Fiber-reinforced composite fixed dental prostheses: Studies of the materials used as pontics

Fiber-reinforced composite fixed dental prostheses – Studies of the materials used as pontics University of Turku, Faculty of Medicine, Institute of Dentistry, Department of Biomaterials Science, Finnish Doctoral Program in Oral Sciences – FINDOS, Annales Universitatis Turkuensis, Turku, Finland 2015 Fiber-reinforced composites (FRC), a non-metallic biomaterial, represent a suitable alternative in prosthetic dentistry when used as a component of fixed dental prostheses (FDPs). Some drawbacks have been identified in the clinical performance of FRC restorations, such as delamination of the veneering material and fracture of the pontic. Therefore, the current series of studies were performed to investigate the possibilities of enhancing the mechanical and physical properties of FRC FDPs by improving the materials used as pontics, to then heighten their longevity. Four experiments showed the importance of the pontic design and surface treatment in the performance of FRC FDPs. In the first, the load-bearing capacities of inlay-retained FRC FDPs with pontics of various materials and thicknesses were evaluated. Three different pontic materials were assessed with different FRC framework vertical positioning. Thicker pontics showed increased load-bearing capacities, especially ceramic pontics. A second study was completed investigating the influence of the chemical conditioning of the ridge-lap surface of acrylic resin denture teeth on their bonding to a composite resin. Increased shear bond strength demonstrated the positive influence of the pretreatment of the acrylic surfaces, indicating dissolution of the denture surfaces, and suggesting potential penetration of the monomer systems into the surface of denture teeth. A third study analyzed the penetration depth of different monomer systems on the acrylic resin denture teeth surfaces. The possibility of establishing a durable bond between acrylic pontics and FRC frameworks was demonstrated by the ability of monomers to penetrate the surface of acrylic resin denture teeth, measured by a confocal scanning type microscope. A fourth study was designed to evaluate the load-bearing capacities of FRC FDPs using the findings of the previous three studies. In this case, the performance of pre-shaped acrylic resin denture teeth used as pontics with different composite resins as filling materials was evaluated. The filling material influenced the load-bearing capacities, providing more durable FRC FDPs. It can be concluded that the mechanical and physical properties of FRC FDPs can be improved as has been shown in the development of this thesis. The improvements reported then might provide long lasting prosthetic solutions of this kind, positioning them as potentially permanent rehabilitation treatments. Key words: fiber-reinforced composite, fixed dental prostheses, inlay-retained bridges, adhesion, acrylic resin denture teeth, dental material.

