Combined electromagnetic and thermal design platform for totally enclosed induction machines

The aim of the thesis is to design a suitable thermal model that can be used as a tool for constructing the TEFC squirrel cage induction machine in addition to the electromagnetic model. A lumped-parameter thermal model is developed. The related problems and aspects of implementation are discussed in details. Losses are calculated analytically and the loss values are used in the thermal model. The sensitivity analysis is introduced to determine the most critical parameters of the model.

Multibody models for examination of touchdown bearing systems

Increased rotational speed brings many advantages to an electric motor. One of the benefits is that when the desired power is generated at increased rotational speed, the torque demanded from the rotor decreases linearly, and as a consequence, a motor of smaller size can be used. Using a rotor with high rotational speed in a system with mechanical bearings can, however, create undesirable vibrations, and therefore active magnetic bearings (AMBs) are often considered a good option for the main bearings, as the rotor then has no mechanical contact with other parts of the system but levitates on the magnetic forces. On the other hand, such systems can experience overloading or a sudden shutdown of the electrical system, whereupon the magnetic field becomes extinct, and as a result of rotor delevitation, mechanical contact occurs. To manage such nonstandard operations, AMB-systems require mechanical touchdown bearings with an oversized bore diameter. The need for touchdown bearings seems to be one of the barriers preventing greater adoption of AMB technology, because in the event of an uncontrolled touchdown, failure may occur, for example, in the bearing’s cage or balls, or in the rotor. This dissertation consists of two parts: First, touchdown bearing misalignment in the contact event is studied. It is found that misalignment increases the likelihood of a potentially damaging whirling motion of the rotor. A model for analysis of the stresses occurring in the rotor is proposed. In the studies of misalignment and stresses, a flexible rotor using a finite element approach is applied. Simplified models of cageless and caged bearings are used for the description of touchdown bearings. The results indicate that an increase in misalignment can have a direct influence on the bending and shear stresses occurring in the rotor during the contact event. Thus, it was concluded that analysis of stresses arising in the contact event is essential to guarantee appropriate system dimensioning for possible contact events with misaligned touchdown bearings. One of the conclusions drawn from the first part of the study is that knowledge of the forces affecting the balls and cage of the touchdown bearings can enable a more reliable estimation of the service life of the bearing. Therefore, the second part of the dissertation investigates the forces occurring in the cage and balls of touchdown bearings and introduces two detailed models of touchdown bearings in which all bearing parts are modelled as independent bodies. Two multibody-based two-dimensional models of touchdown bearings are introduced for dynamic analysis of the contact event. All parts of the bearings are modelled with geometrical surfaces, and the bodies interact with each other through elastic contact forces. To assist in identification of the forces affecting the balls and cage in the contact event, the first model describes a touchdown bearing without a cage, and the second model describes a touchdown bearing with a cage. The introduced models are compared with the simplified models used in the first part of the dissertation through parametric study. Damages to the rotor, cage and balls are some of the main reasons for failures of AMB-systems. The stresses in the rotor in the contact event are defined in this work. Furthermore, the forces affecting key bodies of the bearings, cage and balls can be studied using the models of touchdown bearings introduced in this dissertation. Knowledge obtained from the introduced models is valuable since it can enable an optimum structure for a rotor and touchdown bearings to be designed.

Experimental insights into deformation dynamics and intermittency in rapid granular shear flows

