Concentration of hydrogen peroxide and improving its energy efficiency

Distillation is a unit operation of process industry, which is used to separate a liquid mixture into two or more products and to concentrate liquid mixtures. A drawback of the distillation is its high energy consumption. An increase in energy and raw material prices has led to seeking ways to improve the energy efficiency of distillation. In this Master's Thesis, these ways are studied in connection with the concentration of hydrogen peroxide at the Solvay Voikkaa Plant. The aim of this thesis is to improve the energy efficiency of the concentration of the Voikkaa Plant. The work includes a review of hydrogen peroxide and its manufacturing. In addition, the fundamentals of distillation and its energy efficiency are reviewed. An energy analysis of the concentration unit of Solvay Voikkaa Plant is presented in the process development study part. It consists of the current and past information of energy and utility consumptions, balances, and costs. After that, the potential ways to improve the energy efficiency of the distillation unit at the factory are considered and their feasibility is evaluated technically and economically. Finally, proposals to improve the energy efficiency are suggested. Advanced process control, heat integration and energy efficient equipment are the most potential ways to carry out the energy efficient improvements of the concentration at the Solvay Voikkaa factory. Optimization of the reflux flow and the temperatures of the overhead condensers can offer immediate savings in the energy and utility costs without investments. Replacing the steam ejector system with a vacuum pump would result in savings of tens of thousands of euros per year. The heat pump solutions, such as utilizing a mechanical vapor recompression or thermal vapor recompression, are not feasible due to the high investment costs and long pay back times.

Teräsvalimon energia-analyysi

Teräksen valuprosessi kuluttaa runsaasti energiaa ja tuottaa merkittävästi lämpöä. Ylimääräinen lämpö on poistettava tuotantotiloista, sillä se sisältää yleensä myös paljon hiukkasia ja muita epäpuhtauksia. Lämmön talteenottaminen vähentää teräsvalimon energiankulutusta, mutta sen toteuttaminen ei ole ongelmatonta. Energia-analyysi selvittää yrityksen energian käytön ja tuotannon kehityksen sekä nykytilan. Analyysi pyrkii selvittämään kohteet, joissa energiaakuluu ja joissa sitä syntyy eniten. Tämä opinnäytetyö on sovellettu teollisuuden energia-analyysi, joka sisältää ehdotuksia energian käytöntehostamismahdollisuuksista ja säästömahdollisuuksista. Ehdotuksissa esitelläänviisi tärkeimmäksi katsottua ja kahdeksan muuta energiansäästökohdetta. Näiden lisäksi on annettu seitsemän ehdotusta muista tuotantoa ja energiansäästöä tukevista toimenpiteistä.

Energiansäästömahdollisuudet energiayhtiön toiminnassa

Työn tarkoituksena oli etsiä energian säästökohteita Etelä-Savon Energia Oy:n voimalaitos-, kaukolämpö- sekä sähkön siirto- ja jakelualalta. Työ liittyi Etelä-Savon Energia Oy:n sopimaan valtakunnalliseen energiansäästösopimukseen, jossa yhtiö sitoutui analysoimaan energian käyttönsä ja tekemään energia-analyysin pohjalta energiansäästösuunnitelman. Tässä työssä analysoitiin nykyinen energian käyttö ja etsittiin säästökohteita. Löydetyille säästökohteille määritettiin säästön sekä tarvittavan investoinnin suuruus ja suora takaisinmaksuaika investoinnille. Voimalaitoksen osalta ei löydetty suuria säästökohteita, mutta muutamia pienempiä lähinnä lämmityksiin liittyviä kohteita havaittiin. Kaukolämmön osalta säästökohteita löytyi lähinnä lämpökeskusten seisonta-aikaisista lämmityksistä, mutta kaukolämpöverkon osalta ei kannattavia säästökohteita löydetty. Sähkön siirron ja jakelun osalta loistehon kompensoinnin lisääminen vähentäisi häviöitä verkossa ja vähentäisi kompensoinnin tarvetta voimalaitoksen generaattorilla. Isoja säästökohteita ei löydetty, koska yhtiö on vuosien varrella tehostanut toimintaansa ja pienentänyt aktiivisesti energiahäviöitä.