Unsaturated Polyester Resins from Recycled Polyethyleneterephthalate

Tämän diplomityön tarkoituksena oli tutkia miten kuluttajien kierrättämästä polyeteenitereftalaatista ( PET ) voi valmistaa tyydyttymättömiä polyesterihartseja. Työssä valmistettiin yleiskäyttöön soveltuva laminointihartsi sekä 'gel coat' -hartsi jota käytetään esim. veneiden pintamaalina. Yleishartsin depolymerointiin käytettiin propyleeniglykolia ja 'gel coat' -hartsin valmistamiseen neopentyyliglykolia. Polykondensaatiovaiheessa reaktioon lisättiin maleiinihappoa ja lopuksi hartsit liuotettiin styreeniin. Kirjallisuusosassa esitetään eri menetelmiä PET:n depolymeroimiseksi. Lisäksi esitetään eri vaihtoehtoja glykolien, happojen, katalyyttien ja vinyylimonomeerien valitsemiseksi tyydyttymättömien polyesterihartsien valmistuksessa. Analyysimenetelmiä nestemäisten ja kovetettujen hartsien tutkimiseen ja vertailuun käydään läpi kuten myös erilaisia sovelluksia polyesterihartsien käyttämiseksi. Kokeellinen osa todisti että PET-pullojäte voidaan prosessoida hartsiksiilman uusia investointeja prosessilaitteistoon. PET:n glykolyysi kesti viidestäseitsemään tuntia ja polykondensaatiovaihe kahdesta ja puolesta viiteen tuntiin. Hartsien molekyylipainot ja mekaanisten testien tulokset olivat vertailukelpoisia kaupallisten hartsien antamien tulosten kanssa. Glykolyysivaiheen momomeeri- ja oligomeeripitoisuudet mitattiin geelipermeaatiokromatografialla, jotta nähtiin miten pitkälle depolymerisaatio oli edennyt. Tätä tietoa voidaan hyödyntää uusien hartsireseptin suunnittelussa. Polymeeriketjussa jäljellä olevien C=C kaksoissidosten määrä ja niiden isomeraatioaste maleaattimuodosta fumaraattimuotoon mitattiin 1H-NMR -menetelmällä. Tislevesien koostumus määritettiin kaasukromatografialla, ja tulokset kertoivat katalyytin sisältämän kloorin reagoineen glykolien kanssa, johtaen suureen glykolikulutukseen ja muihin ei-toivottuihin sivureaktioihin. Hartsien sietokykyä auringon valolle mitattiin niiden UV-absorption avulla. Kummastakin hartsista valmistettiin 'gel coat' -maalit jotkalaitettiin sääkoneeseen, joka simuloi auringonpaistetta ja vesisadetta vuorotellen. Näistä 'gel coateista' mitattiin niiden kellastumista. Kummastakin hartsista tehdyt valut asetettiin myös sääkoneeseen ja IR-spektreistä ennen jajälkeen koetta nähtiin että C=O ja C-O esterisidoksia oli hajonnut.

Ion-exchange resins as stationary phase in reactive chromatography

Dynamic behavior of bothisothermal and non-isothermal single-column chromatographic reactors with an ion-exchange resin as the stationary phase was investigated. The reactor performance was interpreted by using results obtained when studying the effect of the resin properties on the equilibrium and kinetic phenomena occurring simultaneously in the reactor. Mathematical models were derived for each phenomenon and combined to simulate the chromatographic reactor. The phenomena studied includes phase equilibria in multicomponent liquid mixture¿ion-exchange resin systems, chemicalequilibrium in the presence of a resin catalyst, diffusion of liquids in gel-type and macroporous resins, and chemical reaction kinetics. Above all, attention was paid to the swelling behavior of the resins and how it affects the kinetic phenomena. Several poly(styrene-co-divinylbenzene) resins with different cross-link densities and internal porosities were used. Esterification of acetic acid with ethanol to produce ethyl acetate and water was used as a model reaction system. Choosing an ion-exchange resin with a low cross-link density is beneficial inthe case of the present reaction system: the amount of ethyl acetate as well the ethyl acetate to water mole ratio in the effluent stream increase with decreasing cross-link density. The enhanced performance of the reactor is mainly attributed to increasing reaction rate, which in turn originates from the phase equilibrium behavior of the system. Also mass transfer considerations favor the use ofresins with low cross-link density. The diffusion coefficients of liquids in the gel-type ion-exchange resins were found to fall rapidly when the extent of swelling became low. Glass transition of the polymer was not found to significantlyretard the diffusion in sulfonated PS¿DVB ion-exchange resins. It was also shown that non-isothermal operation of a chromatographic reactor could be used to significantly enhance the reactor performance. In the case of the exothermic modelreaction system and a near-adiabatic column, a positive thermal wave (higher temperature than in the initial state) was found to travel together with the reactive front. This further increased the conversion of the reactants. Diffusion-induced volume changes of the ion-exchange resins were studied in a flow-through cell. It was shown that describing the swelling and shrinking kinetics of the particles calls for a mass transfer model that explicitly includes the limited expansibility of the polymer network. A good description of the process was obtained by combining the generalized Maxwell-Stefan approach and an activity model that was derived from the thermodynamics of polymer solutions and gels. The swelling pressure in the resin phase was evaluated by using a non-Gaussian expression forthe polymer chain length distribution. Dimensional changes of the resin particles necessitate the use of non-standard mathematical tools for dynamic simulations. A transformed coordinate system, where the mass of the polymer was used as a spatial variable, was applied when simulating the chromatographic reactor columns as well as the swelling and shrinking kinetics of the resin particles. Shrinking of the particles in a column leads to formation of dead volume on top of the resin bed. In ordinary Eulerian coordinates, this results in a moving discontinuity that in turn causes numerical difficulties in the solution of the PDE system. The motion of the discontinuity was eliminated by spanning two calculation grids in the column that overlapped at the top of the resin bed. The reactive and non-reactive phase equilibrium data were correlated with a model derived from thethermodynamics of polymer solution and gels. The thermodynamic approach used inthis work is best suited at high degrees of swelling because the polymer matrixmay be in the glassy state when the extent of swelling is low.

