CO2:n käyttö puhdistuksessa ja inerttinä kaasuna öljynjalostusympäristössä

Tutkimuksen tavoitteena on löytää CO2:lle puhdistus- ja inertointikohteita öljynjalostusympäristöstä. CO2:na käytettäisiin Porvoon vetylaitokselta sivutuotteena tulevaa CO2:a. Vetylaitokselta saatava CO2-virta ei ole riittävän puhdasta käytettäväksi suoraan pesuissa ja inertoinnissa. CO2:n eri olomuotoja voidaan käyttää puhdistuksessa. Tutkimuksen lähtökohtana olleen ylikriittisen CO2:n tehokkuus perustuu sen liuottavuuteen. Huonosti liukenevien aineiden liukoisuus ylikriittiseen CO2:in paranee lisäaineiden ja pinta-aktiivisten aineiden käytöllä. Kiinteä CO2 jäädyttää ja poistaa epäpuhtauden sublimoitumisesta aiheutuvan paineaallon voimasta. Kuivajääpuhdistus soveltuu parhaiten tasaisten pintojen puhdistamiseen. Ylikriittisellä CO2:lla onnistuu nykyisellä teknologialla vain pienien kappaleiden puhdistaminen. Kuivajääpuhdistuksen toimivuutta kokeiltiin käytännössä Neste Oilin Porvoon jalostamolla hyvin tuloksin. Tasaisilta pinnoilta saatiin poistetuksi bitumia ja rasvakerros. Käyttökustannusvertailussa osoittautui ylikriittistä CO2:a käyttävä laitteisto halvemmaksi ja kuivajääpuhallus kalliimmaksi kuin konventionaaliset menetelmät. Säiliöiden paineistamiseen ja inertointiin käytetään yleisesti N2:ä. N2:llä inertoitavia kohteita voitaisiin korvata CO2:lla. CO2:n käyttöä rajoittavia seikkoja on hinta ja sen reaktiivisuus alkalimetallien kanssa. Vertailtaessa näiden kahden liukoisuuksia hiilivetyihin osoittautui CO2 monin kerroin liukoisemmaksi. Tämän ominaisuuden ansiosta CO2 voisi olla hyvä väliaine laitteiden hiilivetyvapaaksi saattamisessa.

Improvement of pyrolysis oil quality by scrubbing

Diplomityössä tutkittiin kuuman pyrolyysihöyryn puhdistamista haisevista ja kevyistä haihtuvista yhdisteistä. Työn kirjallisuusosassa selvitettiin pyrolyysiöljyn kannattavuutta uusiutuvana energialähteenä. Lisäksi eri pesurityyppejä tarkasteltiin ja ja vertailtiin. Työn kokeellisessa osassa käytettiin kahta erilaista koelaitteistoa. Tuotteen talteenotossa vertailtiin reaktorilämpötilan ja raaka-aineen kosteuden vaikutusta pyrolyysisaantoihin. Komponenttien talteenotossa tutkittiin epästabiilien ja pistävän hajuisten yhdisteiden poistamista kuumasta pyrolyysihöyrystä. Raaka-aineena käytettiin kuusen metsätäh-dehaketta, joka sisältää runsaasti neulasia ja kaarnaa. Kokeet toteutettiin lämpötila-alueella 460 - 520 °C. Koelaitteistot koostuivat kaasun (N2) syöttöjärjestelmään kytketystä kuumasta ja kyl-mästä puolesta. Tuotteen talteenotossa kuuma pyrolyysihöyry jäähdytettiin ja otettiin talteen. Komponenttien talteenotossa tuote kerättiin suodattimelle ja metyleeniklo-ridiloukkuun. Tuotteiden koostumukset analysoitiin kaasukromatokrafilla. Korkeimmat orgaaniset saannot saatiin 480 °C reaktorilämpötilalla ja 8-9 p-% raaka-ainekosteudella. Pyrolyysiveden määrä putosi raaka-aineen kosteutta nostettaessa. Eri reaktorilämpötiloilla ja raaka-ainekosteuksilla ei ollut vaikutusta hiiltosaantoihin. Kaasusaannot (pääosin CO2, CO ja hiilivedyt) olivat noin 10 p-%. Komponenttien talteenotossa suodatin tukkeutui matalissa (< 250 °C) lämpötiloissa. Suodattimelle jäänyt materiaali oli pääosin neulasista ja kaarnasta peräisin olevia uuteaineita (pääosin hartsi- rasvahappoja) ja sokereita. Korkeimmissa lämpötiloissa (> 250 °C) uuteaineet läpäisivät suodattimen paremmin. 250 ja 300 °C:n lämpötiloissa suuri määrä lyhytketjuisia helposti haihtuvia epästabiileja ja haisevia yhdisteitä (ketoneja, furaani- ja furfuraalijohdannaisia jne.) jäi metyleenikloridi- ja metanoliloukkuihin.