This work concerns the experimental study of rapid granular shear flows in annular Couette geometry. The flow is induced by continuous driving of the horizontal plate at the top of the granular bed in an annulus. The compressive pressure, driving torque, instantaneous bed height and rotational speed of the shearing plate are measured. Moreover, local stress fluctuations are measured in a medium made of steel spheres 2 and 3 mm in diameter. Both monodisperse packing and bidisperse packing are investigated to reveal the influence of size diversity in intermittent features of granular materials. Experiments are conducted in an annulus that can contain up to 15 kg of spherical steel balls. The shearing granular medium takes place via the rotation of the upper plate which compresses the material loaded inside the annulus. Fluctuations of compressive force are locally measured at the bottom of the annulus using a piezoelectric sensor. Rapid shear flow experiments are pursued at different compressive forces and shear rates and the sensitivity of fluctuations are then investigated by different means through monodisperse and bidisperse packings. Another important feature of rapid granular shear flows is the formation of ordered structures upon shearing. It requires a certain range for the amount of granular material (uniform size distribution) loaded in the system in order to obtain stable flows. This is studied more deeply in this thesis. The results of the current work bring some new insights into deformation dynamics and intermittency in rapid granular shear flows. The experimental apparatus is modified in comparison to earlier investigations. The measurements produce data for various quantities continuously sampled from the start of shearing to the end. Static failure and dynamic shearing ofa granular medium is investigated. The results of this work revealed some important features of failure dynamics and structure formation in the system. Furthermore, some computer simulations are performed in a 2D annulus to examine the nature of kinetic energy dissipation. It is found that turbulent flow models can statistically represent rapid granular flows with high accuracy. In addition to academic outcomes and scientific publications our results have a number of technological applications associated with grinding, mining and massive grain storages.

Multivariable regression analysis and hot-spot stress approach into fatigue life estimations of welded joints

Kolmen eri hitsausliitoksen väsymisikä arvio on analysoitu monimuuttuja regressio analyysin avulla. Regression perustana on laaja S-N tietokanta joka on kerätty kirjallisuudesta. Tarkastellut liitokset ovat tasalevy liitos, krusiformi liitos ja pitkittäisripa levyssä. Muuttujina ovat jännitysvaihtelu, kuormitetun levyn paksuus ja kuormitus tapa. Paksuus effekti on käsitelty uudelleen kaikkia kolmea liitosta ajatellen. Uudelleen käsittelyn avulla on varmistettu paksuus effektin olemassa olo ennen monimuuttuja regressioon siirtymistä. Lineaariset väsymisikä yhtalöt on ajettu kolmelle hitsausliitokselle ottaen huomioon kuormitetun levyn paksuus sekä kuormitus tapa. Väsymisikä yhtalöitä on verrattu ja keskusteltu testitulosten valossa, jotka on kerätty kirjallisuudesta. Neljä tutkimustaon tehty kerättyjen väsymistestien joukosta ja erilaisia väsymisikä arvio metodeja on käytetty väsymisiän arviointiin. Tuloksia on tarkasteltu ja niistä keskusteltu oikeiden testien valossa. Tutkimuksissa on katsottu 2mm ja 6mm symmetristäpitkittäisripaa levyssä, 12.7mm epäsymmetristä pitkittäisripaa, 38mm symmetristä pitkittäisripaa vääntökuormituksessa ja 25mm/38mm kuorman kantavaa krusiformi liitosta vääntökuormituksessa. Mallinnus on tehty niin lähelle testi liitosta kuin mahdollista. Väsymisikä arviointi metodit sisältävät hot-spot metodin jossa hot-spot jännitys on laskettu kahta lineaarista ja epälineaarista ekstrapolointiakäyttäen sekä paksuuden läpi integrointia käyttäen. Lovijännitys ja murtumismekaniikka metodeja on käytetty krusiformi liitosta laskiessa.