Stabilization of the ionic form of weak acid cation exchange resins

Weak acid cation exchange (WAC) resins are used in the chromatographic separation of betaine from vinasse, a by-product of sugar industry. The ionic form of the resin determines the elution time of betaine. When a WAC-resin is in hydrogen form, the retention time of betaine is the longest and betaine elutes as the last component of vi-nasse from the chromatographic column. If the feed solution contains salts and its pH is not acidic enough to keep the resin undissociated, the ionic form of the hydrogen form resin starts to alter. Vinasse contains salts and its pH is around 5, it also contains weak acids. To keep the metal ion content (Na/H ratio) of the resin low enough to ensure successful separation of betaine, acid has to be added to either eluent (water) or vinasse. The aim of the present work was to examine by laboratory experiments which option requires less acid. Also the retention mechanism of betaine was investigated by measuring retention volumes of acetic acid and choline in different Na/H ratios of the resin. It was found that the resulting ionic form of the resin is the same regardless of whether the regeneration acid is added to the eluent or the feed solution (vinasse). Be-sides the salt concentration and the pH of vinasse, also the concentration of weak acids in the feed affects the resulting ionic form of the resin. The more buffering capacity vinasse has, the more acid is required to keep the ionic form of the resin desired. Vinasse was found to be quite strong buffer solution, which means relatively high amounts of acid are required to prevent the Na/H ratio from increasing too much. It is known that the retention volume of betaine decreases significantly, when the Na/H ratio increases. This is assumed to occur, because the amount of hydrogen bonds between the carboxylic groups of betaine and the resin decreases. Same behavior was not found with acetic acid. Choline has the same molecular structure as betaine, but instead of carboxylic group it has hydroxide group. The retention volume of choline increased as the Na/H ratio of the resin increased, because of the ion exchange reaction between choline cation and dissociated carboxylic group of the resin. Since the retention behavior of choline on the resin is opposite to the behavior of be-taine, the strong affinity of betaine towards hydrogen form WAC-resin has to be based on its carboxylic group. It is probable that the quaternary ammonium groups also affect the behavior of the carboxylic groups of betaine, causing them to form hydrogen bonds with the carboxylic groups of the resin.

Dental Health in Primary Teeth after Prevention of Mother-Child Transmission of Mutans Streptococci. A Historical Cohort Study on Restorative Visits and Maternal Prevention Costs

