On the Application of Beam on Elastic Foundation Theory to the Analysis of Stiffened Plate Strips

The main objective of this thesis is to show that plate strips subjected to transverse line loads can be analysed by using the beam on elastic foundation (BEF) approach. It is shown that the elastic behaviour of both the centre line section of a semi infinite plate supported along two edges, and the free edge of a cantilever plate strip can be accurately predicted by calculations based on the two parameter BEF theory. The transverse bending stiffness of the plate strip forms the foundation. The foundation modulus is shown, mathematically and physically, to be the zero order term of the fourth order differential equation governing the behaviour of BEF, whereas the torsion rigidity of the plate acts like pre tension in the second order term. Direct equivalence is obtained for harmonic line loading by comparing the differential equations of Levy's method (a simply supported plate) with the BEF method. By equating the second and zero order terms of the semi infinite BEF model for each harmonic component, two parameters are obtained for a simply supported plate of width B: the characteristic length, 1/ λ, and the normalized sum, n, being the effect of axial loading and stiffening resulting from the torsion stiffness, nlin. This procedure gives the following result for the first mode when a uniaxial stress field was assumed (ν = 0): 1/λ = √2B/π and nlin = 1. For constant line loading, which is the superimposition of harmonic components, slightly differing foundation parameters are obtained when the maximum deflection and bending moment values of the theoretical plate, with v = 0, and BEF analysis solutions are equated: 1 /λ= 1.47B/π and nlin. = 0.59 for a simply supported plate; and 1/λ = 0.99B/π and nlin = 0.25 for a fixed plate. The BEF parameters of the plate strip with a free edge are determined based solely on finite element analysis (FEA) results: 1/λ = 1.29B/π and nlin. = 0.65, where B is the double width of the cantilever plate strip. The stress biaxial, v > 0, is shown not to affect the values of the BEF parameters significantly the result of the geometric nonlinearity caused by in plane, axial and biaxial loading is studied theoretically by comparing the differential equations of Levy's method with the BEF approach. The BEF model is generalised to take into account the elastic rotation stiffness of the longitudinal edges. Finally, formulae are presented that take into account the effect of Poisson's ratio, and geometric non linearity, on bending behaviour resulting from axial and transverse inplane loading. It is also shown that the BEF parameters of the semi infinite model are valid for linear elastic analysis of a plate strip of finite length. The BEF model was verified by applying it to the analysis of bending stresses caused by misalignments in a laboratory test panel. In summary, it can be concluded that the advantages of the BEF theory are that it is a simple tool, and that it is accurate enough for specific stress analysis of semi infinite and finite plate bending problems.

Colligation and Cross Moment-Based Approaches for Independent Component Analysis

Diplomityössä on käsitelty uudenlaisia menetelmiä riippumattomien komponenttien analyysiin(ICA): Menetelmät perustuvat colligaatioon ja cross-momenttiin. Colligaatio menetelmä perustuu painojen colligaatioon. Menetelmässä on käytetty kahden tyyppisiä todennäköisyysjakaumia yhden sijasta joka perustuu yleiseen itsenäisyyden kriteeriin. Työssä on käytetty colligaatio lähestymistapaa kahdella asymptoottisella esityksellä. Gram-Charlie ja Edgeworth laajennuksia käytetty arvioimaan todennäköisyyksiä näissä menetelmissä. Työssä on myös käytetty cross-momentti menetelmää joka perustuu neljännen asteen cross-momenttiin. Menetelmä on hyvin samankaltainen FastICA algoritmin kanssa. Molempia menetelmiä on tarkasteltu lineaarisella kahden itsenäisen muuttajan sekoituksella. Lähtö signaalit ja sekoitetut matriisit ovattuntemattomia signaali lähteiden määrää lukuunottamatta. Työssä on vertailtu colligaatio menetelmään ja sen modifikaatioita FastICA:an ja JADE:en. Työssä on myös tehty vertailu analyysi suorituskyvyn ja keskusprosessori ajan suhteen cross-momenttiin perustuvien menetelmien, FastICA:n ja JADE:n useiden sekoitettujen parien kanssa.

