Modeling of water/steam circulation in Circulating Fluidized Bed boiler

A distinctive design feature of steam boiler with natural circulation is the presence of the steam drum which plays a role of the separator of vapor from the flow of water-and-steam mixture coming into steam drum from the furnace tubes. Steam drum with unheated downcomer tubes, deducing from it, and riser (screen/furnace tubes) inside the furnace is a closed circulation loop in which movement of water (downcomer tubes) and water-and-steam mixture (riser tubes) is organized. The movement of the working fluid is appears due to occurrence of the natural pressure, determined by the difference in hydrostatic pressure and the mass of water and water-and-steam mixtures in downcomer and riser tubes and called the driving pressure of the natural circulation: S drive = H steam (ρ down + ρ mix) g where: ρ down - density of water in downcomer tubes; ρ mix - density of water in riser tubes; H steam - height of steam content section; g - acceleration of gravity. In steam boilers with natural circulation the circulation rate is usually between 10 and 30. Thus, consumption of water in the circulation circuit “circulation rate times” more than steam output of the boiler. There are two aspects of the design of natural water circulation loops. One is to ensure a sufficient mass flux of circulating water to avoid burnout of evaporator tubes. The other is to avoid tube wall temperature fluctuation and tube vibration due to oscillation of circulation velocity. The design criteria are therefore reduced, in principle, to those of critical heat flux, critical flow rate for burnout, and flow instability. In practical design, however, the circulation velocity and the void fraction at the evaporator tube outlet are used as the design criteria (Seikan I., et. al., 1999). This study has been made with assumption that the heat flux in the furnace of the boiler even all the time. The target of the study was to define the circulation rate of the boiler, thus average heat flux do not change it. I would like to acknowledge professionals from “Foster Wheeler” company for good and comfortable cooperation.

Hoitoketjun kustannukset perusterveydenhuollosta erikoissairaanhoitoon: Case Lappeenranta ja Imatra

Työn tavoitteena oli selvittää perusterveydenhuollon ja erikoissairaanhoidon välillä kulkevien lappeenrantalaisten (34 potilasta) ja imatralaisten (20 potilasta) hoitoketjun kustannukset ja hoitoajat, sekä analysoida niitä. Kustannusten ja hoitoketjun läpimenoaikojen esittämisessä käytettiin kustannuskertymäajattelua. Tutkimuksessa tutkittiin prosessien ohjauksen ja toiminnanohjauksen teoriaa sekä terveydenhuollossa että teollisuudessa, ja kustannuslaskennan perusteita. Huomattiin, että erityisesti lean -ajattelua voidaan käyttää myös terveydenhuollossa ja hoitoketjuja tarkasteltaessa. Empiirisessä osuudessa tarkasteltiin Lappeenrannan ja Imatran tutkittavien kolmen potilasryhmän kustannuksia ja hoitoaikoja kustannuskertymäkäyrien avulla. Tarkastelussa olivat kaupunkien ja potilasryhmien maksimi-, minimi- ja mediaanikustannuspotilaan hoitoketjun kustannukset ja läpimenoajat. Keskeisenä tuloksena havaittiin, että perusterveydenhuollon osuus kustannuksista oli suuri etenkin potilailla, joilla oli pitkä läpimenoaika hoitoketjussa, sillä hoitoaika painottui tällöin terveyskeskussairaalaan. Hyvin lyhyen läpimenoajan potilailla taas erikoissairaanhoidon osuus kustannuksista oli suurempi, mutta tällaiset potilaat olivat lähinnä minimi-, tai korkeintaan mediaanikustannuspotilaita. Päiväkohtainen kustannus havaittiin erikoissairaanhoidossa korkeammaksi, mutta perusterveydenhuollon terveyskeskussairaalahoito nousi maksimikustannuspotilailla aina selvästi suurimmaksi kustannuksen aiheuttajaksi. Havaittiin myös, että potilaiden lyhyt keskussairaalahoito ei takaa alentuneita hoitoketjun kokonaiskustannuksia. Työssä havaittiin, että perusterveydenhuollon toimivuus on koko terveydenhuollon toimivuuden ja tuottavuuden selkäranka. Erityisesti keskeisiä osia, mihin tulee kiinnittää huomiota hoitoketjussa, ovat potilaan sijoittaminen oikeinkeskussairaalahoitoon tultaessa ja sieltä lähdettäessä. Muun muassa näillä tavoilla voidaan karsia potilaiden ylipitkiä hoitojaksoja perusterveydenhuollossa tai potilaan jäämistä kiertämään hoitoketjuun.