Solid and liquid biofuels markets in Finland - a study on international biofuels trade

This study considered the current situation of solid and liquid biofuels markets and international biofuels trade in Finland and identified the challenges ofthe emerging international biofuels markets for Finland. The fact that industryconsumes more than half of the total primary energy, widely applied combined heat and power production (CHP) and a high share of biofuels in the total energy consumption are specific to the Finnish energy system. One third of the electricity is generated in CHP plants. As much as 27% of the total energy consumption ismet by using wood and peat, which makes Finland the leading country in the use of biofuels. Finland has made a commitment to maintain greenhouse gas emissions at the 1990 level at the highest during the period 2008-2012. The Finnish energypolicy aims to achieve the target, and a variety of measures are taken to promote the use of renewable energy sources and especially wood fuels. In this study, the wooden raw material streams of the forest industry were included the international biofuels trade in addition to biomass streams that are traded for energy production. In 2004, as much as 45% of the raw wood importedinto Finland ended up in energy production. The total international trading of biofuels was evaluated at 72 PJ, of which the majority, 58 PJ, was raw wood. About 22% of wood based energy in Finland originated from imported raw wood. Tall oil and wood pellets composed the largest export streams of biofuels. The annual turnover of international biofuels trade was estimated at about ¤ 90 million fordirect trade and at about ¤ 190 million for indirect trade. The forest industryas the biggest user of wood, and the producer and user of wood fuels has a central position in biomass and biofuels markets in Finland. Lately, the international aspects of Finnish biofuels markets have been emphasised as the import of rawwood and the export of wood pellets have increased. Expanding the use of biofuels in the road transportation sector would increase the international streams ofbiofuels in Finland. In coming years, the international trading of biomass for energy purposes can be expected to continue growing.

Careers of Managers, Comparison between ICT and Paper Business Sectors

The purpose of this study is to increase understanding of how the managers build their early career in information and communication technology industry (ICT business sector) and pulp- and paper industry (paper business sector). The focus of the study is to explore the importance differing a business sectors have in influencing managerial careers. Business sectors can affect careers in several ways.Sectors have different history and traditions. Also the age structure of ICT personnel differs from the age structure of personnel in the paper industry. Managers in the ICT and paper sector are technically educated but in different disciplines. Differences exist also in ways of recruiting and developing commitment inpersonnel. The target group of this research, middle management engineering personnel, work in Finnish ICT and paper companies. Research data were gathered in April-December 2002 in South-Karelia by interviewing 30 managers and six directors working in three Finnish ICT companies and in three paper companies. The research issue is approached on two levels: the individual level and the organizational level. The managers related their career stories in focused interviews. Directors, representing the organizations, described the generalities of the business sector and gave background information on company policies, human relationshippractices, as well as career and human resource development. Results of the study contribute to research discussions of career, life-span reasoning, socialization and commitment. Career is conceived as a series of positions including everykind of hierarchical mobility and all kinds of positions in work. A manager's career develops in interaction with the organization and it can be seen as involving a socializing process in an organization as a consequence of experiences andchanges in positions. This research contributes to the understanding of the nature of career in the context of two business sectors. Universal career theories,for the most part, do not perceive the importance of business sector in determining career experience. This study concentrates on describing and understanding early careers in two different business areas, elements committing managers to particular business sectors and the actions of companies in that particular sector. While career research began in the middle of 1950s, the theoretical basis of career research seems to be quite fragmented still. However, a dichotomy is consistently presented between traditional, hierarchical career research and boundaryless career thinking. In this research we examine how these old and new career concepts are evidence in the ICT and paper sectors. Careers are changing from formal, hierarchy-based structures to more fluid arrangements. The new boundaryless career concept captures territory from old career thinking. Mobility between employers, networks, and changing hierarchical structures in organizations, as well as personal and family reasons are theorized to bring changes to careers patterns in the future. However, the pace of this change in careers will vary between the ICT and paper business sectors. Findings of this research indicate that business sector has an effect on how managerial careers develop. The environment where career is developed differs between ICT and paper sectors. Careers begin differently in the two environments and the speed of career progression is distinct. ICT careers are built within the business sector whereas paper careers are made inside one company. Also recruiting and socialization practices differ from one sector to the other.

