Nitrogen Oxides Reduction Possibilities at Pulp Mill and Power Plant

Tutkimuksen tarkoituksena oli selvittää typenoksidien vähennysmahdollisuudet Stora Enson Varkauden tehtaiden sellutehtaalla ja voimalaitoksella. Tutkimuksessa käsiteltiin tehdasalueen suurimpia typenoksidien päästölähteitä: soodakattilaa, meesauunia, kuorikattilaa, öljykattilaa ja muovi-alumiinijakeen kaasutuslaitosta. Tutkimuksessa selvitettiin typenoksidipäästöjen syntymekanismit ja erilaisiin polttotekniikoihin soveltuvat typenoksidien vähennystekniikat. Varkauden tehtaiden typenoksidien vuosipäästö vuonna 2001 oli 836 tonnia. Kansallinen lainsäädäntö, kansainväliset sopimukset sekä paras käytettävissä oleva tekniikka (BAT) huomioiden selvitettiin kuhunkin kohteeseen parhaiten soveltuvat ratkaisut. Tutkimuksen perusteella laadittiin toimenpideohjelma, joka määrittelee suositeltavan toteutusjärjestyksen typenoksidien vähennystoimenpiteille. Toimenpideohjelman tärkeimpinä kriteereinä pidettiin vuonna 2004 tulevan uuden ympäristöluvan arvioituja luparajoja sekä toimenpiteiden kustannustehokkuutta. Toteutusjärjestyksessä ensimmäiseksi valittiin koeajojakson järjestäminen ajon optimoimiseksi kiertopetikattilalla ja toiseksi meesauunin ajon optimointi jatkuvatoimisen NOx-analysaattorin avulla. Seuraaviksi toimenpiteiksi ehdotettiin vertikaali-ilmajärjestelmän käyttöönottoa soodakattilalla sekä SNCR-järjestelmän asennusta kuorikattilalle. Saavutettava NOx-vähennys tulisi olemaan 10 – 45 % ja hinta 30 – 3573 EUR vähennettyä NOx-tonnia kohti. Tutkimuksen osana Ilmatieteen laitoksella teetetyn typenoksidien leviämisselvityksen mukaan Stora Enson tehtaiden NOx-päästöjen vaikutus Varkauden ilmanlaatuun on hyvin pieni. Suurin osa NOx-päästöistä aiheutuu liikenteestä.

Reduction of nitrogen oxide emissions in lime kiln

Different nitrogen oxide removal technologies for rotary lime kiln are studied in this thesis, the main focus being in commercial technologies. Post-combustion methods are investigated in more detail as potential possible NOx removal with combustion methods in rotary lime kiln is more limited or primary methods are already in use. However, secondary methods as NOx scrubber, SNCR or SCR technologies are not listed as the Best Available Technologies defined by European Union. BAT technologies for NOx removal in lime kiln are (1) Optimised combustion and combustion control, (2) Good mixing of fuel and air, (3) Low-NOx burner and (4) Fuel selection/low-N fuel. SNCR method is the most suitable technique for NOx removal in lime kiln when NOx removal from 50 % to 70 % is required in case primary methods are already in use or cannot be applied. In higher removal cases ammonia slip is an issue in SNCR. By using SCR better NOx reduction can be achieved but issues with catalyst materials are expected to arise because of the dust and sulphur dioxide which leads to catalyst poison formation in lower flue gas temperatures. NOx scrubbing has potential when simultaneous NOx and SO2 removal is required. The challenge is that NO cannot be scrubbed directly, but once it is oxidized to NO2 or further scrubbing can be performed as the solubility of NO2 is higher. Commercial installations have not been made regarding SNCR, SCR or NOx scrubbing regarding rotary lime kiln. For SNCR and SCR the closest references come from cement industry.