Virtauslaskentaa ja energia-analyysiä hyödyntävä huoneilman lämpöolosuhteiden simulointimalli

Huonetilojen lämpöolosuhteiden hallinta on tärkeä osa talotekniikan suunnittelua. Tavallisesti huonetilan lämpöolosuhteita mallinnetaan menetelmillä, joissa lämpödynamiikkaa lasketaan huoneilmassa yhdessä laskentapisteessä ja rakenteissa seinäkohtaisesti. Tarkastelun kohteena on yleensä vain huoneilman lämpötila. Tämän diplomityön tavoitteena oli kehittää huoneilman lämpöolosuhteiden simulointimalli, jossa rakenteiden lämpödynamiikka lasketaan epästationaarisesti energia-analyysilaskennalla ja huoneilman virtauskenttä mallinnetaan valittuna ajanhetkenä stationaarisesti virtauslaskennalla. Tällöin virtauskentälle saadaan jakaumat suunnittelun kannalta olennaisista suureista, joita tyypillisesti ovat esimerkiksi ilman lämpötila ja nopeus. Simulointimallin laskentatuloksia verrattiin testihuonetiloissa tehtyihin mittauksiin. Tulokset osoittautuivat riittävän tarkoiksi talotekniikan suunnitteluun. Mallilla simuloitiin kaksi huonetilaa, joissa tarvittiin tavallista tarkempaa mallinnusta. Vertailulaskelmia tehtiin eri turbulenssimalleilla, diskretointitarkkuuksilla ja hilatiheyksillä. Simulointitulosten havainnollistamiseksi suunniteltiin asiakastuloste, jossa on esitetty suunnittelun kannalta olennaiset asiat. Simulointimallilla saatiin lisätietoa varsinkin lämpötilakerrostumista, joita tyypillisesti on arvioitu kokemukseen perustuen. Simulointimallin kehityksen taustana käsiteltiin rakennusten sisäilmastoa, lämpöolosuhteita ja laskentamenetelmiä sekä mallinnukseen soveltuvia kaupallisia ohjelmia. Simulointimallilla saadaan entistä tarkempaa ja yksityiskohtaisempaa tietoa lämpöolosuhteiden hallinnan suunnitteluun. Mallin käytön ongelmia ovat vielä virtauslaskennan suuri laskenta-aika, turbulenssin mallinnus, tuloilmalaitteiden reunaehtojen tarkka määritys ja laskennan konvergointi. Kehitetty simulointimalli tarjoaa hyvän perustan virtauslaskenta- ja energia-analyysiohjelmien kehittämiseksi ja yhdistämiseksi käyttäjäystävälliseksi talotekniikan suunnittelutyökaluksi.

Productizing of advanced service for power plants

Työn tavoitteena on kehittää ABB:lle palvelutuote, jota voidaan tarjota voimalaitosasiakkaille. Uuden palvelutuotteen tulee vastata ABB:n uuden strategian linjauksiin. Palvelulla tarjotaan asiakkaille 1.1.2015 voimaan tulleen energiatehokkuuslain määrittelemien pakollisten toimenpiteiden suoritusta. Työssä kerätään, käsitellään ja analysoidaan tietoa voimalaitosasiakkaille suunnatun palvelun tuotteistamisprosessin päätöksenteon tueksi. Palvelutuotteen kehittämistä varten tutkitaan ABB:n nykyisiä palvelutuotteita, osaamista ja referenssi projekteja, energiatehokkuuslakia, voimalaitosten energiatehokkuus-potentiaalia ja erilaisia energiakatselmusmalleja. Päätöksenteon tueksi tehdään referenssiprojektina energia-analyysi voimalaitokselle, jossa voimalaitoksesta tehdään ipsePRO simulointiohjelmalla mallinnus. Mallinnuksen ja koeajojen avulla tutkitaan voimalaitoksen minimikuorman optimointia. Markkinatutkimuksessa selvitetään lainsäädännön vaikutusta, nykyistä markkinatilannetta, potentiaalisia asiakkaita, kilpailijoita ja ABB:n mahdollisuuksia toimia alalla SWOT–analyysin avulla. Tutkimuksen tulosten perusteella tehdään päätös tuotteistaa voimalaitoksille palvelutuote, joka sisältää kaikki toimet energiatehokkuuslain asettamien vaatimusten täyttämiseen yrityksen energiakatselmuksen vastuuhenkilön, energiakatselmuksen ja kohdekatselmuksien teon osalta. Lisäksi työn aikana Energiavirasto myönsi ABB:lle pätevyyden toimia yrityksen energiakatselmuksen vastuuhenkilönä, mikä on edellytyksenä palvelun tarjoamiselle.

