Modified nano- and microcellulose based adsorption materials in water treatment

In recent decades, industrial activity growth and increasing water usage worldwide have led to the release of various pollutants, such as toxic heavy metals and nutrients, into the aquatic environment. Modified nanocellulose and microcellulose-based adsorption materials have the potential to remove these contaminants from aqueous solutions. The present research consisted of the preparation of five different nano/microcellulose-based adsorbents, their characterization, the study of adsorption kinetics and isotherms, the determination of adsorption mechanisms, and an evaluation of adsorbents’ regeneration properties. The same well known reactions and modification methods that were used for modifying conventional cellulose also worked for microfibrillated cellulose (MFC). The use of succinic anhydride modified mercerized nanocellulose, and aminosilane and hydroxyapatite modified nanostructured MFC for the removal of heavy metals from aqueous solutions exhibited promising results. Aminosilane, epoxy and hydroxyapatite modified MFC could be used as a promising alternative for H2S removal from aqueous solutions. In addition, new knowledge about the adsorption properties of carbonated hydroxyapatite modified MFC as multifunctional adsorbent for the removal of both cations and anions ions from water was obtained. The maghemite nanoparticles (Fe3O4) modified MFC was found to be a highly promising adsorbent for the removal of As(V) from aqueous solutions due to its magnetic properties, high surface area, and high adsorption capacity . The maximum removal efficiencies of each adsorbent were studied in batch mode. The results of adsorption kinetics indicated very fast removal rates for all the studied pollutants. Modeling of adsorption isotherms and adsorption kinetics using various theoretical models provided information about the adsorbent’s surface properties and the adsorption mechanisms. This knowledge is important for instance, in designing water treatment units/plants. Furthermore, the correspondence between the theory behind the model and properties of the adsorbent as well as adsorption mechanisms were also discussed. On the whole, both the experimental results and theoretical considerations supported the potential applicability of the studied nano/microcellulose-based adsorbents in water treatment applications.

Assessing the Environmental Value of Water Treatment Solutions in the Mining Industry

Environmental accountability has become a major source of competitive advantage for industrial companies, because customers consider it as relevant buying criterion. However, in order to leverage their environmental responsibility, industrial suppliers have to be able to demonstrate the environmental value of their products and services, which is also the aim of Kemira, a global water chemistry company considered in this study. The aim of this thesis is to develop a tool which Kemira can use to assess the environmental value of their solutions for the customer companies in mining industry. This study answers to questions on what kinds of methods to assess environmental impacts exist, and what kind of tool could be used to assess the environmental value of Kemira’s water treatment solutions. The environmental impacts of mining activities vary greatly between different mines. Generally the major impacts include the water related issues and wastes. Energy consumption is also a significant environmental aspect. Water related issues include water consumption and impacts in water quality. There are several methods to assess environmental impacts, for example life cycle assessment, eco-efficiency tools, footprint calculations and process simulation. In addition the corresponding financial value may be estimated utilizing monetary assessment methods. Some of the industrial companies considered in the analysis of industry best practices use environmental and sustainability assessments. Based on the theoretical research and conducted interviews, an Excel based tool utilizing reference data on previous customer cases and customer specific test results was considered to be most suitable to assess the environmental value of Kemira’s solutions. The tool can be used to demonstrate the functionality of Kemira’s solutions in customers’ processes, their impacts in other process parameters and their environmental and financial aspects. In the future, the tool may be applied to fit also Kemira’s other segments, not only mining industry.

Developing Service-based Solutions for Water Treatment in Finnish Mining Industry

The aim of this master’s thesis is to analyze the mining industry customers' current and future needs for the water treatment services and discover new business development opportunities in the context of mine water treatment. In addition, the study focuses on specifying service offerings needed and evaluate suitable revenue generation models for them. The main research question of the study is: What kind of service needs related to water treatment can be identified in the Finnish mining industry? The literature examined in the study focused on industrial service classification and new service development process as well as the revenue generation of services. A qualitative research approach employing a case study method was chosen for the study. The present study uses customer and expert interviews as primary data source, complemented by archival data. The primary data was gathered by organizing total of 13 interviews, and the interviews were analyzed by using qualitative content analysis. The abductive-logic was chosen as the way of conducting scientific reasoning in this study. As a result, new service proposals were developed for Finnish mine industry suppliers. The main areas of development were on asset efficiency services and process support services. The service needs were strongly associated with suppliers’ know-how of water treatment process optimization, cost-effectiveness as well as on alternative technologies. The study provides an insight for managers that wish to pursue a water treatment services as a part of their business offering.