Communicating Cost Information to Design Engineers using an Activity-based Costing Method

This paper analyzes the possibilities of integrating cost information and engineering design. Special emphasis is on finding the potential of using the activity-based costing (ABC) method when formulating cost information for the needs of design engineers. This paper suggests that ABC is more useful than the traditional job order costing, but the negative issue is the fact that ABC models become easily too complicated, i.e. expensive to build and maintain, and difficult to use. For engineering design the most suitable elements of ABC are recognizing activities of the company, constructing acitivity chains, identifying resources, activity and cost drivers, as wellas calculating accurate product costs. ABC systems including numerous cost drivers can become complex. Therefore, a comprehensive ABC based cost information system for the use of design engineers should be considered criticaly. Combining the suitable ideas of ABC with engineering oriented thinking could give competentresults.

Particle transport method for convection-diffusion-reaction problems

Convective transport, both pure and combined with diffusion and reaction, can be observed in a wide range of physical and industrial applications, such as heat and mass transfer, crystal growth or biomechanics. The numerical approximation of this class of problemscan present substantial difficulties clue to regions of high gradients (steep fronts) of the solution, where generation of spurious oscillations or smearing should be precluded. This work is devoted to the development of an efficient numerical technique to deal with pure linear convection and convection-dominated problems in the frame-work of convection-diffusion-reaction systems. The particle transport method, developed in this study, is based on using rneshless numerical particles which carry out the solution along the characteristics defining the convective transport. The resolution of steep fronts of the solution is controlled by a special spacial adaptivity procedure. The serni-Lagrangian particle transport method uses an Eulerian fixed grid to represent the solution. In the case of convection-diffusion-reaction problems, the method is combined with diffusion and reaction solvers within an operator splitting approach. To transfer the solution from the particle set onto the grid, a fast monotone projection technique is designed. Our numerical results confirm that the method has a spacial accuracy of the second order and can be faster than typical grid-based methods of the same order; for pure linear convection problems the method demonstrates optimal linear complexity. The method works on structured and unstructured meshes, demonstrating a high-resolution property in the regions of steep fronts of the solution. Moreover, the particle transport method can be successfully used for the numerical simulation of the real-life problems in, for example, chemical engineering.

Studies on integrating kinematic design method with mechanical systems simulation techniques

Theultimate goal of any research in the mechanism/kinematic/design area may be called predictive design, ie the optimisation of mechanism proportions in the design stage without requiring extensive life and wear testing. This is an ambitious goal and can be realised through development and refinement of numerical (computational) technology in order to facilitate the design analysis and optimisation of complex mechanisms, mechanical components and systems. As a part of the systematic design methodology this thesis concentrates on kinematic synthesis (kinematic design and analysis) methods in the mechanism synthesis process. The main task of kinematic design is to find all possible solutions in the form of structural parameters to accomplish the desired requirements of motion. Main formulations of kinematic design can be broadly divided to exact synthesis and approximate synthesis formulations. The exact synthesis formulation is based in solving n linear or nonlinear equations in n variables and the solutions for the problem areget by adopting closed form classical or modern algebraic solution methods or using numerical solution methods based on the polynomial continuation or homotopy. The approximate synthesis formulations is based on minimising the approximation error by direct optimisation The main drawbacks of exact synthesis formulationare: (ia) limitations of number of design specifications and (iia) failure in handling design constraints- especially inequality constraints. The main drawbacks of approximate synthesis formulations are: (ib) it is difficult to choose a proper initial linkage and (iib) it is hard to find more than one solution. Recentformulations in solving the approximate synthesis problem adopts polynomial continuation providing several solutions, but it can not handle inequality const-raints. Based on the practical design needs the mixed exact-approximate position synthesis with two exact and an unlimited number of approximate positions has also been developed. The solutions space is presented as a ground pivot map but thepole between the exact positions cannot be selected as a ground pivot. In this thesis the exact synthesis problem of planar mechanism is solved by generating all possible solutions for the optimisation process ¿ including solutions in positive dimensional solution sets - within inequality constraints of structural parameters. Through the literature research it is first shown that the algebraic and numerical solution methods ¿ used in the research area of computational kinematics ¿ are capable of solving non-parametric algebraic systems of n equations inn variables and cannot handle the singularities associated with positive-dimensional solution sets. In this thesis the problem of positive-dimensional solutionsets is solved adopting the main principles from mathematical research area of algebraic geometry in solving parametric ( in the mathematical sense that all parameter values are considered ¿ including the degenerate cases ¿ for which the system is solvable ) algebraic systems of n equations and at least n+1 variables.Adopting the developed solution method in solving the dyadic equations in direct polynomial form in two- to three-precision-points it has been algebraically proved and numerically demonstrated that the map of the ground pivots is ambiguousand that the singularities associated with positive-dimensional solution sets can be solved. The positive-dimensional solution sets associated with the poles might contain physically meaningful solutions in the form of optimal defectfree mechanisms. Traditionally the mechanism optimisation of hydraulically driven boommechanisms is done at early state of the design process. This will result in optimal component design rather than optimal system level design. Modern mechanismoptimisation at system level demands integration of kinematic design methods with mechanical system simulation techniques. In this thesis a new kinematic design method for hydraulically driven boom mechanism is developed and integrated in mechanical system simulation techniques. The developed kinematic design method is based on the combinations of two-precision-point formulation and on optimisation ( with mathematical programming techniques or adopting optimisation methods based on probability and statistics ) of substructures using calculated criteria from the system level response of multidegree-of-freedom mechanisms. Eg. by adopting the mixed exact-approximate position synthesis in direct optimisation (using mathematical programming techniques) with two exact positions and an unlimitednumber of approximate positions the drawbacks of (ia)-(iib) has been cancelled.The design principles of the developed method are based on the design-tree -approach of the mechanical systems and the design method ¿ in principle ¿ is capable of capturing the interrelationship between kinematic and dynamic synthesis simultaneously when the developed kinematic design method is integrated with the mechanical system simulation techniques.