Mutansstreptokokkitartunnan ehkäisemisen pitkäaikaisvaikutukset maitohampaiden terveyteen. Kohorttitutkimus korjaavan hoidon määrästä ja kariesehkäisyn kustannuksista. Tutkimuksen tarkoituksena oli selvittää varhaisen mutansstreptokokki (MS)-kolonisaation ehkäisyn pitkäaikaisvaikutuksia korkean kariesriskin omaavien lasten maitohampaistossa sekä tarkastella MS-tartunnan estämisen kustannuksia. Tiedot lasten hampaiden terveydestä ja hammashoitotoimenpiteistä syntymästä 10-vuotiaaksi sekä äiteihin kohdistuneen kariesehkäisyn kustannuksista kerättiin Ylivieskan terveyskeskuksen asiakirjoista. Tutkimuksessa oli mukana yhteensä 507 lasta, heistä 148 oli osallistunut aikaisempaan Ylivieskan äiti-lapsitutkimukseen, jossa verrattiin äitien käyttämän ksylitolipurukumin ja äidille tehtyjen fluori- tai klooriheksidiinilakkausten vaikutusta pikkulasten hampaiden terveyteen. Maitohammaskariesta esiintyi 10-vuotiaaksi asti merkitsevästi vähemmän lapsilla, jotka eivät olleet saaneet MS-tartuntaa alle 2-vuotiaana, heidän maitohampaansa säilyivät 3,4 vuotta kauemmin täysin ehjinä (p<0.001) ja he tarvitsivat vähemmän maitohampaiden korjaavaa hoitoa (p=0.005) kuin lapset, joiden hampaisto oli kolonisoitunut MS-bakteerilla jo 2-vuotiaana. Koska ksylitoliryhmän lasten MS-kolonisaatio oli vähäisintä, heidän maitohampaissaan oli vähemmän kariesta ja korjaavan hoidon tarvetta kuin kahden muun korkeariskisen ryhmän lapsilla. Äitien käyttämän ksylitolipurukumin kustannukset olivat yhteensä 116 euroa ja lapsen maitohampaiden säilyminen täysin ehjinä vuoden pidempään maksoi 37 euroa. Kun MS-tartunta oli saatu estettyä, korkean kariesriskin omaavien lasten hampaiden terveys oli samalla tasolla kuin keskimäärin koko ikäkohortilla. Lapsen maitohampaat säilyvät terveinä pidempään ja korjaavan hoidon tarve vähenee, kun MS-kolonisaatio alle 2-vuotiaana saadaan estettyä. Lapsen MS-kolonisaatio vähenee merkitsevästi, kun äiti käyttää ksylitolipurukumia lapsen ollessa 0-2 vuoden ikäinen, siten pikkulapsen äidin säännöllinen ksylitolipurukumin käyttö saattaa olla julkisen tereydenhuollon kannalta tarkoituksenmukainenterveyttä edistävä menetelmä.

Rigid Rod Polymer Fillers in Acrylic Denture and Dental Adhesive Resin Systems

Polymeric materials have been used in dental applications for decades. Adhesion of polymeric materials to each other and to the tooth substrate is essential to their successful use. The aim of this series of studies was two-folded. First, to improve adhesion of poly(paraphenylene) based rigid rod polymer (RRP) to other dental polymers, and secondly, to evaluate the usability of a new dentin primer system based on RRP fillers. Poly(paraphenylene) based RRP would be a tempting material for dental applications because of its good mechanical properties. To be used in dental applications, reliable adhesion between RRP and other dental polymers is required. In this series of studies, the adhesion of RRP to denture base polymer and the mechanical properties of RRP-denture base polymer-material combination were evaluated. Also adhesion of BisGMA-TEGDMA-resin to RRP was determined. Different surface treatments were tested to improve the adhesion of BisGMA-TEGDMA-resin to RRP. Results were based on three-point bending testing, Vickers surface hardness test and scanning electron microscope analysis (SEM), which showed that no reliable adhesion between RRP and denture base polymer was formed. Addition of RRP filler to denture base polymer increased surface hardness and flexural modulus but flexural strength decreased. Results from the shear bond strength test and SEM revealed that adhesion between resin and RRP was possible to improve by surface treatment with dichloromethane (DCM) based primer and a new kind of adhesive surface can be designed. The current dentin bonding agents have good immediate bond strength, but in long term the bond strength may decrease due to the detrimental effect of water and perhaps by matrix metalloproteinases. This leads to problems in longevity of restorations. Current bonding agents use organic monomers. In this series of studies, RRP filled dentin primer was tested in order to decrease the water sorption of the monomer system of the primers. The properties of new dentin primer system were evaluated in vitro by comparing it to commercial etch and rinse adhesive system. The results from the contact angle measurements and SEM showed that experimental primer with RRP reinforcement provided similar resin infiltration to dentin collagen and formed the resin-dentin interface as the control primer. Microtensile bond strength test and SEM revealed that in short term water storing, RRP increased bond strength and primer with BMEP-monomer (bis[2-(methacryloyloxy)-ethyl]phosphate) and high solvent concentration provided comparable bonding properties to the commercial control primers. In long term water storing, the high solvent-monomer concentration of the experimental primers decreased bond strength. However, in low solvent-monomer concentration groups, the long-term water storing did not decrease the bond strength despite the existence of hydrophilic monomers which were used in the system. These studies demonstrated that new dentin primer system reached the mechanical properties of current traditional etch and rinse adhesive system in short time water storing. Improved properties can be achieved by further modifications of the monomer system. Studies of the adhesion of RRP to other polymers suggest that adhesion between RRP and other dental polymers is possible to obtain by certain surface treatments.