Metsäteollisuusintegraatin ympäristövaikutukset

Diplomityön tavoitteena oli selvittää Stora Enso Oyj Imatran tehtaiden ympäristövaikutuksia. Tarkastelu toteutettiin kahdella lähestymistavalla. Elinkaariarvioinnilla tarkasteltiin Imatran tehtaiden kartonki- ja paperituotannon elinkaaren aikaisia ympäristövaikutuksia. Elinkaariarvioinnin lisäksi tarkasteltiin Imatran tehtaiden aiheuttamia paikallisia ympäristövaikutuksia. Paikallisten vaikutusten arviointi perustui ensisijaisesti toiminnasta aiheutuvien päästöjen ja lainsäädännöllisesti ympäristön tilalle asetettujen vaatimusten ja tavoitetasojen vertailuun. Lisäksi työssä tehtiin arvio Imatran tehtaiden typenoksidipäästöjen vähentämisestä aiheutuvista kustannuksista. Työn teoriaosiossa tarkasteltiin elinkaariarvioinnin pääperiaatteita, paikallisten ympäristövaikutusten arviointiperusteita sekä yleisellä tasolla typenoksidipäästöjen vähentämistekniikoita. Elinkaariarvioinnissa ympäristövaikutuksiltaan merkittävimmiksi elinkaarivaiheiksi osoit-tautuivat paperin ja kartongin tuotantovaihe sekä kuljetukset. Paikallisten vaikutusten arvioinnissa todettiin tehtaiden jätevesien aiheuttavan lievää rehevöitymistä lähivaikutusalueella. Terveys- ja viihtyvyysvaikutuksista melu ja haju todettiin merkittävimmiksi. Työssä tarkastellut typenoksidipäästöjen vähentämismenetelmät osoittautuivat kalliiksi ja investoinneilla saavutetut ympäristöhyödyt vähäisiksi.

The effect of environmentally differentiated port fees to shipping companies’ environmental investments

The pressure has grown to develop cost-effective emission reduction strategies in the Baltic Sea. The forthcoming stringent regulations of the International Maritime Organization for reducing harmful emissions of shipping in the Baltic Sea are causing increasing expenses for the operators. A market-based attitude towards pricing of economic incentives could be seen as a new approach for a successful application for the additional emission reduction of nitrogen oxides (NOx). In this study the aim is to understand the phenomenon of environmentally differentiated port fees and its effects on shipping companies’ emission reduction investments. The goal is to examine empirically the real-life effects of the possible environmental differentiated port fee system and the effect of environmentally differentiated port fees on NOx reduction investments in the Baltic Sea. The research approach of this study is nomothetical. In this study research questions are answered by analyzing the broad database of the Baltic Sea fleet. Also the framework of theory is confirmed and plays an important role in analyzing the research problem. Existing investment costs of NOx emission reduction technology to ship owners are estimated and compared to investment costs with granted discounts added to the cash flows. The statistical analysis in this study is descriptive. The major statistic examination of this study is the calculation of the net present values of investments with different port fee scenarios. This is done to investigate if the NOx technology investments could be economically reasonable. Based on calculations it is clear that the effect of environmentally differentiated port fees is not adequate to compensate the total investment costs for NOx reduction. If the investment decision is made only with profitability considerations, sources will prefer to emission abatement as long as incomes from the given subsidy exceeds their abatement costs. Despite of the results, evidence was found that shipping companies are nevertheless willing to invest on voluntary emission abatement technology. In that case, investment decision could be made with criteria of, for example, sustainable strategy or brand image. Combined fairway and port fee system or governmental regulations and recommendation could also function as additional incentives to compensate the investment costs. Also, the results imply that the use of NPV is not necessarily the best method to evaluate environmental investments. If the calculations would be done with more environmental methods the results would probably be different.