Project Success through Effective Decisions: Case Studies on Project Goal Setting, Success Evaluation and Managerial Decision Making

The objective of the thesis is to structure and model the factors that contribute to and can be used in evaluating project success. The purpose of this thesis is to enhance the understanding of three research topics. The goal setting process, success evaluation and decision-making process are studied in the context of a project, business unitand its business environment. To achieve the objective three research questionsare posed. These are 1) how to set measurable project goals, 2) how to evaluateproject success and 3) how to affect project success with managerial decisions.The main theoretical contribution comes from deriving a synthesis of these research topics which have mostly been discussed apart from each other in prior research. The research strategy of the study has features from at least the constructive, nomothetical, and decision-oriented research approaches. This strategy guides the theoretical and empirical part of the study. Relevant concepts and a framework are composed on the basis of the prior research contributions within the problem area. A literature review is used to derive constructs of factors withinthe framework. They are related to project goal setting, success evaluation, and decision making. On the basis of this, the case study method is applied to complement the framework. The empirical data includes one product development program, three construction projects, as well as one organization development, hardware/software, and marketing project in their contexts. In two of the case studiesthe analytic hierarchy process is used to formulate a hierarchical model that returns a numerical evaluation of the degree of project success. It has its origin in the solution idea which in turn has its foundation in the notion of projectsuccess. The achieved results are condensed in the form of a process model thatintegrates project goal setting, success evaluation and decision making. The process of project goal setting is analysed as a part of an open system that includes a project, the business unit and its competitive environment. Four main constructs of factors are suggested. First, the project characteristics and requirements are clarified. The second and the third construct comprise the components of client/market segment attractiveness and sources of competitive advantage. Together they determine the competitive position of a business unit. Fourth, the relevant goals and the situation of a business unit are clarified to stress their contribution to the project goals. Empirical evidence is gained on the exploitation of increased knowledge and on the reaction to changes in the business environment during a project to ensure project success. The relevance of a successful project to a company or a business unit tends to increase the higher the reference level of project goals is set. However, normal performance or sometimes performance below this normal level is intentionally accepted. Success measures make project success quantifiable. There are result-oriented, process-oriented and resource-oriented success measures. The study also links result measurements to enablers that portray the key processes. The success measures can be classified into success domains determining the areas on which success is assessed. Empiricalevidence is gained on six success domains: strategy, project implementation, product, stakeholder relationships, learning situation and company functions. However, some project goals, like safety, can be assessed using success measures that belong to two success domains. For example a safety index is used for assessing occupational safety during a project, which is related to project implementation. Product safety requirements, in turn, are connected to the product characteristics and thus to the product-related success domain. Strategic success measures can be used to weave the project phases together. Empirical evidence on their static nature is gained. In order-oriented projects the project phases are oftencontractually divided into different suppliers or contractors. A project from the supplier's perspective can represent only a part of the ¿whole project¿ viewed from the client's perspective. Therefore static success measures are mostly used within the contractually agreed project scope and duration. Proof is also acquired on the dynamic use of operational success measures. They help to focus on the key issues during each project phase. Furthermore, it is shown that the original success domains and success measures, their weights and target values can change dynamically. New success measures can replace the old ones to correspond better with the emphasis of the particular project phase. This adjustment concentrates on the key decision milestones. As a conclusion, the study suggests a combination of static and dynamic success measures. Their linkage to an incentive system can make the project management proactive, enable fast feedback and enhancethe motivation of the personnel. It is argued that the sequence of effective decisions is closely linked to the dynamic control of project success. According to the used definition, effective decisions aim at adequate decision quality and decision implementation. The findings support that project managers construct and use a chain of key decision milestones to evaluate and affect success during aproject. These milestones can be seen as a part of the business processes. Different managers prioritise the key decision milestones to a varying degree. Divergent managerial perspectives, power, responsibilities and involvement during a project offer some explanation for this. Finally, the study introduces the use ofHard Gate and Soft Gate decision milestones. The managers may use the former milestones to provide decision support on result measurements and ad hoc critical conditions. In the latter milestones they may make intermediate success evaluation also on the basis of other types of success measures, like process and resource measures.

