Quantum transport phenomena and shallow impurity states in CdSb

This work is dedicated to investigation of the energy spectrum of one of the most anisotropic narrow-gap semiconductors, CdSb. At the beginning of the present studies even the model of its energy band structure was not clear. Measurements of galvanomagnetic effects in wide temperature range (1.6 - 300 K) and in magnetic fields up to 30 T were chosen for clarifying of the energy spectrum in the intentionally undoped CdSb single crystals and doped with shallow impurities (In, Ag). Detection of the Shubnikov - de Haas oscillations allowed estimating the fundamental energy spectrum parameters. The shapes of the Fermi surfaces of electrons (sphere) and holes (ellipsoid), the number of the equivalent extremums for valence band (2) and their positions in the Brillouin zone were determined for the first time in this work. Also anisotropy coefficients, components of the tensor of effective masses of carriers, effective masses of density of states, nonparabolicity of the conduction and valence bands, g-factor and its anisotropy for n- and p-CdSb were estimated for the first time during these studies. All the results obtained are compared with the cyclotron resonance data and the corresponding theoretical calculations for p-CdSb. This is basic information for the analyses of the complex transport properties of CdSb and for working out the energy spectrum model of the shallow energy levels of defects and impurities in this semiconductor. It was found out existence of different mechanisms of hopping conductivity in the presence of metal - insulator transition induced by magnetic field in n- and p-CdSb. Quite unusual feature opened in CdSb is that different types of hopping conductivity may take place in the same crystal depending on temperature, magnetic field or even orientation of crystal in magnetic field. Transport properties of undoped p-CdSb samples show that the anisotropy of the resistivity in weak and strong magnetic fields is determined completely by the anisotropy of the effective mass of the holes. Temperature and magnetic field dependence of the Hall coefficient and magnetoresistance is attributed to presence of two groups of holes with different concentrations and mobilities. The analysis demonstrates that below Tcr ~ 20 K and down to ~ 6 - 7 K the low-mobile carriers are itinerant holes with energy E2 ≈ 6 meV. The high-mobile carriers, at all temperatures T < Tcr, are holes activated thermally from a deeper acceptor band to itinerant states of a shallower acceptor band with energy E1 ≈ 3 meV. Analysis of temperature dependences of mobilities confirms the existence of the heavy-hole band or a non-equivalent maximum and two equivalent maxima of the light-hole valence band. Galvanomagnetic effects in n-CdSb reveal the existence of two groups of carriers. These are the electrons of a single minimum in isotropic conduction band and the itinerant electrons of the narrow impurity band, having at low temperatures the energies above the bottom of the conduction band. It is found that above this impurity band exists second impurity band of only localized states and the energy of both impurity bands depend on temperature so that they sink into the band gap when temperature is increased. The bands are splitted by the spin, and in strong magnetic fields the energy difference between them decreases and redistribution of the electrons between the two impurity bands takes place. Mobility of the conduction band carriers demonstrates that scattering in n-CdSb at low temperatures is strongly anisotropic. This is because of domination from scattering on the neutral impurity centers and increasing of the contribution to mobility from scattering by acoustic phonons when temperature increases. Metallic conductivity in zero or weak magnetic field is changed to activated conductivity with increasing of magnetic field. This exhibits a metal-insulator transition (MIT) induced by the magnetic field due to shift of the Fermi level from the interval of extended states to that of the localized states of the electron spectrum near the edge of the conduction band. The Mott variablerange hopping conductivity is observed in the low- and high-field intervals on the insulating side of the MIT. The results yield information about the density of states, the localization radius of the resonant impurity band with completely localized states and about the donor band. In high magnetic fields this band is separated from the conduction band and lies below the resonant impurity bands.

Paalutuskoneen vakavuuslaskennan kehittäminen

Tässä diplomityössä tutkitaan paalutuskoneen stabiliteetti- elivakavuuslaskennan toteuttamista yleisesti käytetyn monikappaledynamiikan ohjelmiston avulla. Vakavuuslaskenta kuuluu olennaisena osana paalutuskoneen suunnitteluun ja siitä saadut tulokset asettavat rajat massoille, joita paalutuskone pystyy turvallisesti käsittelemään. Tutkittavana kohteena oli uudentyyppinen poraavapaalutuskone, josta saatiin myös todellista mittaustietoa työssä laaditun simulointimallin toimivuuden arvioimiseksi. Työssä kokeiltiin erityisesti ohjelmiston tarjoamia keinoja laskentaprosessin yksinkertaistamiseksi jasimulointimallin käytön helpottamiseksi. Koska simulointimalli haluttiin säilyttää mahdollisimman yksinkertaisena, porakoneen komponentit mallinnettiin jäykkinä. Mallin ratkaisussa käytettiin staattista ja kvasistaattista analyysia. Dynaamisten voimien vaikutus porakoneeseen otettiin mallissa huomioon lisäämällä massakeskipisteisiin vastaavat pistevoimat.