Titanium dioxide based nanomaterials for photocatalytic water treatment

Water treatment using photocatalysis has gained extensive attention in recent years. Photocatalysis is promising technology from green chemistry point of view. The most widely studied and used photocatalyst for decomposition of pollutants in water under ultraviolet irradiation is TiO2 because it is not toxic, relatively cheap and highly active in various reactions. Within this thesis unmodified and modified TiO2 materials (powders and thin films) were prepared. Physico-chemical properties of photocatalytic materials were characterized with UV-visible spectroscopy, scanning electron microscopy (SEM), transmission electron microscopy (TEM), X-ray photoelectron spectrometry (XPS), inductively coupled plasma optical emission spectroscopy (ICP-OES), ellipsometry, time-of-flight secondary ion mass spectrometry (ToF-SIMS), Raman spectroscopy, goniometry, diffuse reflectance measurements, thermogravimetric analysis (TGA) and nitrogen adsorption/desorption. Photocatalytic activity of prepared samples in aqueous environment was tested using model compounds such as phenol, formic acid and metazachlor. Also purification of real pulp and paper wastewater effluent was studied. Concentration of chosen pollutants was measured with high pressure liquid chromatography (HPLC). Mineralization and oxidation of organic contaminants were monitored with total organic carbon (TOC) and chemical oxygen demand (COD) analysis. Titanium dioxide powders prepared via sol-gel method and doped with dysprosium and praseodymium were photocatalytically active for decomposition of metazachlor. The highest degradation rate of metazachlor was observed when Pr-TiO2 treated at 450ºC (8h) was used. The photocatalytic LED-based treatment of wastewater effluent from plywood mill using commercially available TiO2 was demonstrated to be promising post-treatment method (72% of COD and 60% of TOC was decreased after 60 min of irradiation). The TiO2 coatings prepared by atomic layer deposition technique on aluminium foam were photocatalytically active for degradation of formic and phenol, however suppression of activity was observed. Photocatalytic activity of TiO2/SiO2 films doped with gold bipyramid-like nanoparticles was about two times higher than reference, which was not the case when gold nanospheres were used.

International Advanced Water Technologies Centre, IAWTC/LADEC and LUT 2013 : Questionnaire Responses from Russian Drinking Water and Wastewater Treatment Plants

In this report, information is published concerning Russian water and wastewater treatment plants. The information is based on a questionnaire sent to 70 water and wastewater treatment plants in 2012-2013. The questionnaire was prepared by the International Advanced Water Technologies Centre (IAWTC) and Lahti Development Company (LADEC). The questions dealt with an assessment of the present state, the need for changes, renovation, investments, and how to improve the efficiency of the operation by training and investments. A significant need to renew the old pipelines, constructions, and processes was clearly evident. The aggregated answers can be utilized in Russia as internal benchmarking in order to arrange training and plant visits, which were requested in many of the answers. Sharing this open report with the respondents can aid networking and awareness of HELCOM requirements which relate to waste water treatment plants discharging their waste water directly or indirectly into the Baltic Sea. The aim of this report is to provide information for Finnish small and medium size companies (SMEs) as regards possible water related exportation to different parts of Russia.