Selective catalytic reduction of nitrogen oxides with ammonia in forced unsteady state reactors - Case based reasoning and mathematical model simulation reasoning

The application of forced unsteady-state reactors in case of selective catalytic reduction of nitrogen oxides (NOx) with ammonia (NH3) is sustained by the fact that favorable temperature and composition distributions which cannot be achieved in any steady-state regime can be obtained by means of unsteady-state operations. In a normal way of operation the low exothermicity of the selective catalytic reduction (SCR) reaction (usually carried out in the range of 280-350°C) is not enough to maintain by itself the chemical reaction. A normal mode of operation usually requires supply of supplementary heat increasing in this way the overall process operation cost. Through forced unsteady-state operation, the main advantage that can be obtained when exothermic reactions take place is the possibility of trapping, beside the ammonia, the moving heat wave inside the catalytic bed. The unsteady state-operation enables the exploitation of the thermal storage capacity of the catalyticbed. The catalytic bed acts as a regenerative heat exchanger allowing auto-thermal behaviour when the adiabatic temperature rise is low. Finding the optimum reactor configuration, employing the most suitable operation model and identifying the reactor behavior are highly important steps in order to configure a proper device for industrial applications. The Reverse Flow Reactor (RFR) - a forced unsteady state reactor - corresponds to the above mentioned characteristics and may be employed as an efficient device for the treatment of dilute pollutant mixtures. As a main disadvantage, beside its advantages, the RFR presents the 'wash out' phenomena. This phenomenon represents emissions of unconverted reactants at every switch of the flow direction. As a consequence our attention was focused on finding an alternative reactor configuration for RFR which is not affected by the incontrollable emissions of unconverted reactants. In this respect the Reactor Network (RN) was investigated. Its configuration consists of several reactors connected in a closed sequence, simulating a moving bed by changing the reactants feeding position. In the RN the flow direction is maintained in the same way ensuring uniformcatalyst exploitation and in the same time the 'wash out' phenomena is annulated. The simulated moving bed (SMB) can operate in transient mode giving practically constant exit concentration and high conversion levels. The main advantage of the reactor network operation is emphasizedby the possibility to obtain auto-thermal behavior with nearly uniformcatalyst utilization. However, the reactor network presents only a small range of switching times which allow to reach and to maintain an ignited state. Even so a proper study of the complex behavior of the RN may give the necessary information to overcome all the difficulties that can appear in the RN operation. The unsteady-state reactors complexity arises from the fact that these reactor types are characterized by short contact times and complex interaction between heat and mass transportphenomena. Such complex interactions can give rise to a remarkable complex dynamic behavior characterized by a set of spatial-temporal patterns, chaotic changes in concentration and traveling waves of heat or chemical reactivity. The main efforts of the current research studies concern the improvement of contact modalities between reactants, the possibility of thermal wave storage inside the reactor and the improvement of the kinetic activity of the catalyst used. Paying attention to the above mentioned aspects is important when higher activity even at low feeding temperatures and low emissions of unconverted reactants are the main operation concerns. Also, the prediction of the reactor pseudo or steady-state performance (regarding the conversion, selectivity and thermal behavior) and the dynamicreactor response during exploitation are important aspects in finding the optimal control strategy for the forced unsteady state catalytic tubular reactors. The design of an adapted reactor requires knowledge about the influence of its operating conditions on the overall process performance and a precise evaluation of the operating parameters rage for which a sustained dynamic behavior is obtained. An apriori estimation of the system parameters result in diminution of the computational efforts. Usually the convergence of unsteady state reactor systems requires integration over hundreds of cycles depending on the initial guess of the parameter values. The investigation of various operation models and thermal transfer strategies give reliable means to obtain recuperative and regenerative devices which are capable to maintain an auto-thermal behavior in case of low exothermic reactions. In the present research work a gradual analysis of the SCR of NOx with ammonia process in forced unsteady-state reactors was realized. The investigation covers the presentationof the general problematic related to the effect of noxious emissions in the environment, the analysis of the suitable catalysts types for the process, the mathematical analysis approach for modeling and finding the system solutions and the experimental investigation of the device found to be more suitable for the present process. In order to gain information about the forced unsteady state reactor design, operation, important system parameters and their values, mathematical description, mathematicalmethod for solving systems of partial differential equations and other specific aspects, in a fast and easy way, and a case based reasoning (CBR) approach has been used. This approach, using the experience of past similarproblems and their adapted solutions, may provide a method for gaining informations and solutions for new problems related to the forced unsteady state reactors technology. As a consequence a CBR system was implemented and a corresponding tool was developed. Further on, grooving up the hypothesis of isothermal operation, the investigation by means of numerical simulation of the feasibility of the SCR of NOx with ammonia in the RFRand in the RN with variable feeding position was realized. The hypothesis of non-isothermal operation was taken into account because in our opinion ifa commercial catalyst is considered, is not possible to modify the chemical activity and its adsorptive capacity to improve the operation butis possible to change the operation regime. In order to identify the most suitable device for the unsteady state reduction of NOx with ammonia, considering the perspective of recuperative and regenerative devices, a comparative analysis of the above mentioned two devices performance was realized. The assumption of isothermal conditions in the beginningof the forced unsteadystate investigation allowed the simplification of the analysis enabling to focus on the impact of the conditions and mode of operation on the dynamic features caused by the trapping of one reactant in the reactor, without considering the impact of thermal effect on overall reactor performance. The non-isothermal system approach has been investigated in order to point out the important influence of the thermal effect on overall reactor performance, studying the possibility of RFR and RN utilization as recuperative and regenerative devices and the possibility of achieving a sustained auto-thermal behavior in case of lowexothermic reaction of SCR of NOx with ammonia and low temperature gasfeeding. Beside the influence of the thermal effect, the influence of the principal operating parameters, as switching time, inlet flow rate and initial catalyst temperature have been stressed. This analysis is important not only because it allows a comparison between the two devices and optimisation of the operation, but also the switching time is the main operating parameter. An appropriate choice of this parameter enables the fulfilment of the process constraints. The level of the conversions achieved, the more uniform temperature profiles, the uniformity ofcatalyst exploitation and the much simpler mode of operation imposed the RN as a much more suitable device for SCR of NOx with ammonia, in usual operation and also in the perspective of control strategy implementation. Theoretical simplified models have also been proposed in order to describe the forced unsteady state reactors performance and to estimate their internal temperature and concentration profiles. The general idea was to extend the study of catalytic reactor dynamics taking into account the perspectives that haven't been analyzed yet. The experimental investigation ofRN revealed a good agreement between the data obtained by model simulation and the ones obtained experimentally.