Eetteröintiprosessien simulointivalmiuksien kehittäminen

Diplomityön tarkoituksena oli tutkia ETBE-prosessien simulointimallin kehittämistä. Simulointia varten valittiin eetteröinnin syöttövirroiksi etanoli ja tyypillinen FCC-kolonnin hiilivetysyöttö. Kirjallisuusosassa paneuduttiin tutkimaan syitä ETBE:n käytölle bensiinissä, valmistukseen tarvittavien raaka-aineiden lähteitä ja mahdollisia korvaavia raaka-aineita sekä mietittiin etanolissa olevien epäpuhtauksien vaikutusta prosessin tuotespesifikaatioihin. Kirjallisuusosassa tarkasteltiin lisäksi eri valmistajien markkinoimia eetteröintiteknologioita. Eetteröintiteknlogiat jaettiin perinteiseen tislaukseen pohjautuviin prosesseihin, reaktiiviseen tislaukseen pohjautuviin prosesseihin sekä Neste Engineering:in markkinoimaan NExETHERS-teknologiaan. Työn kokeellisessa osassa tutkittiin sekä etanolin epäpuhtauksien kulkeutumista prosessissa että kokeellisesti saadusta höyry-nestetasapainotiedosta määritettyjen Wilsonin yhtälön binääri-interaktioparametrien vaikutusta eetteröintiprosessin simulointituloksiin. Lopuksi simulointiin prosessia, jossa oli prosessin kannalta kriittiseksi havaitut etanolin epäpuhtaudet sekä hyviksi todetut binääri-interaktioparametrit etanolin ja FCC-syöttövirran C4-hiilivetyjen välillä. Uusilla binääriparametreilla saatuja simulointituloksia vertailtiin aikaisemmin samasta mallista vanhoilla binääriparametreilla saatuihin tuloksiin. Lopuksi tehtiin yhteenveto työn tuloksista ja annettiin ehdotukset jatkotutkimuksia varten.

Sterolin valmistus selluprosessin yhteydessä

Työssä tutkittiin UPM-Kymmene Oyj Kaukaan kemiallisella tehtaalla käytössä olevia steroliprosesseja. Steroleita erotetaan sulfaattiselluloosan keitossa syntyvasta suovasta uutetusta neutraaliainejakeesta. Neutraaliaine sisältää β-sitosterolia, α-sitosterolia ja kampesterolia yhteensä noin 20 p-%. Primal-laadun valmistus perustuu neste-nesteuuttoon sekä kiteytykseen ja Ultra-laadun kaksivaiheiseen suorakiteytykseen. Työn kirjallisessa osassa perehdytään sterolien kemiaan sekä neste-nesteuuttoon ja kiteytykseen erotus- ja puhdistusmenetelminä. Laboratoriokokeissa tutkittiin kolmen eri alkoholin ja kahden eri hiilivetyliuottimen soveltuvuutta Primal-sitosterolin uuttoon ja kiteytykseen. Lisaksi tutkittiin liuotinseoksen vesipitoisuuden vaikutusta. Tavoitteena oli löytää uuttoliuottimien koostumus, jolla uuton sterolisaanto ja sterolikiteiden puhtaus olisivat mahdollisimman korkeat. Havaittiin, että uuton sterolisaanto voitiin maksimoida pitämällä uuttoalkoholin vesipitoisuus niin alhaisena, että faasit juuri ja juuri erottuvat toisistaan. Laboratoriokokeissa saatujen tulosten perusteella tehtiin tehdasmittakaavan koeajo Primal-sitosterolin valmistuslaitteistolla UPM-Kymmene Oyj Kaukaan kemiallisella tehtaalla. Talloin uutossa saavutettiin noin 50 %:n sterolisaanto. Ultra-sitosterolin laboratoriomittakaavaisissa kiteytyskokeissa vertailtiin neljän eri alkoholin ja kahden muun orgaanisen liuottimen soveltuvuutta kiteytysliuoksen komponenteiksi. Lisaksi tutkittiin vesipitoisuuden liuotinseoksen vaikutusta. Tarkoituksena oli löytää se liuotinkoostumus, jolla sterolikiteiden saanto ja puhtaus olisivat mahdollisimman korkeat. Sopivalla kiteytysliuoksen koostumuksella saavutettiin melko hyvä sterolisaanto ja lähes 98 %:n puhtaus.