Tertiary treatment of pulp and paper mill effluents

Työn tavoitteena oli selvittää mitä käsittelyvaihtoehtoja on olemassa jäteveden puhdistamon tertiäärikäsittelyyn ja miten suuri tarve paperi- ja selluteollisuuden prosessivesien puhdistukseen on. Tarkoituksena oli saada käsitys koko tertiäärikäsittelystä eri näkökulmista. Lopuksi läpikäytiin tertiäärikäsittelymenetelmiä ja etsittiin mahdollisia uusia menetelmiä, joita voitaisiin käyttää jäteveden tertiääripuhdistukseen. Ensimmäisenä työssä on perehdytty jäteveden koostumukseen paperi- ja selluteollisuudessa ja puhdistukseen ilmastetulla aktiivilietemenetelmällä, jotta tertiäärikäsittely ymmärrettäisiin konseptina paremmin. Lisäksi työssä selvitettiin tertiäärikäsittelyn tarvetta ja vaihtoehtoja sen käyttämättä jättämiselle teollisuuden ja muun ympäristöä vahingoittavan toiminnan ympäristönäkökohdat huomioonottaen. Lyhyiden menetelmäesitysten jälkeen kiteytetään tertiäärikäsittelyn ympäristönäkökohdatja vaihtoehdot sen käytölle yhteenvetona, jossa otetaan huomioon myös viranomaisten, yrityksen ja BAT referenssien sisältämä tieto tertiäärikäsittelystä. Työn kokeellinen osa sisältää erään tertiäärikäsittelysovelluksenrakentamisen, koekäytön ja laboratorioanalyysien yhteenvedon. Lisäksi menetelmää verrataan kustannus-tehokkuudeltaan vastaavien menetelmien kanssa. Tarkoituksena oli löytää jäteveden tertiäärikäsittelyyn sopiva laitteisto, jonka toimintaanei sisältyisi kemikaalien annostelua ja sitä käytettäisiin lähinnä jätevedenpuhdistamon ongelmatilanteiden väliaikaiseksi ratkaisuksi. Mahdollisesti se voisi toimia myös jatkuvatoimisesti veden kirkastuksessa. Diplomityössä rakennettu laitteisto, jota käytettiin myös pilot koeajoissa, ei ollut paras mahdollinen laitteisto tertiäärikäsittelyn toteuttamiseksi paperi- ja selluteollisuudessa, mutta kilpailukykyinen muiden laitteistojen kanssa. Laitteiston toimintaperiaate on kuitenkin käyttökelpoinen tietyin varauksin ja sitä voidaan käyttää vedenpuhdistamiseen.

Wet Oxidation of Concentrated Wastewaters: Process Combination and Reaction Kinetic Modeling

The accumulation of aqueous pollutants is becoming a global problem. The search for suitable methods and/or combinations of water treatment processes is a task that can slow down and stop the process of water pollution. In this work, the method of wet oxidation was considered as an appropriate technique for the elimination of the impurities present in paper mill process waters. It has been shown that, when combined with traditional wastewater treatment processes, wet oxidation offers many advantages. The combination of coagulation and wet oxidation offers a new opportunity for the improvement of the quality of wastewater designated for discharge or recycling. First of all, the utilization of coagulated sludge via wet oxidation provides a conditioning process for the sludge, i.e. dewatering, which is rather difficult to carry out with untreated waste. Secondly, Fe2(SO4)3, which is employed earlier as a coagulant, transforms the conventional wet oxidation process into a catalytic one. The use of coagulation as the post-treatment for wet oxidation can offer the possibility of the brown hue that usually accompanies the partial oxidation to be reduced. As a result, the supernatant is less colored and also contains a rather low amount of Fe ions to beconsidered for recycling inside mills. The thickened part that consists of metal ions is then recycled back to the wet oxidation system. It was also observed that wet oxidation is favorable for the degradation of pitch substances (LWEs) and lignin that are present in the process waters of paper mills. Rather low operating temperatures are needed for wet oxidation in order to destruct LWEs. The oxidation in the alkaline media provides not only the faster elimination of pitch and lignin but also significantly improves the biodegradable characteristics of wastewater that contains lignin and pitch substances. During the course of the kinetic studies, a model, which can predict the enhancements of the biodegradability of wastewater, was elaborated. The model includes lumped concentrations suchas the chemical oxygen demand and biochemical oxygen demand and reflects a generalized reaction network of oxidative transformations. Later developments incorporated a new lump, the immediately available biochemical oxygen demand, which increased the fidelity of the predictions made by the model. Since changes in biodegradability occur simultaneously with the destruction of LWEs, an attempt was made to combine these two facts for modeling purposes.