Calculation analysis of energy saving tools for fan and pump applications

This thesis analyses the calculation of FanSave and PumpSave energy saving tools calculation. With these programs energy consumption of variable speed drive control for fans and pumps can be compared to other control methods. With FanSave centrifugal and axial fans can be examined and PumpSave deals with centrifugal pumps. By means of these programs also suitable frequency converter can be chosen from the ABB collection. Programs need as initial values information about the appliances like amount of flow and efficiencies. Operation time is important factor when calculating the annual energy consumption and information about it are the length and profile. Basic theory related to fans and pumps is introduced without more precise instructions for dimensioning. FanSave and PumpSave contain various methods for flow control. These control methods are introduced in the thesis based on their operational principles and suitability. Also squirrel cage motor and frequency converter are introduced because of their close involvement to fans and pumps. Second part of the thesis contains comparison between results of FanSave’s and PumpSave’s calculation and performance curve based calculation. Also laboratory tests were made with centrifugal and axial fan and also with centrifugal pump. With the results from this thesis the calculation of these programs can be adjusted to be more accurate and also some new features can be added.

Strategic groups and performance: an empirical analysis of strategic groups in the wind energy industry in Europe

The strategic group theory provides an intermediate level of analysis between a single company and the whole industry for identifying issues about the company's competitive position and strategic choices. Strategic groups are companies within an industry with similar strategic characteristics or competing on similar bases. Strategic choices are aligned with the firms’ resources. The purpose of this study was to identify the strategic groups in the wind energy industry in Europe, and study, whether a certain group membership results in financial performance differences. Altogether 80 European wind energy companies were included in the study, which were clustered into four strategic groups according to their age and growth rate. Each group corresponds to a different strategy. The results show that the wind energy companies can be clustered according to the chosen strategic characteristics. Strategic decisions were investigated with characteristic variables. Performance variables were used in the analysis measuring profitability, liquidity and solvency of the groups. These strategic choices of the companies did not have a significant influence on the firms’ performance. The more mature and slower growing group proved to be the most successful. However, the differences between groups were generally not statistically significant. The only statistically significant difference found was in the solvency ratio between Mature Slow and Young Rapid groups. Measured with these variables, more mature and slower growing companies performed better. Therefore, a certain strategic group membership results in performance differences.

Strategic choices and performance – an empirical analysis of largest European and North American energy companies

Energy industry has gone through major changes globally in past two decades. Liberalization of energy markets has led companies to integrate both vertically and horizontally. Growing concern on sustainable development and aims to decrease greenhouse gases in future will increase the portion of renewable energy in total energy production. Purpose of this study was to analyze using statistical methods, what impacts different strategic choices has on biggest European and North American energy companies’ performance. Results show that vertical integration, horizontal integration and use of renewable energy in production had the most impact on profitability. Increase in level of vertical integration decreased companies’ profitability, while increase in horizontal integration improved companies’ profitability. Companies that used renewable energy in production were less profitable than companies not using renewable energy.

Induction Motor Drive Energy Efficiency - Simulation and Analysis

A coupled system simulator, based on analytical circuit equations and a finite element method (FEM) model of the motor has been developed and it is used to analyse a frequency-converterfed industrial squirrel-cage induction motor. Two control systems that emulate the behaviour of commercial direct-torque-controlled (DTC) and vector-controlled industrial frequency converters have been studied, implemented in the simulation software and verified by extensive laboratory tests. Numerous factors that affect the operation of a variable speed drive (VSD) and its energy efficiency have been investigated, and their significance in the simulation of the VSD results has been studied. The dependency of the frequency converter, induction motor and system losses on the switching frequency is investigated by simulations and measurements at different speeds for both the vector control and the DTC. Intensive laboratory measurements have been carried out to verify the simulation results.

Belt conveyor energy efficiency analysis and energy model development

An energy model of a belt conveyor was designed. Operation of a belt conveyor was researched. Operational indexes were calculated. Energy optimization process and recommendations were presented.

Energy and raw material consumption analysis of powder bed fusion: case study: CNC machining and laser additive manufacturing