Rikkiyhdisteiden laskenta simuloinneissa

Diplomityön tarkoituksena on tutkia eri laskentamenetelmien soveltuvuutta kevyiden rikkiyhdisteiden laskentaan ja kuinka mitatusta kaasu-neste tasapainotiedoista sovitetut binääriset vuorovaikutusparametrit parantavat kaasu-neste tasapainojen laskentaa simuloinneissa. Kirjallisuusosassa paneudutaan kevyisiin rikkiyhdisteisiin ja niiden aineominaisuuksiin. Lisäksi käsitellään öljynjalostuksessa nykyisin käytettäviä ja uusia kehitteillä olevia rikinpoistomenetelmiä.Kokeellisessa osassa tarkastellaan eri laskentamenetelmien soveltuvuutta rikkiyhdisteiden ja kevyiden hiilivetyjen kaasu-neste tasapainon laskentaan. Mitatusta rikkiyhdisteiden ja hiilivetyjen kaasu-neste tasapainoista sovitetaan binäärisiä vuorovaikutusparametrejä tarkentamaan käytettäviä laskentamenetelmiä. Osassa verrataan binääristen seosten mittaustuloksia eri laskentamenetelmillä saatuihin simulointituloksiin. Tarkasteluiden perusteella tehdään johtopäätöksiä laskentamenetelmien soveltuvuudesta kevyiden hiilivetyjen ja rikkiyhdisteiden laskentaan. Tarkastellaan kahden prosessin (rikkivetystripperi ja butaaninpoistokolonni) rikkiyhdisteiden laskentaa. Prosesseille tehdään taseajot, joista saatuja analyysituloksia verrataan simulointien antamiin tuloksiin. Työssä tarkastellaan myös veden liukoisuuden laskentaa ja mahdollisten laskentamenetelmien käytön vaikutusta rikkiyhdisteiden laskentaan.

Use of the Optical Cantilever Microphone in Photoacoustic Spectroscopy

A novel cantilever pressure sensor was developed in the Department of Physics at the University of Turku in order to solve the sensitivity problems which are encountered when condenser microphones are used in photoacoustic spectroscopy. The cantilever pressure sensor, combined with a laser interferometer for the measurement of the cantilever movements, proved to be highly sensitive. The original aim of this work was to integrate the sensor in a photoacoustic gas detector working in a differential measurement scheme. The integration was made successfully into three prototypes. In addition, the cantilever was also integrated in the photoacoustic FTIR measurement schemes of gas-, liquid-, and solid-phase samples. A theoretical model for the signal generation in each measurement scheme was created and the optimal celldesign discussed. The sensitivity and selectivity of the differential method were evaluated when a blackbody radiator and a mechanical chopper were used with CO₂, CH4, CO, and C2H4 gases. The detection limits were in the sub-ppm level for all four gases with only a 1.3 second integration time and the cross interference was well below one percent for all gas combinations other than those between hydrocarbons. Sensitivity with other infrared sources was compared using ethylene as an example gas. In the comparison of sensitivity with different infrared sources the electrically modulated blackbody radiator gave a 35 times higher and the CO2-laser a 100 times lower detection limit than the blackbody radiator with a mechanical chopper. As a conclusion, the differential system is well suited to rapid single gas measurements. Gas-phase photoacoustic FTIR spectroscopy gives the best performance, when several components have to be analyzed simultaneously from multicomponent samples. Multicomponent measurements were demonstrated with a sample that contained different concentrations of CO₂, H₂O, CO, and four different hydrocarbons. It required an approximately 10 times longer measurement time to achieve the same detection limit for a single gas as with the differential system. The properties of the photoacoustic FTIR spectroscopy were also compared to conventional transmission FTIR spectroscopy by simulations. Solid- and liquid-phase photoacoustic FTIR spectroscopy has several advantages compared to other techniques and therefore it also has a great variety of applications. A comparison of the signal-to-noise ratio between photoacoustic cells with a cantilever microphone and a condenser microphone was done with standard carbon black, polyethene, and sunflower oil samples. The cell with the cantilever microphone proved to have a 5-10 times higher signal-to-noise ratio than the reference detector, depending on the sample. Cantilever enhanced photoacoustics will be an effective tool for gas detection and analysis of solid- and liquid-phase samples. The preliminary prototypes gave good results in all three measurement schemes that were studied. According to simulations, there are possibilities for further enhancement of the sensitivity, as well as other properties, of each system.