Antibioottien poisto vedestä adsorptiolla

Antibiootit ovat yleisessä käytössä olevia lääkeaineita, joilla on kyky hidastaa mikrobien kasvua. Osa lääkeaineesta poistuu elimistöstä muuntumattomana. Koska tavanomainen jäteveden käsittelyprosessi ei riitä poistamaan antibiootteja jätevedestä, ne päätyvät vesistöihin, joissa ne häiritsevät ekosysteemiä ja voivat aiheuttaa vastustuskykyisten bakteerikantojen muodostumisen. Antibiootit voitaisiin poistaa vedestä adsorptiolla. Työssä on esitelty antibioottien adsorptiomekanismeja, vedenkäsittelyssä käytettäviä adsorptioprosesseja ja adsorbentteja, jotka soveltuvat antibioottien erottamiseen vedestä. Lisäksi tarkastellaan yleisesti adsorption kinetiikkaa ja termodynamiikkaa sekä mallinnetaan panoskokeiden tulosten perusteella jatkuvatoimisen adsorptiokolonnin toimintaa.

Treatment of oily wastewater by ultrafiltration: The effect of different operating and solution conditions

In many industries, such as petroleum production, and the petrochemical, metal, food and cosmetics industries, wastewaters containing an emulsion of oil in water are often produced. The emulsions consist of water (up to 90%), oils (mineral, animal, vegetable and synthetic), surfactants and other contaminates. In view of its toxic nature and its deleterious effects on the surrounding environment (soil, water) such wastewater needs to be treated before release into natural water ways. Membrane-based processes have successfully been applied in industrial applications and are considered as possible candidates for the treatment of oily wastewaters. Easy operation, lower cost, and in some cases, the ability to reduce contaminants below existing pollution limits are the main advantages of these systems. The main drawback of membranes is flux decline due tofouling and concentration polarisation. The complexity of oil-containing systems demands complementary studies on issues related to the mitigation of fouling and concentration polarisation in membranebased ultrafiltration. In this thesis the effect of different operating conditions (factors) on ultrafiltration of oily water is studied. Important factors are normally correlated and, therefore, their effect should be studied simultaneously. This work uses a novel approach to study different operating conditions, like pressure, flow velocity, and temperature, and solution properties, like oil concentration (cutting oil, diesel, kerosene), pH, and salt concentration (CaCl2 and NaCl)) in the ultrafiltration of oily water, simultaneously and in a systematic way using an experimental design approach. A hypothesis is developed to describe the interaction between the oil drops, salt and the membrane surface. The optimum conditions for ultrafiltration and the contribution of each factor in the ultrafiltration of oily water are evaluated. It is found that the effect on permeate flux of the various factors studied strongly depended on the type of oil, the type of membrane and the amount of salts. The thesis demonstrates that a system containing oil is very complex, and that fouling and flux decline can be observed even at very low pressures. This means that only the weak form of the critical flux exists for such systems. The cleaning of the fouled membranes and the influence of different parameters (flow velocity, temperature, time, pressure, and chemical concentration (SDS, NaOH)) were evaluated in this study. It was observed that fouling, and consequently cleaning, behaved differently for the studied membranes. Of the membranes studied, the membrane with the lowest propensity for fouling and the most easily cleaned was the regenerated cellulose membrane (C100H). In order to get more information about the interaction between the membrane and the components of the emulsion, a streaming potential study was performed on the membrane. The experiments were carried out at different pH and oil concentration. It was seen that oily water changed the surface charge of the membrane significantly. The surface charge and the streaming potential during different stages of filtration were measured and analysed being a new method for fouling of oil in this thesis. The surface charge varied in different stages of filtration. It was found that the surface charge of a cleaned membrane was not the same as initially; however, the permeability was equal to that of a virgin membrane. The effect of filtration mode was studied by performing the filtration in both cross-flow and deadend mode. The effect of salt on performance was considered in both studies. It was found that salt decreased the permeate flux even at low concentration. To test the effect of hydrophilicity change, the commercial membranes used in this thesis were modified by grafting (PNIPAAm) on their surfaces. A new technique (corona treatment) was used for this modification. The effect of modification on permeate flux and retention was evaluated. The modified membranes changed their pore size around 33oC resulting in different retention and permeability. The obtained results in this thesis can be applied to optimise the operation of a membrane plant under normal or shock conditions or to modify the process such that it becomes more efficient or effective.

