaksi, saatiin kakun ominaisvastus pienemmäksi ja suodatukseen kulunut aika lyheni. Kapein partikkelikokojakauman leveys saatiin suurimmalla helmen halkaisijalla, pisimmällä jauhatusajalla sekä suurimmalla sekoitusnopeudella.