Retentiopolymeerin optimointi täyteaineiden yhtäaikaisannostelussa

Kirjallisuusosassa perehdyttiin retentioaineisiin ja täyteaineisiin sekä retentioaineiden ja rainanmuodostusolosuhteiden vaikutukseen retentioon, vedenpoistoon ja paperin ominaisuuksiin. Tarkemmin kirjallisuusosassa keskityttiin täyteaineiden esiflokkaukseen, retentiopolymeerin adsorptioon sekä retentiopolymeerien ja täyteaineiden annostelutapoihin. Kokeellisessa osassa tutkittiin sarjaa retentiopolymeerejä, joiden varaustiheys ja moolimassa muuttuivat. Yksi polymeereistä oli kahdesta polymeeristävalmistettu suoladispersio ja yksi modifioitu kationinen PAM. Näillä polymeereillä käytiin läpi koesarjoja, joissa muutettiin täyteaineen annosteluaikaa retentiopolymeerin annosteluajan pysyessä vakiona. Lähinnä vertailtiin keskenään perinteistä annostelua, jossa täyteaine annosteltiin paljon ennen retentiopolymeeriä,ja yhtäaikaista annostelua, jossa molemmat annosteltiin yhtä aikaa lähellä perälaatikkoa. Kokeet tehtiin MBF-laitteella, jolla pystytään paperikonetta vastaaviin pulsaatiotaajuuksiin ja sillä voidaan valmistaa tasoviirakoneella valmistetunpaperin kaltaisia laboratorioarkkeja. Valmistetuista arkeista tutkittiin retentioita ja paperiteknisiä ominaisuuksia. Laboratoriokokeiden perusteella yhtäaikainen annostelu antoi paremmat täyteaineretentiot verrattaessa perinteiseen annosteluun lähes kaikissa koesarjoissa. Varsinkin lyhytketjuiset polymeerit näyttivättoimivan hyvin yhtäaikaisannostelulla, mikä saattaisi johtua siitä, että lyhyt reagointiaika sulpun kanssa on lyhytketjuisille polymeereille edullinen, sillä silloin polymeeriketjun konformaatio ei ehdi asettua liian alhaiseksi ja ketjun toimintakyky säilyy parempana. Polymeerin varaustiheyden kasvaessa riittävästi laski täyteaineretentio seuraavissa tapauksissa: SC-massa + kaoliini ja SC-massa +GCC kummallakin annostelulla sekä SC-massa + PCC A perinteisellä annostelulla. Hienopaperimassalla samaa trendiä noudatti täyteaine GCC kummallakin annostelulla, kun taas PCC H:ta käytettäessä paranivat täyteaineretentiot molemmilla annosteluilla. Retentiopolymeerin moolimassan kasvaessa riittävästi kääntyi täyteaineretentio laskuun täyteaineilla GCC ja kaoliini, kun käytettiin SC-massaa. Hienopaperimassalla GCC noudatti tätä samaa taipumusta. Sen sijaan SC-massalla PCC A:takäytettäessä täyteaineretentio puolestaan nousi hieman moolimassan kasvaessa. Näin kävi myös hienopaperimassalla, kun täyteaineena käytettiin PCC H:ta. Käytettäessä SC-massaa, perinteisellä annostelulla saatiin parempi tai yhtä hyvä valonsironta kuin yhtäaikaisella annostelulla kaikilla täyteaineilla. Tämä saattaisi johtua siitä, että yhtäaikaisannostelulla on muodostunut suurempia täyteaineflokkeja, mikä on alentanut valoa sirottavia pintoja. Täyteaineista korkeimmat valonsirontakertoimet antoi PCC A ja alhaisimmat kaoliini. PCC A:lla oli kapein partikkelikokojakauma, mikä korottaa paperin valonsirontaa. Hienopaperimassalla valonsirontakerroin ja opasiteetti suurenivat GCC-pitoisuuden kasvaessa kummallakin annostelulla, mikä voisi johtua täyteainepartikkelien antamasta paremmasta sironnasta. Yhtäaikaisella annostelulla saavutettiin huomattavasti paremmat valonsironnan arvot perinteiseen annosteluun verrattuna. PCC H-pitoisuuden kasvaessa suurenivat myös valonsirontakerroin ja opasiteetti kummallakin annostelulla. PCC H antoi korkeammat valonsirontakertoimet kuin GCC. PCC omaa suuremman valonheijastusluvun kuin GCC, minkä vuoksi se antaa paremmat valonsirontakertoimen arvot. PCC H:n partikkelikokojakauma oli myös kapeampi kuin GCC:n, mikä mahdollisti paremman valonsironnan ja opasiteetin saavuttamisen.