A Study on Fractionation and Ultrafiltration of Proteins with Characterized Modified and Unmodified Membranes

Membrane filtration has become increasingly attractive in the processing of both foodand biotechnological products. However, the poor selectivity of the membranes and fouling are the critical factors limiting the development of UF systems for the specific fractionation of protein mixtures. This thesis gives an overview on fractionation of proteins from model protein solutions or from biological solutions. An attempt was made to improve the selectivity of the available membranes by modifying the membranes and by exploiting the different electrostatic interactions between the proteins and the membrane pore surfaces. Fractionation and UF behavior of proteins in the model solutions and in the corresponding biological solutions were compared. Characterization of the membranes and protein adsorptionto the membrane were investigated with combined flux and streaming potential studies. It has been shown that fouling of the membranes can be reduced using "self-rejecting" membranes at pH values where electrostatic repulsion is achieved between the membrane and the proteins in solution. This effect is best shown in UF of dilute single protein solutions at low ionic strengths and low pressures. Fractionation of model proteins in single, binary, and ternary solutionshas been carried out. The results have been compared to the results obtained from fractination of biological solutions. It was generally observed that fractination of proteins from biological solutions are more difficult to carry out owingto the presence of non studied protein components with different properties. Itcan be generally concluded that it is easier to enrich the smaller protein in the permeate but it is also possible to enrich the larger protein in the permeateat pH values close to the isoelectric point of the protein. It should be possible to find an optimal flux and modification to effectively improve the fractination of proteins even with very similar molar masses.

Development of rotating drum under mechanical and thermal load

A variable temperature field sets exacting demands to the structure under mechanical load. Most of all the lifetime of the rotating drum structure depends on temperature differences between parts inside the drum. The temperature difference was known because of the measurements made before. The list of demands was created based on customers’ needs. The limits of this paper were set to the inner structure of the drum. Creation of ideas for the inner structure was started open minded. The main principle in the creation process was to create new ideas for the function of the product with the help of sub-functions. The sub-functions were created as independent as possible. The best sub-functions were combined together and the new working principles were created based on them. Every working principle was calculated separately and criticized at the end of the calculation process. The main objective was to create the new kind of structure, which is not based too much to the old, inoperative structure. The affect of own weight of the inner structure to the stress values was quite small but it was also taken into consideration when calculating the maximum stress value of the structure. Because of very complex structures all of the calculations were made with the help of the ProE – Mechanica software. The fatigue analyze was made also for the best structure solution.

New Climate Change Related EC Directives and Their Interrelations to Green Electricity and Certificate Practices

Työn päätavoite on tutkia vihreän sähkön ja sertifikaattien kaupan ja EY:n uusien ilmastonmuutosta koskevien direktiivien ja direktiiviehdotusten välisiä yhteyksiä. Tutkimuksessa käsitellään direktiiviä sähköntuotannosta uusiutuvilla energialähteillä ja direktiiviehdotuksia Euroopan Unionin alueen päästökaupasta sekä yhdistetyn sähkön ja lämmön tuotannon lisäämisestä. Työ keskittyy erään suomalaisen metsäteollisuusyrityksen toimiin ilmastonmuutoksen hidastamiseksi. Tutkimus keskittyy pääosin EU:n suunnitelmaan aloittaa Unionin jäsenvaltioiden välinen päästökauppa, koska tämä järjestelmä tulee toteutuessaan olemaan teollisuuden kannalta merkittävä. Tilannetta on analysoitu neljän sellu- ja paperitehtaan hiilidioksidipäästölaskelmien avulla. Työssä kehitettyjä laskumalleja voidaan käyttää avuksi yhtiön muilla tehtailla. Tämän lisäksi työssä on luotu malli energiainvestointien arvioimiseksi tulevaisuudessa ottamalla päästöoikeuden hinnan vaikutus huomioon. Päästökaupan vaikutukset pohjoismaisilla vapautuneilla sähkömarkkinoilla on analysoity, koska teollinen sähkönhankinta on suuresti riippuvainen tästä markkinasta. Suomen metsäteollisuuden oma yhdistetty sähkön ja lämmön tuotanto erityisesti uusiutuvista energialähteistä tulee olemaan entistäkin tärkeämpää tiukentuvassa toimintaympäristössä. Tällä hetkellä on käynnissä kokeilu lisäarvon saamiseksi omalle sähköntuotannolle. Tällä haetaan kokemuksia ja valmiutta tulevaa päästökauppaa varten.