Altistuminen PAH-yhdisteille kreosoottikyllästetyn puun käsittelyssä

Tässä työssä selvitettiin altistutaanko kreosoottikyllästetyn puun käsittelyssä polysyklisille aromaattisille hiilivedyille ja mistä työsuojelullisista syistä altistumista tapahtuu. Lisäksi työssä selvitettiin mitä altistuminen tarkoittaa työnantajan kannalta. Altistumista tarkasteltiin työturvallisuuden näkökulmasta. Lähtöaineisto koostui maastossa toteutetuista tutkimuksista. Aineisto kerättiin kesällä 2009 kolmesta Itä-Suomessa sijaitsevasta kohteesta, joissa käsiteltiin kreosootilla kyllästettyä puuta. Altistumisen todentamiseksi tutkimukseen osallistuneilta työntekijöiltä pyydettiin virtsanäytteet, joista analysoitiin yhden yleisimmän PAH-altistumista indikoivan merkkiaineen, virtsan 1-pyrenolin pitoisuuksia työntekijöillä. Altistumisen syiden selvittämiseksi työntekijöitä haastateltiin ja havainnoitiin. Tulosten perusteella työntekijät altistuvat PAH-yhdisteille työssään. PAH-altistumisen merkkiaineena olleelle virtsan 1-pyrenolille ei toimenpiderajaa tällä hetkellä ole, mutta se on Työterveyslaitoksella suunnitteilla. Lainsäädäntö velvoittaa erinäisin toimenpitein työnantajaa minimoimaan työntekijöiden altistumisen syöpäsairauden vaaraa aiheuttaville aineille, kuten PAH-yhdisteille. Tulosten perusteella työsuojelutoimenpiteitä on syytä tehostaa altistumisen minimoimiseksi ja etenkin ihon suojaamiseen on syytä kiinnittää erityistä huomiota.

Insulation System in an Integrated Motor Compressor

A high-speed and high-voltage solid-rotor induction machine provides beneficial features for natural gas compressor technology. The mechanical robustness of the machine enables its use in an integrated motor-compressor. The technology uses a centrifugal compressor, which is mounted on the same shaft with the high-speed electrical machine driving it. No gearbox is needed as the speed is determined by the frequency converter. The cooling is provided by the process gas, which flows through the motor and is capable of transferring the heat away from the motor. The technology has been used in the compressors in the natural gas supply chain in the central Europe. New areas of application include natural gas compressors working at the wellheads of the subsea gas reservoir. A key challenge for the design of such a motor is the resistance of the stator insulation to the raw natural gas from the well. The gas contains water and heavy hydrocarbon compounds and it is far harsher than the sales gas in the natural gas supply network. The objective of this doctoral thesis is to discuss the resistance of the insulation to the raw natural gas and the phenomena degrading the insulation. The presence of partial discharges is analyzed in this doctoral dissertation. The breakdown voltage of the gas is measured as a function of pressure and gap distance. The partial discharge activity is measured on small samples representing the windings of the machine. The electrical field behavior is also modeled by finite element methods. Based on the measurements it has been concluded that the discharges are expected to disappear at gas pressures above 4 – 5 bar. The disappearance of discharges is caused by the breakdown strength of the gas, which increases as the pressure increases. Based on the finite element analysis, the physical length of a discharge seen in the PD measurements at atmospheric pressure was approximated to be 40 – 120 m. The chemical aging of the insulation when exposed to raw natural gas is discussed based on a vast set of experimental tests with the gas mixture representing the real gas mixture at the wellhead. The mixture was created by mixing dry hydrocarbon gas, heavy hydrocarbon compounds, monoethylene glycol, and water. The mixture was chosen to be more aggressive by increasing the amount of liquid substances. Furthermore, the temperature and pressure were increased, which resulted in accelerated test conditions. The time required to detect severe degradation was thus decreased. The test program included a comparison of materials, an analysis of the e ects of di erent compounds in the gas mixture, namely water and heavy hydrocarbons, on the aging, an analysis of the e ects of temperature and exposure duration, and also an analysis on the e ect of sudden pressure changes on the degradation of the insulating materials. It was found in the tests that an insulation consisting of mica, glass, and epoxy resin can tolerate the raw natural gas, but it experiences some degradation. The key material in the composite insulation is the resin, which largely defines the performance of the insulation system. The degradation of the insulation is mostly determined by the amount of gas mixture di used into it. The di usion was seen to follow Fick’s second law, but the coe cients were not accurately defined. The di usion was not sensitive to temperature, but it was dependent upon the thermodynamic state of the gas mixture, in other words, the amounts of liquid components in the gas. The weight increase observed was mostly related to heavy hydrocarbon compounds, which act as plasticizers in the epoxy resin. The di usion of these compounds is determined by the crosslink density of the resin. Water causes slight changes in the chemical structure, but these changes do not significantly contribute to the aging phenomena. Sudden changes in pressure can lead to severe damages in the insulation, because the motion of the di used gas is able to create internal cracks in the insulation. Therefore, the di usion only reduces the mechanical strength of the insulation, but the ultimate breakdown can potentially be caused by a sudden drop in the pressure of the process gas.