Muon detector link system test set-up

CERNin tutkimuskeskuksen rakenteilla olevan hadronikiihdyttimen eräs tarkoitus on todistaa Higgsin bosonin olemassaolo. Higgsin bosonin löytyminen yhtenäistäisi nykyisen hiukkasfysiikan teorian ja antaisi selityksen sille kuinka hiukkaset saavat massansa. Kiihdyttimen CMS koeasema on tarkoitettu erityisesti myonien ilmaisuun. Tämä työ liittyy CMS koeaseman RPC-ilmaisintyypin linkkijärjestelmään, jonka tarkoituksena on käsitellä ilmaisimelta tulevia myonien aiheuttamia signaaleja ja lähettää tiedot tärkeäksi katsotuista törmäystapahtumista tallennettavaksi analysointia varten. Työssä on toteutettu linkkijärjestelmän ohjaus- ja linkkikorteille testiympäristö, jolla voidaan todeta järjestelmän eri osien keskinäinen yhteensopivuus ja toimivuus. Työn alkuosassa esitellään ilmaisimen linkkijärjestelmän eri osat ja niiden merkitykset. Työn loppuosassa käydään läpi eri testimenetelmiä ja analysoidaan niiden antamia tuloksia.

A Study on Fractionation and Ultrafiltration of Proteins with Characterized Modified and Unmodified Membranes

Membrane filtration has become increasingly attractive in the processing of both foodand biotechnological products. However, the poor selectivity of the membranes and fouling are the critical factors limiting the development of UF systems for the specific fractionation of protein mixtures. This thesis gives an overview on fractionation of proteins from model protein solutions or from biological solutions. An attempt was made to improve the selectivity of the available membranes by modifying the membranes and by exploiting the different electrostatic interactions between the proteins and the membrane pore surfaces. Fractionation and UF behavior of proteins in the model solutions and in the corresponding biological solutions were compared. Characterization of the membranes and protein adsorptionto the membrane were investigated with combined flux and streaming potential studies. It has been shown that fouling of the membranes can be reduced using "self-rejecting" membranes at pH values where electrostatic repulsion is achieved between the membrane and the proteins in solution. This effect is best shown in UF of dilute single protein solutions at low ionic strengths and low pressures. Fractionation of model proteins in single, binary, and ternary solutionshas been carried out. The results have been compared to the results obtained from fractination of biological solutions. It was generally observed that fractination of proteins from biological solutions are more difficult to carry out owingto the presence of non studied protein components with different properties. Itcan be generally concluded that it is easier to enrich the smaller protein in the permeate but it is also possible to enrich the larger protein in the permeateat pH values close to the isoelectric point of the protein. It should be possible to find an optimal flux and modification to effectively improve the fractination of proteins even with very similar molar masses.