Lannoitetehtaan prosessivesien käsittelyvaihtoehtojen soveltuvuuden arviointi

Phosphorus and nitrogen cause eutrophication of water bodies, causing severe damage to the ecosystem. Eutrophication of the waters causes oxygen depletion, which in turn increases fish mortality, releasing toxins in waters. The released toxins can cause damage to animals and humans, which is the reason in many countries to set emission limits for waste water. Nutrients exist naturally, but due to human activities there is high nutrient leaching to water bodies. Human activity is one of the main reasons to the eutrophication. The aim of this thesis was to estimate the suitability of different water treatment options for Yara Finland’s fertilizer plant’s process waters in Siilinjärvi. The fertilizer plant process waters are high concentrate and especially nitrogen concentrations are high, which bring challenge to the treatment. At the theoretical part was investigated conventional and as well advanced wastewater treatment methods like reverse osmosis, adsorption and ion exchange. Beside different treatment methods corporate environmental requirements, responsibility and strategies were researched. At the empirical part of the thesis the goal was to find out possibil-ities to intensify the efficiency of purification at lamella clarifier with chemical precipitation. In addition possibility to use already existing chemical purifying plant for process waters was estimated. As a result of the research Yara has a possibility to intensify lamella clarifier’s action by addi-tion of calcium hydroxide and thus to obtain the phosphorus and fluorine to precipitate out of the water. But in practice this would be too expensive. It is possible to eliminate nitrogen compounds by adsorption or ammonia stripping, both methods requires additional testing. It is possible to process waters in chemical purifying plant, if ammonium nitrogen has been reduced before. Reverse osmosis is possible to exploit for the phosphoric acid plant’s waters.

Electrocoagulation in the treatment of industrial waters and wastewaters

Chemical coagulation is commonly used in raw water and wastewater treatment plants for the destabilisation of pollutants so that they can be removed in the subsequent separation processes. The most commonly used coagulation chemicals are aluminium and iron metal salts. Electrocoagulation technology has also been proposed for the treatment of raw waters and wastewaters. With this technology, metal cations are produced on the electrodes via electrolysis and these cations form various hydroxides in the water depending on the water pH. In addition to this main reaction, several side reactions, such as hydrogen bubble formation and the reduction of metals on cathodes, also take place in the cell. In this research, the applications of electrocoagulation were investigated in raw water treatment and wastewater applications. The surface water used in this research contained high concentrations of natural organic matter (NOM). The effect of the main parameters – current density, initial pH, electric charge per volume, temperature and electrolysis cell construction – on NOM removal were investigated. In the wastewater treatment studies, the removal of malodorous sulphides and toxic compounds from the wastewaters and debarking effluents were studied. Also, the main parameters of the treatment, such as initial pH and current density, were investigated. Aluminium electrodes were selected for the raw water treatment, whereas wastewaters and debarking effluent were treated with iron electrodes. According to results of this study, aluminium is more suitable electrode material for electrocoagulation applications because it produces Al(III) species. Metal ions and hydroxides produced by iron electrodes are less effective in the destabilisation of pollutants because iron electrodes produce more soluble and less charged Fe(II) species. However, Fe(II) can be effective in some special applications, such as sulphide removal. The resulting metal concentration is the main parameter affecting destabilisation of pollutants. Current density, treatment time, temperature and electrolysis cell construction affect the dissolution of electrodes and hence also the removal of pollutants. However, it seems that these parameters have minimal significance in the destabilization of the pollutants besides this effect (in the studied range of parameters). Initial pH and final pH have an effect on the dissolution of electrodes, but they also define what aluminium or iron species are formed in the solution and have an effect on the ζ-potential of all charged species in the solution. According to the results of this study, destabilisation mechanisms of pollutants by electrocoagulation and chemical coagulation are similar. Optimum DOC removal and low residual aluminium can be obtained simultaneously with electrocoagulation, which may be a significant benefit of electrocoagulation in surface water treatment compared to chemical coagulation. Surface water treatment with electrocoagulation can produce high quality water, which could be used as potable water or fresh water for industrial applications. In wastewater treatment applications, electrocoagulation can be used to precipitate malodorous sulphides to prevent their release into air. Technology seems to be able to remove some toxic pollutants from wastewater and could be used as pretreatment prior to treatment at a biological wastewater treatment plant. However, a thorough economic and ecological comparison of chemical coagulation and electrocoagulation is recommended, because these methods seem to be similar in pollutant destabilisation mechanisms, metal consumption and removal efficiency in most applications.