Aluminium fouling and its impact on activated carbon based dioxin and furan removal in a wet scrubber at a co-incineration plant

Dioxins and furans, PCDD/Fs, are highly toxic substances formed in post combustion zones in furnaces. PCDD/F emissions are regulated by a waste incineration directive which relates also to co-incineration plants. Several observations of dioxin and furan enhancements in wet scrub- bers have been reported previously. This is thought to be due to the so-called "memory effect" which occurs when dioxins and furans absorb into plastic material in scrubbers and desorb when ambient circumstances alter significantly. At the co-incineration plant involved, dioxins and furans are controlled with a wet scrubber, the tower packing of which is made of plastic in which activated carbon particles are dispersed. This should avoid the memory effect and act as a dioxin and furan sink since dioxins and furans are absorbed irreversibly into the packing ma- terial. In this case, the tower packing in the scrubber is covered with a white layer that has been found to be mainly aluminium. The aim of this thesis was to determine the aluminium balance and the dioxin and furan behaviour in the scrubber and, thus, the impacts that the foul- ing has on dioxin and furan removal. The source of aluminium, reasons for fouling and further actions to minimize its impacts on dioxin and furan removal were also to be discovered. Measurements in various media around the scrubber and in fuels were made and a profile analysis of PCDD/F and mass balance calculations were carried out. PCDD/F content de- creased in the scrubber. The reduced PCDD/F was not discharged into scrubbing water. The removal mechanism seems to work in spite of the fouling, at least with low PCDD/F loads. Most of the PCDD/F in excess water originates from the Kymijoki River which is used as feeding water in the scrubber. Fouling turned out to consist mainly of aluminium hydroxides. Sludge combusted in the furnace was found to be a significant source of aluminium. Ways to minimize the fouling would be adjustment of pH to a proper lever, installation of a mechanical filter to catch the loose material from the scrubbing water and affecting the aluminium content of the sludge.

The effects of selective estrogen receptor modulators on the death of breast cancer cells and osteoblastic cells