Scenario analysis in evaluation of emerging technology - Case Bluetooth

Tutkimuksen tavoitteena oli selvittää millaisia ympäristöskenaarioita tietoliikenteelle toimialana voidaan rakentaa ja mitkä näistä skenaarioista suosivat Bluetoothin diffuusiota ja kehittymistä nykyisten tuote- ja palvelunäkemysten valossa. Lisäksi pyrittiin arvioimaan, mitkä ympäristötekijät ja suuntaukset saattavat vaikuttaa Bluetoothin diffuusioon. Tutkimus rajoittui eurooppalaisen tietoliikenneympäristön tarkasteluun viiden vuoden aikana. Tietoliikennetoimialan nykytilaa ja tulevaisuutta koskevan kirjallisuuden pohjalta luotiin kolme alustavaa skenaariorunkoa. Näitä runkoja arvioitiin asiantuntijahaastattelujen avulla, jotta skenaarioista saataisiin monipuolisempia ja niiden johdonmukaisuutta voitaisiin parantaa. Lopullisia skenaarioita verrattiin Bluetoothin käyttökohteista esitettyihin näkemyksiin. Skenaarioiden teemat olivat “Fokusoidut bisnessovellukset”, “Viihdettä massoille” sekä “Tietoa kaikille”. Havaittiin, että Bluetoothin omaksumiseen vaikuttavat eniten seuraavat tekijät: teknologian sosiaalinen hyväksyntä, toimialan halukkuus teknologian edistämiseen sekä Bluetoothin ja sen kilpailijoiden kehittyminen jatkossa.

Leptogenesis as the origin of matter-antimatter asymmetry in extra dimensional and supersymmetric models

The Standard Model of particle physics is currently the best description of fundamental particles and their interactions. All particles save the Higgs boson have been observed in particle accelerator experiments over the years. Despite the predictive power the Standard Model there are many phenomena that the scenario does not predict or explain. Among the most prominent dilemmas is matter-antimatter asymmetry, and much effort has been made in formulating scenarios that accurately predict the correct amount of matter-antimatter asymmetry in the universe. One of the most appealing explanations is baryogenesis via leptogenesis which not only serves as a mechanism of producing excess matter over antimatter but can also explain why neutrinos have very small non-zero masses. Interesting leptogenesis scenarios arise when other possible candidates of theories beyond the Standard Model are brought into the picture. In this thesis, we have studied leptogenesis in an extra dimensional framework and in a modified version of supersymmetric Standard Model. The first chapters of this thesis introduce the standard cosmological model, observations made on the photon to baryon ratio and necessary preconditions for successful baryogenesis. Baryogenesis via leptogenesis is then introduced and its connection to neutrino physics is illuminated. The final chapters concentrate on extra dimensional theories and supersymmetric models and their ability to accommodate leptogenesis. There, the results of our research are also presented.

Post-industrial 2.0 – Social Web as the second coming of the post-industrial society

This study presents a review of theories of the so-called post-industrial society, and proposes that the concept of post-industrial society can be used to understand the recent developments of the World Wide Web, often described as Web 2.0 or social Web. The study combines theories ranging from post-war management science and cultural studies to software development, and tries to build a holistic view of the development of the post-industrial society, and especially the Internet. The discourse on the emergence of a post-industrial society after the World Wars has addressed the ways in which the growing importance of information, and innovations in digital communications technology, are changing our society. It is furthermore deeply connected with the discourse on the postmodern society, which emphasizes cultural fragmentation, intertextuality, and pluralism. The Internet age is characterized by increasing masses of information that are managed through various technologies. While 1990s Internet technologies often used the network as a traditional broadcasting channel with added interactivity, Web 2.0 technologies are specifically designed to utilize the network model by facilitating communication between various services and devices, and analyzing the relationships between users and objects in order to produce intelligent insight. The wide adoption of the Internet, and recently of Internet-enabled mobile devices, is furthermore continuously producing new ways of communicating, consuming, and producing. Applications of the social Web, such as social media or social networking services, are permanently changing our traditional social, cultural, and economic practices. The study first presents an overview of the post-industrial society, the Internet, and the concept of Web 2.0. Then the concept of social Web is described with an analysis of the term social media, the brief histories of the interactive Web and social networking services, and a description of the concept ―long tail‖, used to represent the masses of information available in the Web that do not receive mainstream attention. Finally, methods for retrieving and filtering information, modeling social and cultural relationships, and communicating with customers, are presented.