Procurement, Quality and Productivity Enhancements and Manufacturing Strategy Formulation Applying Product Life Cycle Method

The objective of the thesis was to create a framework that can be used to define a manufacturing strategy taking advantage of the product life cycle method, which enables PQP enhancements. The starting point was to study synkron implementation of cost leadership and differentiation strategies in different stages of the life cycles. It was soon observed that Porter’s strategies were too generic for the complex and dynamic environment where customer needs deviate market and product specifically. Therefore, the strategy formulation process is based on the Terry Hill’s order-winner and qualifier concepts. The manufacturing strategy formulation is initiated with the definition of order-winning and qualifying criteria. From these criteria there can be shaped product specific proposals for action and production site specific key manufacturing tasks that they need to answer in order to meet customers and markets needs. As a future research it is suggested that the process of capturing order-winners and qualifiers should be developed so that the process would be simple and streamlined at Wallac Oy. In addition, defined strategy process should be integrated to the PerkinElmer’s SGS process. SGS (Strategic Goal Setting) is one of the PerkinElmer’s core management processes. Full Text: Null

The Architecture of a Fourth Generation Mobile Network

Neljännen sukupolven mobiiliverkot yhdistävät saumattomasti televerkot, Internetin ja niiden palvelut. Alkuperin Internetiä käytettiin vain paikallaan pysyviltä tietokoneilta perinteisten televerkkojen tarjotessa puhelin- ja datapalveluita. Neljännen sukupolven mobiiliverkkojen käyttäjät voivat käyttää sekä Internetiin perustuvia että perinteisten televerkkojen palveluita liikkuessaankin. Tämä diplomityö esittelee neljännen sukupolven mobiiliverkon yleisen arkkitehtuurin. Arkkitehtuurin perusosat kuvaillaan ja arkkitehtuuria verrataan toisen ja kolmannen sukupolven mobiiliverkkoihin. Aiheeseen liittyvät Internet-standardit esitellään ja niiden soveltuvuutta mobiiliverkkoihin pohditaan. Langattomia, lyhyen kantaman nopeita liitäntäverkkotekniikoita esitellään. Neljännen sukupolven mobiiliverkoissa tarvittavia päätelaitteiden ja käyttäjien liikkuvuuden hallintamenetelmiä esitellään. Esitelty arkkitehtuuri perustuu langattomiin, lyhyen kantaman nopeisiin liitäntäverkkotekniikoihin ja Internet-standardeihin. Arkkitehtuuri mahdollistaa yhteydet toisiin käyttäjiin ilman tietoa heidän senhetkisestä päätelaitteesta tai sijainnista. Internetin palveluitavoidaan käyttää missä tahansa neljännen sukupolven mobiiliverkon alueella. Yleiskäytöistä liikkuvuuden hallintamenetelmää yhden verkon alueelle ehdotetaan. Menetelmää voidaan käyttää yhdessä esitellyn arkkitehtuurin kanssa.