Effect of Noncondensable Gases on Circulation of Primary Coolant in Nuclear Power Plants in Abnormal Situations

The present study focuses on two effects of the presence of a noncondensable gas on the thermal-hydraulic behavior of thecoolant of the primary circuit of a nuclear reactor in the VVER-440 geometry inabnormal situations. First, steam condensation with the presence of air was studied in the horizontal tubes of the steam generator (SG) of the PACTEL test facility. The French thermal-hydraulic CATHARE code was used to study the heat transfer between the primary and secondary side in conditions derived from preliminary experiments performed by VTT using PACTEL. In natural circulation and single-phase vapor conditions, the injection of a volume of air, equivalent to the totalvolume of the primary side of the SG at the entrance of the hot collector, did not stop the heat transfer from the primary to the secondary side. The calculated results indicate that air is located in the second half-length (from the mid-length of the tubes to the cold collector) in all the tubes of the steam generator The hot collector remained full of steam during the transient. Secondly, the potential release of the nitrogen gas dissolved in the water of the accumulators of the emergency core coolant system of the Loviisa nuclear power plant (NPP) was investigated. The author implemented a model of the dissolution and release ofnitrogen gas in the CATHARE code; the model created by the CATHARE developers. In collaboration with VTT, an analytical experiment was performed with some components of PACTEL to determine, in particular, the value of the release time constant of the nitrogen gas in the depressurization conditions representative of the small and intermediate break transients postulated for the Loviisa NPP. Such transients, with simplified operating procedures, were calculated using the modified CATHARE code for various values of the release time constant used in the dissolution and release model. For the small breaks, nitrogen gas is trapped in thecollectors of the SGs in rather large proportions. There, the levels oscillate until the actuation of the low-pressure injection pumps (LPIS) that refill the primary circuit. In the case of the intermediate breaks, most of the nitrogen gas is expelled at the break and almost no nitrogen gas is trapped in the SGs. In comparison with the cases calculated without taking into account the release of nitrogen gas, the start of the LPIS is delayed by between 1 and 1.75 h. Applicability of the obtained results to the real safety conditions must take into accountthe real operating procedures used in the nuclear power plant.

Separation of Gas Bubbles from Circulation Waters and Pulp Suspensions in Open Channel Flow

The objective of this thesis was to study the removal of gases from paper mill circulation waters experimentally and to provide data for CFD modeling. Flow and bubble size measurements were carried out in a laboratory scale open gas separation channel. Particle Image Velocimetry (PIV) technique was used to measure the gas and liquid flow fields, while bubble size measurements were conducted using digital imaging technique with back light illumination. Samples of paper machine waters as well as a model solution were used for the experiments. The PIV results show that the gas bubbles near the feed position have the tendency to escape from the circulation channel at a faster rate than those bubbles which are further away from the feed position. This was due to an increased rate of bubble coalescence as a result of the relatively larger bubbles near the feed position. Moreover, a close similarity between the measured slip velocities of the paper mill waters and that of literature values was obtained. It was found that due to dilution of paper mill waters, the observed average bubble size was considerably large as compared to the average bubble sizes in real industrial pulp suspension and circulation waters. Among the studied solutions, the model solution has the highest average drag coefficient value due to its relatively high viscosity. The results were compared to a 2D steady sate CFD simulation model. A standard Euler-Euler k-ε turbulence model was used in the simulations. The channel free surface was modeled as a degassing boundary. From the drag models used in the simulations, the Grace drag model gave velocity fields closest to the experimental values. In general, the results obtained from experiments and CFD simulations are in good qualitative agreement.