Liikkuvan kivimurskaimen syötinosan rakenneanalyysi osarakennetekniikan avulla

Työn tarkoituksena oli selvittää, miten osarakennetekniikkaa voidaan soveltaa siirrettävän kivimurskaimen syötinosan simuloinnissa. Tätä tutkittiin luomalla kahdella eri ohjelmistolla simulaatiomalli syötinosasta ja mallintamalla syötinosan runko joustavaksi kappaleeksi osarakennetekniikan avulla. Luotujen simulointimallien tarkkuutta selvitettiin vertaamalla niistä saatuja rungon jännityksiä tutkittavan rakenteen rungosta mitattuihin jännityksiin. Työn tarkoituksena oli myös tutkia, miten hyvin simulaatiomallit soveltuvat käytettäväksi syötinosan tuotekehityksessä. Tässä työssä käytettiin syötinosan simulaatiomallin luomiseen ANSYS-ohjelmistoa ja ADAMS-ohjelmistoa. Simulaatiomalleihin lisättiin tutkittavasta järjestelmästä mitattu ohjaussignaali sekä syötinosan jousien arvot. Järjestelmän rakenneominaisuudet saatiin suoraan valmistajan luovuttamista tiedoista. ADAMS-ohjelmistolla mallinnetussa simulaatiomallissa runko mallinnettiin joustavaksi ANSYS-ohjelmistossa, josta se siirrettiin ADAMS-ohjelmistoon. Saaduista tuloksista kävi ilmi, että osarakennetekniikkaa voidaan hyödyntää syötinosan joustavan rungon simuloinnissa. Tutkittavasta järjestelmästä mitatuissa jännityksissä ja simulaatiomalleista saaduissa jännityksissä oli eroja, mutta jännityshistorian muodot ja suuruusluokat vastasivat pääosin toisiaan. Tulosten parantamiseksi tulee selvittää lisää alkuarvoja tutkittavasta järjestelmästä ja varmistua nyt saatujen jousiparametrien oikeellisuudesta.

Feasibility of ASH DEC‐ process in treating sewage sludge and manure ash in Finland

In Finland the thermal treatment of sewage sludge has been moderate in 21th century. The reason has been the high moisture content of sludge. During 2005-2008, 97-99% of sewage sludge was utilized in landscaping and agriculture. However agricultural use has been during 2005-2007 less than 3 %. The aim of national waste management plan is that by 2016 100% of sludge is used either as soil amendment or energy. The most popular utilization method for manure is spreading it on arable land. The dry manures such as poultry manure and horse manure could also be used in incineration. The ashes could be used as fertilizers and while it is not suitable as a starter fertilizer, it is suitable in maintaining P levels in the soil. One of the main drivers for more efficient nutrient management is the eutrophication in lakes and the Baltic See. ASH DEC process can be used in concentrating phosphorus rich ashes while separating the heavy metals that could be included. ASH DEC process uses thermochemical treatment to produce renewable phosphate for fertilizer production. The process includes mixing of ashes and chlorine donors and subsequent treatment in rotary kiln for 20 min in temperature of 900 – 1 050 oC. The heavy metals evaporate and P-rich product is obtained. The toxic substances are retained in air pollution control system in form of mixed metal hydroxides. The aim of conducting this study is to estimate the potential of ASH DEC process in treating phosphorus rich ashes in Finland. The masses considered in are sewage sludge, dry manure from horses, and poultry and liquid pig manure. To date the usual treatment method for sewage sludge in Finland is composting or anaerobic digestion. Part of the amount of produced sewage sludge (800 kt/a fresh mass and 160 kt/a TS) could also be incinerated and the residual ashes used in ASH DEC process. Incinerating only manure can be economically difficult to manage because the incineration of manure is in Finland considered as waste incineration. Getting a permit for waste incineration is difficult and also small scale waste incineration is too expensive. The manure could act as an additional feedstock in counties with high density of animal husbandry where the land area might not be enough for spreading of manure. Now when the manure acts as a supplementary feedstock beside sludge, the ash can’t be used directly as fertilizer. Then it could be used in ASH DEC process. The perquisite is that the manure producers could pay for the incineration, which might prove problematic.

Extraction of polymeric galactoglucomannans from spruce wood by pressurized hot water