Modeling reaction kinetics and mass transfer in ozonation in water solutions

This dissertation is based on four articles dealing with modeling of ozonation. The literature part of this considers some models for hydrodynamics in bubble column simulation. A literature review of methods for obtaining mass transfer coefficients is presented. The methods presented to obtain mass transfer are general models and can be applied to any gas-liquid system. Ozonation reaction models and methods for obtaining stoichiometric coefficients and reaction rate coefficients for ozonation reactions are discussed in the final section of the literature part. In the first article, ozone gas-liquid mass transfer into water in a bubble column was investigated for different pH values. A more general method for estimation of mass transfer and Henry’s coefficient was developed from the Beltrán method. The ozone volumetric mass transfer coefficient and the Henry’s coefficient were determined simultaneously by parameter estimation using a nonlinear optimization method. A minor dependence of the Henry’s law constant on pH was detected at the pH range 4 - 9. In the second article, a new method using the axial dispersion model for estimation of ozone self-decomposition kinetics in a semi-batch bubble column reactor was developed. The reaction rate coefficients for literature equations of ozone decomposition and the gas phase dispersion coefficient were estimated and compared with the literature data. The reaction order in the pH range 7-10 with respect to ozone 1.12 and 0.51 the hydroxyl ion were obtained, which is in good agreement with literature. The model parameters were determined by parameter estimation using a nonlinear optimization method. Sensitivity analysis was conducted using object function method to obtain information about the reliability and identifiability of the estimated parameters. In the third article, the reaction rate coefficients and the stoichiometric coefficients in the reaction of ozone with the model component p-nitrophenol were estimated at low pH of water using nonlinear optimization. A novel method for estimation of multireaction model parameters in ozonation was developed. In this method the concentration of unknown intermediate compounds is presented as a residual COD (chemical oxygen demand) calculated from the measured COD and the theoretical COD for the known species. The decomposition rate of p-nitrophenol on the pathway producing hydroquinone was found to be about two times faster than the p-nitrophenol decomposition rate on the pathway producing 4- nitrocatechol. In the fourth article, the reaction kinetics of p-nitrophenol ozonation was studied in a bubble column at pH 2. Using the new reaction kinetic model presented in the previous article, the reaction kinetic parameters, rate coefficients, and stoichiometric coefficients as well as the mass transfer coefficient were estimated with nonlinear estimation. The decomposition rate of pnitrophenol was found to be equal both on the pathway producing hydroquinone and on the path way producing 4-nitrocathecol. Comparison of the rate coefficients with the case at initial pH 5 indicates that the p-nitrophenol degradation producing 4- nitrocathecol is more selective towards molecular ozone than the reaction producing hydroquinone. The identifiability and reliability of the estimated parameters were analyzed with the Marcov chain Monte Carlo (MCMC) method. @All rights reserved. No part of the publication may be reproduced, stored in a retrieval system, or transmitted, in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without the prior permission of the author.

Machine Learning and Clinical Text. Supporting Health Information Flow

Fluent health information flow is critical for clinical decision-making. However, a considerable part of this information is free-form text and inabilities to utilize it create risks to patient safety and cost-­effective hospital administration. Methods for automated processing of clinical text are emerging. The aim in this doctoral dissertation is to study machine learning and clinical text in order to support health information flow.First, by analyzing the content of authentic patient records, the aim is to specify clinical needs in order to guide the development of machine learning applications.The contributions are a model of the ideal information flow,a model of the problems and challenges in reality, and a road map for the technology development. Second, by developing applications for practical cases,the aim is to concretize ways to support health information flow. Altogether five machine learning applications for three practical cases are described: The first two applications are binary classification and regression related to the practical case of topic labeling and relevance ranking.The third and fourth application are supervised and unsupervised multi-class classification for the practical case of topic segmentation and labeling.These four applications are tested with Finnish intensive care patient records.The fifth application is multi-label classification for the practical task of diagnosis coding. It is tested with English radiology reports.The performance of all these applications is promising. Third, the aim is to study how the quality of machine learning applications can be reliably evaluated.The associations between performance evaluation measures and methods are addressed,and a new hold-out method is introduced.This method contributes not only to processing time but also to the evaluation diversity and quality. The main conclusion is that developing machine learning applications for text requires interdisciplinary, international collaboration. Practical cases are very different, and hence the development must begin from genuine user needs and domain expertise. The technological expertise must cover linguistics,machine learning, and information systems. Finally, the methods must be evaluated both statistically and through authentic user-feedback.