Selektiivisten estrogeenireseptorin muuntelijoiden (serm) vaikutus rintasyöpäsolujen ja luun solujen kuolemaan Selektiiviset estrogeenireseptorin muuntelijat (SERMit) ovat ryhmä kemialliselta rakenteeltaan erilaisia yhdisteitä jotka sitoutuvat solunsisäisiin estrogeenireseptoreihin toimien joko estrogeenin kaltaisina yhdisteinä tai estrogeenin vastavaikuttajina. Tamoksifeeni on SERM –yhdiste, jota on jo pitkään käytetty estrogeenireseptoreita (ER) ilmentävän rintasyövän lääkehoidossa. Tamoksifeeni sekä estää rintasyöpäsolujen jakaantumista että toisaalta aikaansaa niiden apoptoosin eli ohjelmoidun solukuoleman muuntelemalla ER-välitteisesti kohdesolun geenien ilmentymistä. Viimeaikaiset tutkimustulokset ovat kuitenkin osoittaneet tamoksifeenilla olevan myös nopeampia, nongenomisia vaikutusmekanismeja. Tässä väitöskirjatyössä tutkimme niitä nopeita vaikutusmekanismeja joiden avulla tamoksifeeni vaikuttaa rintasyöpäsolujen elinkykyyn. Osoitamme että tamoksifeeni farmakologisina pitoisuuksina aikaansaa nopean mitokondriaalisen solukuolemaan johtavan signallointireitin aktivoitumisen rintasyöpäsoluissa. Tämän lisäksi tutkimme myös tamoksifeenin aiheuttamaan mitokondriovaurioon johtavia tekijöitä. Tutkimustuloksemme osoittavat että ER-positiivisissa rintasyöpäsoluissa tamoksifeeni indusoi pitkäkestoisen ERK-kinaasiaktivaation, joka voidaan estää 17-beta-estradiolilla. Tamoksifeenin aikaansaama nopea solukuolema on pääosin ER:sta riippumaton tapahtuma, mutta siihen voidaan vaikuttaa myös ER-välitteisin mekanismein. Sen sijaan epidermaalisen kasvutekijäreseptorin (EGFR) voitiin osoittaa osallistuvan tamoksifeenin nopeiden vaikutusten välittämiseen. Tämän lisäksi vertailimme myös estradiolin ja eri SERM-yhdisteiden kykyä suojata apoptoosilta käyttämällä osteoblastiperäisiä soluja. Pytyäksemme vertailemaan ER-isotyyppien roolia eri yhdisteiden suojavaikutuksissa, transfektoimme U2OS osteosarkoomasolulinjan ilmentämään pysyvästi joko ERalfaa tai ERbetaa. Tulostemme mukaan sekä estradioli että uusi SERM-yhdiste ospemifeeni suojaavat osteoblastin kaltaisia soluja etoposidi-indusoidulta apoptoosilta. Sekä ERalfa että ERbeta pystyivät välittämään suojavaikutusta, joskin vaikutukset erosivat toisistaan. Lisäksi havaitsimme edellä mainitun suojavaikutuksen olevan yhteydessä muutoksiin solujen sytokiiniekspressiossa. Tietoa SERM-yhdisteiden anti-ja proapoptoottisten vaikutusmekanismeista eri kohdekudoksissa voidaan mahdollisesti hyödyntää kehiteltäessä uusia kudosspesifisiä SERM-yhdisteitä.

IEA Bioenergy Task 40 “Sustainable International Bioenergy Trade: Securing supply and demand” Country report of Finland 2008

This study considered the current situation of biofuels markets in Finland. The fact that industry consumes more than half of the total primary energy, widely applied combined heat and power production and a high share of solid biomass fuels in the total energy consumption are specific to the Finnish energy system. Wood is the most important source of bioenergy in Finland, representing 21% of the total energy consumption in 2006. Almost 80% of the wood-based energy is recovered from industrial by-products and residues. Finland has commitment itself to maintaining its greenhouse gas emissions at the 1990 level, at the highest, during the period 2008–2012. The energy and climate policy carried out in recent years has been based on the National Energy and Climate introduced in 2005. The Finnish energy policy aims to achieve the target, and a variety of measures are taken to promote the use of renewable energy sources and especially wood fuels. In 2007, the government started to prepare a new long-term (up to the year 2050) climate and energy strategy that will meet EU’s new targets for the reduction of green house gas emissions and the promotion of renewable energy sources. The new strategy will be introduced during 2008. The international biofuels trade has a substantial importance for the utilisation of bioenergy in Finland. In 2006, the total international trading of solid and liquid biofuels was approximately 64 PJ of which import was 61 PJ. Most of the import is indirect and takes place within the forest industry’s raw wood imports. In 2006, as much as 24% of wood energy was based on foreignorigin wood. Wood pellets and tall oil form the majority of export streams of biofuels. The indirect import of wood fuels increased almost 10% in 2004–2006, while the direct trade of solid and liquid biofuels has been almost constant.