FCC-yksikön NOx-päästöjen hallinta

Työssä tutkittiin typen oksidien (NOx) päästöjen muodostumista ja NOx-päästöjen poistomenetelmiä leijukatalyyttisessa krakkausyksikössä (FCC). Koeajossa Porvoon öljynjalostamon FCC-yksikössä tutkittiin NOx-päästöjen hallintaa CO-promoottorin (CO:n palamista edistävä lisäaine) annostelun avulla. Kirjallisuusosassa käsiteltiin NOx-päästöjen muodostumista FCC-yksikön regeneraattorissa. Katalyyttisten lisäaineiden vaikutusta NOx-päästöjen muodostumiseen tarkasteltiin laajasti. Katalyyttisten lisäaineiden ohella käsiteltiin muitakin NOx-päästöjen poistomenetelmiä. Koeajojen tarkoituksena oli optimoida FCC-yksikön katalyyttikiertoon annosteltavan CO-promoottorin määrä. CO-promoottorin sisältämä platina lisää NOx-päästöjen muodostumista regeneraattorissa, mutta vähentää jälkipalamista. Jälkipalamisen vuoksi regeneraattorin ylimenolinjan lämpötila nousee. Regeneraattorin ylimenolinjan lämpötila oli CO-promoottorin vähentämistä rajoittava tekijä, NOx-päästöjä pyrittiin vähentämään ilman merkittävää jälkipalamisen kasvua. Tuorekatalyytin platinapitoisuuden pienentäminen vähentää merkittävästi NOx-päästöjä.