Laser additive manufacturing (LAM), known also as 3D printing, is a powder bed fusion (PBF) type of additive manufacturing (AM) technology used to manufacture metal parts layer by layer by assist of laser beam. The development of the technology from building just prototype parts to functional parts is due to design flexibility. And also possibility to manufacture tailored and optimised components in terms of performance and strength to weight ratio of final parts. The study of energy and raw material consumption in LAM is essential as it might facilitate the adoption and usage of the technique in manufacturing industries. The objective this thesis was find the impact of LAM on environmental and economic aspects and to conduct life cycle inventory of CNC machining and LAM in terms of energy and raw material consumption at production phases. Literature overview in this thesis include sustainability issues in manufacturing industries with focus on environmental and economic aspects. Also life cycle assessment and its applicability in manufacturing industry were studied. UPLCI-CO2PE! Initiative was identified as mostly applied exiting methodology to conduct LCI analysis in discrete manufacturing process like LAM. Many of the reviewed literature had focused to PBF of polymeric material and only few had considered metallic materials. The studies that had included metallic materials had only measured input and output energy or materials of the process and compared to different AM systems without comparing to any competitive process. Neither did any include effect of process variation when building metallic parts with LAM. Experimental testing were carried out to make dissimilar samples with CNC machining and LAM in this thesis. Test samples were designed to include part complexity and weight reductions. PUMA 2500Y lathe machine was used in the CNC machining whereas a modified research machine representing EOSINT M-series was used for the LAM. The raw material used for making the test pieces were stainless steel 316L bar (CNC machined parts) and stainless steel 316L powder (LAM built parts). An analysis of power, time, and the energy consumed in each of the manufacturing processes on production phase showed that LAM utilises more energy than CNC machining. The high energy consumption was as result of duration of production. Energy consumption profiles in CNC machining showed fluctuations with high and low power ranges. LAM energy usage within specific mode (standby, heating, process, sawing) remained relatively constant through the production. CNC machining was limited in terms of manufacturing freedom as it was not possible to manufacture all the designed sample by machining. And the one which was possible was aided with large amount of material removed as waste. Planning phase in LAM was shorter than in CNC machining as the latter required many preparation steps. Specific energy consumption (SEC) were estimated in LAM based on the practical results and assumed platform utilisation. The estimated platform utilisation showed SEC could reduce when more parts were placed in one build than it was in with the empirical results in this thesis (six parts).

Performance Degradation Modelling and Techno-Economic Analysis of Lithium-Ion Battery Energy Storage Systems

Transmission system operators and distribution system operators are experiencing new challenges in terms of reliability, power quality, and cost efficiency. Although the potential of energy storages to face those challenges is recognized, the economic implications are still obscure, which introduce the risk into the business models. This thesis aims to investigate the technical and economic value indicators of lithium-ion battery energy storage systems (BESS) in grid-scale applications. In order to do that, a comprehensive performance lithium-ion BESS model with degradation effects estimation is developed. The model development process implies literature review on lifetime modelling, use, and modification of previous study progress, building the additional system parts and integrating it into a complete tool. The constructed model is capable of describing the dynamic behavior of the BESS voltage, state of charge, temperature and capacity loss. Five control strategies for BESS unit providing primary frequency regulation are implemented, in addition to the model. The questions related to BESS dimensioning and the end of life (EoL) criterion are addressed. Simulations are performed with one-month real frequency data acquired from Fingrid. The lifetime and cost-benefit analysis of the simulation results allow to compare and determine the preferable control strategy. Finally, the study performs the sensitivity analysis of economic profitability with variable size, EoL and system price. The research reports that BESS can be profitable in certain cases and presents the recommendations.

Computational and Experimental Analysis of Flow Field in the Diffusers of Centrifugal Compressors

Centrifugal compressors are widely used for example in process industry, oil and gas industry, in small gas turbines and turbochargers. In order to achieve lower consumption of energy and operation costs the efficiency of the compressor needs to be improve. In the present work different pinches and low solidity vaned diffusers were utilized in order to improve the efficiency of a medium size centrifugal compressor. In this study, pinch means the decrement of the diffuser flow passage height. First different geometries were analyzed using computational fluid dynamics. The flow solver Finflo was used to solve the flow field. Finflo is a Navier-Stokes solver. The solver is capable to solve compressible, incompressible, steady and unsteady flow fields. Chien's k-e turbulence model was used. One of the numerically investigated pinched diffuser and one low solidity vaned diffuser were studied experimentally. The overall performance of the compressor and the static pressure distribution before and after the diffuser were measured. The flow entering and leaving the diffuser was measured using a three-hole Cobra-probe and Kiel-probes. The pinch and the low solidity vaned diffuser increased the efficiency of the compressor. Highest isentropic efficiency increment obtained was 3\% of the design isentropic efficiency of the original geometry. It was noticed in the numerical results that the pinch made to the hub and the shroud wall was most beneficial to the operation of the compressor. Also the pinch made to the hub was better than the pinchmade to the shroud. The pinch did not affect the operation range of the compressor, but the low solidity vaned diffuser slightly decreased the operation range.The unsteady phenomena in the vaneless diffuser were studied experimentally andnumerically. The unsteady static pressure was measured at the diffuser inlet and outlet, and time-accurate numerical simulation was conducted. The unsteady static pressure showed that most of the pressure variations lay at the passing frequency of every second blade. The pressure variations did not vanish in the diffuser and were visible at the diffuser outlet. However, the amplitude of the pressure variations decreased in the diffuser. The time-accurate calculations showed quite a good agreement with the measured data. Agreement was very good at the design operation point, even though the computational grid was not dense enough inthe volute and in the exit cone. The time-accurate calculation over-predicted the amplitude of the pressure variations at high flow.