Wet oxidation of recalcitrant lignin waters: Experimental and kinetic studies

The dissertation is based on four articles dealing with recalcitrant lignin water purification. Lignin, a complicated substance and recalcitrant to most treatment technologies, inhibits seriously pulp and paper industry waste management. Therefore, lignin is studied, using WO as a process method for its degradation. A special attention is paid to the improvement in biodegradability and the reduction of lignin content, since they have special importance for any following biological treatment. In most cases wet oxidation is not used as a complete ' mineralization method but as a pre treatment in order to eliminate toxic components and to reduce the high level of organics produced. The combination of wet oxidation with a biological treatment can be a good option due to its effectiveness and its relatively low technology cost. The literature part gives an overview of Advanced Oxidation Processes (AOPs). A hot oxidation process, wet oxidation (WO), is investigated in detail and is the AOP process used in the research. The background and main principles of wet oxidation, its industrial applications, the combination of wet oxidation with other water treatment technologies, principal reactions in WO, and key aspects of modelling and reaction kinetics are presented. There is also given a wood composition and lignin characterization (chemical composition, structure and origin), lignin containing waters, lignin degradation and reuse possibilities, and purification practices for lignin containing waters. The aim of the research was to investigate the effect of the operating conditions of WO, such as temperature, partial pressure of oxygen, pH and initial concentration of wastewater, on the efficiency, and to enhance the process and estimate optimal conditions for WO of recalcitrant lignin waters. Two different waters are studied (a lignin water model solution and debarking water from paper industry) to give as appropriate conditions as possible. Due to the great importance of re using and minimizing the residues of industries, further research is carried out using residual ash of an Estonian power plant as a catalyst in wet oxidation of lignin-containing water. Developing a kinetic model that includes in the prediction such parameters as TOC gives the opportunity to estimate the amount of emerging inorganic substances (degradation rate of waste) and not only the decrease of COD and BOD. The degradation target compound, lignin is included into the model through its COD value (CODligning). Such a kinetic model can be valuable in developing WO treatment processes for lignin containing waters, or other wastewaters containing one or more target compounds. In the first article, wet oxidation of "pure" lignin water was investigated as a model case with the aim of degrading lignin and enhancing water biodegradability. The experiments were performed at various temperatures (110 -190°C), partial oxygen pressures (0.5 -1.5 MPa) and pH (5, 9 and 12). The experiments showed that increasing the temperature notably improved the processes efficiency. 75% lignin reduction was detected at the lowest temperature tested and lignin removal improved to 100% at 190°C. The effect of temperature on the COD removal rate was lower, but clearly detectable. 53% of organics were oxidized at 190°C. The effect of pH occurred mostly on lignin removal. Increasing the pH enhanced the lignin removal efficiency from 60% to nearly 100%. A good biodegradability ratio (over 0.5) was generally achieved. The aim of the second article was to develop a mathematical model for "pure" lignin wet oxidation using lumped characteristics of water (COD, BOD, TOC) and lignin concentration. The model agreed well with the experimental data (R2 = 0.93 at pH 5 and 12) and concentration changes during wet oxidation followed adequately the experimental results. The model also showed correctly the trend of biodegradability (BOD/COD) changes. In the third article, the purpose of the research was to estimate optimal conditions for wet oxidation (WO) of debarking water from the paper industry. The WO experiments were' performed at various temperatures, partial oxygen pressures and pH. The experiments showed that lignin degradation and organics removal are affected remarkably by temperature and pH. 78-97% lignin reduction was detected at different WO conditions. Initial pH 12 caused faster removal of tannins/lignin content; but initial pH 5 was more effective for removal of total organics, represented by COD and TOC. Most of the decrease in organic substances concentrations occurred in the first 60 minutes. The aim of the fourth article was to compare the behaviour of two reaction kinetic models, based on experiments of wet oxidation of industrial debarking water under different conditions. The simpler model took into account only the changes in COD, BOD and TOC; the advanced model was similar to the model used in the second article. Comparing the results of the models, the second model was found to be more suitable for describing the kinetics of wet oxidation of debarking water. The significance of the reactions involved was compared on the basis of the model: for instance, lignin degraded first to other chemically oxidizable compounds rather than directly to biodegradable products. Catalytic wet oxidation of lignin containing waters is briefly presented at the end of the dissertation. Two completely different catalysts were used: a commercial Pt catalyst and waste power plant ash. CWO showed good performance using 1 g/L of residual ash gave lignin removal of 86% and COD removal of 39% at 150°C (a lower temperature and pressure than with WO). It was noted that the ash catalyst caused a remarkable removal rate for lignin degradation already during the pre heating for `zero' time, 58% of lignin was degraded. In general, wet oxidation is not recommended for use as a complete mineralization method, but as a pre treatment phase to eliminate toxic or difficultly biodegradable components and to reduce the high level of organics. Biological treatment is an appropriate post treatment method since easily biodegradable organic matter remains after the WO process. The combination of wet oxidation with subsequent biological treatment can be an effective option for the treatment of lignin containing waters.