Characterisation of Laser Beam and Paper Material Interaction

It is known already from 1970´s that laser beam is suitable for processing paper materials. In this thesis, term paper materials mean all wood-fibre based materials, like dried pulp, copy paper, newspaper, cardboard, corrugated board, tissue paper etc. Accordingly, laser processing in this thesis means all laser treatments resulting material removal, like cutting, partial cutting, marking, creasing, perforation etc. that can be used to process paper materials. Laser technology provides many advantages for processing of paper materials: non-contact method, freedom of processing geometry, reliable technology for non-stop production etc. Especially packaging industry is very promising area for laser processing applications. However, there are only few industrial laser processing applications worldwide even in beginning of 2010´s. One reason for small-scale use of lasers in paper material manufacturing is that there is a shortage of published research and scientific articles. Another problem, restraining the use of laser for processing of paper materials, is colouration of paper material i.e. the yellowish and/or greyish colour of cut edge appearing during cutting or after cutting. These are the main reasons for selecting the topic of this thesis to concern characterization of interaction of laser beam and paper materials. This study was carried out in Laboratory of Laser Processing at Lappeenranta University of Technology (Finland). Laser equipment used in this study was TRUMPF TLF 2700 carbon dioxide laser that produces a beam with wavelength of 10.6 μm with power range of 190-2500 W (laser power on work piece). Study of laser beam and paper material interaction was carried out by treating dried kraft pulp (grammage of 67 g m-2) with different laser power levels, focal plane postion settings and interaction times. Interaction between laser beam and dried kraft pulp was detected with different monitoring devices, i.e. spectrometer, pyrometer and active illumination imaging system. This way it was possible to create an input and output parameter diagram and to study the effects of input and output parameters in this thesis. When interaction phenomena are understood also process development can be carried out and even new innovations developed. Fulfilling the lack of information on interaction phenomena can assist in the way of lasers for wider use of technology in paper making and converting industry. It was concluded in this thesis that interaction of laser beam and paper material has two mechanisms that are dependent on focal plane position range. Assumed interaction mechanism B appears in range of average focal plane position of 3.4 mm and 2.4 mm and assumed interaction mechanism A in range of average focal plane position of 0.4 mm and -0.6 mm both in used experimental set up. Focal plane position 1.4 mm represents midzone of these two mechanisms. Holes during laser beam and paper material interaction are formed gradually: first small hole is formed to interaction area in the centre of laser beam cross-section and after that, as function of interaction time, hole expands, until interaction between laser beam and dried kraft pulp is ended. By the image analysis it can be seen that in beginning of laser beam and dried kraft pulp material interaction small holes off very good quality are formed. It is obvious that black colour and heat affected zone appear as function of interaction time. This reveals that there still are different interaction phases within interaction mechanisms A and B. These interaction phases appear as function of time and also as function of peak intensity of laser beam. Limit peak intensity is the value that divides interaction mechanism A and B from one-phase interaction into dual-phase interaction. So all peak intensity values under limit peak intensity belong to MAOM (interaction mechanism A one-phase mode) or to MBOM (interaction mechanism B onephase mode) and values over that belong to MADM (interaction mechanism A dual-phase mode) or to MBDM (interaction mechanism B dual-phase mode). Decomposition process of cellulose is evolution of hydrocarbons when temperature is between 380- 500°C. This means that long cellulose molecule is split into smaller volatile hydrocarbons in this temperature range. As temperature increases, decomposition process of cellulose molecule changes. In range of 700-900°C, cellulose molecule is mainly decomposed into H2 gas; this is why this range is called evolution of hydrogen. Interaction in this range starts (as in range of MAOM and MBOM), when a small good quality hole is formed. This is due to “direct evaporation” of pulp via decomposition process of evolution of hydrogen. And this can be seen can be seen in spectrometer as high intensity peak of yellow light (in range of 588-589 nm) which refers to temperature of ~1750ºC. Pyrometer does not detect this high intensity peak since it is not able to detect physical phase change from solid kraft pulp to gaseous compounds. As interaction time between laser beam and dried kraft pulp continues, hypothesis is that three auto ignition processes occurs. Auto ignition of substance is the lowest temperature in which it will spontaneously ignite in a normal atmosphere without an external source of ignition, such as a flame or spark. Three auto ignition processes appears in range of MADM and MBDM, namely: 1. temperature of auto ignition of hydrogen atom (H2) is 500ºC, 2. temperature of auto ignition of carbon monoxide molecule (CO) is 609ºC and 3. temperature of auto ignition of carbon atom (C) is 700ºC. These three auto ignition processes leads to formation of plasma plume which has strong emission of radiation in range of visible light. Formation of this plasma plume can be seen as increase of intensity in wavelength range of ~475-652 nm. Pyrometer shows maximum temperature just after this ignition. This plasma plume is assumed to scatter laser beam so that it interacts with larger area of dried kraft pulp than what is actual area of beam cross-section. This assumed scattering reduces also peak intensity. So result shows that assumably scattered light with low peak intensity is interacting with large area of hole edges and due to low peak intensity this interaction happens in low temperature. So interaction between laser beam and dried kraft pulp turns from evolution of hydrogen to evolution of hydrocarbons. This leads to black colour of hole edges.