Modeling of water/steam circulation in Circulating Fluidized Bed boiler

A distinctive design feature of steam boiler with natural circulation is the presence of the steam drum which plays a role of the separator of vapor from the flow of water-and-steam mixture coming into steam drum from the furnace tubes. Steam drum with unheated downcomer tubes, deducing from it, and riser (screen/furnace tubes) inside the furnace is a closed circulation loop in which movement of water (downcomer tubes) and water-and-steam mixture (riser tubes) is organized. The movement of the working fluid is appears due to occurrence of the natural pressure, determined by the difference in hydrostatic pressure and the mass of water and water-and-steam mixtures in downcomer and riser tubes and called the driving pressure of the natural circulation:

Exit times for some processes with normally distributed noise

Denna avhandling handlar om metoder för att hitta begränsningar för det asymptotiska beteendet hos en förväntad uthoppstid från ett område omkring en xpunkt för processer som har normalfördelad störning. I huvudsak behandlas olika typer av autoregressiva processer. Fyra olika metoder används. En metod som använder principen för stora avvikelser samt en metod som jämför uthoppstiden med en återkomsttid ger övre begränsningar för den förväntade uthoppstiden. En martingalmetod och en metod för normalfördelade stokastiska variabler ger undre begränsningar. Metoderna har alla både förtjänster och nackdelar. Genom att kombinera de olika metoderna får man de bästa resultaten. Vi får fram gränsvärdet för det asymptotiska beteendet hos en uthoppstid för den multivariata autoregressiva processen, samt motsvarande gränsvärde för den univariata autoregressiva processen av ordning n.

The Cycle Times of Working Capital: Financial Value Chain Analysis Method

Interest towards working capital management increased among practitioners and researchers because the financial crisis of 2008 caused the deterioration of the general financial situation. The importance of managing working capital effectively increased dramatically during the financial crisis. On one hand, companies highlighted the importance of working capital management as part of short-term financial management to overcome funding difficulties. On the other hand, in academia, it has been highlighted the need to analyze working capital management from a wider perspective namely from the value chain perspective. Previously, academic articles mostly discussed working capital management from a company-centered perspective. The objective of this thesis was to put working capital management in a wider and more academic perspective and present case studies of the value chains of industries as instrumental in theoretical contributions and practical contributions as complementary to theoretical contributions and conclusions. The principal assumption of this thesis is that selffinancing of value chains can be established through effective working capital management. Thus, the thesis introduces the financial value chain analysis method which is employed in the empirical studies. The effectiveness of working capital management of the value chains is studied through the cycle time of working capital. The financial value chain analysis method employed in this study is designed for considering value chain level phenomena. This method provides a holistic picture of the value chain through financial figures. It extends the value chain analysis to the industry level. Working capital management is studied by the cash conversion cycle that measures the length (days) of time a company has funds tied up in working capital, starting from the payment of purchases to the supplier and ending when remittance of sales is received from the customers. The working capital management practices employed in the automotive, pulp and paper and information and communication technology industries have been studied in this research project. Additionally, the Finnish pharmaceutical industry is studied to obtain a deeper understanding of the working capital management of the value chain. The results indicate that the cycle time of working capital is constant in the value chain context over time. The cash conversion cycle of automotive, pulp and paper, and ICT industries are on average 70, 60 and 40 days, respectively. The difference is mainly a consequence of the different cycle time of inventories. The financial crisis of 2008 affected the working capital management of the industries similarly. Both the cycle time of accounts receivable and accounts payable increased between 2008 and 2009. The results suggest that the companies of the automotive, pulp and paper and ICT value chains were not able to self-finance. Results do not indicate the improvement of value chains position in regard to working capital management either. The findings suggest that companies operating in the Finnish pharmaceutical industry are interested in developing their own working capital management, but collaboration with the value chain partners is not considered interesting. Competition no longer occurs between individual companies, but between value chains. Therefore the financial value chain analysis method introduced in this thesis has the potential to support value chains in improving their competitiveness.