Electro-Oxidation Treatment of Pulp and Paper Mill Circulating Waters and Wastewaters

Interest in water treatment by electrochemical methods has grown in recent years. Electrochemical oxidation has been applied particularly successfully to degrade different organic pollutants and disinfect drinking water. This study summarizes the effectiveness of the electrochemical oxidation technique in inactivating different primary biofilm forming paper mill bacteria as well as sulphide and organic material in pulp and paper mill wastewater in laboratory scale batch experiments. Three different electrodes, borondoped diamond (BDD), mixed metal oxide (MMO) and PbO2, were employed as anodes. The impact on inactivation efficiency of parameters such as current density and initial pH or chloride concentration of synthetic paper machine water was studied. The electrochemical behaviour of the electrodes was investigated by cyclic voltammetry with MMO, BDD and PbO2 electrodes in synthetic paper mill water as also with MMO and stainless steel electrodes with biocides. Some suggestions on the formation of different oxidants and oxidation mechanisms were also presented during the treatment. Aerobic paper mill bacteria species (Deinococcus geothermalis, Pseudoxanthomonas taiwanensis and Meiothermus silvanus) were inactivated effectively (>2 log) at MMO electrodes by current density of 50 mA/cm2 and the time taken three minutes. Increasing current density and initial chloride concentration of paper mill water increased the inactivation rate of Deinococcus geothermalis. The inactivation order of different bacteria species was Meiothermus silvanus > Pseudoxanthomonas taiwanensis > Deinococcus geothermalis. It was observed that inactivation was mainly due to the electrochemically generated chlorine/hypochlorite from chloride present in the water and also residual disinfection by chlorine/hypochlorite occurred. In real paper mill effluent treatment sulphide oxidation was effective with all the different initial concentrations (almost 100% reduction, current density 42.9 mA/cm2) and also anaerobic bacteria inactivation was observed (almost 90% reduction by chloride concentration of 164 mg/L and current density of 42.9 mA/cm2 in five minutes). Organic material removal was not as effective when comparing with other tested techniques, probably due to the relatively low treatment times. Cyclic voltammograms in synthetic paper mill water with stainless steel electrode showed that H2O2 could be degraded to radicals during the cathodic runs. This emphasises strong potential of combined electrochemical treatment with this biocide in bacteria inactivation in paper mill environments.

Pulsed corona discharge as an advanced oxidation process for degradation of organic

Advanced oxidation processes (AOPs) have been studied and developed to suffice the effective removal of refractory and toxic compounds in polluted water. The quality and cost of wastewater treatment need improvements, and electric discharge technology has a potential to make a significant difference compared to other established AOPs based on energy efficiency. The generation of active oxidant species such as ozone and hydroxyl radicals by high voltage discharge is a relatively new technology for water treatment. Gas-phase pulsed corona discharge (PCD), where a treated aqueous solution is dispersed between corona-producing electrodes free of the dielectric barriers, was developed as an alternative approach to the problem. The short living radicals and ozone formed in the gas phase and at the gas-liquid interface react with dissolved impurities. PCD equipment has a relatively simple configuration, and with the reactor in an enclosed compartment, it is insensitive towards gas humidity and does not need the gas transport. In this thesis, PCD was used to study and evaluate the energy efficiency for degrading various organic compounds, as well as the chemistry of the oxidation products formed. The experiments investigate the aqueous oxidation of phenol, humic substances, pharmaceutical compounds (paracetamol, ibuprofen, indomethacin, salicylic acids, -estradiol), as well as lignin degradation and transformation to aldehydes. The study aims to establish the influence of initial concentration of the target pollutant, the pulsed discharge parameters, gas phase composition and the pH on the oxidation kinetics and the efficiency. Analytical methods to measure the concentrations of the target compounds and their by-products include HPLC, spectrophotometry, TOC and capillary electrophoresis. The results of the research included in this summary are presented in the attached publications and manuscripts accepted for publication. Pulsed corona discharge proved to be highly effective in oxidizing each of the target compounds, surpassing the closest competitor, conventional ozonation. The increase in oxidation efficiencies for some compounds in oxygen media and at lower pulse repetition frequencies shows a significant role of ozone. The role of the ·OH radicals was established in the surface reactions. The main oxidation products, formation of nitrates, and the lignin transformation were quantified. A compound specific approach is suggested for optimization of the PCD parameters that have the most significant impact on the oxidation energy efficiency because of the different characteristics and responses of the target compound to the oxidants, as well as different admixtures that are present in the wastewater. Further studies in the method’s safety (nitration and nitrosation of organic compounds, nitrite and nitrate formation enhancement) are needed for promoting the method.