The major type of non-cellulosic polysaccharides (hemicelluloses) in softwoods, the partly acetylated galactoglucomannans (GGMs), which comprise about 15% of spruce wood, have attracted growing interest because of their potential to become high-value products with applications in many areas. The main objective of this work was to explore the possibilities to extract galactoglucomannans in native, polymeric form in high yield from spruce wood with pressurised hot-water, and to obtain a deeper understanding of the process chemistry involved. Spruce (Picea abies) chips and ground wood particles were extracted using an accelerated solvent extractor (ASE) in the temperature range 160 – 180°C. Detailed chemical analyses were done on both the water extracts and the wood residues. As much as 80 – 90% of the GGMs in spruce wood, i.e. about 13% based on the original wood, could be extracted from ground spruce wood with pure water at 170 – 180°C with an extraction time of 60 min. GGMs comprised about 75% of the extracted carbohydrates and about 60% of the total dissolved solids. Other substances in the water extracts were xylans, arabinogalactans, pectins, lignin and acetic acid. The yields from chips were only about 60% of that from ground wood. Both the GGMs and other non-cellulosic polysaccharides were extensively hydrolysed at severe extraction conditions when pH dropped to the level of 3.5. Addition of sodium bicarbonate increased the yields of polymeric GGMs at low additions, 2.5 – 5 mM, where the end pH remained around 3.9. However, at higher addition levels the yields decreased, mainly because the acetyl groups in GGMs were split off, leading to a low solubility of GGMs. Extraction with buffered water in the pH range 3.8 – 4.4 gave similar yields as with plain water, but gave a higher yield of polymeric GGMs. Moreover, at these pH levels the hydrolysis of acetyl groups in GGMs was significantly inhibited. It was concluded that hot-water extraction of polymeric GGMs in good yields (up to 8% of wood) demands appropriate control of pH, in a narrow range about 4. These results were supported by a study of hydrolysis of GGM at constant pH in the range of 3.8 – 4.2 where a kinetic model for degradation of GGM was developed. The influence of wood particle size on hot-water extraction was studied with particles in the range of 0.1 – 2 mm. The smallest particles (< 0.1 mm) gave 20 – 40% higher total yield than the coarsest particles (1.25 – 2 mm). The difference was greatest at short extraction times. The results indicated that extraction of GGMs and other polysaccharides is limited mainly by the mass transfer in the fibre wall, and for coarse wood particles also in the wood matrix. Spruce sapwood, heartwood and thermomechnical pulp were also compared, but only small differences in yields and composition of extracts were found. Two methods for isolation and purification of polymeric GGMs, i.e. membrane filtration and precipitation in ethanol-water, were compared. Filtration through a series of membranes with different pore sizes separated GGMs of different molar masses, from polymers to oligomers. Polysaccharides with molar mass higher than 4 kDa were precipitated in ethanol-water. GGMs comprised about 80% of the precipitated polysaccharides. Other polysaccharides were mainly arabinoglucuronoxylans and pectins. The ethanol-precipitated GGMs were by 13C NMR spectroscopy verified to be very similar to GGMs extracted from spruce wood in low yield at a much lower temperature, 90°C. The obtained large body of experimental data could be utilised for further kinetic and economic calculations to optimise technical hot-water extractionof softwoods.

Suunnittelulla ja ruo´on hyötykäytöllä tehokkuutta rantojen hoitoon : Tuloksia ja kokemuksia VELHO-hankkeesta