Ultralujasta teräksestä valmistetun henkilönostimen teleskooppipuomin kehittäminen

Tässä työssä kehitettiin palo- ja pelastuskäyttöön tarkoitettuun henkilönostimeen teleskooppipuomin profiilit. Profiilien valmistusmateriaalina oli kuumavalssattu, ultraluja säänkestävä rakenneteräs. Työssä kehitettiin standardien ja ohjeiden pohjalta laskentapohja, jolla voidaan tutkia teleskooppipuomin jaksojen tukireaktioita, taivutus- ja vääntömomentteja ja leikkaus ja normaalivoimia. Laskentapohjassa voidaan varioida eri kuormitusten suuntia, teleskooppipuomin sivusuuntaista ulottumaa ja nostokulmaa. Profiilien alustavassa mitoituksessa hyödynnettiin paikallisen lommahduksen huomioon ottavia standardeja ja suunnitteluohjeita. Eri poikkileikkausten ominaisuuksia verrattiin keskenään ja profiili valittiin yhdessä kohdeyrityksen kanssa. Alustavan mitoituksen yhteydessä muodostettiin apuohjelma valitulle poikkileikkaukselle, jolla voitiin tutkia profiilin eri muuttujien vaikutusta mm. paikalliseen lommahdukseen ja jäykkyyteen. Laskentapohjaan sisällytettiin myös optimointirutiini, jolla voitiin minimoida poikkileikkauksen pinta-ala ja tätä kautta profiilin massa. Lopullinen mitoitus suoritettiin elementtimenetelmällä. Mitoituksessa tutkittiin alustavasti mitoitettujen profiilien paikallista lommahdusta lineaarisen stabiilius- ja epälineaarisen analyysin pohjalta. Profiilien jännityksiä tutkittiin tarkemmin mm. varioimalla kuormituksia ja osittelemalla elementtien normaalijännityksiä. Diplomityössä kehitetyllä ja analysoidulla teleskooppipuomilla voitiin keventää jaksojen painoja 15-30 %. Sivusuuntainen ulottuma parani samalla lähes 20 % ja nimelliskuorma kasvoi 25 %.

Market of biomass fuels in Finland : IEA Bioenergy Task 40 and EUBIONET III - Country report of Finland 2009

This study considered the current situation of solid and liquid biomass fuels in Finland. The fact that industry consumes more than half of the total primary energy, widely applied combined heat and power production and a high share of solid biomass fuels in the total energy consumption are specific to the Finnish energy system. Wood is the most important source of bioenergy in Finland, representing 20% of the total energy consumption in 2007. Almost 80% of the woodbased energy is recovered from industrial by-products and residues. As a member of the European Union, Finland has committed itself to the Union’s climate and energy targets, such as reducing its overall emissions of green house gases to at least 20% below 1990 levels by 2020, and increasing the share of renewable energy in the gross final consumption. The renewable energy target approved for Finland is 38%. The present National Climate and Energy Strategy was introduced in November 2008. The strategy covers climate and energy policy measures up to 2020, and in brief thereafter, up to 2050. In recent years, the actual emissions have exceeded the Kyoto commitment and the trend of emissions is on the increase. In 2007, the share of renewable energy in the gross final energy consumption was approximately 25% (360 PJ). Without new energy policy measures, the final consumption of renewable energy would increase to 380 PJ, which would be approximately only 31% of the final energy consumption. In addition, green house gas emissions would exceed the 1990 levels by 20%. Meeting the targets will need the adoption of more active energy policy measures in coming years. The international trade of biomass fuels has a substantial importance for the utilisation of bioenergy in Finland. In 2007, the total international trading of solid and liquid biomass fuels was approximately 77 PJ, of which import was 62 PJ. Most of the import is indirect and takes place within the forest industry’s raw wood imports. In 2007, as much as 21% of wood energy was based on foreign-origin wood. Wood pellets and tall oil form the majority of export streams of biomass fuels. The indirect import of wood fuels peaked in 2006 to 61 PJ. The foreseeable decline in raw wood import to Finland will decrease the indirect import of wood fuels. In 2004– 2007, the direct trade of solid and liquid biomass fuels has been on a moderate growth path. In 2007, the import of palm oil and export of bio-diesel emerged, as a large, 170 000 t/yr biodiesel plant came into operation in Porvoo.