Pienten yksiköiden talousveden laatuvaatimukset ja - suositukset

Talousvesi sisältää paljon erilaisia yhdisteitä, joista osa on ihmiselle haitallisia, tällaisia yhdisteitä ovat muun muassa klooratut hiilivedyt. Haitallisten yhdisteiden määrän minimoimiseksi talousvedessä talousveden vieraille aineille on määrätty asetuksissa enimmäispitoisuuksia sekä – tiheyksiä. Näitä laatuvaatimuksia sekä – suosituksia noudattamalla talousvesi on käyttökelpoista. Talousvedellä ei tällöin ole haitallisia terveysvaikutuksia eikä se vahingoita vesilinjastoja. Kirjallisuusosassa selvitetään pienten yksiköiden talousveteen liittyvän sosiaali- ja terveysministeriön asetuksen sisältöä. Mitä asetus pitää sisällään, keitä asetus koskee ja miksi asetukseen kirjatut yhdisteet ja aineet ovat ihmiselle haitallisia sekä mitä terveysvaikutuksia kyseisillä aineilla on. Kokeellisessa osiossa analysoitiin kolmesta näytteestä osa sosiaali- ja terveysministeriön asettamista vaatimuksista. Pääsääntöisesti mitattiin epäorgaanisia aineita sekä ioneja. Mittaukset suoritettiin ionikromatografilla, liekki-atomiabsorptiospektrometrillä, TOC-analysaattorilla, COD-putkilla, pH-, johtokyky- sekä sameusmittarilla.

Synthesis, characterization and chemical sensor application of conducting polymers

Polymeric materials that conduct electricity are highly interesting for fundamental studies and beneficial for modern applications in e.g. solar cells, organic field effect transistors (OFETs) as well as in chemical and bio‐sensing. Therefore, it is important to characterize this class of materials with a wide variety of methods. This work summarizes the use of electrochemistry also in combination with spectroscopic methods in synthesis and characterization of electrically conducting polymers and other π‐conjugated systems. The materials studied in this work are intended for organic electronic devices and chemical sensors. Additionally, an important part of the presented work, concerns rational approaches to the development of water‐based inks containing conducting particles. Electrochemical synthesis and electroactivity of conducting polymers can be greatly enhanced in room temperature ionic liquids (RTILs) in comparison to conventional electrolytes. Therefore, poly(para‐phyenylene) (PPP) was electrochemically synthesized in the two representative RTILs: bmimPF6 and bmiTf2N (imidazolium and pyrrolidinium‐based salts, respectively). It was found that the electrochemical synthesis of PPP was significantly enhanced in bmimPF6. Additionally, the results from doping studies of PPP films indicate improved electroactivity in bmimPF6 during oxidation (p‐doping) and in bmiTf2N in the case of reduction (n‐doping). These findings were supported by in situ infrared spectroscopy studies. Conducting poly(benzimidazobenzophenanthroline) (BBL) is a material which can provide relatively high field‐effect mobility of charge carriers in OFET devices. The main disadvantage of this n‐type semiconductor is its limited processability. Therefore in this work BBL was functionalized with poly(ethylene oxide) PEO, varying the length of side chains enabling water dispersions of the studied polymer. It was found that functionalization did not distract the electrochemical activity of the BBL backbone while the processability was improved significantly in comparison to conventional BBL. Another objective was to study highly processable poly(3,4‐ethylenedioxythiophene) poly(styrenesulfonate) (PEDOT:PSS) water‐based inks for controlled patterning scaled‐down to nearly a nanodomain with the intention to fabricate various chemical sensors. Developed PEDOT:PSS inks greatly improved printing of nanoarrays and with further modification with quaternary ammonium cations enabled fabrication of PEDOT:PSS‐based chemical sensors for lead (II) ions with enhanced adhesion and stability in aqueous environments. This opens new possibilities for development of PEDOT:PSS films that can be used in bio‐related applications. Polycyclic aromatic hydrocarbons (PAHs) are a broad group of π‐conjugated materials consisting of aromatic rings in the range from naphthalene to even hundred rings in one molecule. The research on this type of materials is intriguing, due to their interesting optical properties and resemblance of graphene. The objective was to use electrochemical synthesis to yield relatively large PAHs and fabricate electroactive films that could be used as template material in chemical sensors. Spectroscopic, electrochemical and electrical investigations evidence formation of highly stable films with fast redox response, consisting of molecules with 40 to 60 carbon atoms. Additionally, this approach in synthesis, starting from relatively small PAH molecules was successfully used in chemical sensor for lead (II).