Financial performance of segments in the intelligent home network

The goal of this study is to examine the intelligent home business network in order to determine which part of the network has the best financial abilities to produce new business models and products/services by using financial statement analysis. A group of 377 studied limited companies is divided into four examined segments based on their offering in producing intelligent homes. The segments are customer service providers, system integrators, subsystem suppliers and component suppliers. Eight different key figures are calculated from each of the companies to get a comprehensive view of their financial performances, after which each of the segments is studied statistically to determine the performances of the whole segments. The actual performance differences between the segments are calculated by using the multi-criteria decision analysis method in which the performances of the key figures are graded and each key figure is weighted according to its importance for the goal of the study. The results of this analysis showed that subsystem suppliers have the best financial performance. Second best are system integrators, third are customer service providers and fourth component suppliers. None of the segments were strikingly poor, but even component suppliers were rather reasonable in their performance; so, it can be said that no part of the intelligent home business network has remarkably inadequate financial abilities to develop new business models and products/services.

Preferred Offer as a Method in Competitive Bidding

The objective of this master’s thesis was to find means and measures by which an industrial manufacturing company could find cost-competitive solutions in a price-driven market situation. Initially, it was essential to find individual high customer value spots from the offering. The study addressed this in an innovative way by providing the desired information for the entire range of offering. The research was carried out using the constructivist approach method. Firstly, the project and solution marketing literature was reviewed in order to establish an overview of the processes and strategies involved. This information was then used in conjunction with the company’s specific offering data to conduct a construction. This construction can be used in various functions within the target company to streamline and optimize the specifications into so-called “preferred offers”. The study also presents channels and methods with which to exploit the construction in practice in the target company. The study aimed to bring concrete improvements in competitiveness and profitability. One result of this study was the creation of a training material for internal use. This material is now used in several countries to inform and present to the staff the cost-competitive aspects of the target company’s offering.

Optimization as a method of search engine marketing

This study is dedicated to search engine marketing (SEM). It aims for developing a business model of SEM firms and to provide explicit research of trustworthy practices of virtual marketing companies. Optimization is a general term that represents a variety of techniques and methods of the web pages promotion. The research addresses optimization as a business activity, and it explains its role for the online marketing. Additionally, it highlights issues of unethical techniques utilization by marketers which created relatively negative attitude to them on the Internet environment. Literature insight combines in the one place both technical and economical scientific findings in order to highlight technological and business attributes incorporated in SEM activities. Empirical data regarding search marketers was collected via e-mail questionnaires. 4 representatives of SEM companies were engaged in this study to accomplish the business model design. Additionally, the fifth respondent was a representative of the search engine portal, who provided insight on relations between search engines and marketers. Obtained information of the respondents was processed qualitatively. Movement of commercial organizations to the online market increases demand on promotional programs. SEM is the largest part of online marketing, and it is a prerogative of search engines portals. However, skilled users, or marketers, are able to implement long-term marketing programs by utilizing web page optimization techniques, key word consultancy or content optimization to increase web site visibility to search engines and, therefore, user’s attention to the customer pages. SEM firms are related to small knowledge-intensive businesses. On the basis of data analysis the business model was constructed. The SEM model includes generalized constructs, although they represent a wider amount of operational aspects. Constructing blocks of the model includes fundamental parts of SEM commercial activity: value creation, customer, infrastructure and financial segments. Also, approaches were provided on company’s differentiation and competitive advantages evaluation. It is assumed that search marketers should apply further attempts to differentiate own business out of the large number of similar service providing companies. Findings indicate that SEM companies are interested in the increasing their trustworthiness and the reputation building. Future of the search marketing is directly depending on search engines development.