Varsinais-Suomen ELY-keskuksen toteuttamassa VELHO-hankkeessa kehitettiin kustannustehokkaita ratkaisuja ranta-alueiden umpeenkasvun aiheuttamiin ongelmiin luomalla uusi konsepti ranta-alueiden monikäyttösuunnitteluun, edistämällä järviruo’on hyötykäyttöä ja valmistelemalla esityksiä uuteen maaseudun kehittämisohjelmaan. Tässä julkaisussa esitellään työn tulokset ja johtopäätökset. Hankkeessa laadittiin kolme ranta-alueiden monikäyttösuunnitelmaa: Mynälahden Sarsalanaukko ja Musta-aukko, Oukkulanlahti – Naantalinaukko ja Eurajoen - Luvian rannikko. Suunnitelmissa sovitettiin yhteen ranta-alueiden eri käyttömuotoja ja pyrittiin löytämään optimaalinen verkosto hyötykäyttöön leikattavien ruovikoiden, avoimena pidettävien merenrantaniittyjen ja säilytettävien ruovikoiden välille. Kustannustehokkuuteen pyrittiin kohdentamalla hoitotoimet laajoihin kokonaisuuksiin sekä järviruo’on hyötykäytöllä. Suunnitelmat laadittiin laajassa osallistavassa prosessissa. Hankkeessa laadituissa ranta-alueiden monikäyttösuunnitelmissa esitettiin erilaisia maankäyttötavoitteita ja hoitosuosituksia yli 2000 hehtaarille. Ruovikoiden ja rantaniittyjen lisäksi suunnittelun kohteena olivat myös rantojen läheiset peltoalueet, reunavyöhykkeet ja muut perinnebiotoopit. Hoitotoimilla tavoitellaan alueiden luonnon monimuotoisuuden ja vesien tilan paranemista, maiseman avartumista ja virkistyskäytön helpottumista. Ruovikoiden erilaisia leikkuumenetelmiä (talvileikkuut, vesileikkuut, maaleikkuut) testattiin 90 hehtaarin alalla. Rantaniittyjen kunnostuksessa testattiin maaleikkuun lisäksi ruovikon niittomurskausta. Ruokomassan hyötykäyttökokeissa testattiin kahden eri ruokolaadun eli tuoreen kesäruo’on ja kuivan talviruo’on esikäsittelyä ja hyötykäyttöä energiantuotannossa (poltto, biokaasutus) ja maataloudessa (maanparannusaine, viherlannoite, kuivike, katemateriaali). Maaseudun kehittämisohjelmaan tehtiin esityksiä tukimuotojen kehittämiseksi: rantaniittyjen kunnostuksen lisääminen ja hoidon laadun parantaminen, ruovikoiden vesileikkuut ravinteiden poistajina sekä ruokomassojen käyttö maan orgaanisen aineen lisääjänä. Hankkeen kokemusten mukaan yksi kustannustehokkaimmista hoito- ja käyttöketjuista on ruovikon leikkuu loppukesällä ja siitä kertyvän massan käyttö ranta-alueiden läheisillä pelloilla viherlannoitteena ja maanparannusaineena. Yhden hehtaarin ruovikon kesäleikkuulla poistetaan keskimäärin 80 kg typpeä ja 7 kg fosforia. Vesiensuojelullisten hyötyjen lisäksi leikkuulla parannetaan umpeenkasvusta kärsivien lajien elinoloja, lisätään rantojen vetovoimaisuutta ja edistetään luonnonhoitoyrittäjyyden edellytyksiä. Peltokäytössä käsittelyketju on lyhyt eikä se vaadi pitkiä kuljetusmatkoja. Ruokomassa kierrättää ravinteita takaisin pelloille ja parantaa maan rakennetta. Järviruo’on hyötykäytöllä ei pystytä kattamaan koko leikkuu- ja käyttöketjun kustannuksia. Leikkuusta ja hyötykäytöstä saatavien monien eri aineellisten ja aineettomien ekosysteemipalveluhyötyjen vuoksi toimintaan on tarpeen suunnata yhteiskunnan tukea ja luoda käytännön toteutusta edistäviä tukimuotoja. Kustannustehokkuutta voidaan edelleen parantaa laitteita ja menetelmiä kehittämällä.

Chemical derivatization of galactoglucomannan for functional materials

In the framework of the biorefinery concept researchers aspire to optimize the utilization of plant materials, such as agricultural wastes and wood. For most of the known processes, the first steps in the valorisation of biomass are the extraction and purification of the individual components. The obtained raw products by means of a controlled separation can consecutively be modified to result in biofuels or biogas for energy production, but also in value-added products such as additives and important building blocks for the chemical and material industries. Considerable efforts are undertaken in order to substitute the use of oil-based starting materials or at least minimize their processing for the production of everyday goods. Wood is one of the raw materials, which have gained large attention in the last decades and its composition has been studied in detail. Nowadays, the extraction of water-soluble hemicelluloses from wood is well known and so for example xylan can be obtained from hardwoods and O-acetyl galactoglucomannans (GGMs) from softwoods. The aim of this work was to develop water-soluble amphiphilic materials of GGM and to assess their potential use as additives. Furthermore, GGM was also applied as a crosslinker in the synthesis of functional hydrogels for the removal of toxic metals and metalloid ions from aqueous solutions. The distinguished products were obtained by several chemical approaches and analysed by nuclear magnetic resonance spectroscopy (NMR), Fourier transform infrared spectroscopy (FTIR), size exclusion chromatography (SEC), thermal gravimetric analysis (TGA), scanning electron microscope SEM, among others. Bio-based surfactants were produced by applying GGM and different fatty acids as starting materials. On one hand, GGM-grafted-fatty acids were prepared by esterification and on the other hand, well-defined GGM-block-fatty acid derivatives were obtained by linking amino-functional fatty acids to the reducing end of GGM. The reaction conditions for the syntheses were optimized and the resultant amphiphilic GGM derivatives were evaluated concerning their ability to reduce the surface tension of water as surfactants. Furthermore, the block-structured derivatives were tested in respect to their applicability as additives for the surface modification of cellulosic materials. Besides the GGM surfactants with a bio-based hydrophilic and a bio-based hydrophobic part, also GGM block-structured derivatives with a synthetic hydrophobic tail, consisting of a polydimethylsiloxane chain, were prepared and assessed for the hydrophobization of surface of nanofibrillated cellulose films. In order to generate GGM block-structured derivatives containing a synthetic tail with distinguished physical and chemical properties, as well as a tailored chain length, a controlled polymerization method was used. Therefore, firstly an initiator group was introduced at the reducing end of the GGM and consecutively single electron transfer-living radical polymerization (SET-LRP) was performed by applying three different monomers in individual reactions. For the accomplishment of the synthesis and the analysis of the products, challenges related to the solubility of the reactants had to be overcome. Overall, a synthesis route for the production of GGM block-copolymers bearing different synthetic polymer chains was developed and several derivatives were obtained. Moreover, GGM with different molar masses were, after modification, used as a crosslinker in the synthesis of functional hydrogels. Hereby, a cationic monomer was used during the free radical polymerization and the resultant hydrogels were successfully tested for the removal of chromium and arsenic ions from aqueous solutions. The hydrogel synthesis was tailored and materials with distinguished physical properties, such as the swelling rate, were obtained after purification. The results generated in this work underline the potential of bio-based products and the urge to continue carrying out research in order to be able to use more green chemicals for the manufacturing of biorenewable and biodegradable daily products.