Optimization of strength and toughness on the effect of the weldable high strength steels (hss) used in offshore structures

Optimization of high strength and toughness combination on the effect of weldability is very vital to be considered in offshore oil and gas industries. Having a balanced and improved high strength and toughness is very much recommended in offshore structures for an effective production and viable exploration of hydrocarbons. This thesis aims to investigate the possibilities to improve the toughness of high strength steel. High carbon contents induce hardness and needs to be reduced for increasing toughness. The rare combination of high strength with high toughness possibilities was examined by determining the following toughening mechanism of: Heat treatment and optimal microstructure, Thermomechanical processing, Effect of welding parameters on toughness and weldability of steel. The implementation of weldability of steels to attain high toughness for high strength in offshore structures is mostly in shipbuilding, offshore platforms, and pipelines for high operating pressures. As a result, the toughening mechanisms suggested have benefits to the aims of the effect of high strength to high toughness of steel for efficiency, production and cost reduction.

Deoxygenation of fatty acids for production of fuels and chemicals

The decreasing fossil fuel resources combined with an increasing world energy demand has raised an interest in renewable energy sources. The alternatives can be solar, wind and geothermal energies, but only biomass can be a substitute for the carbon–based feedstock, which is suitable for the production of transportation fuels and chemicals. However, a high oxygen content of the biomass creates challenges for the future chemical industry, forcing the development of new processes which allow a complete or selective oxygen removal without any significant carbon loss. Therefore, understanding and optimization of biomass deoxygenation processes are crucial for the future bio–based chemical industry. In this work, deoxygenation of fatty acids and their derivatives was studied over Pd/C and TiO2 supported noble metal catalysts (Pt, Pt–Re, Re and Ru) to obtain future fuel components. The 5 % Pd/C catalyst was investigated in semibatch and fixed bed reactors at 300 °C and 1.7–2 MPa of inert and hydrogen–containing atmospheres. Based on extensive kinetic studies, plausible reaction mechanisms and pathways were proposed. The influence of the unsaturation in the deoxygenation of model compounds and industrial feedstock – tall oil fatty acids – over a Pd/C catalyst was demonstrated. The optimization of the reaction conditions suppressed the formation of by–products, hence high yields and selectivities towards linear hydrocarbons and catalyst stability were achieved. Experiments in a fixed bed reactor filled with a 2 % Pd/C catalyst were performed with stearic acid as a model compound at different hydrogen–containing gas atmospheres to understand the catalyst stability under various conditions. Moreover, prolonged experiments were carried out with concentrated model compounds to reveal the catalyst deactivation. New materials were proposed for the selective deoxygenation process at lower temperatures (~200 °C) with a tunable selectivity to hydrodeoxygenation by using 4 % Pt/TiO2 or decarboxylation/decarbonylation over 4 % Ru/TiO2 catalysts. A new method for selective hydrogenation of fatty acids to fatty alcohols was demonstrated with a 4 % Re/TiO2 catalyst. A reaction pathway and mechanism for TiO2 supported metal catalysts was proposed and an optimization of the process conditions led to an increase in the formation of the desired products.