Pricing anomalies in the Finnish stock market

The aim of this thesis is to examine whether the pricing anomalies exists in the Finnish stock markets by comparing the performance of quantile portfolios that are formed on the basis of either individual valuation ratios, composite value measures or combined value and momentum indicators. All the research papers included in the thesis show evidence of value anomalies in the Finnish stock markets. In the first paper, the sample of stocks over the 1991-2006 period is divided into quintile portfolios based on four individual valuation ratios (i.e., E/P, EBITDA/EV, B/P, and S/P) and three hybrids of them (i.e. composite value measures). The results show the superiority of composite value measures as selection criterion for value stocks, particularly when EBITDA/EV is employed as earnings multiple. The main focus of the second paper is on the impact of the holding period length on performance of value strategies. As an extension to the first paper, two more individual ratios (i.e. CF/P and D/P) are included in the comparative analysis. The sample of stocks over 1993- 2008 period is divided into tercile portfolios based on six individual valuation ratios and three hybrids of them. The use of either dividend yield criterion or one of three composite value measures being examined results in best value portfolio performance according to all performance metrics used. Parallel to the findings of many international studies, our results from performance comparisons indicate that for the sample data employed, the yearly reformation of portfolios is not necessarily optimal in order to maximally gain from the value premium. Instead, the value investor may extend his holding period up to 5 years without any decrease in long-term portfolio performance. The same holds also for the results of the third paper that examines the applicability of data envelopment analysis (DEA) method in discriminating the undervalued stocks from overvalued ones. The fourth paper examines the added value of combining price momentum with various value strategies. Taking account of the price momentum improves the performance of value portfolios in most cases. The performance improvement is greatest for value portfolios that are formed on the basis of the 3-composite value measure which consists of D/P, B/P and EBITDA/EV ratios. The risk-adjusted performance can be enhanced further by following 130/30 long-short strategy in which the long position of value winner stocks is leveraged by 30 percentages while simultaneously selling short glamour loser stocks by the same amount. Average return of the long-short position proved to be more than double stock market average coupled with the volatility decrease. The fifth paper offers a new approach to combine value and momentum indicators into a single portfolio-formation criterion using different variants of DEA models. The results throughout the 1994-2010 sample period shows that the top-tercile portfolios outperform both the market portfolio and the corresponding bottom-tercile portfolios. In addition, the middle-tercile portfolios also outperform the comparable bottom-tercile portfolios when DEA models are used as a basis for stock classification criteria. To my knowledge, such strong performance differences have not been reported in earlier peer-reviewed studies that have employed the comparable quantile approach of dividing stocks into portfolios. Consistently with the previous literature, the division of the full sample period into bullish and bearish periods reveals that the top-quantile DEA portfolios lose far less of their value during the bearish conditions than do the corresponding bottom portfolios. The sixth paper extends the sample period employed in the fourth paper by one year (i.e. 1993- 2009) covering also the first years of the recent financial crisis. It contributes to the fourth paper by examining the impact of the stock market conditions on the main results. Consistently with the fifth paper, value portfolios lose much less of their value during bearish conditions than do stocks on average. The inclusion of a momentum criterion somewhat adds value to an investor during bullish conditions, but this added value turns to negative during bearish conditions. During bear market periods some of the value loser portfolios perform even better than their value winner counterparts. Furthermore, the results show that the recent financial crisis has reduced the added value of using combinations of momentum and value indicators as portfolio formation criteria. However, since the stock markets have historically been bullish more often than bearish, the combination of the value and momentum criteria has paid off to the investor despite the fact that its added value during bearish periods is negative, on an average.