Biogas production in regional integrated biodegradable waste treatment – Possibilities for improving energy performance and reducing GHG emissions

The greatest threat that the biodegradable waste causes on the environment is the methane produced in landfills by the decomposition of this waste. The Landfill Directive (1999/31/EC) aims to reduce the landfilling of biodegradable waste. In Finland, 31% of biodegradable municipal waste ended up into landfills in 2012. The pressure of reducing disposing into landfills is greatly increased by the forthcoming landfill ban on biodegradable waste in Finland. There is a need to discuss the need for increasing the utilization of biodegradable waste in regional renewable energy production to utilize the waste in a way that allows the best possibilities to reduce GHG emissions. The objectives of the thesis are: (1) to find important factors affecting renewable energy recovery possibilities from biodegradable waste, (2) to determine the main factors affecting the GHG balance of biogas production system and how to improve it and (3) to find ways to define energy performance of biogas production systems and what affects it. According to the thesis, the most important factors affecting the regional renewable energy possibilities from biodegradable waste are: the amount of available feedstock, properties of feedstock, selected utilization technologies, demand of energy and material products and the economic situation of utilizing the feedstocks. The biogas production by anaerobic digestion was seen as the main technology for utilizing biodegradable waste in agriculturally dense areas. The main reason for this is that manure was seen as the main feedstock, and it can be best utilized with anaerobic digestion, which can produce renewable energy while maintaining the spreading of nutrients on arable land. Biogas plants should be located close to the heat demand that would be enough to receive the produced heat also in the summer months and located close to the agricultural area where the digestate could be utilized. Another option for biogas use is to upgrade it to biomethane, which would require a location close to the natural gas grid. The most attractive masses for biogas production are municipal and industrial biodegradable waste because of gate fees the plant receives from them can provide over 80% of the income. On the other hand, directing gate fee masses for small-scale biogas plants could make dispersed biogas production more economical. In addition, the combustion of dry agricultural waste such as straw would provide a greater energy amount than utilizing them by anaerobic digestion. The complete energy performance assessment of biogas production system requires the use of more than one system boundary. These can then be used in calculating output–input ratios of biogas production, biogas plant, biogas utilization and biogas production system, which can be used to analyze different parts of the biogas production chain. At the moment, it is difficult to compare different biogas plants since there is a wide variation of definitions for energy performance of biogas production. A more consistent way of analyzing energy performance would allow comparing biogas plants with each other and other recovery systems and finding possible locations for further improvement. Both from the GHG emission balance and energy performance point of view, the energy consumption at the biogas plant was the most significant factor. Renewable energy use to fulfil the parasitic energy demand at the plant would be the most efficient way to reduce the GHG emissions at the plant. The GHG emission reductions could be increased by upgrading biogas to biomethane and displacing natural gas or petrol use in cars when compared to biogas CHP production. The emission reductions from displacing mineral fertilizers with digestate were seen less significant, and the greater N2O emissions from spreading digestate might surpass the emission reductions from displacing mineral fertilizers.