The Influence of Certain Processing Factors on the Durability of Yttrium Stabilized Zirconia Used As Dental Biomaterial

In dentistry, yttrium partially stabilized zirconia (ZrO2) has become one of the most attractive ceramic materials for prosthetic applications. The aim of this series of studies was to evaluate whether certain treatments used in the manufacturing process, such as sintering time, color shading or heat treatment of zirconia affect the material properties. Another aim was to evaluate the load-bearing capacity and marginal fit of manually copy-milled custom-made versus prefabricated commercially available zirconia implant abutments. Mechanical properties such as flexural strength and surface microhardness were determined for green-stage milled and sintered yttrium partially stabilized zirconia after different sintering time, coloring process and heat treatments. Scanning electron microscope (SEM) was used for analyzing the possible changes in surface structure of zirconia material after reduced sintering time, coloring and heat treatments. Possible phase change from the tetragonal to the monoclinic phase was evaluated by X-ray diffraction analysis (XRD). The load-bearing capacity of different implant abutments was measured and the fit between abutment and implant replica was examined with SEM. The results of these studies showed that the shorter sintering time or the thermocycling did not affect the strength or surface microhardness of zirconia. Coloring of zirconia decreased strength compared to un-colored control zirconia, and some of the colored zirconia specimens also showed a decrease in surface microhardness. Coloring also affected the dimensions of zirconia. Significantly decreased shrinkage was found for colored zirconia specimens during sintering. Heat treatment of zirconia did not seem to affect materials’ mechanical properties but when a thin coating of wash and glaze porcelain was fired on the tensile side of the disc the flexural strength decreased significantly. Furthermore, it was found that thermocycling increased the monoclinic phase on the surface of the zirconia. Color shading or heat treatment did not seem to affect phase transformation but small monoclinic peaks were detected on the surface of the heat treated specimens with a thin coating of wash and glaze porcelain on the opposite side. Custom-made zirconia abutments showed comparable load-bearing capacity to the prefabricated commercially available zirconia abutments. However, the fit of the custom-made abutments was less satisfactory than that of the commercially available abutments. These studies suggest that zirconia is a durable material and other treatments than color shading used in the manufacturing process of zirconia bulk material does not affect the material’s strength. The decrease in strength and dimensional changes after color shading needs to be taken into account when fabricating zirconia substructures for fixed dental prostheses. Manually copy-milled custom-made abutments have acceptable load-bearing capacity but the marginal accuracy has to be evaluated carefully.