Power Consumption in Carbon Capture and Storage Systems (CCS) and Possibilities to Reduce Power Consumption with Variable Speed Drives

The aim of this master´s thesis is to study which processes increase the auxiliary power consumption in carbon capture and storage processes and if it is possible to reduce the auxiliary power consumption with variable speed drives. Also the cost of carbon capture and storage is studied. Data about auxiliary power consumption in carbon capture is gathered from various studies and estimates made by various research centres. Based on these studies a view is presented how the power auxiliary power consumption is divided between different processes in carbon capture processes. In a literary study, the operation of three basic carbon capture systems is described. Also different methods to transport carbon dioxide and carbon dioxide storage options are described in this section. At the end of the thesis processes that consume most of the auxiliary power are defined and possibilities to reduce the auxiliary power consumption are evaluated. Cost of carbon capture, transport and storage are also evaluated at this point and in the case that the carbon capture and storage systems are fully deployed. According to the results, it can be estimated what are the processes are where variable speed drives can be used and what kind of cost and power consumption reduction could be achieved. Results also show how large a project carbon capture and storage is if it is fully deployed.

Effect of supplemental vitamin E on the performance of growing-finishing pigs fed stored versus freshly harvested barley and on the storage stability and eating quality of frozen pork

Lihasikojen E-vitamiinin tarve ruokittaessa vastapuidulla ohralla ja rehuun lisätyn E-vitamiinin vaikutus lihan pakastussäilyvyyteen ja syöntilaatuun

Growth of and partitioning between shoot and storage root of carrot in a northern climate

Selostus: Porkkanan kasvu ja biomassan jakautuminen varastojuuren ja verson välillä pohjoisissa oloissa

The effect of storage ageing and spring sprouting of seed tubers on the yield of three potato varieties in the Finnish Lapland : Research Note

Selostus: Siemenmukuloiden varastointiaikaisen lämpökäsittelyn ja kevätidätyksen vaikutus kolmen perunalajikkeen satoon Lapissa

Effect of harvest time on storage loss and sprouting in onion

Selostus: Sadonkorjuuajan vaikutus sipulin varastohävikkiin ja varastoinnin jälkeiseen versomiseen

Sodium reduction in cooked meat products by using commercial potassium phoshate mixtures

Selostus: Natriumpitoisuuden pienentäminen lihavalmisteissa korvaamalla natriumfosfaatti kaliumfosfaatilla

The impact of further tariff reduction on the EU sugar sector in the forthcoming multilateral round

Selostus: WTO:n kauppaneuvotteluissa esitettyjen tuontitullien alentamisvaihtoehtojen vaikutukset EU:n sokerimarkkinoihin

Defoliation by the common pine sawfly (Diprion pini) and subsequent growth reduction in Scots pine : a retrospective approach

Abstract

Transparent and secure remote network storage system using an untrusted server

Työssä kehitettin läpinäkyvä Internet Small Computer Systems Interface-verkkolevyä (iSCSI) käyttävä varmistusjärjestelmä. Verkkolevyn sisältö suojattiin asiakaspään salauskerroksella (dm-crypt). Järjestely mahdollisti sen, että verkkolevylle tallennetut varmuuskopiot pysyivät luottamuksellisina, vaikka levypalvelinta tarjoava taho oli joko epäluotettava tai suorastaan vihamielinen. Järjestelmän hyötykäyttöä varten kehitettiin helppokäyttöinen prototyyppisovellus. Järjestelmän riskit ja haavoittuvuudet käytiin läpi ja analysoitiin. Järjestelmälle tehtiin myös karkea kryptoanalyysi sen teknistenominaisuuksien pohjalta. Suorituskykymittaukset tehtiin sekä salatulle että salaamattomalle iSCSI-liikenteelle. Näistä todettiin, että salauksen vaikutus suorituskykyyn oli häviävän pieni jopa 100 megabittiä sekunnissa siirtävillä verkkonopeuksilla. Lisäksi pohdittiin teknologian muita sovelluskohteita ja tulevia tutkimusalueita.