Treatment of Fe-containing Acid Mine Waters in Fixed Bed Adsorption Column with Calcite Side-Stone

The acid mining drainage is considered the most significant environmental pollution problem around the world for the extensive formation acidic leachates containing heavy metals. Adsorption is widely used methods in water treatment due to it easy operation and the availability of a wide variety of commercial adsorbent (low cost). The primary goal of this thesis was to investigate the efficiency of neutralizing agents, CaCO3 and CaSiO3, and metal adsorption materials with unmodified limestone from Company Nordkalk Oy. In addition to this, the side materials of limestone mining were tested for iron adsorption from acidic model solution. This study was executed at Lappeenranta University of Technology, Finland. The work utilised fixed-bed adsorption column as the main equipment and large fluidized column. Atomic absorption spectroscopy (AAS) and x-ray diffraction (XRD) was used to determine ferric removal and the composition of material respectively. The results suggest a high potential for the studied materials to be used a low cost adsorbents in acid mine drainage treatment. From the two studied adsorbents, the FS material was more suitable than the Gotland material. Based on the findings, it is recommended that further studies might include detailed analysis of Gotland materials.

Kunnallisen jätevedenkäsittelyn tehostaminen membraanitekniikan avulla – esimerkkinä Savitaipaleen jätevedenpuhdistamo

Työssä tutkittiin mahdollisuutta tehostaa kunnallista jätevedenpuhdistusta membraanitekniikkaa käyttäen. Teoriaosassa perehdyttiin kunnallisen jäteveden omi-naisuuksiin ja perinteiseen puhdistusprosessiin. Tämän lisäksi membraanien yleisiä ominaisuuksia, membraanityyppien kykyä erottaa jäteveden sisältämiä yhdisteitä sekä erilaisia mahdollisuuksia membraanisuodatukselle perinteisen jäteve-denpuhdistusprosessin yhteydessä käytiin läpi. Kokeellisessa osassa keskityttiin Savitaipaleen puhdistamon puhdistetun jäteveden laadun parantamiseen membraanisuodatukseen perustuvalla jälkikäsittely-yksiköllä eli tertiäärisuodatuksella. Erilaisia paineavusteisia membraanitekniikoita (MF, UF, NF ja RO) tutkittiin jäteveden puhdistamiseksi ja erotustehokkuuden vertailemiseksi. Tavoitteena oli löytää tehokas ja käytännössä toimiva tapa poistaa fosforia ja typpeä puhdistetusta jätevedestä. Tasomaisilla membraaneilla tehdyissä suodatuksissa MF-membraanit poistivat tehokkaasti fosforia (97 – 98 %) sekä kiintoainesta (100 %) jätevedestä. RO-membraanit alensivat fosfori- (100 %) ja typpipitoisuutta (90 – 94 %) tehokkaasti, poistaen myös liuenneita orgaanisia yhdisteitä (DOC, 90 – 94 %). Mikrosuodatukseen perustuvilla onttokuitumembraaneilla saavutettiin tehokkaan fosforinpoiston lisäksi tasainen kapasiteetti suodatuksen aikaista puhdistusmene-telmää optimoimalla. Pitoisuusalenemat olivat myös erittäin korkeita fosforille (97 – 99 %), kiintoaineelle (100 %), sameudelle (96 – 99 %) sekä COD:lle (38 – 55 %). Tulosten perusteella membraanitekniikkaan perustuva onttokuitusuodatus olisi tehokas ja toimiva jälkikäsittelyprosessi fosforinpoistoon ja jäteveden laadun pa-rantamiseen. Typen poistamiseen parhaiten toimi RO-membraani.