Intensification of Operation of Inclined Plate Settler at Fertilizer Plant

Fertilizer plant’s process waters contain high concentrations of nitrogen compounds, such as ammonium and nitrate. Phosphorus and fluorine, which originate from phosphoric acid and rock phosphate (apatite) used in fertilizer production, are also present. Phosphorus and nitrogen are the primary nutrients causing eutrophication of surface waters. At fertilizer plant process waters are held in closed internal circulation. In a scrubber system process waters are used for washing exhaust gases from fertilizer reactors and dry gases from granulation drums as well as for cooling down the fertilizer slurry in neutralization reactor. Solids in process waters are separated in an inclined plate settler by gravitational sedimentation. However, the operation of inclined plate settler has been inadequate. The aim of this thesis was to intensify the operation of inclined plate settler and thus the solids separation e.g. through coagulation and/or flocculation process. Chemical precipitation was studied to reduce the amount of dissolved species in process waters. Specific interest was in precipitation of nitrogen, phosphorus, and fluorine containing specimens. Amounts of phosphorus and fluorine were reduced significantly by chemical precipitation. When compared to earlier studies, annual chemical costs were almost eight times lower. Instead, nitrogen compounds are readily dissolved in water, thus being difficult to remove by precipitation. Possible alternative techniques for nitrogen removal are adsorption, ion exchange, and reverse osmosis. Settling velocities of pH adjusted and flocculated process waters were sufficient for the operation of inclined plate settler. Design principles of inclined plate settler are also presented. In continuation studies, flow conditions in inclined plate settler should be modelled with computational fluid dynamics and suitability of adsorbents, ion exchange resins, and membranes should be studied in laboratory scale tests.

Cool Cats Don’t Dig the Squares” - The New York Times ja beat-sukupolvi, opiskelijamellakat ja hipit vuosina 1952-1969

Beat-sukupolvi, opiskelijoiden poliittinen aktiivisuus ja hipit olivat tunnettuja ilmiöitä Yhdysvalloissa 1950- ja 1960-luvuilla. Ilmiöillä oli paljon yhteistä ja ne vaikuttivat toisiinsa merkittävästi. Tätä yhteyttä ei aina tuoda esiin. Tämä tutkielma tuo esiin sen, miten The New York Times kirjoitti ilmiöistä. Tutkimus kertoo myös, miten The New York Times yhdistää ilmiöt keskenään. Sen lisäksi tulee esiin The New York Timesin näkemys ilmiöiden taustoista suhteessa nuorisokulttuuriin. Tutkimuksen kohteena on The New York Timesin lehtiartikkeleita vuosilta 1952-1969. Tutkimuksen pääkysymykset ovat: Miten The New York Times suhtautui beat-sukupolveen ja nuorisokulttuurin muutokseen? Miten The New York Times suhtautui yliopisto-opiskelijoihin ja heidän suhteeseensa nuorisokulttuurin muutokseen sekä miten The New York Times näkee hippien muuttavan yhteiskuntaa? Ensimmäistä pääkysymystä tarkastelen kahden alakysymyksen kautta: Miten beat-sukupolven synty esitetään The New York Timesissa, ja toisaalta millaisen kuvan The New York Times antaa beat-sukupolven vaikutuksesta nuorisoon? Toista pääkysymystä käsittelen kysymällä: Miten The New York Times näki nuorten poliittisen vaikuttavuuden nousun ja miten lehti suhtautui ajanjakson yliopistomellakoihin?. Kolmannessa luvussa tarkastelen pääkysymystä kysymällä: Keitä hipit olivat, ja olivatko hipit poliittisesti aktiivisia vai ei? Tutkimuksesta selviää, että The New York Times pyrkii kuvaamaan ilmiöitä mahdollisimman objektiivisesti. Lehti antaa ilmiöitä kuvatessa asioihin hyvin perehtyneiden henkilöiden esittää ilmiö. Sen jälkeen lehti antaa lukijoiden ja muiden asiantuntijoiden kommentoida. The New York Times näkee näiden ilmiöiden yhteyden ja se tulee voimakkaasti esille laajoissa artikkeleissa. Lyhyemmissä uutisissa yhteyttä ei aina näe, ja terminologia on yleistävämpi, tekstin eri tarkoitusperän takia. Kaiken kaikkiaan The New York Times tuo esiin mahdollisimman vähän moralisoivaa kuvaa ilmiöistä ja tuo esiin niiden keskinäisiä suhteita. Tuloksista näkee, että The New York Times on arvoiltaan vapaamielinen lehti, joka uutisoi, näiden aiheiden perusteella, kattavasti koko Yhdysvaltoja koskevista tapahtumista.

Open Access in Times of Knowledge Unlatched : Cooperative Action for Books and Journals

Presentation at the seminar "Publishers and Funders for OA in Finland", Helsinki, May 24, 2016