Thermal reactions of the major hydrocarbon components of biomass gasification gas

Gasification of biomass is an efficient method process to produce liquid fuels, heat and electricity. It is interesting especially for the Nordic countries, where raw material for the processes is readily available. The thermal reactions of light hydrocarbons are a major challenge for industrial applications. At elevated temperatures, light hydrocarbons react spontaneously to form higher molecular weight compounds. In this thesis, this phenomenon was studied by literature survey, experimental work and modeling effort. The literature survey revealed that the change in tar composition is likely caused by the kinetic entropy. The role of the surface material is deemed to be an important factor in the reactivity of the system. The experimental results were in accordance with previous publications on the subject. The novelty of the experimental work lies in the used time interval for measurements combined with an industrially relevant temperature interval. The aspects which are covered in the modeling include screening of possible numerical approaches, testing of optimization methods and kinetic modelling. No significant numerical issues were observed, so the used calculation routines are adequate for the task. Evolutionary algorithms gave a better performance combined with better fit than the conventional iterative methods such as Simplex and Levenberg-Marquardt methods. Three models were fitted on experimental data. The LLNL model was used as a reference model to which two other models were compared. A compact model which included all the observed species was developed. The parameter estimation performed on that model gave slightly impaired fit to experimental data than LLNL model, but the difference was barely significant. The third tested model concentrated on the decomposition of hydrocarbons and included a theoretical description of the formation of carbon layer on the reactor walls. The fit to experimental data was extremely good. Based on the simulation results and literature findings, it is likely that the surface coverage of carbonaceous deposits is a major factor in thermal reactions.

Surface studies of limestones and dolostones : characterisation using various techniques and batch dissolution experiments with hydrochloric acid solutions

In this thesis, stepwise titration with hydrochloric acid was used to obtain chemical reactivities and dissolution rates of ground limestones and dolostones of varying geological backgrounds (sedimentary, metamorphic or magmatic). Two different ways of conducting the calculations were used: 1) a first order mathematical model was used to calculate extrapolated initial reactivities (and dissolution rates) at pH 4, and 2) a second order mathematical model was used to acquire integrated mean specific chemical reaction constants (and dissolution rates) at pH 5. The calculations of the reactivities and dissolution rates were based on rate of change of pH and particle size distributions of the sample powders obtained by laser diffraction. The initial dissolution rates at pH 4 were repeatedly higher than previously reported literature values, whereas the dissolution rates at pH 5 were consistent with former observations. Reactivities and dissolution rates varied substantially for dolostones, whereas for limestones and calcareous rocks, the variation can be primarily explained by relatively large sample standard deviations. A list of the dolostone samples in a decreasing order of initial reactivity at pH 4 is: 1) metamorphic dolostones with calcite/dolomite ratio higher than about 6% 2) sedimentary dolostones without calcite 3) metamorphic dolostones with calcite/dolomite ratio lower than about 6% The reactivities and dissolution rates were accompanied by a wide range of experimental techniques to characterise the samples, to reveal how different rocks changed during the dissolution process, and to find out which factors had an influence on their chemical reactivities. An emphasis was put on chemical and morphological changes taking place at the surfaces of the particles via X-ray Photoelectron Spectroscopy (XPS) and Scanning Electron Microscopy (SEM). Supporting chemical information was obtained with X-Ray Fluorescence (XRF) measurements of the samples, and Inductively Coupled Plasma-Mass Spectrometry (ICP-MS) and Inductively Coupled Plasma-Optical Emission Spectrometry (ICP-OES) measurements of the solutions used in the reactivity experiments. Information on mineral (modal) compositions and their occurrence was provided by X-Ray Diffraction (XRD), Energy Dispersive X-ray analysis (EDX) and studying thin sections with a petrographic microscope. BET (Brunauer, Emmet, Teller) surface areas were determined from nitrogen physisorption data. Factors increasing chemical reactivity of dolostones and calcareous rocks were found to be sedimentary origin, higher calcite concentration and smaller quartz concentration. Also, it is assumed that finer grain size and larger BET surface areas increase the reactivity although no certain correlation was found in this thesis. Atomic concentrations did not correlate with the reactivities. Sedimentary dolostones, unlike metamorphic ones, were found to have porous surface structures after dissolution. In addition, conventional (XPS) and synchrotron based (HRXPS) X-ray Photoelectron Spectroscopy were used to study bonding environments on calcite and dolomite surfaces. Both samples are insulators, which is why neutralisation measures such as electron flood gun and a conductive mask were used. Surface core level shifts of 0.7 ± 0.1 eV for Ca 2p spectrum of calcite and 0.75 ± 0.05 eV for Mg 2p and Ca 3s spectra of dolomite were obtained. Some satellite features of Ca 2p, C 1s and O 1s spectra have been suggested to be bulk plasmons. The origin of carbide bonds was suggested to be beam assisted interaction with hydrocarbons found on the surface. The results presented in this thesis are of particular importance for choosing raw materials for wet Flue Gas Desulphurisation (FGD) and construction industry. Wet FGD benefits from high reactivity, whereas construction industry can take advantage of slow reactivity of carbonate rocks often used in the facades of fine buildings. Information on chemical bonding environments may help to create more accurate models for water-rock interactions of carbonates.