Virtual Professional Network as a Value Creator in the Dental Business

The research of virtual professional networks has been enormous but the lack of research in the dental field was obvious. This study focuses on those uses and gratifications, and motives of participants that a virtual pro-fessional network should fulfil. The aim of this study is to understand the factors behind the successful virtual professional network, and motives of participants that support a particular business network’s building up for contributing its further success. In this study the focus is on particular mo-tives, needs and benefits of participants that are significant for the net-work’s further development. The study will explore relevant scientific research and theory that is char-acteristic in networking, and theories of user’s needs and motives. Empiri-cal data was collected from dental professionals by net based question-naire that was sent by e-mail. Data analysis was done by quantitative fac-tor analysis. The findings of this study were obvious that virtual knowledge of implantology is inadequate and knowledge is rather difficult to find in the Internet. Sharing of virtual knowledge, net-learning and communication were seen to improve the quality of impolantological professionalism and also the development of these areas was experienced essential. On the grounds of this study a host of a virtual professional network can focus on those aspects that serve the users at best, can develop professionalism in implantology and can profit in its own business operations.

Carbohydrate intake in children - associations with dietary intakes, growth, serum lipids,and dental health. The STRIP Project

This study is part of the STRIP study, which is a long-term, randomized controlled trial, designed to decrease the exposure of children in the intervention group (n=540) to known risk factors of atherosclerosis. The main focus of the intervention was the quality of dietary fat. The control group (n=522) did not receive any individualized counselling. Food consumption was evaluated with food records, and blood samples were drawn and growth was measured regularly for all participating children from 13 months to 9 years. A subsample of 66 children participated in a dental health survey. The number of studies on children’s carbohydrate intake, especially fibre intake, is insufficient. The current international recommendations for fibre intake in children are based on average assumptions and data extrapolated from intakes in adults and intake recommendations for adults. Finnish nutrition recommendations lack strict recommendations for dietary fibre in children. Due to fibre’s high bulk volume, excessive dietary fibre is considered to decrease energy density and hence it may have an adverse effect on growth. If fats are reduced from the diet, the low-fat diet may become high in sucrose. Therefore, especially in the STRIP study, it is important to determine the use of fibre and sucrose in children and possible associations with growth and nutrition as well as dental health. The results of the present study indicate that a high fibre intake does not displace energy or disturb growth in children and that children with high fibre intake have better quality of diet than those with low fibre intake. Additionally, dietary fibre intake associated inversely with serum cholesterol concentration. Other carbohydrates also affected serum lipid levels as well, since total carbohydrates, sucrose, and fructose increased serum triglyceride concentration. Total carbohydrate intake reduced HDL cholesterol concentration only in children with apoE3 or apoE4 phenotype. Over the period from the 1970s to the 1990s the dental health of children in Finland has substantially improved despite an increase in sucrose intake. The improvement was thought to be due to improved dental hygiene and the use of fluorine. However, during the past twenty years improvement in dental health has stopped. The present study showed that high long-term sugar intake increases risk of caries in children. High intake of sugar had also negative effects on the diet of children, because it worsens dietary quality by displacing essential nutrients. Furthermore, the quality of dietary fat was worse in children with high sucrose intake. In this study the children’s high sucrose intake was not associated with overweight, but interestingly, it associated inversely with growth.

Dental Health in Preschool and Schoolchildren in Relation to Dental Fear and Some Fear-Related Factors, and the Outcome of a Caries Prevention Program in Offspring of Fearful Mothers

Dental caries and dental fear and anxiety (DFA) are common interrelated problems but so far little is known about these problems in Estonia. The aim was to study dental health in relation to DFA, some fear-related factors, and to study the effect of a caries prevention program in children of fearful mothers. Dental health and DFA were assessed in two Estonian [2-4-year-olds (n=472) and 8-10-year-olds (n=344)], and the effect of some medical conditions on DFA in one Finnish child group [3-year-olds (n=148)]. 120 mother-child-pairs participated in the xylitol-based prevention program. Dental health was examined using the WHO or the ICDAS criteria and expressed as dmft/DMFT-indices. The modified children’s fear survey schedule dental subscale (MCFSS-DS) was used to assess DFA of schoolchildren, one single question to assess parental DFA, and the Corah’s dental anxiety scale (DAS) to assess DFA of mothers in the prevention study. Dentine caries was diagnosed in 42% of the 2-4-year-old and in 93% of the 8-10-year-old Estonian children. DFA of 8-10-year-olds (17%) was associated with experience of dental treatment, and maternal and paternal DFA. Dental apprehension at 9 years of age was associated with frequent exposure to invasive medical care. The xylitol-based prevention was successful irrespective of poor dental hygiene habits and maternal severe DFA. In conclusion, experience of operative dental treatment and DFA of Estonian children were closely associated. Invasive medical care and parental DFA were also linked to children’s DFA. Habitual use of xylitol by mothers was effective in preventing caries even in children of severely fearful mothers.

Dental fear in adolescents' transition to early adulthood

The aims of the study were to assess the validity of a clinical dental fear question (Short Dental Fear Question, SDFQ) and an instrument measuring interaction between adolescents and dental staff (Patient Dental Staff Interaction Questionnaire, PDSIQ). Also, adolescents’ subjective perception of interaction with dental staff, the association with adolescents’ dental fear and sense of coherence as well as a multi-professional small-group intervention model for decreasing high dental fear were assessed. The study sample comprised Finnish adolescents in transition to early adulthood, aged 18–26 years (n = 777, n = 773, n = 5), except for a sample of 15-year-old adolescents (n = 27). Dental fear, sense of coherence (SOC) and the adolescents’ perceived interaction with dental staff were assessed with questionnaires. The principles of fear treatment such as gradual exposure, relaxation, encouragement and cornerstones of the reteaming method based on a solution-focused framework to maintain motivation and peer support were used to decrease fear in the intervention study. The SDFQ was found to be a valid dental fear instrument and the PDSIQ a valid interaction instrument with five factors of interaction retrieved: ‘kind atmosphere and mutual communication’, ‘roughness’, ‘insecurity’, ‘trust and safety’, and ‘shame and guilt’. Highly fearful young adults more often perceived their interaction with dental staff as negative, more often felt insecure and had a weaker sense of coherence compared to their peers with no to moderate dental fear. The results of the intervention study showed that young adults’ high dental fear decreased and their commitment to dental treatment increased. The SDFQ is clinically feasible and informative instrument in measuring dental fear. Knowledge of the level of fear enables dental staff to better consider an adolescent’s fear. Dental staff should be aware that a supportive interaction style, creating trust and safety, is especially beneficial for highly dentally fearful young adults. A weak SOC may affect young adults’ high dental fear in that they would not have enough tools to manage their fear. A multi-professional small therapeutic group seems to increase fearful young adults’ resources for confronting dental treatment.

Evaluation of novel programs in health counseling – their effectiveness in the oral health of young children, and their acceptance by parents and professionals in public dental service.

Aim and design: To evaluate family-based health counseling for young children, and to study the significance of adding parental self-care or the training of professionals to the programs. The effectiveness and acceptability of the programs were evaluated by comparing two new programs with an earlier one. Subjects and methods: The study was carried out in Vantaa, which was divided into three study areas. The subjects consisted of children born in 2008, particularly fi rstborn children, while children born in 2006 formed the historical control. The fi rst of the new programs emphasized oral hygiene and use of fl uoride, and the second program focused on proper diet and use of xylitol. The main outcome measure was mutansstreptococci (MS) in the dental biofi lm of two-year-olds, and the opinions of parents and dental professionals were evaluated using questionnaires. Results: The programs found wide acceptance among dental professionals. There were no group-related differences found in the MS scores of the two-year-olds. However, all groups combined, father’s advanced level of education and child’s proper use of xylitol were associated with negative MS scores. In the opinion of parents, the oral healthcare guidance at least somewhat met their expectations. Conclusions: The present fi ndings suggest that providing training and support for professionals in health education is important. The addition of parental self-care to supplement programs aimed at young children does not improve the program, although it may improve parental readiness to change their own health habits. Counseling for families might be best carried out through a routine patient-centered program.